Page 2 - Table of Contents
Table of Contents 1 1. Warranty and Service .................................................... 3 2. Preface ......................................................................... 4 3. Description of Warning Symbols ..................................... 5 4. Safety Notices .........................
Page 4 - Warranty and Service
3 The instructions on this manual are for the model(s) listed on the front cover. Before you start reading, check your product number by looking at the rear of your TV. Thank you for purchasing our Liquid Crystal Display Television (LCD TV). With this product, you will be able to enjoy superior audi...
Page 5 - Copyright; Preface
4 This manual is designed to assist users in setting up and using the LCD TV. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. Copyright © Cop...
Page 6 - Electric Power Notice; Warning; Description of Warning Symbols
5 Electric Power Notice Electric power may cause personal injury and mechanical damage if it is misused. Although safety has been taken into consideration during the design and production of this product, electric shock or fire can result when the product is misused. To prevent potential danger, fol...
Page 7 - Power Supply Safety Notes; To avoid electric shocks, do not use an extended power cord or; Installation Safety Notes; Antenna; Safety Notices
6 Power Supply Safety Notes 1. To avoid electric shocks, do not use an extended power cord or an outlet that does not match this product's plug or leaves the plug exposed. 2. This product has a 3-pin grounded plug. The third pin connects to ground; do not remove it. 3. If the power cord or plug is d...
Page 9 - Optimal Viewing Distance
Page 10 - Important Safety Instructions; Do not block any ventilation openings. Install
9 Important Safety Instructions 1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer ’s ins...
Page 12 - Personal Safety
11 Personal Safety To avoid overloading the power supply, do not plug too many electrical devices into an outlet or extension cable. Dangerous high-voltage electric power compo-nents are located inside the TV. To avoid electric shock, do not disassemble the casing. Do not place or drop metals, small...
Page 13 - Installation
12 Installation To avoid damage to power circuits, do not place the TV in locations where there is excessive steam or dust. Do not place the TV on a bed, sofa, carpet, or in a sealed cabinet to avoid blocking the product's vents. Install the outdoor antenna far from power trans-mission lines to avoi...
Page 15 - FCC Compliance Statement; that to which the receiver is connected; : A shielded-type power cord is required in order to meet FCC; Regulatory Information
14 FCC Compliance Statement 1 This device complies with part 15 of the FCC Rules. Operation is sub-ject to the following two conditions: (1) This device may not cause harm-ful interference, and (2) this device must accept any interference received, including interference that may cause undesired ope...
Page 17 - Features; Introducing the TV
16 Thank you for purchasing this Liquid Crystal Display TV. Your LCD TV is designed to be safe, versatile, and easy to use. The semi-truck design makes it a fun addition to any room. You can watch broadcast or cable television channels, and easily con-nect a VCR, VCD, or DVD player or a game device ...
Page 18 - Checking Package Contents
17 Make sure the following components are included in the box. Contact your vendor immediately if anything is missing or damaged. TV User ’s Manual Quick Start Guide Warranty and Service Manual Wire Material Package Power Cord Power Adapter 4-IN-1 Cable RCA Jack x 3 The tapes on the corners of the s...
Page 19 - Front View; Description; CH; Getting to Know Your TV
18 Front View Description Function 1 Power LED Green LED indicates power on. 2 Power Turns the TV on and off. 3 Menu Turns the On-Screen Display (OSD) menus on and off. 4 Source Selects the input source to be displayed (TV/CATV, AV, or S-Video). 5 Select channel Changes channels. Press CH S to inc...
Page 20 - Input and Output Por ts
19 Input and Output Por ts Description Function 1 SPEAKER Connects to headphones/speakers or other audio device. 2 AV Connects to VCR/VCD/DVD player CVBS RCA cables or a game device. 3 DC 12V Connects to the included power adapter. 4 ANT Connects to an antenna or CATV cable television line. SPEAKER ...
Page 21 - Attaching the Semi Cab; Refer to the illustration below.; Put the trailer pin (
20 Attaching and Detaching the Semi Truck This section describes how to attach and detach the Semi Truck cab. Attaching the Semi Cab Refer to the illustration below. A B B C D 1 Push the switch ( A ) and push the legs down ( B ). 2 Put the trailer pin ( C ) into the cab hole ( D ) as shown.
Page 22 - Detaching the Semi Cab; Place the LCD panel
21 Detaching the Semi Cab You can detach the cab from the LCD panel. Refer to the illustration below. 1 Pull the cab away from the LCD panel. 3 Place the LCD panel on a stable surface. 2 Pull the legs up.
Page 23 - Connecting to an Antenna or Cable TV; Connect the other end of the VHF/UHF (Antenna) or CATV cable to; ANT jack; Getting Started
22 Connecting to an Antenna or Cable TV 1 Connect one end of the UHF or CATV cable to the ANT Jack (VHF/UHF IN Jack) on the back of the TV. 2 Connect the other end of the VHF/UHF (Antenna) or CATV cable to the antenna socket or CATV cable. NoteIf you cannot receive channels after connecting to an an...
Page 24 - Connecting to AV Devices; B R W Y
23 Connecting to AV Devices Connect external devices such as a VCR, VCD or DVD player, or video game to the TV using the 4-IN-1 cable. Connecting to a VCR/VCD/DVD Player The illustration presented here shows how to connect the TV to a VCR and VCD or DVD player. Actual connections may vary accord-ing...
Page 25 - Connecting to a Video Camera; Note; connector
24 Connecting to a Video Camera The instructions presented here are a general guide to connecting the TV to a camcorder or other type of digital camera. Actual connec-tions may vary according to the make and model of the device. Refer to the user’s manual included with the camcorder or camera for mo...
Page 26 - Connecting to a Game Device; Notes; R W Y
25 Connecting to a Game Device The instructions presented here are a general guide to connecting the TV to a game device using the RCA Jacks provided (some game devices may require a unique adapter that is not provided). Actual connections may vary according to the make and model of the game device....
Page 27 - Connecting Exter nal Speakers or Headphones; Headphones
26 Connecting Exter nal Speakers or Headphones External speakers or headphones may be used to listen to the TV rather than using the built-in speakers. Connect external speakers or headphones to the headphone line out port as illustrated. Notes • External speakers or headphones are not included with...
Page 28 - Connecting the Power Adapter; Connect the power cord to the power adapter as illustrated.; Power cord
27 Connecting the Power Adapter 1 Connect the power cord to the power adapter as illustrated. 2 Plug the power adapter connector into the DC-IN input jack on the rear panel of the TV. 3 Insert the three-pronged plug at the other end of the power cord into a power outlet. DC-IN input jack SPEAKER SPE...
Page 29 - Using the Remote Control; Using the TV
28 Using the Remote Control For best results, use the remote control within a distance of 5 meters from the front of the TV’s signal sensor. Do not exceed an angle of 30 degrees when pointing at the signal sensor. Refer to the following illustration. 30 30 5m 3m 3m 10 Using the TV
Page 30 - Tur ning the TV On and Off; Press the; button on; POWER; button; CH UP; button; button; Power LED
29 Tur ning the TV On and Off 1 Press the POWER button on the control panel (or remote control) . The power LED changes from dark to green, indicating that the power has been turned on. 2 Press the POWER button again; the power LED changes from green to dark, indicating that the TV is in off mode. S...
Page 31 - Current source setting
30 Switching Source Signals Press SOURCE on the remote control or control panel to select the incoming source signal. The current source setting (TV/CATV, S-Video, or AV) appears on the top left corner of the screen. NoteThe TV supports S-Video input in addition to normal video and audio sig- nals. ...
Page 32 - Button Descriptions; OSD Setting Menu; Settings
31 The On-Screen Display (OSD) menu system provides a quick and simple method to adjust your TV’s settings. This chapter describes how to change each of the available settings.The OSD can be used with either the remote control or the front con-trol panel. The following sections explain how to adjust...
Page 33 - Brightness; MAX
32 Brightness 1 Press MENU to enter the OSD menus. 2 Press the CH UP button or CH DOWN button to select Brightness. 3 Press MENU . The brightness slide bar appears. 4 Press CH UP button to increase the brightness. 5 Press CH DOWN button to decrease the brightness. 6 Press MENU to confirm the setting...
Page 34 - Contrast
33 Contrast 1 Press MENU to enter the OSD menus. 2 Press the CH UP button or CH DOWN button to select Contrast. 3 Press MENU . The contrast slide bar appears. 4 Press CH UP button to increase the contrast. 5 Press CH DOWN button to decrease the contrast. 6 Press MENU to confirm the setting and retur...
Page 35 - Video Setting; MENU
34 Video Setting Press the MENU button to enter the OSD menus. 1 Press the CH UP button or CH DOWN button to select Video Setting. 2 Press MENU to enter the Video Setting menu. ETO ETO M a i n M e n u V i d e o S e t t i n g E N T E R
Page 36 - Hue
35 Hue 1 Press the CH UP button or CH DOWN button to select Hue. 2 Press MENU to enter the Hue menu. 3 Press CH UP button to increase the hue towards the red spectrum. The image becomes more red. 4 Press CH DOWN button to decrease the hue towards the green spectrum. The image becomes more green. 5 P...
Page 37 - Saturation
36 Saturation 1 Press the CH UP button or CH DOWN button to select Saturation. 2 Press MENU to enter the Saturation menu. 3 Press CH UP button to increase the saturation. The screen image becomes more vibrant. 4 Press CH DOWN button to decrease the saturation. The screen image becomes less vibrant. ...
Page 38 - Sharpness
37 Sharpness 1 Press the CH UP button or CH DOWN button to select Sharpness. 2 Press MENU to enter the Sharpness menu. 3 Press CH UP button to increase the sharpness. 4 Press CH DOWN button to decrease the sharpness. 5 Press MENU again to confirm the setting and return to the Video Set-ting menu. V ...
Page 39 - Color Temperature; Standard Color
38 Color Temperature 1 Press the CH UP button or CH DOWN button to select Color. 2 Press MENU to enter the Color menu. The following three color temperatures are available. Standard Color Press the CH UP button or CH DOWN button to select Standard, then press MENU . Warm Color Press the CH UP button...
Page 40 - Audio Setting
39 Audio Setting Press the MENU button to enter the OSD menus. 1 Press the CH UP button or CH DOWN button to select Audio Setting. 2 Press MENU to enter the Audio Setting menu. ETO ETO M a i n m e n u A u d i o S e t t i n g E N T E R
Page 41 - Treble
40 Treble 1 Press the CH UP button or CH DOWN button to select Treble. 2 Press MENU to enter the Treble menu. 3 Press CH UP button to increase the treble. 4 Press CH DOWN button to decrease the treble. 5 Press MENU to confirm the setting and return to the Audio Setting menu. E N T E R A u d i o S e ...
Page 42 - Bass
41 Bass 1 Press the CH UP button or CH DOWN button to select Bass. 2 Press MENU to enter the Bass menu. 3 Press CH UP button to increase the bass. 4 Press CH DOWN button to decrease the bass. 5 Press MENU to confirm the setting and return to the Audio Setting menu. E N T E R A u d i o S e t t i n g ...
Page 43 - Balance
42 Balance 1 Press the CH UP button or CH DOWN button to select Balance. 2 Press MENU to enter the Balance menu. 3 Press CH UP button to shift the bal- ance to the right speaker. 4 Press CH DOWN button to shift the balance to the left speaker. 5 Press MENU to confirm the setting and return to the Au...
Page 44 - TV Setting
43 TV Setting Press the MENU button to enter the OSD menus. 1 Press the CH UP button or CH DOWN button to select TV Setting. 2 Press the MENU button to enter the TV Setting menu. ETO ETO M a i n M e n u T V S e t t i n g E N T E R
Page 46 - MTS
45 MTS 1 Press the CH UP button or CH DOWN button to select MTS. 2 Press MENU to enter the MTS menu. MAIN1 Press the CH UP button or CH DOWN button to select MAIN (default). MAIN is highlighted in red. 2 Press MENU again to confirm the selection. SAP1 Press the CH UP button or CH DOWN button to sele...
Page 47 - Auto Program; Channel Indicator
46 Auto Program 1 Press the CH UP button or CH DOWN button to select Auto Program. 2 Press MENU to enter the Auto Pro- gram menu. 3 Press the CH UP button or CH DOWN button to select Yes or No. 4 Press MENU . The screen goes blank and the chan-nel indicator values range from 2 to 69 (antenna connect...
Page 48 - Manual Program
47 Manual Program This function allows you to locate channels for adding to or erasing from preset channels. 1 Press the CH UP button or CH DOWN button to select Manual Pro- gram. 2 Press MENU to enter the Manual Program menu. 3 Press the CH UP button or CH DOWN buttons to find the channel you want ...
Page 50 - Miscellaneous Setting
49 Miscellaneous Setting Press the MENU button to enter the OSD menus. 1 Press the CH UP button or CH DOWN button to select Miscellaneous. 2 Press MENU to enter the Mis- cellaneous menu. ETO M a i n M e n u M i s c e l l a n e o u s E N T E R
Page 51 - OSD Position; The following options are available.
50 OSD Position 1 Press the CH UP button or CH DOWN button to select OSD Position. 2 Press MENU to enter the OSD Position menu. The following options are available. Horizontal Position1 Press the CH UP button or CH DOWN button to select H. Position. 2 Press MENU . 3 Press CH DOWN button to move the ...
Page 52 - Language
51 Language 1 Press the CH UP button or CH DOWN button to select Language. 2 Press MENU to enter the Language menu.The screen displays the available OSD languages: English and T-Chinese (Traditional Chinese). 3 Press the CH UP button or CH DOWN button to select a language. 4 Press MENU to confirm yo...
Page 53 - Sleep Timer
52 Sleep Timer The sleep timer turns the TV off automatically after a set period of time. 1 Press the CH UP button or CH DOWN button to select Sleep. 2 Press MENU to enter the Sleep menu. 3 The screen displays the available sleep timer setting: – Off– 30 minutes– 60 minutes– 90 minutes– 120 minutes ...
Page 55 - Reset
54 Reset The Reset function returns all of your TV’s user settings to their fac-tory defaults. Warning: The reset function will erase all of your custom and favorite channel settings, and will reset all display settings (such as contrast, bright-ness, etc.) to the factory default values. The reset f...
Page 56 - Taking Care of Your TV
55 Turn the power off before you begin cleaning the TV. For best results, use a clean lens cloth to remove dust and fingerprints from the screen. Do not wipe the shell of the TV with alcohol, methanol, gasoline or oil products to avoid dam-aging the finish. Wipe the shell with a dry soft cloth and u...
Page 57 - Troubleshooting
56 Situation Solution No picture and sound. • Connect the power cord properly. • Press the POWER button on the control panel or remote control. • Press the SOURCE button to cycle through connected video sources. • Press the CH UP button or CH DOWN but- ton to switch to other TV stations. • Check the...
Page 59 - Specifications
58 K223-10A1 LCD Panel Size 9.6-inch TFT Aspect Ratio 4:3 Best Resolution 800 (horizontal) x 600 (vertical) Maximum Display Area 194.4 mm (H) x 145.8 mm (W) TV System NTSC Video System S-Video Input and Composite Video Input (through the 4-IN-1 cable) Audio System Input: RCA Jack (L/R Audio Input th...
Page 60 - Glossary
59 Aspect Ratio The ratio of width to height of a film, image or display screen. Broadcast TV Broadcasting video signals using high-frequency electromagnetic waves to distribute television channels to viewers (standard TV broadcast). CATV Community Antenna Television, the original name for cable TV....
Page 61 - VCD
60 with camcorders, VCRs, and quality receivers and amplifiers to provide sharper pic- tures. VCD A compact disk format developed in 1993 by Sony and Philips to capture full- motion video. A standard Video CD can hold 74 minutes of near VHS-quality video and CD-quality sound.
