Page 2 - tABle of contents; IMPORTANT DISPOSAL INSTRUCTIONS; Before use; MAINTENANCE
tABle of contents IMPORTANT DISPOSAL INSTRUCTIONS As a responsible retailer we care about the environment. As such we urge you to follow the correct disposal procedure for your product and packaging materials. This will help conserve natural recourses and ensure that it is recycled in a manner that ...
Page 3 - components; ThANkS fOR PURChASINg A hAIER PRODUCT
03 Before use 1x Inlet hose assembly 1x drain hose bracket 1x User manual 4x Blanking plugs Delay components ThANkS fOR PURChASINg A hAIER PRODUCT Please read these instructions carefully before using this appliance. The instructions contain important information which will help you get the best out...
Page 4 - Filter cover; PREPARINg ThE MAChINE; prepArAtion
04 Before use T1 T2 T3 S1 S2 S4 S3 T4 Control paneldoor handleWork topWasher doorStart/Pausedetergent distribution drawer Filter cover PREPARINg ThE MAChINE Remove all the packing materials to prevent unsteadiness, including the polystyrene base. Upon opening the package, water drops may be seen on ...
Page 5 - sAfety instructions; BEfORE SwITChINg ThE APPLIANCE ON fOR ThE fIRST TIME
05 Before use sAfety instructions dO ... ... Make sure that the transport bolt are removed. ... Use a separate earthed socket for the power supply. ... Make sure that the plug is accessible. ... Hold the plug and not the electric cable when unplugging the power supply. ... Make sure that the fuses i...
Page 6 - DISMANTLE ThE TRANSPORTATION BOLTS; ADjUSTINg ThE wAShINg MAChINE; instAllAtion
06 Before use 3. 1. 2. 4. DISMANTLE ThE TRANSPORTATION BOLTS The transportation bolts are designed for clamping anti-vibration components inside of the washing machine during the transportation process. Remove the back cover. 1. Remove the four bolts on the rear side and take out the synthetic 2. st...
Page 7 - INLET hOSE; CONNECTINg TO ThE POwER SUPPLy
07 Before use 1. 2. 1. 8 0 -1 0 0c m 2. INLET hOSE 1. Connect the nut on the inlet hose to the connector on the water valve. 2. Apply inlet hose to a water tap with cold, fresh water. Note: Use the hose-set supplied with the appliance. Old hose-sets should not be reused. DRAIN hOSE 1. Use the drain ...
Page 8 - OPERATIONAL fUNCTIONS; control pAnel
08 Before use A B C D E F G H K L J OPERATIONAL fUNCTIONS control pAnel A Program knob B Power Switch C Start/Pause button D Spinning Speed Setting button E Washing temperature button f delay Button g detergent distribution drawer h display I Intense button J Extra rinse button k Rinse hold A ¬ Prog...
Page 10 - using the APPLiAnCe; progrAm selection; PROgRAM MODES
2 1 3 1 Detergent compartment for prewash mode2 Detergent compartment3 Compartment for softener and other additives 10 using the APPLiAnCe progrAm selection PROgRAM MODES Preset spin speed Program Maximum Preset 2 3 1 Recommended Laundry hW80-1401B-u hW70-1401B-u hW70-1401s-u hW70-1401-u hW70-1201B-...
Page 11 - consumption AnD technicAl DAtA; TEChNICAL DATA
11 using the APPLiAnCe consumption AnD technicAl DAtA TEChNICAL DATA CONSUMPTION TABLE The wash cycle times are intended as a guide only. The actual time used may vary due to different water pressure, initial water temperature, etc.WARNINg: Never overload the washing machine. See below for maximum l...
Page 12 - WAshing methoDs; POwER SUPPLy; PREPARINg ThE LAUNDRy; pleAse note
12 using the APPLiAnCe WAshing methoDs POwER SUPPLy Connect the washing machine to the power supply (220V to 240V~/50Hz). wATER CONNECTION Turn on the tap. The water must be clean and clear. Note: Before use, check for leakage in the joints between the tap and the inlet hose by turning on the tap. P...
Page 13 - LOADINg ThE MAChINE; SELECTINg DETERgENT; ADDINg DETERgENT
13 using the APPLiAnCe LOADINg ThE MAChINE Open the washer door, put in the laundry piece by piece. Close the door tightly. ¬ When first using the washing machine, let it run unloaded for one program to prevent the laundry from being tainted by oil or dirty water from the washing machine. Before was...
Page 14 - SETTINg wAShINg TEMPERATURE
14 using the APPLiAnCe SETTINg wAShINg TEMPERATURE Press and hold down the temperature button until the desired temperature is selected . SETTINg SPIN SPEED Press and hold down the speed button until the desired speed is selected.See "Operational functions" on the "Control panel" pag...
Page 15 - LOAD REfERENCE
15 using the APPLiAnCe Bed sheet (single) Cotton Approximately 800g Blanket Wool Approximately 3000g Blended fabric clothes / Approximately 800g Jackets Cotton Approximately 800g Jeans / Approximately 800g Overalls Cotton Approximately 950g Ladies Pyjamas / Approximately 200g Shirts / Approximately ...
Page 16 - maintenance; AfTER wAShINg; CLEANINg ThE MAChINE
16 1. 2. 1. 2. maintenance cleAning & cAre AfTER wAShINg Turn off the water supply and pull out electricity plug after each wash. Open the washer door to prevent formation of moisture and odours. If the washing machine is left idle for a long period, drain the water in the machine and replace th...
Page 17 - wATER INLET vALvE AND INLET vALvE fILTER; LONg PERIODS Of DISUSE
17 maintenance wATER INLET vALvE AND INLET vALvE fILTER To prevent blockage to the water supply by ingress of foreign substances, clean the water inlet valve and inlet valve filter regularly. MOvINg ThE MAChINE If the machine is to be moved to a distant location, replace the transportation bolts rem...
Page 18 - DisplAy coDes; DISPLAy CODES AND SPECIAL fUNCTIONS
18 maintenance DisplAy coDes DISPLAy CODES AND SPECIAL fUNCTIONS ¬ Control panel lock function: Press the "delay" and the "Start/Pause" buttons simultaneously for 3 seconds after starting a program. It can no longer be changed by operating buttons or knobs. To unlock press the "d...
Page 19 - trouBleshooting; TROUBLEShOOTINg
19 maintenance trouBleshooting TROUBLEShOOTINg The following circumstances do not constitute problems. do not contact the Service Center until the problem has been confirmed. PROBLEM CAUSES SOLUTIONS Washing machine fails to operate. ¬ Poor connection to the power supply.¬ Power failure.¬ The washer...
Page 20 - Important Safety InformatIon
Important Safety InformatIon 20 do not use a multiple socket extension cord. A separate earthed socket is required which shall be accessible at all times.If the mains cord becomes damaged, it must be replaced by the manufacturer, its service agent or similarly qualified person with a lead of the sam...
