Hoover Self-Propelled WindTunnel Bagless with Powered Hand Tool - Manual

Page 2 - ENGLISH; Review this manual before; Important Safeguards!; READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE; Save these instructions!; Index

Fill in and retain The model and serial number are located on the back of the handle as shown. For your personal records, please enter the COMPLETE model and serial numberin the spaces provided and retain this information. Your cleaner is model___________________________________ and has serial numbe...

Page 3 - Assembling cleaner; Carton contents; Continued; Accessories

3 1. Assembling cleaner Carton contents Remove all parts from carton andidentify each item shown. Makesure all parts are located beforedisposing of packing.A. Handle sectionB. Cleaner bodyC. Handle screw packet (in bag with owner’s manual) Note: The white switch lock above the ON/OFF switch aids in ...

Page 4 - NOTE: Hose must be co; Polarized plug; Cleaner description; Transporting cleaner

16. Nozzle control knob: slide knob to correct setting for height of car- pet being cleaned. 17. Brush roll control18. Furniture guard19. Headlight20. Edge groomers21. Hose22. Hose rack23. ‘Dirt FINDER’ display * 24. Embedded ‘Dirt FINDER’ sensitivity switch * 25. Cord hooks: wrap cord around hooks ...

Page 5 - Brush roll control; Handle positions

FLOOR CARPET HARD 2-9 Brush roll control Note: When handle is in uprightposition, brush roll is automaticallyOFF. Move the brush roll control only whenthe handle is in the upright position. Slide control to “Carpet” to turn brushroll ON for cleaning carpet or rugs. Slide control to “Hard” to turn br...

Page 6 - AUTOMATIC; ON

6 Cleaning lightweightflexible rugs Stand on one end of rug and movecleaner toward other end or edge.Before reaching edge, push down onhandle. This will lift up the nozzle (frontof cleaner) as shown and will prevent rugfrom clinging to cleaner. Continue to lift up nozzle so that whenyou have reached...

Page 8 - Filter assembly; How to clean filter

8 3-4 3-5 3-7 3-6 Press down on area indicated (H) toopen dirt cup lid. Empty cup. Note: It is not necessary to remove the HEPA cartridge filter to empty the dirtcup. Filter assembly The HEPA cartridge filter and pre-filterare essentially self-shedding. Turning the knob on the lid as describedin “Ho...

Page 9 - Headlight replacement; What to buy; Final filter; Replacing final filter; Removing lens; Installing bulb; Replacing lens

9 3-14 3-15 3-16 Headlight replacement What to buy This cleaner uses a 12 volt, wedge basetype 912 bulb, Hoover part No. 27313101. Reattaching filter door The filter door is designed with a“break-away” feature which allows it tosnap free if it is pushed open too far. To reattach, align hinges (O) of...

Page 10 - Positioning front of belt; Positioning back of belt; The agitator brush roll; Belt replacement; When to replace; Removing bottom plate

D C A B C Positioning front of belt Place other end of belt over large pulley(C) while rolling the pulley in directionshown. Extra effort may be required to stretch belt onto pulley. Positioning back of belt With lettering on outside of belt, slidenew belt over motor shaft (D). 10 3-20 Replacing bot...

Page 11 - Replacing brush roll; Removing brush roll; Installing brush roll; Powered hand tool; Agitator brush roll; How to replace

11 Inspecting V-belt The V-belt is designed to last for a longtime and is not normally replaced.However, if V-belt is cracked, gouged orbroken, now is a good time to replace itas follows.Slide flat belt off large pulley as shownin Fig. 3-19.To remove V-belt, slide back of belt over pulley (C). Then ...

Page 12 - Replacing belt

Replacing belt When replacing belt, ask for HOOVER part No. 38528037. 1. Remove bottom plate, belt guard andbrush roll as described in Figs. 3-28through 3-30. 3-36 3-35 F E 2. Grasp turbine (E) and pull firmly toremove. 3. Remove belt from turbine pulley (F).Replace with new belt. 4. With flat sides...

Page 13 - Installing groomers; Lubrication; Service

3-37 13 Edge groomer replacement When to replace The edge groomers, located on bothsides of the nozzle, should be replacedwhen they are worn. What to buy When purchasing edge groomers, askfor HOOVER part No. 39511004. How to replace Disconnect cleaner from electrical outlet. Remove bottom plate as d...

Page 14 - Clearing blockages; Disconnect cleaner from electrical

B. If a blockage occurs duringtool use: Turn cleaner OFF and disconnect fromelectrical outlet.1. Look into hose end and remove anyblockage. Note: Electrical parts are enclosed in the cleaner. Do not remove any screws.If blockage cannot be removed throughexisting openings, take the cleaner to aHoover...

Hoover Self-Propelled WindTunnel Bagless with Powered Hand Tool - Manual

Table of Contents:

Summary

Other Hoover Models