Hitachi X200 - Manual - manualsarea.com

Page 4 - Standard Specifications; General Specifications

1-/3-phase 200V class Standard Specifications 3 General Specifications 3-phase 400V class 002SFEF2 002NFU2 002LFRF2 0.2(1/4) 0.50.51.4 004SFEF2 004NFU2 004LFRF2 0.4(1/2) 1.01.02.6 005SFEF2 -- 0.55(3/4) 1.11.23.0 007SFEF2 007NFU2 007LFRF2 0.75(1) 1.51.64.0 011SFEF2 -- 1.1(1.5) 1.92.05.0 015SFEF2 015N...

Page 5 - Dimensions

Dimensions 4 143(5.63) 155(6.10) 80(3.15)67(2.64) 5(0.20) 5(0.20) 6(0.24) 4.4(0.17) 93(3.66) 13(0.51) 2.6(0.10) Wall 143(5.63) 155(6.10) 80(3.15) 67(2.64) 5(0.20) 5(0.20) 6(0.24) 4.4(0.17) 107(4.21) 27(1.06) 2.6(0.10) Wall 176(6.93) 189(7.44) 110(4.33) 98(3.86) 5(0.20) 5(0.20) 6(0.24) 4.4 (0.17) 128...

Page 6 - Operation and Programming; Setting the maximum output frequency

Operation and Programming 5 (1) or the value previously monitored is displayed. (1) or the value previously monitored is displayed. (1) or the value previously monitored is displayed. (2)The motor runs at the frequency set by the potentiometer. (3)The motor stops. (2)Function code appears. (3) appea...

Page 7 - Operation / Terminal Functions; Hardware switches; Control circuit terminals

RS-485 communication/operator selection switch Safety stop ON/Off switch SW7 SW8 ON OFF 485 OPE Operation / Terminal Functions 6 Hardware switches Terminal Description Terminal Symbol Jumper Jumper L1 / N +1 + - U/T1 V/T2 W/T3 Jumper L1 L2 L3/N SFEF2 NFU2, LFU2, LFRF2 Jumper +1 + - U/T1 V/T2 W/T3 Ju...

Page 8 - Function List; Monitoring and main profile parameters

Function List 7 Monitoring and main profile parameters A Group: Standard functions : Allowed [ X: Not allowed ] Lo Hi The parameter tables in this chapter have a column titled "Run Mode Edit." An Ex mark x means the parameter cannot be edited; a Checkmark means the parameter can be edited. T...

Page 9 - A Group: Standard functions

Function List 8 A Group: Standard functions b Group: Fine-tuning functions : Allowed [ X: Not allowed ] : Allowed [ X: Not allowed ] PID Control PID Control AVR function Operation mode and acc./dec. function External freq. tuning Frequency caluculation A061A261A062A262A063A064A065A066A067A068A071A07...

Page 10 - C Group: Intelligent terminal functions

Function List 9 C Group: Intelligent terminal functions : Allowed [ X: Not allowed ] Note: C014: 01 for UL version. Run mode edit Function Code Name Range Default -EF(CE) -U(UL) -R(JP) Unit Lo Intelligent input terminal C001C201C002C202C003C203C004C204C005C205 Terminal [1] functionTerminal [1] funct...

Page 11 - Protective Functions; Error Codes

OC.Drive OC.Decel OC.Accel Over.C Over.L Over.V EEPROM Under.V CPU EXTERNAL USP GND.Flt OV.SRC OH FIN DRIV TH EMERGENCY COMM Protective Functions 10 Name Over current Overload protection *1 Over voltage protection EEPROM error *2,3 Under-voltage error CPU error External trip USP *4 Ground fault *5 I...

Page 12 - Connecting Diagram; Source type logic

Connecting Diagram 11 AL2 AL1 AL0 R(L1) T/N(L3) S(L2) (T1) U (T3) W (T2) V P24 4 5 3 2 1 PCS L AM H O OI L DC24V DC10V 11 CM2 (+ 1 ) PD ( + ) P ( - ) N DC link choke Motor Intelligent relayoutput contacts Intelligent outputterminal Current input 4mA~20mA X200 Intelligent input terminals (5 terminals...

Page 13 - Sink type logic

Connecting Diagram 12 !"# "$"% $#&#$ %#'( ")$*)$ "$' $+ $#&#$ ")$*)$ $#%,' )%%#$ *)$ ,-, : $#&#$ *)$ $#%,'+ $#%,'+ $(*# !"%$ .'% -/.$ #%,' 1111 11 ",," "& 2 ")% # "& 2 "$# 2 ",," $#%,'+ '%# 3#*#3 " "& 4 "...

Page 14 - Wiring and Accessories

13 Wiring and Accessories L1 L2 L3 U (T1) V (T2) W (T3) +1 + - IM Power Supply Fuse Inverter Motor Note 1: Field wiring connection must be made by a UL and c-UL listed closed-loop terminal connector sized for the wire gauge involved. Connector must be fixed using the crimping tool specified by the c...

Page 15 - Torque characteristics/Derating Curves; Base frequency = 60Hz; Torque characteristics

14 Torque characteristics/Derating Curves 150 130 95 80 5545 35 100 1 6 20 60 120 Output torque (%) Base frequency = 60Hz Base frequency = 50Hz 100 130 150 7555 4535 90 1 5 16.7 50 120 Output frequency (Hz) Output frequency (Hz) Output torque (%) 0 . 2 ~ 4 k W 0 . 2 ~ 4 k W 5.5 , 7.5 k W Continuous ...

Page 16 - For Correct Operation; Application to Motors; Notes on Use

For Correct Operation 15 Application to Motors The overspeed endurance of a general-purpose motor is 120% of the rated speed for 2 minutes (JIS C4,004). For operation at higherthan 60Hz, it is required to examine the allowable torque of the motor, useful life of bearings, noise, vibration, etc. In t...

Page 17 - Main power supply; Precaution for Correct Usage

Unbalance factor of voltage = V RS -(V RS +V ST +V TR )/3 (V RS +V ST +V TR )/3 Max. line voltage (min.) - Mean line voltage Mean line voltage x100 = x100 = x100 =1.5(%) 205-202 202 For Correct Operation 16 In the following examples involving a general-purpose inverter, a large peak current flows on...

Page 18 - MEMO

Hitachi X200 - Manual

Table of Contents:

Summary

Other Hitachi Models