Page 3 - IMPORTANT PRECAUTIONS; SAVE THESE INSTRUCTIONS
3 IMPORTANT PRECAUTIONS SAVE THESE INSTRUCTIONS When using an exercise product, basic precautions should always be followed, including the following: Read all instructions before using this indoor cycle. It is the responsibility of the owner to ensure that all users of this indoor cycle are adequate...
Page 4 - READ AND SAVE ALL INSTRUCTIONS bEfORE ASSEmbLINg OR USINg THIS; wARNINg
4 READ AND SAVE ALL INSTRUCTIONS bEfORE ASSEmbLINg OR USINg THIS INDOOR CyCLE. IT IS STRONgLy RECOmmENDED TO TAkE THE fOLLOwINg SAfETy INSTRUCTIONS. • CAUTION: If you experience chest pains, nausea, dizziness or shortness of breath, stop exercising immediately and consult your physician before conti...
Page 5 - ASSEMBLY
5 ASSEMBLY There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the indoor cycle could have...
Page 6 - PARTS INCLUDED
6 TOOLS/fASTENERS INCLUDED: F Socket Head Screw F 5 mm Allen Wrench F Open Wrench (#13 / #14 / #15) PARTS INCLUDED: A) Main Frame AssemblyB) Handlebar SetC) SeatD) Rear FootE) Front FootF) PedalsG) Quick Release Lever SetH) Hardware Kit If you have questions or if there are any missing parts, contac...
Page 7 - PRE
7 This unit weighs 118 lbs / 54 kg. To avoid injury to the user and the unit, be sure to have proper assistance to remove or move the unit. CAUTION UNPACkINg The P8000 Indoor Cycle is carefully inspected before it is packaged. Remove all parts from the shipping carton and foam inserts, and verify th...
Page 9 - NOTE; LEfT; COUNTERCLOCkwISE
9 ASSEMBLY STEP 2 G11 G10 A Install the pedals on the pedal cranks by using the Open Wrench (Z32). The closed end of the pedal cage must point forward, toward the front of the cycle. NOTE : Be careful to align the threads correctly to avoid damage. A little grease on the threads should help the peda...
Page 11 - INDOOR CYCLE OPERATION
11 INDOOR CYCLE OPERATION P8000 SPECIfICATIONS TECHNICAL DATA SPECIAL FEATURES *specifications are subject to change without notice. FrameResistance TechnologyResistance LevelsDrive SystemFlywheelHandlebar AdjustmentsSeat AdjustmentsDimensions (LxWxH)Product WeightMax User Weight Handlebar DesignCra...
Page 12 - SEAT ADJUSTmENT; HANDLEbAR ADJUSTmENT; PEDAL STRAP ADJUSTmENT
12 SEAT ADJUSTmENT Proper seat height helps ensure maximum exercise efficiency and comfort, while reducing the risk of injury. Adjust the seat height to make sure of this proper position: • The knee joint is slightly flexed when the extended leg is at the bottom of the pedal stroke. • Your foot ankl...
Page 13 - mOVINg THE CyCLE; STAbILIzINg THE CyCLE
13 RESISTANCE ADJUSTmENT The micro-adjust resistance knob is located just below the handlebars on the bike frame, for easier pedaling resistance control. Turn the knob in a clockwise direction to increase pedal resistance. Turn the knob in a counter clockwise direction to decrease pedal resistance. ...
Page 14 - mAINTENANCE
14 mAINTENANCE The safety level given by the design of the P8000 Indoor Cycle can only be maintained when the equipment is regularly examined for damage and wear. Inoperable components should be replaced or the equipment should be put out of use until it is repaired. DAILy • Wipe down the Indoor Cyc...
Page 15 - LImITED HOmE USE wARRANTy; EXCLUSIONS AND LImITATIONS
15 LImITED HOmE USE wARRANTy wEIgHT CAPACITy = 350 lbs (159 kilograms). fRAmE • LIFETIME Horizon Fitness warrants the frame against defects in workmanship and materials for the lifetime of the original owner. (The frame is defined as the welded metal base of the unit and does not include any parts t...
Page 16 - CUSTOMER TECH SUPPORT
P8000 Rev. 1.0 | © 2009 Horizon Fitness | Designed & Engineered in the U.S.A. | Made in China Tel: 1-800-244-4192 Email: [email protected] Horizon fitness1600 Landmark Drive, Cottage grove wI, 53527 DO NOT RETURN TO THE RETAILER if you have any problems during assembly or if parts are ...