Page 2 - Table of Contents
Table of Contents 1 1. Regulatory Information ................................................... 32. Description of Warning Symbols ..................................... 53. Safety Notices ............................................................... 64. Preface .....................................
Page 4 - Regulatory Information; FCC Compliance Statement; to which the receiver is connected; Warning; : You are cautioned that changes or modifications not
3 1 Regulatory Information FCC Compliance Statement 1 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that m...
Page 6 - Description of Warning Symbols; Before You Proceed; Read all Safety Notices in Section 2 of this manual and; CAUTION; WARNING
5 2 Description of Warning Symbols Before You Proceed 1. Read all Safety Notices in Section 2 of this manual and instructions in the User ’s Manual carefully before either plugging in or turning the TV on. 2. Keep this User ’s Manual in a safe place for future reference. Keep the box and packaging i...
Page 7 - Safety Notices; Electric Power Notice; To avoid electric shocks, do not use an extended power cord or
6 3 Safety Notices Electric Power Notice Electric power may cause personal injury and mechanical damage if misused. Although safety has been taken into consideration during the design and production of this TV, electric shock or fire can result if the TV is misused. To prevent potential danger, read...
Page 8 - Installation Safety Notes; Antenna; Power
7 Installation Safety Notes Antenna We suggest that you use an outdoor antenna to get the best signal possible unless you have cable TV or a centralized indoor antenna system. You may, however, use an antenna indoors if it is placed in a location free from interference. Location Avoid prolonged expo...
Page 9 - IMPORTANT SAFETY INSTRUCTIONS
8 IMPORTANT SAFETY INSTRUCTIONS 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings. 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with dry cloth. 7 Do not block any ventilation openings. Install in accordance with manufacturer ’s instructions....
Page 11 - Personal Safety; Do not allow children to use the TV unattended.
10 Personal Safety To avoid overloading the power supply, never plug too many electrical devices into an outlet, power strip, or extension cable. Dangerous high-voltage electric power components are located inside the TV. To avoid electric shock, do not disassemble the TV in any way. Do not place or...
Page 12 - Installation
11 Installation Do not place the TV in locations where there is excessive steam or dust. Avoid blocking the TV's vents, do not place the TV on a bed, sofa, carpet, or in a sealed cabinet. Install the outdoor antenna (not included) away from power transmission lines to avoid possible danger. Unplug t...
Page 14 - Preface
13 4 Preface Thank you for purchasing a Hannspree Liquid Crystal Display Television (LCD TV). Your new TV will allow you to enjoy superior audio and video while enriching your lifestyle with advanced technology. Please carefully read this manual in its entirety before setting up, using or operating ...
Page 15 - Copyright; © Copyright 2004 Hannspree California Inc.
14 Copyright © Copyright 2004 Hannspree California Inc. All rights reserved. This manual is protected by copyright and distributed under licenses restricting its use, copying and distribution. No part of this manual may be reproduced in any form by any means without the prior written authorization o...
Page 16 - Introducing the TV; Features
15 5 Introducing the TV Thank you for purchasing this LCD TV. Your LCD TV is designed to be safe, versatile, and easy to use. The design makes it a fun addition to any room. You can watch broadcast or cable television channels, and easily connect a VCR, VCD or DVD player to the standard RCA and S-Vi...
Page 17 - Checking Package Contents
16 6 Checking Package Contents Make sure the following components are included in the box. Please contact Hannspree Customer Service immediately if anything is missing or damaged. • TV• User’s manual• Quick start guide• Warranty and service manual• Power cord• Power adapter• 4-IN-1 A/V cable• Remote...
Page 18 - Getting Started; Control Panel
17 7 Getting Started Control Panel Description Icon Function Power Turns the TV on and off. Power LED Indicates power status. Source SOURCE / TV / AV / TV Selects the input source to be displayed (TV/CATV, AV1, or AV2). Menu Turns the On-Screen Display (OSD) menu on and off. Select channel channel u...
Page 19 - Input and Output Jacks; Description
18 Input and Output Jacks Description Connector Function AV1 (R-AUDIO/ L-AUDIO/VIDEO) Connects to a right audio (red) or left audio (white) cable, or video (yellow) cable. AV2 Use the included 4-IN-1 A/V cable to connect external devices, such as a VCR, VCD, DVD player, CVBS RCA cables or a game dev...
Page 20 - Remote Control
19 Remote Control Description Icon Function Menu Press this button to activate the OSD menu system and to adjust various settings and personal preferences. Arrow W / X / < / > Press W and X to scroll through the on-screen display menus. Favorite channels can be selected using the W and X butto...
Page 22 - Inser ting the Remote Control Batter y/Batteries; Lithium battery/batteries; Note
21 Inser ting the Remote Control Batter y/Batteries Lithium battery/batteries 1 Open the battery compartment cover at the back of the remote control (A). 2 Slide the battery/batteries, with the positive (+) side facing up, underneath the shorter set of metal contacts (B). 3 Press the battery/batteri...
Page 23 - AAA battery/batteries
22 AAA battery/batteries 1 Open the battery compartment cover at the back of the remote control (A). 2 Insert the battery/ batteries paying attention to the polarity markings inside the battery compartment (B). 3 Replace the battery compartment cover (C). Note Your remote control may have either AAA...
Page 25 - Making Connections; Connecting to an Antenna or Cable TV
24 8 Making Connections Connecting to an Antenna or Cable TV 1 Connect one end of the VHF/UHF (Antenna) or CATV cable to ANT Jack (VHF/UHF IN Jack) on the back of the TV. 2 Connect the other end of the VHF/UHF (Antenna) or CATV cable to the antenna socket or CATV cable. Note If you cannot receive ch...
Page 26 - Connecting to AV Devices; R W Y
25 Connecting to AV Devices Connect external devices such as a VCR, VCD or DVD player, or video game console to the TV using the supplied 4-IN-1 A/V cable. Connecting to a VCR/VCD/DVD Player The illustration presented here shows how to connect the TV to a VCR, VCD or DVD player. Actual connections m...
Page 27 - Connecting to a Video Camera; AV connectors
26 Connecting to a Video Camera The instructions presented here are a general guide to connecting the TV to a camcorder or other type of digital camera. Actual connections may vary according to the make and model of the device. Refer to the user’s manual included with the camcorder or camera for mor...
Page 28 - Connecting Exter nal Speakers or Headphones; Notes
27 Connecting Exter nal Speakers or Headphones External speakers or headphones may be used to listen to the TV rather than using the built-in speakers. Connect external speakers to the speaker line out port or headphones to the headphone port as illustrated. Notes • External speakers or headphones a...
Page 29 - Connecting the Power Adapter; Connect the power cord to the power adapter as illustrated.
28 Connecting the Power Adapter 1 Connect the power cord to the power adapter as illustrated. 2 Plug the power adapter connector into the DC-IN input jack on the rear panel of the TV. 3 Insert the three-pronged plug at the other end of the power cord into a power outlet. DC-IN input jack Power cord ...
Page 30 - Using the TV; Using the Remote Control; Tur ning the TV On and Off; Press power; Selecting Channels; Press source to select the incoming source signal.; Adjusting the Volume
29 9 Using the TV Using the Remote Control For best results, use the remote control within a distance of 16 feet (5 meters) from the front of the TV. Do not exceed an angle of 30 degrees when pointing at the TV. Notes • The operational distance may be shortened when the signal sensor is directly exp...
Page 31 - Settings; OSD Setting Menu
30 10 Adjusting On-Screen Display (OSD) Settings The On-Screen Display (OSD) menu system provides a quick and simple method to adjust your TV’s settings. This chapter describes how to change each of the available settings. The OSD can be used with either the remote control or the control panel. Note...
Page 32 - Press channel down
31 Brightness 1 Press menu. The brightness slide bar is highlighted. 2 Press channel up to increase the brightness. 3 Press channel down to decrease the brightness. 4 Press menu to confirm the setting and return to the Main Menu. Note The new setting is confirmed automatically when the OSD times out...
Page 33 - Press channel down or channel up
32 Contrast 1 Press channel down or channel up to select Contrast. 2 Press menu. The contrast slide bar is highlighted. 3 Press channel up to increase the contrast. 4 Press channel down to decrease the contrast. 5 Press menu to confirm the setting and return to the Main Menu. Note The new setting is...
Page 35 - Hue
34 Hue 1 Press menu to enter the Hue submenu. 2 Press channel up to increase green and decrease red. 3 Press channel down to decrease green and increase red. 4 Press menu to confirm the setting and return to the Video Setting menu. Note The new setting is confirmed automatically when the OSD times o...
Page 36 - Saturation
35 Saturation 1 Press channel down or channel up to select Saturation. 2 Press menu to enter the Saturation submenu. 3 Press channel up to increase the saturation. 4 Press channel down to decrease the saturation. 5 Press menu to confirm the setting and return to the Video Setting menu. Note The new ...
Page 37 - Sharpness
36 Sharpness 1 Press channel down or channel up to select Sharpness. 2 Press menu to enter the Sharpness submenu. 3 Press channel up to increase the sharpness. 4 Press channel down to decrease the sharpness. 5 Press menu to confirm the setting and return to the Video Setting menu. Note The new setti...
Page 38 - Color Temperature; Standard Color
37 Color Temperature 1 Press channel down or channel up to select Color Temp. 2 Press menu to enter the Color Temperature submenu. There are three default color temperatures to Choose from. Standard Color Press channel down or channel up to select Standard, then press menu. Warm Color Press channel ...
Page 39 - to select Audio
38 Audio Setting Press menu to enter the OSD Main Menu screen. 1 Press channel down or channel up to select Audio Setting. 2 Press menu to enter the Audio Setting menu. Main Menu ETC Audio Setting
Page 40 - BASS
39 Treble 1 Press menu to enter the Treble sub-menu. 2 Press channel up to increase the treble. 3 Press channel down to decrease the treble. 4 Press menu to confirm the setting and return to the Audio Setting menu. Note The new setting is confirmed automatically when the OSD times out. TRE TRE BASS ...
Page 44 - to select TV
43 TV Setting Press menu to enter the OSD Main Menu screen. 1 Press channel down or channel up to select TV Setting. 2 Press menu to enter the TV Setting menu. Main Menu ETC TV Setting
Page 45 - CH
44 TV/CATV 1 Press menu to enter the TV/CATV submenu. Receiving Cable TV Press channel up to select CATV, then press menu. Receiving Broadcast TV Press channel down to select TV, then press menu. Note The new setting is confirmed automatically when the OSD times out. TV Setting TV/CATV TV CATV A M +...
Page 46 - MTS; Stereo
45 MTS 1 Press channel down or channel up to select MTS. 2 Press menu to enter the MTS submenu. Select from the following options. Stereo Press channel down to select Stereo. A green dot appears and Stereo is highlighted in yellow. Press menu again to confirm the selection. SAP Press channel up to s...
Page 47 - Auto Program
46 Auto Program 1 Press channel down or channel up to select Auto Program. 2 Press menu to enter the Auto Program Setting submenu. 3 Press channel down or channel up to select ON or OFF and press menu. The screen shows “Auto Program...” and the channel indicator increments from 2 to 69 (ANT connecti...
Page 48 - Manual Program; Press channel down or
47 Manual Program 1 Press channel down or channel up to select “Manual Program”. 2 Press menu to enter the Manual Program submenu. 3 Press channel down or channel up to find the channel you want to add. Press menu to select the channel. 4 Press menu to exit, and then access Channel Add/Erase functio...
Page 49 - Add Channel; Press menu to select channel.; Erase Channel
48 Channel Add/Erase 1 Select the channel you want to add or delete, for example, Channel 28. 2 Press channel down or channel up to select CH. Add/Erase. 3 Press menu to enter the Channel Add/Erase submenu. Select from the following options. Add Channel 1 Press channel down or channel up to select A...
Page 50 - Favorite Channel
49 Favorite Channel 1 Press channel down or channel up to select Favorites CH. Edit. 2 Press menu to enter the Favorites CH. Edit submenu. 3 The screen displays the four favorite channels: M1, M2, M3, and M4. 4 Press channel down or channel up to select the channel number you want to set for M1. Pre...
Page 51 - Miscellaneous Setting; to select
50 Miscellaneous Setting Press menu to enter the OSD Main Menu screen. 1 Press channel down or channel up to select Miscellaneous Setting. 2 Press menu to enter the Miscellaneous Setting menu. Main Menu ETC Miscellaneous Miscellaneous
Page 52 - Language; English
51 Language 1 Press menu to enter the Language submenu. 2 The screen displays the available OSD languages: English and Español. 3 Press channel down or channel up to select a language. The OSD language changes as soon as you select a language. 4 Press menu to confirm your choice. Miscellaneous Langu...
Page 53 - Sleeper; off
52 Sleeper The sleeper turns the LCD TV off automatically after a set period of time. 1 Press channel down or channel up to select Sleeper. 2 Press menu to enter the Sleeper submenu. 3 The screen displays the available sleeper setting:– OFF– 30 minutes– 60 minutes– 90 minutes– 120 minutes 4 Press ch...
Page 54 - OSD Display; Press menu to confirm your choice.; All
53 OSD Display This setting allows you to set the amount of information that appears on the LCD screen when display is pressed. You can choose from three settings: Off, Portion, or All. 1 Press channel down or channel up to select OSD Display. 2 Press menu to enter the OSD Display submenu. 3 The scr...
Page 55 - Time Setting; This setting allows you to set the TV clock.
54 Time Setting This setting allows you to set the TV clock. 1 Press menu to enter the OSD menus. 2 Press channel up or channel down to select Miscellaneous. 3 Press menu to enter the Miscellaneous menu. 4 Press channel down or channel up to select Time Setting. 5 Press menu to enter the Time Settin...
Page 56 - Reset; Exit turns off the OSD menus and returns you to TV mode.
55 Reset The Reset function returns all of your LCD TV’s user settings to their factory defaults. Warning: The reset function erases all of your custom and favorite channel settings, and will reset all display settings (such as contrast, brightness, etc.) to the factory default values. The reset fun...
Page 58 - Troubleshooting; Situation
57 12 Troubleshooting Situation Solution No picture and sound. • Connect the power cord properly. • Check if the power LED is on or not. • Press power on the control panel or remote control. • Press source to cycle through connected video sources. • Press channel up or channel down to switch to othe...
Page 60 - Warranty and Service
59 13 Warranty and Service For complete warranty service information, please refer to the “Warranty and Service Manual” enclosed with your TV.
Page 61 - Specifications
60 14 Specifications 9.6 / 12.1-in ch LCD TV LCD Panel Size 9.6 / 12.1-inch TFT Aspect Ratio 4:3 Display Resolution 800 (horizontal) x 600 (vertical) TV System NTSC Video System AV1: RCA jackAV2: S-Video Input and Composite Video Input (through the 4-IN-1 A/V cable) Audio System AV1: RCA left & ...
Page 62 - Glossary; LCD
61 15 Glossary Aspect Ratio: The ratio of width to height of a film, image or display screen. Broadcast TV: Broadcasting video signals using high-frequency electromagnetic waves to distribute television channels to viewers (standard TV broadcast). CATV: Community Antenna Television, the original nam...
