Honeywell CCB00 010BT - User Manual

iii Voyager 1202g Battery Removal......................................................................................... 3-3 Charging Information ..................................................................................................... 3-3Battery Recommendations ..........................

iv Chapter 4 - Cordless System Operation (Voyager 1202g-BF) How the Charge and Communications Base Works ........................................................... 4-1Linking the Scanner to a Base............................................................................................. 4-1Commun...

v Good Read and Error Indicators.......................................................................................... 5-1 Beeper – Good Read ..................................................................................................... 5-1Beeper Volume – Good Read...........................

vi Prefix Selections .................................................................................................................. 6-2Suffix Selections .................................................................................................................. 6-2Transmit Alternate Extend...

vii UPC-E0 ............................................................................................................................. 8-30EAN/JAN-13 ...................................................................................................................... 8-33 Convert UPC-A to EAN-13 ...

viii Chapter 12 - Maintenance and Troubleshooting Repairs .............................................................................................................................. 12-1Maintenance ......................................................................................................

iii Customer Support Technical Assistance To search our knowledge base for a solution or to log in to the Technical Support portal and report a problem, go to www.hsmcontactsupport.com . For our latest contact information, see www.honeywellaidc.com/locations . Product Service and Repair Honeywell In...

1 - 1 1 Getting Started About This Manual This User’s Guide provides installation and programming instructions for the Voyager 1200g/1202g/1202g-BF linear scanner. Product specifications, dimensions, warranty, and customer support information are also included. Honeywell bar code scanners are factor...

1 - 2 1. Connect the appropriate interface cable to the scanner first, then to the computer. 2. Make sure the cables are secured in the wireways in the bottom of the base and that the base sits flat on a horizontal surface. 3. The scanner beeps. 4. Verify the scanner or base operation by scanning a ...

1 - 4 Connecting with RS232 Serial Port 1. Turn off power to the terminal/computer. 2. Connect the appropriate interface cable to the scanner. Note: For the scanner or base to work properly, you must have the correct cable for your type of terminal/computer. 3. Make sure the cables are secured in th...

1 - 5 Connecting with RS485 A scanner or base can be connected for an IBM POS terminal interface. 1. Connect the appropriate interface cable to the device, then to the computer. 2. Make sure the cables are secured in the wireways in the bottom of the base and that the base sits flat on a horizontal ...

1 - 6 Reading Techniques The scanner has a view finder that projects a bright red aiming beam that corresponds to the scanner’s horizontal field of view. The aiming beam should be centered horizontally over the bar code and must highlight all the vertical bars of the bar code. It will not read if th...

1 - 7 Resetting the Custom Defaults If you want the custom default settings restored to your scanner, scan the Activate Custom Defaults bar code below. This resets the scanner to the custom default settings. If there are no custom defaults, it will reset the scanner to the factory default settings. ...

2 - 1 2 Programming the Interface Introduction This chapter describes how to program your system for the desired interface. Programming the Interface - Plug and Play Plug and Play bar codes provide instant scanner set up for commonly used interfaces. Note: After you scan one of the codes, power cycl...

2 - 2 RS485 Scan one of the following “Plug and Play” codes to program the scanner for an IBM POS terminal interface. Note: After scanning one of these codes, you must power cycle the cash register. Each bar code above also programs the following suffixes for each symbology: * Suffixes programmed fo...

2 - 3 USB IBM SurePos Scan one of the following “Plug and Play” codes to program the scanner for an IBM SurePos (USB handheld scanner) or IBM SurePos (USB tabletop scanner) interface. Note: After scanning one of these codes, you must power cycle the cash register. Each bar code above also programs t...

2 - 4 USB PC or Macintosh Keyboard Scan one of the following codes to program the scanner for USB PC Keyboard or USB Macintosh Keyboard. Scanning these codes also adds a CR and LF for Voyager 1200g and adds CR for Voyager 1202g and 1202g-BF. USB HID Scan the following code to program the scanner for...

2 - 5 USB Serial Commands USB Serial Scan one of the following codes to program the scanner to emulate a regular RS232-based COM Port. If you are using a Microsoft® Windows® PC, you will need to download the USB serial driver from the Honeywell website (www.honeywellaidc.com) . The driver will use t...

2 - 6 ACK/NAK Mode Communication Timeout This allows you to set the length (in milliseconds) for a timeout for the host ACK/NAK response. Scan the bar code below, then set the timeout (from 0-65535 milliseconds) by scanning digits from the Programming Chart , then scanning Save . Default = 2000 ms. ...

2 - 7 Support BEL/CAN in ACK/NAK This protocol responds to <BEL> and <CAN> commands when in ACK/NAK mode. The scanner sounds an error tone when a <BEL> command is sent from the host. <CAN> terminates the transmission. Default = BEL/CAN Off . Verifone ® Ruby Terminal Default S...

2 - 8 Gilbarco ® Terminal Default Settings Scan the following Plug and Play code to program the scanner for a Gilbarco terminal. This bar code sets the baud rate to 2400 bps and the data format to 7 data bits, even parity, 2 stop bits. It also adds a carriage return (CR) suffix and programs the foll...

2 - 9 NCR Bioptic Aux Port Configuration Scan the following Plug and Play code to program the scanner for an NCR bioptic scanner auxiliary port configuration. This bar code sets the baud rate to 9600 bps and the data format to 7 data bits, Even parity, 1 stop bit and Message RTS/CTS with time-out. T...

2 - 10 Wincor Nixdorf Beetle™ Terminal Default Settings Scan the following Plug and Play code to program the scanner for a Wincor Nixdorf Beetle terminal. The following prefixes are programmed for each symbology: Note: If you are having unexpected results with this programming code, scan the Resetti...

2 - 11 By default, national character replacements are used for the following characters: #$@[\]^‘{|}~ Refer to the ISO 2022/ISO 646 Character Replacements on page A-7 chart to view the character replacements for each country. Keyboard Countries * United States Albania Arabic Azeri (Cyrillic) Azeri ...

2 - 19 Keyboard Wedge Modifiers ALT Mode If your bar code contains special characters from the extended ASCII chart, for example, an e with an accent grave (è), you will use ALT Mode. (See "Extended ASCII Characters" on page A-4.) Note: Scan the ALT mode bar code after scanning the appropria...

2 - 20 Autocaps via NumLock bar code should be scanned in countries (e.g., Germany, France) where the Caps Lock key can- not be used to toggle Caps Lock. The NumLock option works similarly to the regular Autocaps, but uses the NumLock key to retrieve the current state of the Caps Lock. Emulate Exter...

2 - 21 Default = Control + X Mode Off. Numeric Keypad Mode: Sends numeric characters as if entered from a numeric keypad. Default = Off. Inter-Scan Code Delay When your keyboard detects that any key is being pressed, released, or held down, the keyboard sends a packet of infor-mation known as a “sca...

2 - 22 <F0> Break Character When your keyboard detects that any key is being pressed, released, or held down, the keyboard sends a packet of infor-mation known as a “scan code” to your computer. There are two different types of scan codes: “make codes” and “break codes.” A make code is sent wh...

2 - 24 RS232 Word Length: Data Bits, Stop Bits, and Parity Data Bits sets the word length at 7 or 8 bits of data per character. If an application requires only ASCII Hex characters 0 through 7F decimal (text, digits, and punctuation), select 7 data bits. For applications that require use of the full...

2 - 25 RS232 Handshaking RS232 Handshaking allows control of data transmission from the scanner using software commands from the host device. RTS/CTS Off: RTS/CTS is turned off so no data flow control is used, but RTS is still active. RTS/CTS Off, RTS Inactive: RTS/CTS is turned off so no data flow ...

2 - 26 RS232 Timeout When using Flow Control with Timeout, you must program the length of the delay you want to wait for CTS from the host. Set the length (in milliseconds) for a timeout by scanning the bar code below, then setting the timeout (from 1-65535 milli-seconds) by scanning digits from the...

2 - 28 NAK Retries This selection limits the number of NAK retries that can occur in ACK/NAK mode. Scan the bar code below, then set the number of retries (from 0-255) by scanning digits from the Programming Chart , then scanning Save . (5 is the recom- mended setting.) Default = 0, or disabled. Sup...

2 - 29 Block Check Character When this selection is set to Transmit , the NCR Block Check Character (BCC) is expected with incoming messages and transmitted with outgoing messages. Default = Transmit. NCR Prefix This selection allows you to program an NCR-specific prefix. Refer to the ASCII Conversi...

2 - 30 NCR NOF (Not-on-File) Error A scanner receives an NOF (Not on File) command from the POS whenever it cannot cross-reference the bar code to a price parameter. When set to On , the error tone sounds (set via Number of Beeps – Error , page 5-3) for an NOF, and dis- ables the scanner while the c...

3 - 1 3 Cordless System Operation (Voyager 1202g) Note: This chapter applies only to Voyager 1202g cordless scanning systems. It does not apply to corded or Voyager 1202g- BF scanners. See Cordless System Operation (Voyager 1202g-BF) on page 4-1 for Voyager 1202g-BF scanners (PN: 1202G-BF). How the ...

3 - 2 When data is scanned, the data is sent to the host system via the base. The cordless scanner recognizes data acknowledge-ment (ACK) from the base. If it cannot be determined that the data has been properly sent to the base, the scanner issues an error indication. You must then check to see if ...

3 - 3 You will not hear a communication error tone in this mode, but you will hear a short buzz when you press the button if the radio communication is not working. Once the radio connection is made, the scanner produces a series of beeps while the data is being transferred to the base. Page Button ...

3 - 4 Place the scanner in the base that is connected to an appropriate power supply. Use only a Listed Limited Power Source (LPS) or Class 2 type power supply with output rated 5 to 5.2Vdc, 1A. Note: If you are powering the base through the interface cable (for example, a USB cable) and not using a...

3 - 6 Reset Scanner Scanning this bar code reboots the scanner and causes it to relink with the base. Scanning While in Base Cradle If you want to be able to scan bar codes while the scanner is in the base, scan the following Scanning in Cradle On bar code. If you want to only allow scanning when th...

3 - 7 Paging Paging Mode By default, the paging button on the base pages the scanner associated with that base. If you want the paging button on your base to be disabled, scan the following Paging Mode Off bar code. When Paging Mode is off, the base will no longer page the scanner when the button is...

3 - 8 Base Address Scan the following bar code to determine the address of the base you are using. Scanner Modes The Voyager is capable of working with Bluetooth devices other than the CCB00-010BT base. Charge Only Mode There may be times when you want to charge your scanner, but not link to the bas...

3 - 9 Open Link Mode - Single Scanner When newly shipped or defaulted to factory settings, a scanner is not linked to a base. A link is established when the scanner is placed into a base. When in Open Link Mode, a new link is established when a new scanner is placed in the base. Each time a scanner ...

3 - 10 Alarm Duration To set the the length of time you want the Out-of-Range alarm to sound, scan the following bar code and then set the time-out duration (from 0-3000 seconds) by scanning digits on the Programming Chart inside the back cover, then scanning Save . Default = 1 sec. Scanner Power Ti...

3 - 11 Batch Mode Batch mode is used to store bar code data when a scanner is out of range of its base, or when performing inventory. The data is transmitted to the base once the scanner is back in range or when the records are manually transmitted. Note: Batch Mode is only supported by the Honeywel...

3 - 12 Batch Mode Quantity When in Inventory Batch Mode (page 3-11), you may wish to transmit the number of multiple bar codes scanned, rather than a single bar code multiple times. For example, if you scan three bar codes called XYZ with Batch Mode Quantity Off , when you transmit your data it will...

3 - 13 Delete Last Code If you want to delete the last bar code scanned when in Batch Mode, scan Delete Last Code . Record Counter If you wish to add a record counter to each bar code scanned in Batch Mode, scan Record Counter On . Your batch output would add a sequential number before each bar code...

3 - 14 Default = Record Counter Off. Total Records If you wish to output the total number of bar codes scanned when in Batch Mode, scan Total Records . Batch Mode Output Order When batch data is transmitted, select whether you want that data sent as FIFO (first-in first-out), or LIFO (last-in first-...

3 - 15 Clear All Codes If you want to clear the scanner’s buffer of all data accumulated in Batch Mode, scan Clear All Codes . Transmit Records Automatically If you are operating in Inventory Batch Mode (see Inventory Batch Mode on page 3-11), you can transmit all stored data to the host system when...

3 - 16 Scanner Name You may assign a name to each scanner you are using for identification purposes. The default name is “Voyager.” Perform the rename operation using either the bar codes on page 3-17 , or by sending the serial command :*:BT_NAM name . where name is the new name for the scanner. To ...

3 - 17 You may also scan the following Scanner Name bar code and scan up to 30 numbers and/or letters for the scanner name. For example, if you wanted to name the linked scanner “312,” you would scan the following bar code, scan the 3 , 1 , and 2 bar codes on the Programming Chart inside the back co...

3 - 18 The following table shows the results of the Auto Reconnect On and Off settings: Maximum Link Attempts The Maximum Link Attempts setting controls the number of times the scanner tries to form a connection with a base. During the connection setup process, the scanner transmits in order to sear...

3 - 19 When the scanner goes out of range, 15 attempts are made to link to the base unit. Each attempt consists of approximately 5 seconds of active time followed by 3 seconds of idle time. After 15 cycles (8*15 =120), or about 2 minutes, the scanner stops trying to connect to the base, but retains ...

4 - 1 4 Cordless System Operation (Voyager 1202g-BF) Note: This chapter applies only to Voyager 1202g-BF cordless scanning systems (PN: 1202G-BF). It does not apply to corded or Voyager 1202g scanners. See Cordless System Operation (Voyager 1202g) on page 3-1 for Voyager 1202g scanners. How the Char...

4 - 2 When data is scanned, the data is sent to the host system via the base. The cordless scanner recognizes data acknowledge-ment (ACK) from the base. If it cannot be determined that the data has been properly sent to the base, the scanner issues an error indication. You must then check to see if ...

4 - 3 Page Button When you press the Page button on the base, the scanner associated with that base will begin beeping (3 short and 1 long beep). If you press the button on a scanner that is beeping in response, or press the Page button on the base a second time, the scanner will stop beeping. See P...

4 - 7 Locked Link Mode - Single Scanner If you link a scanner to a base using the Locked Link Mode, other scanners are blocked from being linked if they are inadvertently placed into the base. If you do place a different scanner into a base, it will charge the scanner, but the scanner will not be li...

4 - 8 The sounds are as follows: Alarm Duration To set the length of time you want the Out-of-Range alarm to sound, scan the following bar code and then set the time-out duration (from 0-3000 seconds) by scanning digits on the Programming Chart inside the back cover, then scanning Save . Default = 1...

4 - 9 The following table shows the results of the Auto Reconnect On and Off settings: Maximum Link Attempts The Maximum Link Attempts setting controls the number of times the scanner tries to form a connection with a base. During the connection setup process, the scanner transmits in order to searc...

5 - 1 5 Input/Output Settings Power Up Beeper The scanner can be programmed to beep when it’s powered up. Scan the Off bar code(s) if you don’t want a power up beep. Default = Power Up Beeper On - Scanner. Note: The Voyager 1202g-BF does not issue a power up beep when the scanner is in the base. Bee...

5 - 3 Beeper Pitch – Error The beeper pitch codes modify the pitch (frequency) of the sound the scanner emits when there is a bad read or error. Default = Razz. Beeper Duration – Good Read The beeper duration codes modify the length of the beep the scanner emits on a good read. Default = Normal. Num...

5 - 4 To change the number of error beeps, scan the following bar code and then scan a digit (1-9) bar code and the Save bar code on the Programming Chart inside the back cover of this manual. Default = 1. LED Indicators The green and red LEDs can be programmed to be On or Off and at different brigh...

5 - 5 LED Brightness Default = Red High, Green High. Note: For Voyager 1202g-BF, all LED Brightness settings result in High brightness. Green LED On when CodeGate Disabled Red LED On when In-Stand Green LED On when In-Stand Red LED On with CTS Green LED On with CTS Red LED On when Battery is Low Gre...

5 - 6 In-Stand and Out-Of-Stand Settings The following settings program the scanner’s behavior when it is either in the stand, or out of the stand (hand-held). Caution: When working with In-Stand and Out-of-Stand settings, enable the settings you want before disabling those you do not want to use. I...

5 - 7 Presentation Mode with CodeGate Out-of-Stand: When the scanner is not in the stand, it automatically detects bar codes and decodes them. However, the data is not transmitted until you press the button. The laser remains on briefly after the transmission. (If you are accustomed to a Voyager 954...

5 - 8 Manual Activation Laser Timeout - Button Settings You can set a timeout for the length of time the laser remains on and attempting to decode bar codes when the button is held down, and after it is released. Set the length (in milliseconds) for a timeout by scanning one of the following bar cod...

5 - 9 CodeGate When CodeGate is On , the button is used to allow decoded data to be transmitted to the host system. The scanner remains on, scanning and decoding bar codes, but the bar code data is not transmitted until the button is pressed. When CodeGate is Off , bar code data is transmitted when ...

5 - 10 End Object Detection After Good Read After a bar code is successfully detected and read from the scanner, the laser can be programmed either to remain on and scanning, or to turn off. When End Object Detection After Good Read is enabled, the laser turns off and stops scanning after a good rea...

5 - 11 Object Detection Laser Timeout You can set a timeout for the length of time the laser remains on and attempting to decode bar codes after an object is detected. Set the length (in milliseconds) for a timeout by scanning the following bar code, then setting the timeout (from 1-65535 millisecon...

5 - 12 Activation Character This sets the character used to trigger scanning when using Character Activation Mode. On the ASCII Conversion Chart (Code Page 1252) , page A-2, find the hex value that represents the character you want to use to trigger scanning. Scan the following bar code, then use th...

5 - 13 Deactivation Character This sets the character used to terminate scanning when using Character Deactivation Mode. On the ASCII Conversion Chart (Code Page 1252) , page A-2, find the hex value that represents the character you want to use to terminate scanning. Scan the following bar code, the...

5 - 14 Output Sequence Overview Output Sequence Editor This programming selection allows you to program the scanner to output data (when scanning more than one symbol) in whatever order your application requires, regardless of the order in which the bar codes are scanned. Reading the Default Sequenc...

5 - 16 Output Sequence Editor Sequence Timeout You may wish to set the maximum time between bar code scans in an output sequence. If that maximum time is not met, the output sequence operation is terminated. Set the length (in milliseconds) for a timeout by scanning the following bar code, then sett...

5 - 17 Require Output Sequence When an output sequence is Required , all output data must conform to an edited sequence or the scanner will not transmit the output data to the host device. When it’s On/Not Required , the scanner will attempt to get the output data to conform to an edited sequence bu...

6 - 1 6 Data Editing Prefix/Suffix Overview When a bar code is scanned, additional information is sent to the host computer along with the bar code data. This group of bar code data and additional, user-defined data is called a “message string.” The selections in this section are used to build the u...

6 - 2 Example: Add a Tab Suffix to All Symbologies Step 1. Scan Add Suffix . Step 2. Scan 9 , 9 from the Programming Chart inside the back cover of this manual to apply this suffix to all symbologies. Step 3. Scan 0 , 9 from the Programming Chart inside the back cover of this manual. This correspond...

6 - 3 Transmit Alternate Extended ASCII Characters You may need to emulate special keyboard functions, such as up or down arrows, Alt/Make or Alt/Break commands, that are not supported in the Extended ASCII Character table. Refer to the Alternate Extended ASCII Characters table, below, for a range o...

6 - 4 Function Code Transmit When this selection is enabled and function codes are contained within the scanned data, the scanner transmits the function code to the terminal. Charts of these function codes are provided in Symbology Charts starting on page A-1 . When the scan- ner is in keyboard wedg...

6 - 5 Intercharacter, Interfunction, and Intermessage Delays Some terminals drop information (characters) if data comes through too quickly. Intercharacter, interfunction, and intermessage delays slow the transmission of data, increasing data integrity. Intercharacter Delay An intercharacter delay o...

6 - 6 Interfunction Delay An interfunction delay of up to 327675 milliseconds (in 5ms increments) may be placed between the transmission of each segment of the message string. Scan the following Interfunction Delay bar code, then scan the number of 5ms delays, and the Save bar code using the Program...

7 - 1 7 Data Formatting Data Format Editor Introduction You may use the Data Format Editor to change the scanner’s output. For example, you can use the Data Format Editor to insert characters at certain points in bar code data as it is scanned. The selections in the following pages are used only if ...

7 - 2 from the Programming Chart inside the back cover of this manual. (Note: 50 characters is entered as 0050. 9999 is a universal number, indicating all lengths.) Step 6. Editor Commands Refer to (page 7-3). Scan the symbols that represent the command you want to enter. Step 7. Scan Save to save y...

7 - 3 Data Format Editor Commands Send Commands Send all characters F1 Include in the output message all of the characters from the input message, starting from current cursor position, followed by an insert character. Syntax = F1xx where xx stands for the insert character’s hex value for its ASCII ...

7 - 4 The data is output as: 1234567890ABCDEFGHIJ<CR> Send all characters up to a particular character F3 Include in the output message all characters from the input message, starting with the character at the current cursor position and continuing to, but not including, the search character “...

7 - 5 Insert bar code length B4 Insert the bar code’s length in the output message, without moving the cursor. The length is expressed as a numeric string and does not include leading zeros. B3 and B4 Example: Insert the symbology name and length Send the symbology name and length before the bar cod...

7 - 6 Move the cursor to the beginning F7 Move the cursor to the first character in the input message. Syntax = F7. FE and F7 Example: Manipulate bar codes that begin with a 1 Search for bar codes that begin with a 1. If a bar code matches, move the cursor back to the beginning of the data and send ...

7 - 7 Search forward for a string B0 Search forward for “s” string from the current cursor position, leaving cursor pointing to “s” string. Syntax = B0nnnnS where nnnn is the string length (up to 9999), and S consists of the ASCII hex value of each character in the match string. For example, B000045...

7 - 8 Search backward for a non-matching character E7 Search the input message backward for the first non-“xx” character from the current cursor position, leaving the cursor pointing to the non-“xx” character. Syntax = E7xx where xx stands for the search character’s hex value for its ASCII code. Ref...

7 - 9 0D is the hex value for a CR The data is output as: 12345678ABC<CR> Stop replacing characters E5 Terminates character replacement. Syntax = E5. Compare characters FE Compare the character in the current cursor position to the character “xx.” If characters are equal, move the cursor forwa...

7 - 10 If this bar code is read, the next data format, if there is one, will be used on this data. If there is no other format, the format fails and the raw data is output as 1234AB . If this bar code is read: the data is output as: AB1234<CR> Insert a delay EF Inserts a delay of up to 49,995 ...

7 - 11 Data Format Non-Match Error Tone When a bar code is encountered that doesn’t match your required data format, the scanner normally generates an error tone. However, you may want to continue scanning bar codes without hearing the error tone. If you scan the Data Format Non-Match Error Tone Off...

7 - 12 Single Scan Data Format Change You can also switch between data formats for a single scan. The next bar code is scanned using an alternate data format, then reverts to the format you have selected above (either Primary, 1, 2, or 3). For example, you may have set your device to the data format...

8 - 1 8 Symbologies This programming section contains the following menu selections. Refer to Chapter 10 for settings and defaults. All Symbologies If you want to decode all the symbologies allowable for your scanner, scan the All Symbologies On code. If on the other hand, you want to decode only a ...

8 - 2 Codabar <Default All Codabar Settings> Codabar On/Off Codabar Start / Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/Stop characters. Default = Don’t Transmit . Codabar Check Character Codabar c...

8 - 3 Codabar Concatenation Codabar supports symbol concatenation. When you enable concatenation, the scanner looks for a Codabar symbol having a “D” start character, adjacent to a symbol having a “D” stop character. In this case the two messages are concatenated into one with the “D” characters omi...

8 - 4 Concatenation Timeout When searching for bar codes during concatenation, you may wish to set a delay used to find the next bar code. Set the length (in milliseconds) for this delay by scanning the following bar code, then setting the timeout (from 1-65535 milliseconds) by scanning digits from ...

8 - 5 Code 39 < Default All Code 39 Settings > Code 39 On/Off Code 39 Start / Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/Stop characters. Default = Don’t Transmit. Code 39 Check Character No Check...

8 - 6 Code 39 Redundancy If you are encountering errors when reading Code 39 bar codes, you may want to adjust the redundancy count. Redun-dancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, th...

8 - 7 Full ASCII If Full ASCII Code 39 decoding is enabled, certain character pairs within the bar code symbol will be interpreted as a single character. For example: $V will be decoded as the ASCII character SYN, and /C will be decoded as the ASCII character #. Default = Off . Character pairs /M an...

8 - 8 Interleaved 2 of 5 < Default All Interleaved 2 of 5 Settings > Interleaved 2 of 5 On/Off NULL Characters Interleaved 2 of 5 requires an even number of characters. When an odd number of characters is present, it is due to NULL characters embedded in the bar code. Scan the On bar code belo...

8 - 9 Interleaved 2 of 5 Redundancy If you are encountering errors when reading Interleaved 2 of 5 bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the...

8 - 10 When Check Digit is set to Validate, but Don’t Transmit , the unit only reads NEC 2 of 5 bar codes printed with a check digit, but will not transmit the check digit with the scanned data. When Check Digit is set to Validate and Transmit , the scanner only reads NEC 2 of 5 bar codes printed wi...

8 - 11 Code 93 < Default All Code 93 Settings > Code 93 On/Off Code 93 Redundancy If you are encountering errors when reading Code 93 bar codes, you may want to adjust the redundancy count. Redun-dancy adjusts the number of times a bar code is decoded before transmission, which may reduce the ...

8 - 12 Straight 2 of 5 Industrial (three-bar start/stop) <Default All Straight 2 of 5 Industrial Settings> Straight 2 of 5 Industrial On/Off Straight 2 of 5 Industrial Redundancy If you are encountering errors when reading Straight 2 of 5 Industrial bar codes, you may want to adjust the redund...

8 - 13 Straight 2 of 5 IATA (two-bar start/stop) <Default All Straight 2 of 5 IATA Settings> Straight 2 of 5 IATA On/Off Straight 2 of 5 IATA Redundancy If you are encountering errors when reading Straight 2 of 5 IATA bar codes, you may want to adjust the redundancy count. Redundancy adjusts t...

8 - 14 Matrix 2 of 5 <Default All Matrix 2 of 5 Settings> Matrix 2 of 5 On/Off Matrix 2 of 5 Check Character No Check Character indicates that the scanner reads and transmits bar code data with or without a check character. When Check Character is set to Validate, but Don’t Transmit , the unit...

8 - 15 Matrix 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 8-1) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 3, Maximum Default = 80. Code 11 <Default All Code 11 Settings> Code 11 On...

8 - 16 Check Digit Validation When Check Character is set to Validate and Transmit , the scanner will only read Code 11 bar codes printed with the specified type check character(s), and will transmit the character(s) at the end of the scanned data. Code 11 Redundancy If you are encountering errors w...

8 - 17 Code 128 <Default All Code 128 Settings> Code 128 On/Off 128 Group Separator Output If you wish to transmit embedded FNC1 characters as group separators (1B hex) with your Code 128 bar code output, scan the On bar code. When Off is scanned, nothing is transmitted for FNC1 characters. De...

8 - 18 Code 128 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 8-1) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 3, Maximum Default = 80. ISBT 128 Concatenation In 1994 the International Society of ...

8 - 19 ISBT 128 Predefined Concatenation Sequences Note: You must enable Code 128 and ISBT 128 to use this feature. The following bar codes are used to select the pre-defined ISBT 128 Concatenation Sequence you wish to use. Once you have selected the concatenation sequence, use ISBT 128 Predefined C...

8 - 20 Default = Off. ISBT 128 User-Defined Concatenation Sequences Note: You must enable Code 128 and ISBT 128 to use this feature. The following bar codes are used to create a custom ISBT 128 Concatenation Sequence. Select the identifiers you want to transmit in the 1st and 2nd positions, both lef...

8 - 21 ISBT 128 User-Defined Concatenation Sequences On/Off The following selections allow you to enable or require the User-Defined ISBT 128 Concatenation Sequences. If you scan Off , the User-Defined concatenation sequences are disabled. If you scan the Allow User-Defined Sequence code, then the s...

8 - 22 Transmit Identifiers You may disable the transmission of the ISBT Code 128 data identifiers by scanning Off . When this selection is Off , the first 2 data (ID) characters are removed from the data stream unless the ISBT code contains the Donation Identification Number identifiers. If the cod...

8 - 23 GS1-128 <Default All GS1-128 Settings> GS1-128 On/Off GS1-128 Application Identifier Parsing This allows a single GS1-128 bar code to be broken into multiple transmissions based on the presence of application iden-tifiers (AI) embedded in the bar code. To use this feature, first enable ...

8 - 24 GS1-128 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 8-1) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 3, Maximum Default = 80. Telepen <Default All Telepen Settings> Telepen On/Off T...

8 - 25 Telepen Redundancy If you are encountering errors when reading Telepen bar codes, you may want to adjust the redundancy count. Redun-dancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, t...

8 - 26 UPC-A Number System and Check Digit UPC-A Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On . UPC-A Number System The numeric system digit of a U.P.C. symbol is normally transmitted at the beginni...

8 - 27 UPC-A Addenda Required When Required is scanned, the scanner will only read UPC-A bar codes that have addenda. You must then turn on a 2 or 5 digit addenda listed on page 8-26 . Default = Not Required. Addenda Timeout You can set a time during which the scanner looks for an addenda. If an add...

8 - 28 UPC-A Redundancy If you are encountering errors when reading UPC-A bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the lo...

8 - 29 UPC-A Number System 5 Addenda Required This setting programs the scanner to require any combination of a coupon code, a 2 digit addenda, or a 5 digit addenda on UPC-A bar codes that begin with a “5.” The following settings can be programmed: Require Coupon Code/Addenda: All UPC-A bar codes th...

8 - 30 Addenda Timeout You can set a time during which the scanner looks for a coupon code. If a coupon code is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for UPC-A/EAN-13 with Extended Coupon Code or UPC-A Number System 4 A...

8 - 31 UPC-E0 Number System The numeric system digit of a UPC-A symbol is normally transmitted at the beginning of scanned data. When using UPC-E Expand, the unit can be programmed so it will not transmit it. Default = On. UPC-E0 Number System and Check Digit UPC-E0 Check Digit Check Digit specifies...

8 - 32 UPC-E0 Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-E data. Default = Off for both 2 Digit and 5 Digit Addenda. UPC-E0 Addenda Required When Required is scanned, the scanner will only read UPC-E bar codes that have addenda. Default = Not Required. Addenda Timeout Yo...

8 - 33 UPC-E0 Addenda Separator When this feature is On , there is a space between the data from the bar code and the data from the addenda. When turned Off , there is no space. Default = Off. UPC-E0 Redundancy If you are encountering errors when reading UPC-E0 bar codes, you may want to adjust the ...

8 - 35 EAN-13 Beginning with 2 Addenda Required This setting programs the scanner to require a 2 digit addenda only on EAN-13 bar codes that begin with a “2.” The follow-ing settings can be programmed: Require 2 Digit Addenda: All EAN-13 bar codes that begin with a “2” must have a 2 digit addendum. ...

8 - 37 EAN-13 Beginning with 434/439 Addenda Required This setting programs the scanner to require any combination of a 2 digit addenda or a 5 digit addenda on EAN-13 bar codes that begin with a “434” or “439.” The following settings can be programmed: Require Addenda: All EAN-13 bar codes that begi...

8 - 38 Default = Don’t Require 2 Digit Addenda. EAN-13 Beginning with 978 Addenda Required These settings program the scanner to require a 5 digit addenda only on EAN-13 bar codes that begin with “978.” The fol-lowing settings can be programmed: Require 5 Digit Addenda: All EAN-13 bar codes that beg...

8 - 39 Addenda Timeout You can set a time during which the scanner looks for an addenda. If an addenda is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for EAN/JAN-13 Addenda Required . Set the length (in milliseconds) for this...

8 - 40 Convert ISBN to 13-Digit When translating EAN-13 codes to the ISBN format, you can convert the bar code to a 13 digit format by scanning the Convert to 13-Digit On bar code below. Default = Convert to 13-Digit Off. ISBN Reformat In normal use, the first two or three digits of an EAN-13 bar co...

8 - 41 ISSN Reformat When Reformat On is scanned, EAN-13 977 Bookland symbols are translated into their equivalent 8-digit ISSN num- ber format, with hyphens added to the output. For example, 9770123456787 will be transmitted as 0123-456-0. (You must first scan ISSN On (page 8-40) before scanning Re...

8 - 43 EAN/JAN-8 Addenda Separator When this feature is On , there is a space between the data from the bar code and the data from the addenda. When turned Off , there is no space. Default = Off. EAN/JAN-8 Redundancy If you are encountering errors when reading EAN/JAN-8 bar codes, you may want to ad...

8 - 44 When Check Character is set to Validate Type 10/11, but Don’t Transmit , the unit will only read MSI bar codes printed with the specified type check character(s), but will not transmit the check character(s) with the scanned data. MSI Redundancy If you are encountering errors when reading MSI...

8 - 45 MSI Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 8-1) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 3, Maximum Default = 80. Plessey Code < Default All Plessey Code Settings > Plessey ...

8 - 46 Plessey Redundancy If you are encountering errors when reading Plessey bar codes, you may want to adjust the redundancy count. Redun-dancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, t...

8 - 47 redundancy, scan the GS1 DataBar Omnidirectional Redundancy bar code below, then scan a redundancy count between 0 and 10 on the Programming Chart inside the back cover of this manual. Then scan the Save bar code. Default = 0. GS1 DataBar Limited < Default All GS1 DataBar Limited Settings ...

8 - 48 GS1 DataBar Expanded < Default All GS1 DataBar Expanded Settings > GS1 DataBar Expanded On/Off GS1 DataBar Expanded Redundancy If you are encountering errors when reading GS1 DataBar Expanded bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times ...

8 - 49 GS1 Emulation The scanner can automatically format the output from any GS1 data carrier to emulate what would be encoded in an equivalent GS1-128 or GS1 DataBar symbol. GS1 data carriers include UPC-A and UPC-E, EAN-13 and EAN-8, ITF-14, GS1-128, and GS1-128 DataBar and GS1 Composites. (Any a...

8 - 50 China Post (Hong Kong 2 of 5) <Default All China Post (Hong Kong 2 of 5) Settings> China Post (Hong Kong 2 of 5) On/Off China Post (Hong Kong 2 of 5) Redundancy If you are encountering errors when reading China Post (Hong Kong 2 of 5) bar codes, you may want to adjust the redundancy cou...

9 - 1 9 Utilities To Add a Test Code I.D. Prefix to All Symbologies This selection allows you to turn on transmission of a Code I.D. before the decoded symbology. (See the Symbology Charts, beginning on page A-1) for the single character code that identifies each symbology.) This action first clears...

9 - 2 EZConfig-Scanning Introduction EZConfig-Scanning provides a wide range of PC-based programming functions that can be performed on a scanner connected to your PC. EZConfig-Scanning allows you to download upgrades to the scanner's firmware, change programmed parameters, and create and print prog...

9 - 3 Resetting the Factory Defaults If you aren’t sure what programming options are in your scanner, or you’ve changed some options and want to restore the scan-ner to factory default settings, first scan the Remove Custom Defaults bar code, then scan Activate Defaults . Power cycle the scanner to ...

10 - 1 10 Serial Programming Commands The serial programming commands can be used in place of the programming bar codes. Both the serial commands and the programming bar codes will program the scanner. For complete descriptions and examples of each serial programming com-mand, refer to the correspon...

10 - 2 SubTag Field Usage When a query is used in place of a SubTag field, the query applies only to the subset of commands available that match the Tag field. In this case, the Data field should not be used because it is ignored by the device. Data Field Usage When a query is used in place of the D...

10 - 3 This response indicates that the device’s Codabar Coding Enable (CBRENA) is set to 1, or on; the Start/Stop Character (SSX) is set to 0, or Don’t Transmit; the Check Character (CK2) is set to 0, or Not Required;concatenation (CCT) is set to 1, or Enabled; the Minimum Message Length (MIN) is s...

10 - 4 Menu Commands Selection Setting * Indicates default Serial Command # Indicates a numeric entry Page Product Default Settings Setting Custom Defaults Set Custom Defaults MNUCDF 1-6 Resetting the Custom Defaults Activate Custom Defaults DEFALT 1-7 Programming the Interface Plug and Play Codes K...

11 - 1 11 Product Specifications Voyager 1200g Product Specifications Parameter Specification Mechanical Height 3.8 in. (97mm) Length 7.1 in. (180mm) Width 2.6 in. (66mm) Weight 4.41 oz. (125g) Electrical Input Voltage 5V + 5% Operating Power 700mW; 140 mA (typical) @ 5V Standby Power 350mW; 70 mA (...

11 - 2 Voyager 1202g and Voyager 1202g-BF Product Specifications Maximum Power Output < 1 mw Embedded Laser Wavelength 645 - 660 nm Divergence < 1.5 mrad. per IEC 60825-1 worst case Maximum Power Output 10 mw Parameter Specification Mechanical Height 3.6 in. (92mm) Length 7.1 in. (180mm) Width...

11 - 3 CCB00-010BT Product Specifications ESD Sensitivity 16kV air9kV contact Scan Performance Pitch, Skew 60°, 60° Scan Pattern Single scan line Scan Angle Horizontal: 30° Scan Speed 100 scan lines per second Print Contrast 10% minimum reflectance difference Decode Capabilities Reads standard 1D an...

11 - 5 CCB00-010BT/CCB00-010BT-01N-VBF Mounting Standard Cable Pinouts Keyboard Wedge 3.07 in (78mm) Use 2 M3x15mm PHP, self-tapping wood screws 10 Pin RJ41 Modular Plug connects to the scanner or the base 1 Cable shield 2 Cable select 3 Supply ground 4 Terminal data 5 Terminal clock 6 Keyboard cloc...

11 - 6 Serial Output Standard Cable Pinouts RS485 Output USB 10 Pin RJ41 Modular Plug connects to the scanner or the base 1 Cable shield 2 Cable select 3 Supply ground 4 Transmit data 5 Receive data - serial data to scanner 6 CTS 7 +5V power 8 RTS 910 Note: Pin assignments are not compatible with Ho...

11 - 7 Voyager 1200g Safety Label Locations Laser Output Compliance Markings information, Part Number, and Serial Number information Compliance Markings information Internal Laser Cautions LASER LIGHT: DO NOT STARE INTO BEAM. CLASS 2 LASER PRODUCT. LASERSTRAHLUNG: NICHT IN DEN STRAHL BLICKEN. LASER ...

12 - 1 12 Maintenance and Troubleshooting Repairs Repairs and/or upgrades are not to be performed on this product. These services are to be performed only by an authorized service center (see Customer Support on page -iii). Maintenance Your device provides reliable and efficient operation with a min...

12 - 2 Replacing an Interface Cable in a Corded Scanner 1. Turn the power to the host system OFF. 2. Disconnect the scanner’s cable from the terminal or computer. 3. Locate the small hole on the underside of the scanner’s handle. This is the cable release. 4. Straighten one end of a paper clip. 5. I...

12 - 3 6. Replace with the new cable. Insert the connector into the opening and press firmly. The connector is keyed to go in only one way, and will click into place. Troubleshooting a Voyager Scanner The scanner automatically performs self-tests whenever you turn it on. If your scanner is not funct...

12 - 4 If you aren’t sure what programming options have been set in the scanner, or if you want the factory default settings restored, refer to Setting Custom Defaults on page 1-6. Troubleshooting a Cordless System Troubleshooting a Base Note: Visit our website ( www.honeywellaidc.com ) to check for...

A - 1 A Reference Charts Symbology Charts Note: “m” represents the AIM modifier character. Refer to International Technical Specification, Symbology Identifiers, for AIM modifier character details. Prefix / Suffix entries for specific symbologies override the universal (All Symbologies, 99) entry. R...

A - 2 Postal Symbologies ASCII Conversion Chart (Code Page 1252) In keyboard applications, ASCII Control Characters can be represented in 3 different ways, as shown below. The CTRL+X func-tion is OS and application dependent. The following table lists some commonly used Microsoft functionality . Thi...

A - 3 Lower ASCII Reference Table Note: Windows Code page 1252 and lower ASCII use the same characters. 1 01 SOH NP Enter CTRL+ A Select all 2 02 STX Caps Lock CTRL+ B Bold 3 03 ETX ALT Make CTRL+ C Copy 4 04 EOT ALT Break CTRL+ D Bookmark 5 05 ENQ CTRL Make CTRL+ E Center 6 06 ACK CTRL Break CTRL+ ...

A - 4 39 27 ' 71 47 G 103 67 g 40 28 ( 72 48 H 104 68 h 41 29 ) 73 49 I 105 69 i 42 2A * 74 4A J 106 6A j 43 2B + 75 4B K 107 6B k 44 2C , 76 4C L 108 6C l 45 2D - 77 4D M 109 6D m 46 2E . 78 4E N 110 6E n 47 2F / 79 4F O 111 6F o 48 30 0 80 50 P 112 70 p 49 31 1 81 51 Q 113 71 q 50 32 2 82 52 R 114...

A - 8 Dec 35 36 64 91 92 93 94 96 123 124 125 126 Hex 23 24 40 5B 5C 5D 5E 60 7B 7C 7D 7E US 0 1 # $ @ [ \ ] ^ ` { | } ~ CA 54 95 # $ à â ç ê î ô é ù è û CA 18 96 # $ à â ç ê É ô é ù è û JP 28 98 # $ @ [ ¥ ] ^ ` { | } ⎯ CN 92 99 # ¥ @ [ \ ] ^ ` { | } ⎯ GB 7 87 £ $ @ [ \ ] ^ ` { | } ˜ FR 3 83 £ $ à °...

A - 9 Keyboard Key References 6E 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 4B 50 55 4C 51 56 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 2C 1F 20 21 22 23 24 25 26 27 28 29 2B 39 2E 2F 30 31 32 33 34 35 36 37 53 4F 54 59 3A 3B 3C 3E 3F 38 40 3D 5A 5F 64 ...

6543210 Matrix 2 of 5 GS1 DataBar (01)00123456789012

Honeywell Scanning & Mobility 9680 Old Bailes RoadFort Mill, SC 29707 VG1200-UG Rev G 3/16