Hobart ML-136145 - Manual - manualsarea.com

Page 2 - TABLE OF CONTENTS

– 2 – © HOBART CORPORATION 2007 TABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Accessories & Options . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 3 - Installation, Operation and Care of; SAVE THESE INSTRUCTIONS; GENERAL

– 3 – Installation, Operation and Care of MODEL 3813 & 3913 SLICERS SAVE THESE INSTRUCTIONS GENERAL The model 3813 and 3913 slicers are equipped with a 1 ⁄ 2 HP motor and are available for single-phase electrical service. The slicer features the Hobart CleanCut TM 13" diameter contoured stai...

Page 4 - INSTALLATION; UNPACKING

– 4 – INSTALLATION UNPACKING Immediately after unpacking the slicer, check for possible shipping damage. If the slicer is found to bedamaged, save the packaging material and contact the carrier within 15 days of delivery. Prior to installing the slicer, test the electrical service to assure it agree...

Page 5 - SHARPENER

– 5 – ELECTRICAL This machine is provided with a three-prong grounding plug. The outlet to which this plug is connected must be properly grounded. If the receptacle is not the proper groundingtype, contact an electrician. CLEAN BEFORE USING The 3813 or 3913 slicer must be thoroughly cleaned and sani...

Page 6 - OPERATION; servicing or removing parts. Replace parts before use.

– 6 – TOP KNIFE COVER LATCH KNOB PRODUCT TRAY MEAT GRIP INDEXKNOB PRODUCT TRAY HANDLE MEAT GRIP SLOT GAUGE PLATE MEAT GRIPSLIDE ROD PARK PIN CARRIAGESLOT CONTROLS SIDE PANEL OPERATION Rotating knife. Use meat grip. Unplug machine power cord before cleaning, servicing or removing parts. Replace parts...

Page 7 - To operate the slicer in Automatic mode

– 7 – SLICING — MODEL 3913 • Close the G AUGE P LATE by turning the I NDEX K NOB fully clockwise (Fig. 7). • Pull the P RODUCT T RAY (Fig. 7) all the way toward you until it reaches its stop (this is the home position). • Raise the M EAT G RIP to the top of the P RODUCT T RAY , and rest the P ARK P ...

Page 10 - Using the Knife Removal Tool Accessory

– 10 – Fig. 19 Fig. 21 RIDGE ON KNIFE HUB (PLASTIC COVER REMOVED) PIN @ 1 O’CLOCK HOLE @ 11 O’CLOCK KNIFE REMOVAL TOOL PIN IN HOLE @11 O’CLOCK SLOTS AROUND 3 PINS Using the Knife Removal Tool Accessory U n p l u g t h e m a c h i n e p o w e r c o r d a n d t u r n t h e i n d e x k n o b f u l l y ...

Page 12 - MAINTENANCE; close the gauge plate before doing any maintenance on the slicer.; LUBRICATION — Carriage Slide Rod

– 12 – FORM 35219 (Oct. 2007) MAINTENANCE U n p l u g t h e m a c h i n e p o w e r c o r d a n d t u r n t h e i n d e x k n o b f u l l y clockwise to close the gauge plate before doing any maintenance on the slicer. KNIFE SHARPENING The CleanCut TM K NIFE will provide long service in normal food ...

Hobart ML-136145 - Manual

Table of Contents:

Summary

Other Hobart Models