Hoover SteamVac V2- User Manual

5 1-10 1-9 1 - 1 1 1 - 1 2 1 - 1 3 1 - 1 4 1 - 1 5 1 - 1 6 Storing hose andtools Press hose, a few inches from nozzleconnector end, into caddy. Bring hoseup and over top of caddy. Press hose into opposite side of caddy.Loop hose at bottom of cleaner andpress into top of hook (I). Loop hose over top ...

6 2. How to use The assembled deep cleaner will look like the drawing. Model with SpinScrub™ hand tool is shown. 2-1 2-2 1. Hand grip2. Solution trigger: press to release cleaning solution 3. ON/OFF switch4. Wash/Rinse switch5. SpinScrub™ hand tool (not included with all models) 6. Carrying handle7....

Automatic shut off When the re c o v e ry tank (lower tank) is fullthe automatic shutoff mechanism will shuto ff the deep cleaner suction (suction will be noticeably reduced). At that time, the yellow float disk will riseto the top of the recovery tank lid (B).The deep cleaner will no longer pick up...

8 2-13 2-14 2-15 2-16 Fill container (16 oz.) with HOOVERCarpet/Upholstery Detergent orHOOVER Bare Floor Cleaner.Do not use Bare Floor Cleaner on carpet or u p h o l s t e ry. Do not use any type of wax with your ‘SteamVa c ’deep cleaner. To assure proper results, use only HOOVER detergent. Replace ...

9 Continued ➜ Before you begincleaning a. Vacuum thoroughly - For carpet, use a HOOVER vacuum cleaner with an agitator for best results. Vacuum uphol -stery with a vacuum cleaner with clean-ing tool attachments. Use a crevice toolto reach into tufts and folds. Do not use the ‘SteamVac’ deep cleaner ...

Carpet Cleaning Slide nozzle completely onto cleaner. Press down on nozzle to secure it. Replace recovery tank (Fig. 2-17). The nozzle must be in the properposition in order for the recovery tankto go on properly. Raise cleaner to upright position andreplace clean water tank (Fig. 2-15). 3-6 3-7 Rea...

11 Continued ➜ Cleaning bare floors 3-9 How to attach bare floorattachment (Available at additional cost if not includ-ed with your cleaner.) Unplug deep cleaner from electricaloutlet. To prevent possible leaking, removeclean water tank (Fig. 2-10) and recov- ery tank (Fig. 2-16) before positioningb...

3-20 13 Continued ➜ A B 3-18 Attaching scrub module Available at additional cost if not includ-ed with your cleaner. 1. Open the tool door and remove theSpinScrub™ hand tool. 2. Grasp the sides of the brush moduleand lift it from the base (L). 3. Snap scrub module onto the base. Note: If may be nece...

4-1 4-2 To replace brushes Align posts (A) on both ends of brushassembly with slots (B) in cleaner hous-ing. Make sure that the square post (C) alsoaligns with the square hole (D). Tur nbrushes slightly until post fits easily intohole. Press brush assembly firmly to snap intoplace. 4-3 A A B B C D 3...

15 • checking the Yellow Pages under “Vacuum Cleaners - Household” OR • calling 1-800-944-9200 for an automated referral of authorized service outlet locations (U.S. only). Do not send your cleaner to The Hoover Company in North Canton for service,this will only result in delay. If further assistanc...