HP ZR2440W - Manual

2 Setting Up the Monitor To set up the monitor, ensure that the power is turned off to the monitor, computer system, and otherattached devices, then follow the instructions below. NOTE: Be sure the master power switch, located on the rear panel of the monitor, is in the off position. The master powe...

Models ZR2240w, ZR2440w, and ZR2740w use the HP Quick Release 2 mechanism for easy movingof the monitor. To mount the panel onto the pedestal: 1. Slide the mounting plate on the pedestal under the upper lip of the recess in the back of thepanel. 2. Lower the pedestal into the recess until it snaps i...

Routing and Connecting the Cables Place the monitor in a convenient, well-ventilated location near the computer. ZR2040w Model The cable-restraining bar on the pedestal of the ZR2040w is held in place by four tabs. Figure 2-7 Cable-Restraining Bar 1. To remove the bar, first pull one end of the bar ...

3. Connect the desired signal sources. Refer to the drawings in ( Rear Components on page 6 ) to identify the connectors on your monitor. For each one, plug in one end of the appropriate cable.Attach the other end to your computer or other video source. The ZR2440w model supports audio output from t...

Mounting a Quick-Release Panel The ZR2240w, ZR2440w and ZR2740w support mounting to VESA-compliant hardware in two ways: ● Remove the HP stand and use the 4 VESA mount threaded holes (100 x 100 pattern) that are inthe Quick Release 2 recess. Screws of the appropriate length are provided. Figure 2-13...

6. Attach the mounting plate to the wall or swing arm of your choice. Figure 2-17 Installing the Mounting Plate CAUTION: This monitor supports the VESA industry standard 100 mm mounting holes. To attach a third-party mounting solution to the monitor, four 4 mm, 0.7 pitch, and 10 mm longscrews are re...

Identifying information is located on the pull-out card (instead of on labels on the back of the monitor).Warranty support information (model number, serial number, product number) is printed on the frontof the card and regulatory information is printed on the back of the card. Installing a Cable Lo...

Adjusting the Monitor 1. Tilt the monitor's panel forward or backward to set it to a comfortable eye level. Figure 2-20 Adjusting the Tilt 2. If your monitor has the ability to swivel, adjust it to the left or right for the best viewing angle. Figure 2-21 Adjusting the Viewing Angle (Select Models) ...

Portrait Orientation The ZR2040w must be mounted in the orientation you wish to use. Other models can be pivoted aftermounting. To do this, raise the panel to its highest position and pivot it clockwise from landscape toportrait. Figure 2-23 Pivoting the Monitor (Select Models) NOTE: It may be neces...

3 Operating the Monitor Overview of Operation If you are not familiar with HP Performance monitors, read this section for an overview of how theyoperate. This will help you locate specific information elsewhere in this manual. Your monitor provides for more than one source of input. It will scan the...

4 Locating Additional Information Refer to the HP LCD Monitors Reference Guide included on the CD with your monitor for additional information on: ● Optimizing monitor performance ● Safety and maintenance guidelines ● Installing software from the CD ● Using the OSD menu ● Downloading software from t...

A Technical Specifications NOTE: All performance specifications are provided by the component manufacturers. Performance specifications represent the highest specification of all HP's component manufacturers' typical levelspecifications for performance and actual performance may vary either higher o...

Table A-4 ZR2440w High Definition Video Formats (continued) 13 1080p25 1920 x 1080 28.125 25 74.250 33 1080p-25Hz 14 1080p29.97 1920 x 1080 33.750 30 74.250 34 1080p-30Hz ZR2740w Model Preset Modes Preset Pixel Format Horizontal Frequency(kHz) Vertical Frequency(Hz) 1 640 x 480 31.468 59.9 2 1280 x ...