Page 3 - Table of Contents
Table of Contents 1 1. Warranty and Service .................................................... 3 2. Preface ......................................................................... 4 3. Description of Warning Symbols ..................................... 5 4. Safety Notices .........................
Page 5 - Warranty and Service
3 The instructions on this manual are for the model(s) listed on the front cover. Before you start reading, check your product number by looking at the rear of your TV. Thank you for purchasing our Liquid Crystal Display Television (LCD TV). With this product, you will be able to enjoy superior audi...
Page 6 - Copyright; Preface
4 This manual is designed to assist users in setting up and using the LCD TV. Information in this document has been carefully checked for accu-racy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. Copyright © Co...
Page 7 - Electric Power Notice; Warning; Description of Warning Symbols
5 Electric Power Notice Electric power may cause personal injury and mechanical damage if it is misused. Although safety has been taken into consideration during the design and production of this product, electric shock or fire can result when the product is misused. To prevent potential danger, fol...
Page 8 - Power Supply Safety Notes; To avoid electric shocks, do not use an extended power cord or; Installation Safety Notes; Antenna; Safety Notices
6 Power Supply Safety Notes 1. To avoid electric shocks, do not use an extended power cord or an outlet that does not match this product's plug or leaves the plug exposed. 2. This product has a 3-pin grounded plug. The third pin connects to ground; do not remove it. 3. If the power cord or plug is d...
Page 10 - Optimal Viewing Area
8 Optimal Viewing Area CH VOL MU TE ME NU SOU RCE 160 cm 11
Page 11 - Important Safety Instructions; Do not block any ventilation openings. Install
9 Important Safety Instructions 1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer ’s ins...
Page 13 - Personal Safety
11 Personal Safety To avoid overloading the power supply, do not plug too many electrical devices into an outlet or extension cable. Dangerous high-voltage electric power compo-nents are located inside the TV. To avoid electric shock, do not disassemble the casing. Do not place or drop metals, small...
Page 14 - Installation
12 Installation To avoid damage to power circuits, do not place the TV in locations where there is excessive steam or dust. Do not place the TV on a bed, sofa, carpet, or in a sealed cabinet to avoid blocking the product's vents. Install the outdoor antenna far from power trans-mission lines to avoi...
Page 16 - FCC Compliance Statement; that to which the receiver is connected; : A shielded-type power cord is required in order to meet FCC; Regulatory Information
14 FCC Compliance Statement 1 This device complies with part 15 of the FCC Rules. Operation is sub-ject to the following two conditions: (1) This device may not cause harm-ful interference, and (2) this device must accept any interference received, including interference that may cause undesired ope...
Page 18 - Features; Introducing the TV
16 Thank you for purchasing this Liquid Crys-tal Display TV. Your TV is designed to be safe, versatile, and easy to use. The rebound design makes it a fun addi-tion to any room. You can watch standard NTSC television channels, and easily connect a VCR, VCD, or DVD player to the standard CVBS and S-V...
Page 19 - Checking Package Contents
17 Make sure the following components are included in the box. Contact your vendor immediately if anything is missing or damaged. TV User ’s Manual Quick Start Guide Warranty and Service Manual Wire Material Package Power Cord Power Adapter 4-IN-1 Cable VOL MUTE MENU SOURCE CH User's Manual Quick St...
Page 20 - Front View; Description; VOL–; Signal; Getting to Know Your TV
18 Front View Description Function 1 Headphone line out Connects to headphones. 2 Adjust Volume Volume up ( VOL+): Increases the volume. Volume down ( VOL– ): Decreases the volume. 3 Mute Press this button to eliminate sound. Press this button again or press the volume adjust buttons directly to res...
Page 22 - Input and Output Por ts
20 Input and Output Por ts Description Function 1 DC-IN Connects to the included power adapter. 2 Line out Connects to external amplifier. 3 AV2 Use the included 4-IN-1 Audio/Video cable to connect external devices, such as a VCR, VCD, or DVD player. Audio Input: AV connectors white and red audio ca...
Page 24 - Connecting to an Antenna or Cable TV; Connect the other end of the VHF/UHF (Antenna) or CATV cable to; Getting Started
22 Connecting to an Antenna or Cable TV 1 Connect one end of the VHF/UHF (Antenna) or CATV cable to the ANT Jack (VHF/UHF IN Jack) on the back of the TV. 2 Connect the other end of the VHF/UHF (Antenna) or CATV cable to the Antenna or CATV socket. NoteIf you cannot receive channels after connecting ...
Page 25 - Connecting to AV Devices; Connecting to a VCR, VCD or DVD Player
23 Connecting to AV Devices Connect external devices such as VCD/DVD players or VCRs to the TV using the AV1 and AV2 ports on the back of the TV. Connecting to a VCR, VCD or DVD Player The illustration presented here shows you how to connect your TV to a VCR, VCD or DVD player. Actual connections ma...
Page 26 - Connecting to a Video Camera; connector; AV
24 Connecting to a Video Camera The following illustration shows you how to connect the TV to a cam-corder. Actual connections may vary according to the make and model of the device. Refer to the user’s manual included with the camcorder for more detailed instructions. DC-IN LINE OUT AV 2 ANT R L VI...
Page 27 - Connecting Headphones; Notes; Headphone; line out port
25 Connecting Headphones Headphones may be used to listen to the TV instead of using the built-in speakers. Connect headphones to the headphone line out port as illustrated. Notes • Headphones are not included with the product. • The internal TV speakers will not output sound when headphones are plu...
Page 28 - Connecting an Amplifier or Speakers; Speakers
26 Connecting an Amplifier or Speakers (Build-in amplifier) Connect an external amplifier or speakers to the line out port to pro-vide better sound quality. Refer to the following illustration. L R DC-IN LINE OUT AV 2 ANT R L VIDEO S-VIDEO AV1 DC-IN LINE OUT AV 2 ANT Speakers Line out Amplifier (Bui...
Page 29 - Connecting the Power Adapter; Connect the power cord to the power adapter as illustrated.; Power cord
27 Connecting the Power Adapter 1 Connect the power cord to the power adapter as illustrated. 2 Plug the power adapter connector into the DC-IN on the rear panel of the TV. 3 Plug the three-pronged plug at the other end of the power cord into a power outlet. DC-IN LINE OUT AV 2 ANT R L VIDEO S-VIDEO...
Page 30 - Using the Remote Control; Using the TV
28 Using the Remote Control For best results, use the remote control within a distance of 5 meters (16 feet) from the front of the TV’s signal sensor. Do not exceed an angle of 30 degrees when pointing at the signal sensor. Refer to the following illustration. CH VO L MU TE ME NU SO UR CE 30 30 5m 3...
Page 31 - Tur ning the TV On and Off; POWER; Selecting Channels; CH UP; Power button
29 Tur ning the TV On and Off 1 Press POWER on the remote control or on the TV control panel. The power LED indicator on the front of the TV changes from red to green, indicating that the power is on. 2 Press the POWER button again. The power LED changes from green to red, indicating that the TV is ...
Page 32 - SOURCE; Adjusting the Volume; VOL UP; Source; Volume up
30 Switching Source Signals Press SOURCE to select differ- ent source signals. CH, AV1, and AV2 appear on the top right corner of the screen in that order. NoteThe TV supports S-Video input in addition to normal video and audio signals. The TV detects the signal type automatically and gives priority...
Page 33 - OSD Setting Menus; Press; Settings
31 The On-Screen Display (OSD) menu system provides a quick and simple method to adjust your TV’s settings. This chapter describes how to change each of the available settings. The OSD can be used with either the front panel control or remote control. The following sections explain how to adjust set...
Page 34 - Note; Picture Setting; to enter the; Press the; button to enter
32 Note You can operate the OSD with either the front panel control or the arrow buttons on the remote control. Picture Setting Press MENU to enter the OSD Main Menu screen. Press the VOL UP button to enter the PICTURE Menu. MENU VOL CH SEL SEL ENTER ENTER MENU MENU MAIN AUDIO TV CUSTOMIZE MENU PICT...
Page 35 - Brightness; BRIGHTNESS
33 Brightness 1 Press the VOL UP button. The brightness slide bar appears. 2 Press the VOL UP button to increase the brightness. 3 Press the VOL DOWN button to decrease the brightness. 4 Press MENU to confirm the setting and return to the Picture Menu. SEL SEL PRESET COLOR HUE SHARPNESS CONTRAST BRI...
Page 36 - Contrast; CONTRAST
34 Contrast 1 Press the CH DOWN button to select CONTRAST. 2 Press the VOL UP button. The con- trast slide bar appears. 3 Press the VOL UP button to increase the contrast. 4 Press the VOL DOWN button to decrease the contrast. 5 Press MENU to confirm the setting and return to the Picture Menu. SEL SE...
Page 37 - Sharpness; SHARPNESS
35 Sharpness 1 Press the CH DOWN button to select SHARPNESS. 2 Press the VOL UP button. The sharpness slide bar appears. 3 Press the VOL UP button to increase the sharpness. 4 Press the VOL DOWN button to decrease the sharpness. 5 Press MENU to confirm the setting and return to the Picture Menu. SEL...
Page 38 - Hue; HUE
36 Hue 1 Press the CH DOWN button to select HUE. 2 Press the VOL UP button. The hue slide bar appears. 3 Press the VOL UP button to increase the hue toward the green end of the spectrum. The image becomes more green. 4 Press the VOL DOWN button to decrease the hue toward the red end of the spectrum....
Page 39 - Saturation; SATURATION
37 Saturation 1 Press the CH DOWN button to select SATURATION. 2 Press the VOL UP button. The satu- ration slide bar appears. 3 Press the VOL UP button to increase the saturation. 4 Press the VOL DOWN button to decrease the saturation. 5 Press MENU to confirm the setting and return to the Picture Me...
Page 40 - Color; Neutral Color
38 Color 1 Press the CH DOWN button to select COLOR. 2 Press the VOL UP button. The cur- rent setting appears blinking in the brackets. Neutral Color Press the VOL UP button to select NEUTRAL, then press MENU . “NEU- TRAL” appears in the brackets. Warm Color Press the VOL UP button to select WARM, t...
Page 41 - Preset; CH DOWN; button to
39 Preset 1 Press the CH DOWN button to select PRESET. 2 Press the VOL UP button. “OK” appears in the brackets. All picture settings are returned to the factory-set default values. SEL SEL SEL SEL PRESET HUE SHARPNESS CONTRAST BRIGHTNESS PICTURE MENU 0 0 0 0 30 SATURATION ENTER ENTER ENTER ENTER MEN...
Page 42 - Audio Setting
40 Note You can operate the OSD with either the front panel control or the arrow buttons on the remote control. Audio Setting Press MENU to enter the OSD Main Menu screen. 1 Press the CH UP/CH DOWN button to select AUDIO. 2 Press the VOL UP button to enter the Audio Menu. MENU VOL CH MAIN AUDIO TV C...
Page 43 - Treble; TREBLE
41 Treble 1 Press the VOL UP button. The tre- ble slide bar appears. 2 Press the VOL UP button to increase the treble. 3 Press the VOL DOWN button to decrease the treble. 4 Press MENU to confirm the setting and return to the Audio Menu. SEL SEL SEL SEL ENTER ENTER ENTER ENTER MENU MENU MENU MENU BAL...
Page 44 - Bass; BASS
42 Bass 1 Press the CH DOWN button to select BASS. 2 Press the VOL UP button. The bass slide bar appears. 3 Press the VOL UP button to increase the bass. 4 Press the VOL DOWN button to decrease the bass. 5 Press MENU to confirm the setting and return to the Audio Menu. SEL SEL SEL SEL ENTER ENTER EN...
Page 45 - Balance; BALANCE
43 Balance 1 Press the CH DOWN button to select BALANCE. 2 Press the VOL UP button. The bal- ance slide bar appears. 3 Press the VOL DOWN button to shift the balance to the left speaker. 4 Press the VOL UP button to shift the balance to the right speaker. 5 Press MENU to confirm the setting and retu...
Page 46 - ENHANCE
44 Surround Enhance 1 Press the CH DOWN button to select SURROUND. 2 Press the VOL UP button to enter the setting field. 3 Press the VOL UP button to turn surround on or off. 4 Press MENU to confirm your choice. 1 Press the CH DOWN button to select ENHANCE. 2 Press the VOL UP button to enter the set...
Page 48 - TV Setting; to enter the OSD
46 Note You can operate the OSD with either the front panel control or the arrow buttons on the remote control. TV Setting Press MENU to enter the OSD Main Menu screen. 1 Press the CH UP/ CH DOWN button to select TV. 2 Press the VOL UP button to enter the TV Menu. MENU VOL CH SEL SEL ENTER ENTER MEN...
Page 49 - The default TV setting is “CATV”.
47 TV/CATV 1 Press the VOL UP button. The cur- rent setting appears flashing in the brackets. Receiving Cable TV Press the VOL UP button to select CATV, then press MENU . “CATV” appears in the brackets. Receiving Broadcast TV Press the VOL UP button to select TV, then press MENU . “TV” appears in th...
Page 50 - Add Channel; Erase Channel; VOL DOWN; ou can still access the erased channel
48 Channel Add/Erase 1 Press the CH DOWN button to select CH ADD/ERASE. 2 Press the VOL UP button. The OSD menu display switches to the fol-lowing screen. Press the CH UP/CH DOWN button on the front panel to select a channel. Add Channel Then press the VOL UP button on the front panel to add the sel...
Page 51 - Auto Program; button to begin
49 Auto Program 1 Press the CH DOWN button to select AUTO PROGRAM. 2 Press the VOL UP button to begin auto programming. The screen dis-plays channels incrementally as the TV scans for available channels. TVTV/CATV CH AUTO PROGRAM ADD/ERASE MENU SEL SEL ENTER ENTER MENU MENU CATV AUTO PROGRAM TV 44 N...
Page 52 - Customize Setting
50 Note You can operate the OSD with either the front panel control or the arrow buttons on the remote control. Customize Setting Press MENU to enter the OSD Main Menu screen. 1 Press the CH UP/ CH DOWN button to select AUDIO. 2 Press the VOL UP button to enter the Audio Menu. MENU VOL CH MAIN AUDIO...
Page 53 - Sleep Timer; The sleep timer turns the TV off automatically after a set time.
51 Sleep Timer The sleep timer turns the TV off automatically after a set time. 1 Press the VOL UP button to select a value: OFF, 30, 60, 90, or 120 minutes. 2 Press MENU to confirm your choice. You can also press SLEEP on the remote control to select 30, 60, 90 or 120 minutes. The setting appears o...
Page 54 - The default language is Traditional Chinese.
52 OSD Timeout This setting allows you to set the length of time the OSD menus appear on the screen when a button is not pressed. Language 1 Press the CH DOWN button to select OSD TIMEOUT. 2 Press the VOL UP button. The cur- rent setting appears flashing in the brackets. 3 Press the VOL UP button to...
Page 55 - Taking Care of Your TV
53 Turn the power off before you begin cleaning the TV. For best results, use a clean lens cloth to remove dust and fingerprints from the screen. Do not wipe the shell of the TV with alcohol, methanol, gasoline or oil products to avoid dam-aging the finish. Wipe the shell with a dry soft cloth and u...
Page 56 - Troubleshooting
54 Situation Solution No picture and sound. • Connect the power cord properly. • Press the POWER button on the control panel or remote control. • Press the SOURCE button to cycle through connected video sources. • Press the CH UP or CH DOWN button to switch to other TV stations. • Check the TV/CATV ...
Page 58 - Specifications
56 ST03-15A1 LCD Panel Size 15-inch TFT Aspect Ratio 4:3 Best Resolution 1024 (horizontal) x 768 (vertical) Maximum Display Area 304.1 mm (H) x 228.1mm (V) TV System NTSC Video System AV1: Composite Video (RCA jack; yellow + S-Video)AV2: mini-DIN 10-pin (Composite + S-Video) Audio System AV1: L/R RC...
Page 59 - Glossary
57 Aspect Ratio The ratio of width to height of a film, image or display screen. Broadcast TV Broadcasting video signals using high-frequency electromagnetic waves to distribute television channels to viewers (standard TV broadcast). CATV Community Antenna Television, the original name for cable TV....
