Hobart XTF - Manual - manualsarea.com

Page 2 - Table Of Contents

Table Of Contents SECTION 1 − SAFETY PRECAUTIONS − READ BEFORE USING 1 . . . . . . . . . . . . . . . . . . . . SECTION 2 − SPECIFICATIONS 2 . . . . . . . . . . . . . . . . . . . . . . . . SECTION 3 − OPERATING INSTRUCTIONS 5 . . . . . . . . . . . . . . SECTION 4 − BATTERY REPLACEMENT 8 . . . . . . ....

Page 3 - Warning! Watch Out! There are possible hazards as shown

Page 1 SECTION 1 − SAFETY PRECAUTIONS − READ BEFORE USING Warning! Watch Out! There are possible hazards as shown in the adjoining symbols. D Read and follow Section 1 for all safety symbols. ARC RAYS can burn eyes and skin. Arc rays from the welding process produce intense visible and invisible (ul...

Page 4 - Lens; Expose the solar cell to bright sunlight for 30 minutes before use.

Page 2 SECTION 2 − SPECIFICATIONS XTF Technical Specifications (Fixed Shade #10) Cartridge Dimensions 4.33 x 3.54 x 0.39 in (110 x 90 x 10 mm) Viewing Field 3.75 x 1.37 in (95 x 35 mm) Reaction Time Light to dark: 0.00028 second (1/3,600) Dark to light: 0.12 second Available Shades Darkened State: #...

Page 6 - XTP Technical Specifications (Professional #9

Page 4 XTP Technical Specifications (Professional #9 − #13 Variable Shade) Cartridge Dimensions 4.33 x 3.54 x 0.39 in (110 x 90 x 10 mm) Viewing Field 3.81 x 1.85 in (97 x 47 mm) Reaction Time 0.0000625 second (1/16,000) Available Shades Darkened State: #9 − 13 / Light State: #4 Sensors Independent/...

Page 7 - 0 minutes after the last; Variable Shade Control; Model XTF

Page 5 SECTION 3 − OPERATING INSTRUCTIONS On/Auto-Off Button Locate the ON button and press ON to weld. The lens will automatically darken twice and then return to the light state. The helmet is then ready to weld. Note: The lens will Auto-Off (clear state − #4) 15 − 20 minutes after the last arc. I...

Page 9 - Warning! Never use the auto-darkening lens without the inside

Page 7 Adjustment of the Headgear for Maximum Comfort There are four adjustments on Hobart headgear that can be adjusted for maximum comfort:1. Headgear Top – Adjusts headgear for proper depth on the head to en- sure correct balance and stability. 2. Headgear tightness – To adjust, turn knob located...

Page 10 - Note; The XTF model has a non-replaceable Lithium battery.; SECTION 5; Cleaning; (Never use solvents or abrasive cleaning de-

Page 8 SECTION 4 − BATTERY REPLACEMENT Model XTV: Remove the batteries by sliding the cover plate to the left. Re- place with 2 AAA alkaline batteries. ( Note: be sure the positive (+) side of the battery is aligned with positive (+) terminal.) Replace cover plate and then press On button.Model XTP:...

Page 11 - Symptom

Page 9 SECTION 6 − TROUBLESHOOTING Symptom Solution Not ON – auto-lens will not darken momentarily when turned on. Check batteries and make sure that they are in good condition and installed properly. Also, check battery surfaces and contacts and clean if necessary. Check battery for proper contact ...

Page 12 - LIMITED WARRANTY; – Subject to the terms and conditions below. Hobart Welding; Proof of purchase is required for warranty transactions so it is

Page 10 SECTION 7 − LIMITED WARRANTY Effective December 1, 2005 LIMITED WARRANTY – Subject to the terms and conditions below. Hobart Welding Retail, Appleton, Wisconsin, warrants to its original retail purchaser that the new Ho- bart equipment sold after the effective date of this limited warranty i...

Page 13 - Description

Page 11 SECTION 8 − REPLACEMENT PARTS Item No. Description Stock No. 1* Kit, Lens Cover Flat Black 770425 Kit, Lens Cover Gloss Black 770426 Kit, Lens Cover Patriot (Blue) 770452 Kit, Lens Cover Red Rivet 770453 Kit, Lens Cover Blaze Orange 770454 2 Replacement XTF Lens 770455 Replacement XTV Lens 7...

Hobart XTF - Manual

Table of Contents:

Summary

Other Hobart Models