Hisense HWFY1014 User Manual - Free PDF Download

Page 4 - SAFETY INFORMATION

The manufacturer reserves the right for any modifications on the product which might be deemed necessary or useful without informing about it in this IFU. Before operating your new washing machine, please read this instruction carefully, and keep it for future reference. If you have lost it accident...

Page 6 - ensure; the; Push

3 ensure Important: Transport bolts which are not removed can cause damage to the appliance. Screw off all transportation bolts for approx. 30mm with wrench following the direction of arrow shown (not fully screw it off). Push four transportation bolts on horizontal direction inward and loose transp...

Page 7 - direction until it clicks.; thickness; Adjustment of the feet

Pull out transportation bolt together with rubber part and plastic part. To ensure safety and reduce noise, you should install the transportation bolt cover supplied with the unit (see the annex accompanying the unit). Lean and place the transportation bolt into hole and press it following the shown...

Page 8 - machine can be used without the bottom cover.; Noise-Reduction Bottom Plate Installation Instructions; Install bottom cover

To realize quieter operation, a bottom cover is supplied with the unit (only applies to some of the Hisense washers). After installing the cover at the bottom of the washer, the noise level will be greatly reduced. Please ask for advice from specialists before installing the cover, nevertheless, the...

Page 9 - the hot water

Double sided tape Right-angle impression Before installing the noise-reduction bottom plate, align and paste the acoustic absorption wool with and along the right-angle impression on bottom plate (this procedure is unnecessary for some of the models without acoustic absorption wool). Remove surface ...

Page 10 - In case the drain hose is installed as shown below:; Drain; Connect the

In case the drain hose is installed as shown below: Unhook it only from the right clip (see arrow) Connect the drain hose to the Drain or hook it over the edge of a sink by means of the "U" bend. Fit the “U” bend show in E, if not already installed, if it at the end of the drain hose. Ensure...

Page 12 - that

9 en the from the mains supply, , the mains. The symbol on the product, or on the documents accompanying the product, indicates that this appliance may not be treated as household waste. Instead it shall be handed over to the applicable collection point for there cyclingof electrical and electronic ...

Page 13 - Never open the door forcibly or use it as a step.; DESCRIPTION OF THE WASHING MACHINE

Control panel layout and appearance will depend on the model. 10 Clean the outside of the washing machine with a damp cloth. Do not use abrasive detergents. Never open the door forcibly or use it as a step. DESCRIPTION OF THE WASHING MACHINE EMERGENCY DOOR OPENING In case of failure to open the door...

Page 17 - unds; or D

1 4 unds Press the release lever in the main wash compartment downward and remove the drawer(fig.“B or D ”). Remove siphon in softener slot. (fig.“C or E ”). Refit the siphon in the detergent drawer and fit the drawer back inside its housing. B C D E

Page 18 - if it fails to perform spin cycles.; Ensure that the water has

1 5 2 Insert removal tool like slotted screwdriver into the small opening of bottom baffle, press the bottom baffle downward with much strength and open it. 1 if it fails to perform spin cycles. Ensure that the water has We recommend that you check and clean the filter regularly, at least two or thr...

Page 20 - solv; too

Page 21 - remove some

Page 22 - Hot / Cold fill fault - For Models with Dual Inlets; filter on the rear side of machine.; For Models with Single Inlet

19 Hot / Cold fill fault - For Models with Dual Inlets If you wish to connect hot and cold water supply (Fig.1): 1. Fix the red marked inlet hose to the hot water tap and to the inlet valve with the red filter on the rear side of machine. 2. Fix the other inlet hose to the cold water tap and to the ...

Page 23 - a. “F01” displayed on screen; The machine is not fed with water or insufficient water. Check:; b. “F03” displayed on screen; Spin

2 0 Fault Code List Displayed on Display Window Fault Description “F01” Water inflow fault “F03” Drainage fault Electronic module fault. “F13” Door lock fault “F14” Door unlock fault “Unb” Unbalance alarm Overflow or too much foam. “F24” else fault code, “F04-F98” Ensure that a. “F01” displayed on s...

Page 24 - nb” is shown; Fault code; power supply and contact after-sale service.; If

2 1 nb” is shown Unbalance alarm shall be solved by the following methods 1.Laundry winding Turn the knob to “off” for 3 seconds for shutdown, open the door, shake the clothes and put them back into the washing machine, then select the single dewatering program to dry again. 2.Too light-weighted lau...