Honeywell 4820 Manual - Free PDF Download

Page 2 - Getting Started

1 Note: Refer to your user’s guide for information about cleaning your device. For localized language versions of this document, go to www.honeywell.com/aidc. Getting Started Turn off the computer’s power before connecting the base, then power up the computer once the base is fully connected. When t...

Page 3 - Keyboard Wedge Connection

2 Keyboard Wedge Connection Serial (RS-232) Connection

Page 4 - Reading Techniques; Note: If the imager beeps 3 times when scanning a

3 Reading Techniques The view finder projects an aiming beam that should be centered over the barcode. (The 4820/4820i can be positioned in any direction for a good read.) Hold the imager over the barcode, pull the trigger, and center the aiming beam on the barcode. The aiming beam is smaller when t...

Page 6 - Keyboard Country; Scan the; Program Keyboard Country; barcode; Save; barcode to program the

5 PC Interface (continued) Keyboard Country Scan the Program Keyboard Country barcode below, then scan the numeric barcode(s) from page 12, then the Save barcode to program the keyboard for your country. As a general rule, the following characters are not supported by the imager for countries other ...

Page 7 - Open Link

6 Note: For complete list of country codes, see the User’s Guide for your product at our website, www.honeywell.com/aidc. Open Link Scan the Open Link barcode, then place the imager into the base to establish a link. Placing a different imager into the base establishes a new link and the old imager ...

Page 9 - Trigger; Note: Streaming presentation mode applies only to

8 Trigger The following barcodes will allow you to use the reader in Manual Trigger mode (need to press the trigger to read) or Presentation mode (the reader is activated when it “sees” a barcode). Streaming Presentation™ (4820/4820i) Note: Streaming presentation mode applies only to units with adva...

Page 10 - Reread Delay; same; barcode a second time. Setting a; Suffix; Add CR Suffix barcode; . To add a tab after the; Add Tab Suffix; barcode to

9 Reread Delay This sets the time period before the imager can read the same barcode a second time. Setting a reread delay protects against accidental rereads of the same barcode. Suffix If you want a carriage return after the barcode, scan the Add CR Suffix barcode . To add a tab after the barcode,...

Page 11 - Note: For complete list of Code IDs, see the User’s; Function Code Transmit

10 Add Code ID Prefix to all Symbologies Scan the following barcode if you wish to add a Code ID prefix to all symbologies at once. Note: For complete list of Code IDs, see the User’s Guide for your product at our website, www.honeywell.com/aidc. Function Code Transmit When this selection is enabled...

Page 12 - Data Format Editor Instructions

11 Data Format Editor Instructions The following are abbreviated instructions for entering a data format. For complete instructions refer to your User’s Guide, available at our website, www.honeywell.com/aidc. 1. Scan the Enter Data Format symbol. 2. Primary/Alternate Format: scan 0 for Primary Form...

Page 13 - Programming Chart

Page 15 - Visual XpressTM; For complete; Technical Assistance

14 Visual Xpress™ To obtain access to additional features for the imager, use Visual Xpress, available from our website at www.honeywell.com/aidc. For complete download instructions and descriptions of Visual Xpress features, refer to your User’s Guide. Technical Assistance If you need assistance in...

Page 16 - Online Technical Assistance; You can also access technical assistance online at; For Further Information; aidc; Product Service and Repair

15 Asia Pacific Telephone - Hong Kong: +852-3188-3485 or 2511-3050Telephone - China: +86 21 6361 3818 E-mail: [email protected] Japan Telephone: +813 5770-6312 E-mail: [email protected] Malaysia Telephone: +603-6201-7020 E-mail: [email protected] Online Technical Assist...

Page 18 - Limited Warranty

17 Online Product Service and Repair Assistance You can also access product service and repair assistance online at www.honeywell.com/aidc . Limited Warranty Honeywell International Inc. ("Honeywell") warrants its products to be free from defects in materials and workmanship and to conform t...

Page 21 - Disclaimer

20 Disclaimer Honeywell International Inc. (“Honeywell”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult Honeywell to determine whether any such changes have been made. The informat...

Page 22 - Honeywell

Honeywell 700 Visions DriveP.O. Box 208Skaneateles Falls, NY 13153-0208 Crdlss-02-QS Rev E 10/08