Hobart HFB12 ML-114909 - Manual

Page 2 - TABLE OF CONTENTS; Programming the HFB12

– 2 – © HOBART CORPORATION, 1997 TABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 4 - INSTALLATION CODES AND STANDARDS; FlashBake oven must be installed in accordance with:; In the United States of America:; State and local codes.; ASSEMBLY; Place the grill on the rollers.; EXHAUST DUCT INSTALLATION; OVEN REAR

– 4 – There must be a 3" (76 mm) clearance on each side of the oven. The area behind the oven around the blowermust be kept clear of obstructions and allow for free air circulation. If your oven is equipped with the power cord and plug, ensure that the cord can be plugged into the appropriateout...

Page 5 - The exhaust system must support 135 cfm.; ELECTRICAL CONNECTIONS

– 5 – The other end of the duct can be vented into an existing hood, or to the outside in a manner consistent with localbuilding codes. The exhaust duct must not be less than 4" (101.5 mm) in diameter, and a recommended maximum length of 4to 6 feet (1219-1829 mm), depending on operating conditio...

Page 6 - Would You Like To; Ground

– 6 – Fig. 2 ELECTRICAL DATA *50A if cord connected. START-UP TESTING After the oven is connected to the supply circuit, perform the following tests to ensure that the oven is operatingproperly. Lamp Test Turn the oven on by pressing the ON/OFF button. After a few seconds, the display will settle on...

Page 7 - Voltage Test

– 7 – Press the 1 button to begin the lamp test. The door will lock and the lamps will each turn on briefly. After eachlamp is turned on successfully, the display will report Lamp OK. If all lamps pass, the oven will automaticallyreturn to the normal operating mode. If a lamp does not operate proper...

Page 8 - OPERATION; PRECAUTIONS; FlashBake

– 8 – OPERATION WARNING: THE OVEN AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, CLEANING, ORSERVICING THE OVEN. PRECAUTIONS • Never attempt to open the oven door while a cook cycle is in progress. Never attempt to operate the ovenwith the door open. • Do not operate the oven without the grill, or ...

Page 18 - BLOWER; The interior cleanliness of the

– 18 – To make the adjustment, press the 1 button. Pressing the 2 button will take you to the normal programmingscreen for the cook time. Pressing the 1 button will take you to the following screen: Recipe 1 1 = lighter . . . 5 = darker Enter (1-5) = 3 Then Press NEXT The factory setting for this ad...

Page 20 - from the back forward.; REMOVING AND INSTALLING THE TOP LAMP SHIELD; Turn the oven off before removing the lamp shield.; FlashBake oven replacements.

– 20 – Fig. 5 OVEN DOOR LAMP SHIELD RAIL UPPER LAMP SHIELD LIFT LAMP SHIELD OVER RETAINING FEATUREPULL LAMP SHIELD TOWARD YOU LOWER LAMP SHIELD (NON REMOVABLE) PL-52646 10. Clean the inside of the oven door window with a cloth dampened with window cleaner. If necessary, use a nylon scouring pad to r...

Page 21 - MAINTENANCE; INSPECTING THE OVEN; Blower

– 21 – MAINTENANCE WARNING: THE OVEN AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, CLEANING ANDSERVICING THE OVEN. WARNING: DISCONNECT THE ELECTRICAL SUPPLY BEFORE PERFORMING ANY MAINTENANCE ONTHE OVEN. Do not remove the oven covers or attempt to open the control cabinet. Doing so will void the wa...

Page 22 - PROBLEM; TROUBLESHOOTING; POSSIBLE CAUSES

– 22 – PROBLEM No power to the oven. No power to the oven controls or display. Blower not operating. Oven not cooking. Display screen does not light up. Grill does not rotate. Door does not lock. No "High Power". TROUBLESHOOTING POSSIBLE CAUSES 1. Oven power cord is not plugged into the wall...

Hobart HFB12 ML-114909 - Manual

Table of Contents:

Summary

Other Hobart Models