Honeywell MicroDock II- Manual

Page 2 - Limited Warranty and Limitation Liability; Contacting BW Technologies by Honeywell

Limited Warranty and Limitation Liability BW Technologies LP (BW) warrants the product to be free from defects in material and workmanship under normal use and service for a period of two years, beginning on the date of shipment to the buyer. This warranty extends only to the sale of new and unused ...

Page 3 - MicroDock II; Introduction; Warning; Safety Information - Read; Safety Information - Read First; BW Technologies by Honeywell; Cautions

1 MicroDock II Introduction a Warning To ensure personal safety, read Safety Information - Read First before using the MicroDock II base station. The MicroDock II Automatic Test and Calibration Station (“the base station”) provides automated calibration and bump testing for the GasAlert Extreme, Gas...

Page 4 - Display Elements

MicroDock II Quick Reference Guide 2 Display Elements Pushbuttons Item Function AC power Batteries fully charged Batteries half-charged Batteries at low level MultiMediaCard (MMC) MultiMediaCard (MMC) not inserted Test pass and option enabled Test fail and option disabled Cursor and sensor disabledS...

Page 5 - User Options Menu

3 MicroDock II User Options Menu User Options Menu Description Display Time/Date modifies the time and date of the base station. Inlet Setup enters the gas type, the gas concentration levels, and the gas cylinder lot numbers. Pump Setup modifies the station pump speed. Recommended pump speeds are 40...

Page 6 - Installation; Item

MicroDock II Quick Reference Guide 4 Installation Item Description 1 Inlet filter assembly 2 C-cell batteries (4) 3 Battery cover 4 Philips pan head retaining screws (2) 5 MultiMediaCard (MMC) 6 Battery compartment 7 Charger port 8 USB port 9 Power port 10 Exhaust outlet 11 Gas cylinder 12 Demand fl...

Page 7 - Battery Installation

5 MicroDock II Installation a Warning The atmosphere must be free of background gas. Do not use the base station in a hazardous area.All required National Electrical Codes (NEC) and safety standards must be followed. Note The base station can operate from either an electrical power source or batteri...

Page 8 - Inserting the Detector; Caution; GasAlertClip Extreme / GasAlert Extreme

MicroDock II Quick Reference Guide 6 Inserting the Detector a Caution Infrared or intense ambient light (sun or halogen) may interfere with the base station/detector communication. To insert a detector into a docking module, complete the follow-ing: 1. Activate the detector and wait until it is in n...

Page 9 - GasAlertMicroClip; Using the Base Station

7 MicroDock II Using the Base Station • When the detector has been inserted correctly, the RUN LEDs light yellow, Unit Inserted displays on the base station LCD, and MicroDock displays on the detector LCD. The base station LCD displays the docking mod-ule number, and the type and serial number of th...

Page 10 - Activating the Station; menu

MicroDock II Quick Reference Guide 8 The base station pushbuttons are not labelled. The base station is operated by pressing the C pushbutton that is located directly below the option that displays on the LCD. Activating the Station 1. To activate the station, press and hold C (the left- most button...

Page 11 - exit; Bump Test; OK; Calibration

9 MicroDock II Bump Test 5. Press C exit to return to normal operation. For more information on setting up inlets, gas types, and con-centration levels, refer to Inlet Setup in the MicroDock II Base Station User Manual . Bump Test A bump test is performed to confirm that the detector is responding t...

Page 12 - Purge; Data Transfer

MicroDock II Quick Reference Guide 10 A calibration adjusts the sensor sensitivity to ensure an accu-rate response to gas. To calibrate a detector, complete the following: 1. From the docking module of the applicable detector, press C CALIBRATION. 2. The gas is automatically applied. 3. When the cal...

Page 13 - Successful Data Transfer:; Maximum Storage Capacity; Automatic Datalog Download; Eventlogging; Access Test Results; Configuring the Detector

11 MicroDock II Automatic Datalog Download (GasAlertMicroClip and GasAlertMax XT docking module only) Successful Data Transfer: The PASS LED lights green on the docking module and Pass displays on the base station LCD. From the LCD, press C Pass to return to normal operation. Unsuccessful Data Trans...

Page 14 - Charging the Battery Pack; The charger is for indoor use only.

MicroDock II Quick Reference Guide 12 • GasAlertMicroClip• GasAlertMax XT The detector can be configured prior to performing a bump test or calibration to • change user options, • sensor options, and • program options. The detector can also be configured to disallow bump tests or calibrations unless...

Page 15 - Maintenance

13 MicroDock II Maintenance 4. Allow the battery to obtain a full charge (2 to 4 hours, depending upon how many docking modules are con-nected to this station). If a docking module is in queue waiting to charge, the CHARGE LED flashes red (all charging modules). When the docking module begins chargi...

Page 16 - Specifications

MicroDock II Quick Reference Guide 14 Specifications The MicroDock II base station and docking modules are for indoor use only. Instrument dimensions: (w x l x h) 21.2 x 26.3 x 8.2 cm (8.3 x 10.4 x 3.2 in.) base station and one docking module Weight: 0.98 kg (2.15 lb.) Base system ingress protection...

Page 17 - Charger Specifications; Charger system ingress protection:; Installation Category:

15 MicroDock II Charger Specifications Charger Specifications Size: 8.6 x 8.2 x 7.8 cm (3.4 x 3.2 x 3.1 in.) Weight: 97 g (3.4 oz.) per model Charger system ingress protection: IP20 Operating temperature: 10°C to 35°C (50°F to 95°F) Humidity: 0 to 50% Altitude: 2000 m (6561.66 ft.) Power: 6 Vdc , 2....

Page 19 - Quick Reference Guide; Automatic Test and Calibration Station

Honeywell MicroDock II- Manual

Table of Contents:

Other Manuals for Honeywell MicroDock II

Summary

Other Honeywell Models