Hoover WindTunnel Upright Bag Vacuum Cleaner- User Manual

Page 2 - ENGLISH; Review this manual before; Important Safeguards!; READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE; Save these instructions!; Index

Fill in and retain The model and serial number are located on the bottom of the cleaner as shown. For your personal records, please enter the COMPLETE model and serial numberin the spaces provided and retain this information. Your cleaner is model___________________________________ and has serial nu...

Page 3 - Continued; Assembling cleaner; Attach

3 STEP 1 Attach rack and handle Carton contents Remove all parts from carton andidentify each item shown. Makesure all parts are located beforedisposing of packing. A. Handle sectionB. Cleaner bodyC. Hose rackD. Hose, cleaning tools and wandsE. Handle bolts and nuts packet (in bag with owner ’s manu...

Page 4 - STEP II Attach hose; place while tightening each bolt; NOTE: Hose must be connected as shown for all; While holding rack in place, slide

Align end of hose with projections(A) over slots (B) in dirt duct. STEP II Attach hose 1-8 1-11 1-13 1-9 1-10 Place nuts in recessed areas onfront of handle. Hold each nut in place while tightening each bolt securely with a Phillips screw driver. Reposition bag door by fitting tabson bottom of door ...

Page 5 - Cleaner description; STEP III Position tools; Polarized plug

2. How to use Cleaner description 15.Furniture guard: helps prevent cleaner from marking furniture. 16.Nozzle control knob: slide knob to cor rect setting for height of carpet being cleaned. 17.Headlight18.Embedded Dirt FIND-ERTM sensitivity switch 19.‘Dirt FINDER’ display20. Check bag indicator21.S...

Page 6 - Settings; Handle positions; Handle position; HIGH

Carpet heightadjustment The cleaning of carpet and rugs takesplace at the nozzle (A). When it is necessary to raise and lowerthe nozzle for various carpet pileheights, slide the nozzle control knob (B)to the desired setting. 2 - 9 Settings For maximum cleaning performance, the following carpet heigh...

Page 7 - Cleaning tools; Removing hose

7 Cleaning lightweightflexible rugs Stand on one end of rug and movecleaner toward other end or edge.Before reaching edge, push down onhandle. This will lift up the nozzle (frontof cleaner) as shown and will preventrug from clinging to cleaner. Continue tolift up nozzle so that when you havereached ...

Page 8 - Select proper tool; Filter bag; Removing bag door; Check bag indicator

3 - 1 8 2 - 1 6 Attach wand and tools Attach tool or wand to the hose (C). Attach second wand or tool to wand (D)by pushing it firmly onto the wand. Twist wand or tool slightly to tighten orloosen the connection. Where to buy Filter bags may be purchased from yourAuthorized Hoover Dealer (Depot),Lea...

Page 9 - Cleaning final filter; Cleaning secondary filter; Replacing bag door; Reattaching filter door

Cleaning final filter The final filter assists in the filtration process to return clean air to the room. To remove this filter when it becomes dirty, open the door on the side of thecleaner. Lift out filter (B) and hand wash it incold water with mild detergent. Let filter air dry and reposition it ...

Page 10 - Belt replacement; When to replace; How to replace; Headlight replacement; What to buy

Securing agitator Grasp agitator firmly and fit it into posi-tion by first sliding end opposite the beltinto the rectangular slot (F) on side ofcleaner.Pull other side of agitator (G) into place. Turn agitator making sure belt is notpinched between agitator and agitatorshield. A B C D F G E B D 3 - ...

Page 11 - Replacing bottom plate; The agitator brush ro l l; Installing groomers; nect cleaner from electrical outlet.; P o w e red hand tool

How to replace Disconnect cleaner from electricaloutlet. Remove bottom plate, belt and agitatorfollowing directions in “The belt” sectionbeginning with Fig. 3-10. Discard old agitator. Continue following the directions in “Thebelt” section to reposition belt, new agi-tator and bottom plate. 11 Repla...

Page 12 - Powered hand tool; Inspecting the belt; Lubrication; Service

12 7. Replace belt guard (B) making surenot to pinch brush bristles in guard. Tur nagitator making sure it rotates freely.Replace and tighten screws. 8. To replace bottom plate (A), insert thefour tabs on edge of bottom plate into slots on front of tool.Pivot bottom plate down and snapclosed. Powere...

Page 13 - problem; Clearing blockages; Checking under bottom plate

13 If further assistance is needed, contactThe Hoover Company ConsumerResponse Center, North Canton, Ohio44270, Phone: 1-330-499-9499. In Canada, contact Hoover Canada,Burlington, Ontario L7R 4A8,Phone: 1-800-263-6376. Always identify your cleaner by the complete model number when request - ing info...

Hoover WindTunnel Upright Bag Vacuum Cleaner- User Manual

Table of Contents:

Other Manuals for Hoover WindTunnel Upright Bag Vacuum Cleaner

Summary

Other Hoover Models