Hotpoint Washing Machine Manual

Page 2 - Electric and water connections; Connecting the water inlet hose; Installation; Unpacking and levelling; Unpacking; Levelling

2 GB 2. If the floor is not perfectly level, compensate for any unevenness by tightening or loosening the adjustable front feet (see figure) ; the an- gle of inclination, measured according to the worktop, must not exceed 2°. Levelling your appliance correctly will provide it with stability and avoi...

Page 4 - Technical data; The first wash cycle

4 GB Technical data Model BHWMD 732 Dimensions width 59.5 cm height 81.5 cm depth 54.5 cm Capacity from 1 to 7 kg Electrical connections please refer to the technical data plate fixed to the ma- chine Water con- nections maximum pressure 1 MPa (10 bar) minimum pressure 0.05 MPa (0.5 bar) drum capaci...

Page 6 - Instructions for the fitter

6 GB Instructions for the fitter Mounting the wooden panel onto the door and in-serting the machine into cabinets: In the case where the machine must be shipped for final installation after the wooden panel has been mounted, we suggest leaving it in its original packaging. The packaging was designed...

Page 8 - Care and maintenance

8 GB Care and maintenance Cutting off the water and electri- city supplies • Turn off the water tap after every wash cycle. This will limit wear on the hydraulic system in- side the washing machine and help to prevent leaks. • Unplug the washing machine when cleaning it and during all maintenance wo...

Page 9 - Opening the porthole door manually; Precautions and tips; General safety

GB 9 their local authority or retailer for information concerning the correct disposal of their old appliance. Opening the porthole door manually In the event that it is not possible to open the porthole door due to a powercut, and if you wish to remove the laundry, proceed as follows: 1. remove the...

Page 10 - Description of the washing machine; Control panel

10 GB Detergent dispenser drawer: used to dispense deter- gents and washing additives (see “Detergents and laundry”) . ON/OFF button : press this briefly to switch the ma- chine on or off. The START/PAUSE indicator light, which flashes slowly in a green colour shows that the machine is switched on. ...

Page 11 - Display

GB 11 Display The display is useful when programming the machine and provides a great deal of information. The two upper strings A and B provide details of the wash cycle selected, the wash cycle phase in progress and all informa- tion relating to the progress status of the wash cycle. String C show...

Page 12 - Running a wash cycle

12 GB Running a wash cycle 1. SWITCH THE MACHINE ON. Press the On/Off button ; the text HELLO will appear on the display and the START/PAUSE indicator light will flash slowly in a green colour. 2. LOAD THE LAUNDRY. Open the porthole door. Load the laundry, making sure you do not exceed the maximum l...

Page 13 - Wash cycles and functions; Wash functions; Table of wash cycles

GB 13 Wash cycles and functions Wash functions Super Wash Because a greater quantity of water is used in the initial phase of the cycle, and because of the increased cycle duration, this function offers a high-performance wash. ! It cannot be used with the , , , , “Spin” and “Pump out”. Extra rinse ...

Page 14 - Detergents and laundry; Special wash cycles; Load balancing system

14 GB Detergent dispenser drawer Good washing results also depend on the correct dose of detergent: adding too much detergent will not necessarily result in a more efficient wash, and may in fact cause a build up on the inside of your appliance and contribute to environmental pollution. ! Use powder...

Page 15 - Troubleshooting

GB 15 Troubleshooting Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”) , make sure that the problem cannot be solved easily using the following list. Problem: The machine does not switch on. The wash cycle does not start. The machine does ...

Page 17 - Assistance

GB 17 Assistance Before calling for Assistance: • Check whether you can solve the problem alone ( see “Troubleshooting” ); • Restart the programme to check whether the problem has been solved;• If this is not the case, contact an authorised Technical Assistance Centre using the telephone number prov...