Hoover 800- User Manual

The two sections (A & B) of the tool caddy snap together for assembly. Press where indicated by arrows to snap securely in place. The caddy conveniently fits over the top of the cleaner nozzle (C) for storage. 9 10 9 10 Assemble tool caddy A B C C C D E 8 While holding nozzle in place, slide lat...

8 18 The Mode selector dial (A) turns the brush- es on and off. Your HOOVER FloorMate™ SpinScrub™ 800 Cleaner can be used to both vacuum dry debris and wet clean non-carpeted floor surfaces such as vinyl, tile, marble and sealed wood. It is not intended for use on carpet or rugs. CAUTION: To prevent...

9 Pour cleaning concentrate into tank (B). Fill tank to fill line (C) (1 quart) with warm water. B C 23 DO NOT use cleaning concentrates that contain solvent based ingredients. CAUTION: HOOVER® Floor to Floor™ Cleaning Concentrate and HOOVER® Grout Cleaner cannot be used in Hoover SteamVac™ products...

11 30 Reposition filter. Replace filter lid. Press down firmly until snapped in place. The tank lid contains a washable, reusable filter. Clean this pleated filter when suction is low or reduced. Turn cleaner OFF and disconnect from electrical outlet. Remove recovery tank and lid (Figs. 27 & 28)...

Use your HOOVER® FloorMate™ SpinScrub™ 800 Cleaner to: • Dry Vacuum to remove loose dirt, hair and debris. • Wet Clean the floor surface. The brushes will provide light agitation to help loosen dirt. • Wet Pickup reduces drying time of the floor surface. The Mode selector dial turns the brushes on a...

NOTE: Your HOOVER® FloorMate™ SpinScrub™ 800 cleaner may be used to clean wood floors that have been sealed with a polyurethane coating and can be cleaned with water. CAUTION: To prevent damage to wood floors, follow the flooring manufacturer’s cleaning rec-ommendations. If using cleaner on sealed w...

14 Select tool Attach hose and tool A B A. Floor swivel tool • Swivel head • 2 rows of brushes • Use to clean small, tight areas B. Grout tool • Stiff brushes to use for more concentrated cleaning on stubborn grout stains Unplug cleaner from electrical outlet. How to connect hose ✓ Open hose door (A...

Before storing cleaner: Turn cleaner OFF and disconnect from electrical outlet. • Empty and rinse solution and recovery tanks. Allow to air dry. • Press on upper handle release button to lower handle for storage. • Make sure that nothing is pressing on the nozzle squeegee. • Do not store cleaner on ...

16 Maintenance Cleaning the nozzle Turn cleaner OFF and disconnect from electrical outlet. The cleaner ’s nozzle can be removed for easy cleaning. Slide the two nozzle release latches (A) outward. Remove nozzle (B) by pulling straight out. Rinse nozzle under running water. Remove debris from squeege...

48 49 50 51 Cleaning the brushes The brush assembly can be removed for easy cleaning. Turn cleaner OFF and disconnect from electrical outlet. Place handle in the upright position. Remove tanks to prevent leaking. Set aside. Pull the two nozzle release buttons (A) out. Remove nozzle. Tilt cleaner bac...

Troubleshooting What’s the problem? What to do Cleaner won’t run ✓ Make sure the cleaner is plugged in firmly. ✓ Check the fuse or breaker. Low suction ✓ Empty the recovery tank; it may be full and the automatic shut-off engaged. ✓ Make sure filter and filter lid are properly positioned. ✓ Make sure...

19 To obtain approved HOOVER service and genuine HOOVER parts, locate the nearest HooverFactory Service Center or Authorized Hoover Warranty Service Dealer (Depot) by: ✓ Checking the Service Section of The Hoover Company on-line at www.hoover.com OR ✓ Checking the list of Factory Service Centers pro...