Page 2 - Technical Data
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN EN1B-0198GE51 R0801 H o ne y w e ll BNA - 2DN Reset Mode Power Rx Rx Tx Tx Col Rx Tx Lnk LAN Ch1 Ch2 H oneyw e ll BN A - 2 DN Reset Mod e Power Rx Rx Tx Tx Col Rx Tx Lnk LAN Ch1 Ch2 1 2 6 7 3 4 5 Figure 1-1: Parts and Controls on the Front Side 8 9 10 11 12 13...
Page 3 - Table of Contents
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN EN1B-0198GE51 R0801 Table of Contents 1 About BNA ........................................................... 5 2 Location of Parts and Controls .......................... 8 2.1 Front Side .................................................... 8 2.2 Rear Side .....
Page 7 - T connectors plus a RS232
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN EN1B-0198GE51 R0801 7 Additionally, each BNA type is equipped with AUIand RJ45 10Base T connectors plus a RS232 interface.
Page 8 - Location of Parts and Controls; Side; Reset; on
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN 8 EN1B-0198GE51 R0801 2 Location of Parts and Controls The numbering for the parts and controls in thissection is referring to the pictures on the rear side ofthe title page. In order to have a reference betweenthe numbering here and the device pictures, it is...
Page 9 - Shows the actual LAN traffic using 4 LEDs.; Col; Collision indicator; Red; Receive indicator
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN EN1B-0198GE51 R0801 9 Shows the actual LAN traffic using 4 LEDs. Col Collision indicator ( Red ) If this LED is on, then two or moredevices on the network aretransmitting at the same time. This isnot a fault, but a normal occurrenceon an Ethernet network. Howe...
Page 11 - -pin connector for field bus channel
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN EN1B-0198GE51 R0801 11 2.2 Rear Side Differences between the various BNA types areexplicitly noted in the corresponding elementdescription. 8 Ch2 3-pin connector for field bus channel 2 connection electrically isolated meets theEMC-and FCC-requirements. Field ...
Page 13 - Pieces
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN EN1B-0198GE51 R0801 13 3 Before Installation Please pay attention to the steps listed below priorto installing the Building Network Adapter device. 1 Verify that the product has been received without damage. 2 Verify that the correct BNA type has been delivere...
Page 14 - Optional wall mounting clips; Do not remove the cover of a BNA device.
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN 14 EN1B-0198GE51 R0801 Pieces Item 2 3 pole Phoenix controller buschannel connectors 4 Optional wall mounting clips 4 Small inserts 4 Screws 4 Please read chapter 5 Connections on page 19 carefully prior to connecting any power anddata interface cables to the ...
Page 15 - BNA Operating Positions; Device; shows the normal BNA device operating
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN EN1B-0198GE51 R0801 15 4 BNA Operating Positions 4.1 Single Device Figure 4-1: Single device operating position Figure 4-1 shows the normal BNA device operating position e.g. on a desk.
Page 19 - Connections; Connection
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN EN1B-0198GE51 R0801 19 5 Connections This chapter describes how to connect power andthe field bus to the BNA device. Together with the BNA device, a supply pack withinstallation material is delivered containing therequired connectors for power and field bus. 5...
Page 20 - shows the pin layout of the field bus; Termination
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN 20 EN1B-0198GE51 R0801 5.2 Field Bus Connection (Ch1 / Ch2) Regardless of the type of BNA device, the wiring ofthe field bus connector is always identical. For connecting the field bus, the 3 pole Phoenixconnectors (included) are required. AC +1 BC -2 GND Figu...
Page 21 - normal
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN EN1B-0198GE51 R0801 21 For each channel the required termination settingcan be adjusted individually. At the rear side of the device, a pictogram ( Figure 5-2 ) symbolizes the different possible bus terminations. Figure 5-2 normal XD505 compatible bus terminat...
Page 22 - This section applies to BNA 2DN devices only.
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN 22 EN1B-0198GE51 R0801 XD508 compatible; bus terminationenabled XD508 compatible switch position forC-Busses equipped only with XL500family controllers with bus terminationenabled. This switch position must beused if the BNA device is installed atthe end of su...
Page 23 - Bootloader; BNA Devices are not equipped with any; Behavior; RED; flashing
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN EN1B-0198GE51 R0801 23 6 BNA Bootloader This chapter describes the functions of the BNABootloader software. Each BNA device is equippedwith a Bootloader, which functions in the same wayfor all BNA device types. N o t e : BNA Devices are not equipped with any a...
Page 25 - Modes; Normal Mode; Switching the Operating Mode; Press the Reset Button
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN EN1B-0198GE51 R0801 25 6.2 Operating Modes The BNA Bootloader provides two differentoperating modes: • Normal Mode (default) • Stay in Bootloader Mode Normal Mode is the default, which directly starts an application firmware found in Flash memory. If nofirmwar...
Page 28 - Setup; An active FTP-Server machine on the LAN
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN 28 EN1B-0198GE51 R0801 6.4 Device Setup In order to setup the BNA device properly, thefollowing connections are necessary: • DB9F Null-Modem cable connected to a PCrunning a VT100 terminal emulation program or a VT100 compatible terminal (refer to Table 6-1: T...
Page 29 - np
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN EN1B-0198GE51 R0801 29 If this is the very first run of the device, then theCopyright notice is followed by the query for the root user password. At the Old password: prompt just hit the Enter-Key. Once a password has been defined the BNA printsthe information...
Page 30 - dc
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN 30 EN1B-0198GE51 R0801 C A U T I O N : Using not-allowed IP-Addresses could cause interference on the network. Please contact your network administrator toretrieve a unique IP-Address. In case you want to connect the BNA to a customer network make sure to get ...
Page 31 - um; Description; help
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN EN1B-0198GE51 R0801 31 As mentioned above, the three commands are theminimum required commands for setting up aBNA device. We recommend also performing someuser definitions (see command um ) for different user roles. Doing so prevents unfamiliar users fromperf...
Page 32 - Text; All BNA Bootloader commands are case-; Help; - Basic network parameters
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN 32 EN1B-0198GE51 R0801 Text Text written with this font showsterminal output. N o t e : All BNA Bootloader commands are case- sensitive! 6.5.1 Help or ? Entering help or ? at the BNA bootloader> prompt followed by <Enter> displays all available BNA Bo...
Page 33 - - Download configuration; The download configuration command
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN EN1B-0198GE51 R0801 33 individually. After having entered allrequested information, it will be askedwhether to take over the new settings.If this is denied the old settings will berestored. Otherwise, the new settingsare stored to the Flash memory and thesyste...
Page 35 - With some Windows NT
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN EN1B-0198GE51 R0801 35 individually. After having entered allrequested information it will be askedwhether to take over the new settings.If this is denied the old settings will berestored. Otherwise, the new settingsare stored to the Flash memory. Thesesetting...
Page 36 - the parameters may be wrong is; load
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN 36 EN1B-0198GE51 R0801 the parameters may be wrong is acceptable. exit exits the sub-shell and returns to themain shell. 6.5.4 load - Load executable The command load is a direct command which immediately starts downloading the applicationfirmware image into t...
Page 37 - - Show installed software; ver; - Execute installed software; run
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN EN1B-0198GE51 R0801 37 6.5.5 ping - ping Sends an ICMP Ping through TCP/IP to the FTP-Server defined in the download configuration or tothe machine addressed by the IP-Address in theoptional command-line parameter. This command can be used to check whether the...
Page 39 - Administrative users.
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN EN1B-0198GE51 R0801 39 user View only rights. Users who are member of this groupare not allowed to change or deleteany existing definition. priv Privileged rights. Users of the privileged group areallowed to change several definitionslike network parameters bu...
Page 40 - - Login as different user; root user
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN 40 EN1B-0198GE51 R0801 delete deletes existing user. The username canoptionally be passed directly on thecommand-line. Furthermore an option –all is available that deletes all user definitions except the one for the root user . The root user account can’t be d...
Page 42 - Cables and Connectors; DB9F Null Modem Cable
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN 42 EN1B-0198GE51 R0801 7 Cables and Connectors 7.1 DB9F Null Modem Cable Figure 7-1: Serial connectors The female connector is numbered as shown below: 1 DCD 2 RxD 3 TxD 4 DTR 5 Ground 6 DSR 7 RTS 8 CTS 9 RI
Page 43 - shows how to configure a Null Modem
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN EN1B-0198GE51 R0801 43 Figure 7-2 shows how to configure a Null Modem Cable DB9F. 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 DCD RxD TxD DSR DTR GND RTS CTS 9 9 RI DCD RxD TxD DSR DTR GND RTS CTS RI Figure 7-2: Signal connections for DB9F Null Modem Cable
Page 44 - Connectors; Connector
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN 44 EN1B-0198GE51 R0801 7.2 Ethernet Connectors Figure 7-3: BNA Ethernet connectors The BNA provides two different types ofconnectors to bring the device online on the LAN.First is a RJ45 10BaseT connector and second is anAUI connector. This chapter describes t...
Page 45 - Pin Number Signal Name; Reserved
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN EN1B-0198GE51 R0801 45 piece of equipment on the network is connected toa central hub. The wiring is connected to devicesusing a plug that resembles a phone jack, calledRJ45. Pin Number Signal Name 1 Transmit (TX) + 2 Transmit (TX) - 3 Receive (RCV) + 4 Reserv...
Page 46 - shows how the different signals need to
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN 46 EN1B-0198GE51 R0801 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 Tx+ Tx- Rx + Rx - Tx+ Tx- Rx + Rx - Figure 7-4: Straight through pinning for BNA to Ethernet Hub connections 7.2.1.2 Connecting a BNA to a Workstation When a BNA should be directly connected to aworkstatio...
Page 47 - Attachment Unit Interface
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN EN1B-0198GE51 R0801 47 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 Tx+ Tx- Rx + Rx - Tx+ Tx- Rx + Rx - Figure 7-5: Crossover pinning for BNA to workstation direct- connections 7.2.2 AUI Connector The AUI ( Attachment Unit Interface ) offers an alternative way of connectin...
Page 48 - Receive shield
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN 48 EN1B-0198GE51 R0801 Nowadays the AUI is used to connect a smalldevice called transceiver, which adapts between theAUI on the device and the Ethernet medium usedin the current installation. 1 8 9 15 AUI Interface Specification male connector 1. Coll. shield ...
Page 50 - FAQs; Which terminal type can be used for; Startup Behavior
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN 50 EN1B-0198GE51 R0801 FAQs 1. Which terminal type can be used for connecting to the BNA Bootloader? For connecting to the BNA Bootloader, anyVT100 compatible terminal or VT100compatible terminal emulation program can beused. For the proper terminal settings, ...
Page 51 - Glossary
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN EN1B-0198GE51 R0801 51 Glossary 10BaseT 10 = 10Mbps,Base = baseband,T = twisted pair. Application firmware An application firmware is a softwarethat is needed to operate the BNAdevice in a way the BuildingManagement System requires it. Anexample for an applica...
Page 52 - TCP; Transmission Control Protocol; WAN; Wide Area Network; XLCL; EXCEL Classic
BUILDING NETWORK ADAPTER BNA-1C/2CS/2DN 52 EN1B-0198GE51 R0801 TCP Transmission Control Protocol WAN Wide Area Network XD505 C-Bus piggyback type of XL500controllers.Compatible with EXCEL IRC deviceson the same bus. XD508 C-Bus piggyback type of XL500controllers. This piggyback type allowsC-Bus comm...
