Haier HW60-B12866NZP - Manual

Power

Automatic Drum Washer

Operating Instructions

Models:

Please read this manual carefully before use.

Please keep this manual in a safe place for future

reference.

Specifications

This product is classified as

Class I appliance. Please pay

attention to electrical safety

during use.

The diagrams in this manual are

for illustrative purpose only. In

consideration of continuous

product improvement, please

see the actual product for the

appearance, color and

accessories which may be

inconsistent with those

described in this manual. We

hereby apologize for this.

Contents

1. Notice before Use

2. Safety Precautions

3. Precautions for Use

4. Preparations before Washing

5. Operational Procedure

6. Control Panel and Program Description

7. Display Screen Description

8. Other Functions

9. Fault Clearance

10. Cleaning/Maintenance

Technology of

variable frequency drive

Technology of

power-down memory

Technology of

automatic selection

1. Notice before Use

Please install and adjust the washer according to the instructions in this

manual so that you can use it in a correct and safer manner.

To connect the water inlet pipe

1. Select a proper water tap

2. Remove the water inlet pipe joint

The length of front end must be more than 10mm. If the

end face of water tap outlet is unsmooth, please file it

smooth to avoid water leakage.

①

Press the lower end of locking lever;

②

Hold the water inlet pipe, press

down the slider and remove the water

inlet pipe joint;

4. Connect the water inlet pipe

①

Press down the slider and insert the

water pipe into the water inlet pipe joint;

②

Hook the water inlet pipe joint with

the locking lever, then loosen the slider

until a “poop” is heard.

5. Connect to the washer

①

Ring the nut at the other end of water

inlet pipe onto the water inlet valve joint;

②

Tighten and confirm the nut of water

inlet pipe in place.
6. Check the water inlet pipe for good connection

①

Check for firm connection;

②

After installation, turn on the water tap and

check for water leakage;

③

Before every use of the washer, please check

for firm connection between the water inlet pipe

and the water tap;

④

Never forcibly bend the water inlet pipe.

Installation of the rat guard

Drain pipe

The outlet end of drain pipe must be

higher than 80cm and the highest point

must be less than 100cm. To prevent the

drain pipe from coming off, you may

secure it to its clamp at the back of washer

or to the firm holder as shown in the

figure.

It is not recommended to extend the drain

pipe. If the extension pipe exceeds 2.5m

in length, simultaneous water feeding and

drainage is likely to occur. Please contact

our After-sales Service Department for the

extension of drain pipe.

Adjustment of the feet

Be sure to adjust four feet

to level the washer before

use.

3. Install the water inlet pipe joint

①

Loosen the nut to the extent that

approximate 3-4 turns of screw thread are

exposed;

②

Loosen four screws of the water inlet pipe

joint to the extent that the joint can be ringed

onto the water tap;

③

If the water inlet pipe joint cannot be ringed

onto the water tap, please remove the bushing

and install again;

④

Turn one of screws to an approximately

proper position in advance, ring the water inlet

pipe joint onto the water tap, then evenly

tighten the remaining three screws in place,

and finally tighten the nut.

Water inlet pipe joint

Locking lever

Slider

Water inlet pipe

Wall

If the water tap is

placed against the wall,

you may turn this screw

to a proper position in

advance.

Bushing

3-4 turns

Tally

Nut

Locking lever

fig. 1

fig. 2

Note:

After finishing the adjustment of

four feet, turn the foot support

nuts to cling to the shell in order

to support the washer.

Distributor boxes

(Add a proper amount of

detergent required by washing)

Pre-wash detergent box
Main wash detergent box
Softener and bleach box

When selecting the pre-wash function or the pre-wash

program, add detergent into the pre-wash box to pre-wash

the clothes;

As for the dosage of detergent, please refer to the

instructions for detergent. Excessive detergent may result

in too many bubbles and spill as well as affect its

dissolution. Special low foaming detergent for drum

washers shall be used. When washing synthetic or wool

fabrics, be sure to use special detergent;

The level of softener or liquid detergent should not be

higher than the “MAX” mark of a distributor box.

Concentrated softener or liquid detergent should be diluted

before being added into a distributor box.

Table top

Drain pipe holder

Main control

panel

Front panel

Inner drum

Window pad

Door

Sight glass

Foot

Lower trim

Filter door

Table top

Water inlet valve

Power cord

Screw (4 pcs)

Power plug
Back cover plate

Drain pipe clamp

Drain pipe

Splash-proof plastic

plug (4 pcs)

Shell

Packaging bolts and accessories

Packaging bolts and accessories are used to

fix internal components of the washer during

transport and should be removed before using

the washer.

Unscrew packaging bolts and take

out the back-up block.

Block the bolt hole with a

splash-proof plastic plug.

Please keep such disassembled components

as packaging bolt and back-up block in a safe

place for future handling of the washer.

Accessories

Water inlet pipe assy Drain pipe holder

Rat guard

Operating

instructions

2. Safety Precautions

3. Precautions for Use

4. Preparations

Electrical safety

prompt:

Please pay attention to

electrical safety when

using the washer.

Warning sign: The

contents with this

sign involve the

safety of both the

product and user. Be

sure to strictly follow

these instructions,

otherwise the washer

may be damaged or

the user may be

injured.

Prohibitory sign: The

contents with this

sign indicate the

behaviors to be

absolutely prohibited.

Failure to follow these

instructions may

result in damage to

the washer or

personal injury.

1. The plug should be accessible after the washer is

installed in place. Do not disconnect the plug from the

socket by pulling the power cord. If the power cord needs to

be replaced, ask a qualified person or contact our

After-sales Service Department for replacement. Prevent

the power cord from being pressed by any foot and from

such problems as break-off, flattening, etc.

2. Power supply must use a separate socket, the grounding

terminal of which must be reliably grounded.

3. Such overload protective devices as proper fuse must be available at the user’s home.

And, the ammeter, wires and socket must be able to withstand the current of 10A.

1. Keep the washer away from any heat source and direct sunlight to prevent aging of plastic/rubber

parts.

1. Do not use such chemicals as flammable detergent and dry-cleaning

solvent to wash the clothes. Do not use any organic solvent or corrosive

liquid to wipe the exterior and rubber parts of the washer. Do not use any

flammable spray near the washer. In case of flammable gas leakage, do

not plug in or unplug the washer. Do not use the washer near the

environment with flammable and explosive gas or liquid such as biomass

pool, etc.

2. The washer’s door is relatively hot during heating. For the purpose of safety, keep

children away from the washer. In addition, when draining hot water, be careful to avoid

scald.
3. After unpacking the washer, do not allow children to play with the disassembled

packaging materials such as carton, plastic packaging bag and foam, etc.
4. Do not install the washer outdoors and in excessively humid environment, otherwise

the moisture on electrical components may easily cause damage to the ignition system

or other accidents. In case of inadvertent water spray onto or into the washer, only after

the washer thoroughly dries can you use it.
5. Neither place the washer directly on airproof carpet to prevent its bottom vent from

being blocked nor close up to a wall or furniture to avoid accidents. Do not use the

washer on any platform higher than the floor, otherwise it may fall off onto the floor and

be damaged.

1. Due to fluctuation of water pressure, please check all the joints of water inlet pipe, water tap and

drain pipe for firm connection before washing every time. In case of loose water pipe connection or

water leakage, please turn off the water tap and take proper measures or contact our After-sales

Service Department for reconnection. Only after such faults are cleared can you use it again.

2. Using the washer at 0

℃

and below may damage the water inlet valve and drainage system. If the

washer is stored at 0

℃

and below, be sure to move and leave it in the environment at room

temperature for 2-4 hours before use.

3. It is recommended that the washer be installed in a location with floor drainer.

4. Do not place any heavy object, heat-producing appliance and item liable to water/liquid leakage to

avoid the deformation of table top and plastic parts.

5. Do not wash such waterproof articles as raincoat, bicycle cover and down products as well as

carpet to avoid abnormal vibration or the damage to articles.

6. If a brassiere with steel wire is washed in the washer, the steel wire may bounce out. Therefore, do

not wash any brassiere with steel wire in order to protect the washer.

7. Do not put the clothes tainted with chemicals into the washer.

8. Do not open any detergent distributor box during the program operation to avoid some detergent

leaving in the box.

9. The washer’s door is equipped with self-lock safety device. Only when the washer is in safe state

(the water level is below the lower edge of sight glass, the temperature inside the drum is below 50

℃

,

the inner drum is not rotating) can you unlock the door. Never forcibly open the door before the washer

reaches the safe state to avoid damage to the door or scald. “Click” will be heard when opening the

door. It is normal and arises from the working principle of electromagnetic lock’s internal structure.

10. Cut off the water supply and power supply after finishing washing every time. Moreover, clean the

sight glass window pad interlining to prevent contaminants from tainting the clothes again or the

surface of window pad from going moldy.

11. When the washer is not in use, please keep the door slightly open to avoid unpleasant smell. Do

not cover the washer with a plastic bag to avoid moisture staying in the washer.

12. If the washer is feed water from a water tank and the difference

between the lowest height of water level in the water tank and the highest height of washer (table top)

is 0.1~0.5m, put a proper amount of detergent along with the clothes into the washer’s inner drum or

dilute the detergent and add it in the washer through corresponding detergent before washing to

prevent it from staying in the washer and affecting the washing and rinsing effect. It is not

recommended to select the prewash function and add softener in the washer in the above-mentioned

situations.

13. Washing capacity

before Washing

Check the clothes for special washing

requirements and make sure that the clothes are

suitable for washing with a washing machine and

water in order to avoid the deformation and

damage of the clothes.
For the clothes tainted with much mud

and dust, please remove them before

washing.
Wash those clothes liable to color fading

separately from other clothes.
Check pockets and remove coins,

sand, hairpin and other things

from them.

To avoid the sound from buttons,

please turn those clothes with

buttons inside out before putting

them into the washer.
Please unfold and fluff out the clothes before

putting them into the washer. Furthermore, do

not overload the washer.
When washing small articles (e.g. handkerchief,

gloves and socks, etc.) and those clothes liable

to intertwist and wear, please put them into net

bags for washing, rinsing and spinning to prevent

them from falling between the inner drum and

window pad and further avoid incomplete

washing or damage to top-grade clothes. The

weight of articles in each net bag should not

exceed 300g and the net bags should not be

washed together with those clothes not in a net

bag, otherwise the washer will not be balanced,

resulting in abnormal vibration.

Tie the ties, buckle the buttons, zip the zippers

and sew the openings.

5. Operational Procedure

Connect the water

inlet pipe and turn

on the water tap

Insert the power

plug into a power

socket.

Put down the

drain pipe.

Turn on the

power

switch.

Select the desired

program.

The “Delay” program is off by default.

To activate this program, press the

“Delay” button to make settings.

Start the selected

program.

Select the washing temperature, spinning speed,

“Delay” function, times of extra rinse and

“Intense” function, etc. as required.

Open the door, put the clothes into the washer and

close the door. Then add a proper amount of detergent

into corresponding distributor box and close it (refer to

the section of “Distributor Boxes” under “Notice before

Use” for details).

After finishing washing, the washer will automatically switch off.

Automatic Drum Washer

Operating Instructions

HW60-B12866NZP

220-240V/50H

z

Power supply

Water inlet pressure

Rated washing capacity

Rated spinning capacity

Spinning speed

Washing noise

Spinning noise

Fadeless

cotton fabric

Wool fabric

Terylen fabric/blend

fabric/chemical fiber fabric

6 kg

3kg

1kg

1200r/m
50dB (A weighted)
68dB (A weighted)

6.0kg
6.0kg

time

time

Cotton

Prewash

Synthetic

Wool

Quick

Sport Wash

Hand Wash
Heavy

Underwear

Rinse

Spin

Drain

S-D Inverter

Speed

Temp.

Delay

Strong

Start

Pause

Power

Extra Rinse

Anti-crease

Speed Up

Press and hold 2 seconds

to set door unlocked

Night Wash

HW60-B12866NZP

6.0kg

445mm

510mm

940mm

Felt

1. Remove the adhesive from the back side of the felt and paste

the felt onto the back side of the protection board in a

symmetrical position to the board’s corners;

2. Incline the washer backwards and remove fourfeet(Fig.1);

3. Place the side with dimpled grain of rat guard inwards, then

pass foot bolts through four holesand tighten them to fix the rat

guard to the shell(Fig. 2) and finally level the washer.