Hobart HBR300 - Manual - manualsarea.com

Page 3 - Table of Contents

Bench Receiving Scale Ó Copyright Hobart Corporation 1999 Table of Contents INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 5 - Bench Receiving Scale; SAVE THESE INSTRUCTIONS; Introduction

Bench Receiving Scale 1 Hobart Bench Receiving Scale (HBR300) SAVE THESE INSTRUCTIONS Introduction The HBR300 Bench Receiving Scale features a digital displaywith a 6-button keypad which tilts to create the best viewingangle. The scale also has adjustable legs and a level indicatorto insure proper w...

Page 6 - Manual Overview; The following special instructions are used in the manual:; Note

Bench Receiving Scale 2 Installation and Setupby an AuthorizedHobart Technician Before using your scale for the first time, an AuthorizedHobart Service Technician must install and set up yourscale. This includes:¥ Mounting the display and display pole to the platform.¥ Setting an automatic shut off ...

Page 7 - Using the Scale

Bench Receiving Scale 3 Using the Scale When you are ready to use you scale do the following:¥ Supply power to your scale either by battery (4 D-cell) or a wall-mounted adapter plug. ¥ Level the scale to maintain proper scale balance.¥ Adjust the Display Head for easy viewing. Over ZERO TARE Under A...

Page 8 - Tab

Bench Receiving Scale 4 Supplying Power tothe Scale Power can be supplied to the scale through the AC adapteror optional batteries. The scale uses four (4) D-cell batteriesnot supplied by Hobart. To insert batteries:1. Open the front cover of the display by pulling the tab (located on the back right...

Page 9 - Leveling the Scale; Move the Display Head up or down to your desired; Display Head

Bench Receiving Scale 5 Leveling the Scale There are four (4) leveling legs underneath the scale platter.You may need to adjust these legs if the scale is not seatedproperly. Proper adjustment of these legs helps you tomaintain the proper scale balance. Level the scale by turning the leveling legs r...

Page 10 - Over; Indicator; LOW

Bench Receiving Scale 6 Display Head The Display Head can be adjusted for easy viewing andincludes the display, display indicators, and a 6-buttonkeypad. Display Weight displays in lb (pounds) or kg (kilograms) andindicator arrows illuminate on the display. TARE ZERO Over Under Accept NetWt. Gross W...

Page 11 - Keypad; Operator Mode; FUNCTION; KEYPAD; Turns the scale on or off.

Bench Receiving Scale 7 Keypad You can use the 6-button keypad to perform functions intwo modes:¥ Operator Mode¥ Setup Mode Operator Mode In Operator Mode you can do the following using thekeypad:¥ Weigh products¥ Operate one-touch tare¥ Weigh items in batches¥ Toggle between net and gross weight¥ T...

Page 12 - Setup Mode

Bench Receiving Scale 8 Setup Mode Setup Mode is used to program the scale with specificsettings before weighing the product. In Setup Mode you can set, clear, or change:¥ Preset tare¥ Upper and lower weight limits lb kg NET GROSS ON OFF CLEAR ZERO FUNCTION TARE KEYPAD Key Function ON OFF Turns the ...

Page 13 - Operating the Scale; Tip; Presetting Tare

Bench Receiving Scale 9 Operating the Scale Refer to the specific section for a further explanation of eachstep. To operate the scale: 1. PRESS ON OFF to turn the scale on. 2. Access Setup Mode to preset tare and set upper and lower limits if desired. 3. Access Operator Mode to operate one-touch tar...

Page 14 - Empty 20 quart Mixer Bowl

Bench Receiving Scale 10 ☛ Note When setting the tare value, only the flashing digit can bechanged. 2. PRESS lb kg to increase flashing digit by one. --OR-- PRESS NET GROSS to decrease the flashing digit by one. 3. PRESS TARE to move left one digit. The digit to the left flashes and you can increase...

Page 15 - Clearing a Preset Tare

Bench Receiving Scale 11 Clearing a Preset Tare To clear a preset tare:1. Remove product and container from scale platter. The preset tare weight displays. 2. HOLD DOWN FUNCTION and PRESS TARE . The tare indicator and last digit flashes. 3. PRESS CLEAR ZERO . The set tare value clears, 0.0 displays,...

Page 18 - over

Bench Receiving Scale 14 Operating in OperatorMode Access Operator Mode to operate one-touch tare, weighproducts, and weigh items in batches. Weighing a Product UsingOne-Touch Tare If you do not know the package weight (tare value), useone-touch tare. To operate one-touch tare:1. Place the container...

Page 19 - Weighing in Batches; Cleaning; DO NOT

Bench Receiving Scale 15 Weighing in Batches Weighing in batches allows you to add ingredients andreturn the weight back to zero repeatedly by pressing Tareto control the weight of each added ingredient type. To batch:1. Place the container on the scale platter. The container weight displays. 2. PRE...

Page 20 - Sanitizing; Do; Bleach; ¥ Promptly remove expired batteries.

Bench Receiving Scale 16 Sanitizing Do Don’t DO use 5% Chlorine Bleach (5.25%Sodium Hypochlorite).Ratio Bleach Water Concentration 1 : 250 1 tsp. 1 gal. 200 ppm 1 : 500 1/2 tsp. 1 gal. 100 ppm 1 : 1000 1/4 tsp. 1 gal. 50 ppm 1 : 2000 1/8 tsp. 1 gal. 25 ppm DONÕT exceed chemicalmanufacturerÕs recomme...

Page 21 - Error Messages; Error Message; POWERING THE SCALE

Bench Receiving Scale 17 Error Messages Error Message Possible Cause Action Item on platter is too heavy. Remove the item and PRESS CLEAR ZERO . Something is stuck between theupper and lower platter covers,or the upper platter cover hasbeen removed. Remove the item stuck between thecovers or replace...

Page 22 - TOP VIEW

Bench Receiving Scale 18 Accessory(Mobile Cart) An optional mobile cart with rear locking casters is available.Contact your local Hobart Representative for further details. 33.960 16.850 14.000 34.793 43.750 4X .500 WIDTH TREAD 1.250 WIDTH TREAD 1.250 TOP VIEW SIDE VIEW REAR VIEW 18.500 4X .500

Hobart HBR300 - Manual

Table of Contents:

Summary

Other Hobart Models