Page 3 - Table of Contents
Table of Contents INTRODUCTION ............................................... 2 Manual Accuracy ........................................... 2Contact Info.................................................... 2Functional Overview ...................................... 2Identification ....................
Page 4 - INTRODUCTION; Contact Info; Functional Overview
-2- G0675 10" Jointer/Planer Combo Machine INTRODUCTION We stand behind our machines. If you have any service questions, parts requests or general ques-tions about the machine, please call or write us at the location listed below. Grizzly Industrial, Inc. 1203 Lycoming Mall Circle Muncy, PA 1775...
Page 5 - Identification
G0675 10" Jointer/Planer Combo Machine -3- Figure 1. G0675 identification. A. Fence B. Fence Height Lock Knob C. Fence Tilt Lock D. Blade Guard Lock Knob E. Blade Guard F. Infeed Table G. Fence Lock Lever H. Infeed Table Adjustment Lever I. Base J. Foot K. Front Access Panel L. Planer Table Heig...
Page 6 - JoINTeR/PlANeR ComBINATIoN mACHINe; mACHINe dATA; Machine Data Sheet
-4- G0675 10" Jointer/Planer Combo Machine model G0675 JoINTeR/PlANeR ComBINATIoN mACHINe Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901 mACHINe dATA SHeeT Product Dimensions: Weight ........................................................................
Page 8 - NOTICE; Safety Instructions for Machinery
-6- G0675 10" Jointer/Planer Combo Machine For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of...
Page 10 - Additional Safety Instructions for Jointers
-8- G0675 10" Jointer/Planer Combo Machine Additional Safety Instructions for Jointers Like all machines there is danger associated with this machine. Accidents are frequently caused by lack of familiarity or failure to pay attention. Use this machine with respect and caution to lessen the possi...
Page 11 - Additional Safety Instructions for Planers
G0675 10" Jointer/Planer Combo Machine -9- Additional Safety Instructions for Planers 1. KICKBACK. "Kickback" is when the workpiece is thrown off the planer table by the force of the cutterhead. If you do not understand what kickback is, or how it occurs, DO NOT operate this machine. 2. ...
Page 12 - SECTION 2: CIRCUIT REQUIREMENTS; Power Connection Device
-10- G0675 10" Jointer/Planer Combo Machine 220V Operation Full Load Amperage Draw This machine draws the following amps under maximum load: Amp Draw ............................................. 9.9 Amps Power Supply Circuit Requirements The power supply circuit for your machine MUST be grounde...
Page 14 - Inventory; Clean Up
-12- G0675 10" Jointer/Planer Combo Machine Inventory The following is a description of the main compo-nents shipped with your machine. Lay the compo-nents out to inventory them. Note: If you can't find an item on this list, check the mounting location on the machine or examine the packaging mat...
Page 15 - Floor Load; Placement Location; Site Considerations; Base Unit
G0675 10" Jointer/Planer Combo Machine -13- Floor Load Refer to the Machine Data Sheet for the weight and footprint specifications of your machine. Some residential floors may require additional reinforcement to support both the machine and operator. Placement Location Consider existing and anti...
Page 16 - Bolting to Concrete Floors
-14- G0675 10" Jointer/Planer Combo Machine Although not required, we recommend that you mount your new machine to the floor. Because this is an optional step and floor materials may vary, floor mounting hardware is not included. To mount the base to the floor: 1. Unlatch the machine top from th...
Page 17 - Assembly
G0675 10" Jointer/Planer Combo Machine -15- Assembly Figure 12. Blade guard installed. 3. Loosen the guard lock knob, slide the blade guard into the bracket, then tighten the lock knob (see Figure 12). Blade Guard Guard Lock Knob To raise the blade guard, turn the height adjustment knob counterc...
Page 18 - Dust Collection
-16- G0675 10" Jointer/Planer Combo Machine Dust Collection To connect a dust collection hose: 1. Fit the 4" dust hose over the dust port when it is correctly positioned for jointer operation ( Figure 14) or planer operation (Figure 15), and secure in place with a hose clamp. DO NOT operate ...
Page 20 - Test Run
-18- G0675 10" Jointer/Planer Combo Machine Test Run Once the assembly is complete, test run your machine to make sure it runs properly. The test run consists of verifying the following: 1) The motor powers up and runs correctly, and 2) the cutterhead safety switch works correctly. If, during th...
Page 21 - Recommended
G0675 10" Jointer/Planer Combo Machine -19- For your convenience, the adjustments listed below have been performed at the factory and no further setup is required to operate your machine. However, because of the many variables involved with shipping and storage, some of these adjust-ments may ne...
Page 22 - SECTION 4: OPERATIONS; Basic Jointer
-20- G0675 10" Jointer/Planer Combo Machine Damage to your eyes, lungs, and ears could result from using this machine without proper protective gear. Always wear safety glasses, a respirator, and hearing protection when operating this machine. SECTION 4: OPERATIONS NOTICE If you have never used ...
Page 24 - Planer Operation Setup
-22- G0675 10" Jointer/Planer Combo Machine Basic Planer Controls This section covers the controls used during rou-tine planer operations. See Page 20 for a description of the ON/OFF switch. Table Height Handwheel: To raise or lower the planer table, rotate the table height handwheel ( Figure 25...
Page 25 - Jointer Operation Setup
G0675 10" Jointer/Planer Combo Machine -23- 7. Swing the dust chute assembly clockwise over the cutterhead, then push it down onto the infeed table until you hear a "click"—this indicates that the lock lever ( Figure 27) has secured the infeed table. The lever must engage the infeed tabl...
Page 26 - Stock Inspection
-24- G0675 10" Jointer/Planer Combo Machine Here are some rules to follow when choos- ing stock for the jointer/planer: • DO NOT joint or surface plane stock that contains knots. Injury to the operator or damage to the workpiece can occur if the knots become dislodged during the cutting operatio...
Page 27 - Squaring Stock
G0675 10" Jointer/Planer Combo Machine -25- 15 30 45 Squaring stock involves four steps performed in the order below: 1. Surface Plane on the Jointer—The con- cave face of the workpiece is surface planed flat with a jointer. Previously Jointed Edge Previously Surface Planed Face 2. Surface Plane...
Page 28 - Surface Planing
-26- G0675 10" Jointer/Planer Combo Machine The purpose of surface planing on the jointer is to make one flat face on a piece of stock (see Figures 32 –34) to prepare it for thickness planing on the planer. To surface plane on the jointer: 1. Read and understand SECTION 1: SAFETY, beginning on P...
Page 30 - Edge Jointing
-28- G0675 10" Jointer/Planer Combo Machine The purpose of edge jointing is to produce a fin-ished, flat-edged surface (see Figures 35 & 36) that is suitable for joinery or finishing. It is also a necessary step when squaring rough or warped stock. Figure 36. Illustration of edge jointing re...
Page 31 - Bevel Cutting
G0675 10" Jointer/Planer Combo Machine -29- The purpose of bevel cutting is to cut a specific angle into the edge of a workpiece (see Figures 37 & 38). The Model G0675 has preset fence stops at 45˚ outward and 90˚. If your situation requires a dif-ferent angle, the preset fence stops can be ...
Page 32 - Thickness Planer
-30- G0675 10" Jointer/Planer Combo Machine The Model G0675 planer table moves approxi-mately 1 ⁄ 16 " with one full turn of the handwheel. Each graduated mark on the table height handwheel represents 0.001" movement. To use the planer: 1. Put on safety glasses. 2. Unless your workpiece ...
Page 33 - SECTION 5: ACCESSORIES
G0675 10" Jointer/Planer Combo Machine -31- SECTION 5: ACCESSORIES ACCESSORIES Figure 40. Recommended products for protect- ing unpainted cast iron/steel parts on machinery. G5562—SLIPIT ® 1 Qt. Gel G5563—SLIPIT ® 12 oz Spray G2871—Boeshield ® T-9 12 oz Spray G2870—Boeshield ® T-9 4 oz Spray H37...
Page 34 - SECTION 6: MAINTENANCE; Schedule; Replacing Flat Drive Belt
-32- G0675 10" Jointer/Planer Combo Machine SECTION 6: MAINTENANCE Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious person- al injury. For optimum performance from your machine, fol-low this maintenance schedule and refer to any speci...
Page 35 - Adjusting/Replacing Feed Belts
G0675 10" Jointer/Planer Combo Machine -33- 6. Squeeze the flat belt in the middle to remove tension, then tighten the locking nut nearby to hold the drive pulley. 7. Remove the flat belt and install the new flat drive belt onto the pulleys. 8. Loosen the locking nut to lower the drive pul- ley....
Page 36 - Lubrication; Fence
-34- G0675 10" Jointer/Planer Combo Machine 4. Remove the flat belt and V-belt, install a new flat belt and V-belt in the same manner that you removed them. 5. Push the wheel bracket (see Figure 48) down and tighten the four cap screws, then push the infeed belt wheel down and tighten the cap sc...
Page 37 - Blade Guard Arm; Feed Roller Chain, Sprocket and; Leadscrews
G0675 10" Jointer/Planer Combo Machine -35- Figure 53. Feed roller chain, sprocket, and cogwheel lubrication locations. Cogwheels Blade Guard Arm Clean away any built up grime and debris with a rag and mineral spirits, then place 1-2 drops of light machine oil on the points shown in Figure 50 on...
Page 38 - Table Height Chain & Planer; Outfeed Table
-36- G0675 10" Jointer/Planer Combo Machine After lubricating the chain and handwheel mecha-nism, make sure the outfeed table is locked, then reverse the prior steps to reassemble the jointer/planer. Figure 56. Machine turned over for access to table height chain. To access the table height chai...
Page 39 - Troubleshooting
G0675 10" Jointer/Planer Combo Machine -37- Review the troubleshooting and procedures in this section to fix or adjust your machine if a problem devel-ops. If you need replacement parts or you are unsure of your repair skills, then feel free to call our Technical Support at (570) 546-9663. SECTI...
Page 41 - Checking Outfeed Table Parallelism
G0675 10" Jointer/Planer Combo Machine -39- Jointer Table Parallelism 4. Try to fit a 0.060" feeler gauge (or combina- tion of feeler gauges) between the cutterhead body and the bottom of the straightedge ( Figure 59). Note: Rotate the cutterhead to make sure the knives do not interfere with...
Page 44 - Inspecting Knives
-42- G0675 10" Jointer/Planer Combo Machine 5. While an assistant holds the straightedge over both tables, lift or lower the infeed table, then tighten the hex bolts and nuts as needed so there is little to no visible gap between the bottom of the straightedge and the top of the infeed table. 6....
Page 46 - Setting Fence Stops
"))" <%+,*&%?d^ciZg$EaVcZg8dbWdBVX]^cZ 6. Edh^i^dc i]Z `c^[Z \Vj\Z dkZg i]Z `c^[Z Vh h]dlc ^c Figure 65 VcY addhZc i]Z \^W Wdaih jci^ai]Z`c^[Z^hXdbeaZiZanaddhZ# 7. Jh^c\ V *bb ]Zm lgZcX]! gdiViZ i]Z _VX` hXgZlh Figure 67 ^c i]Z VXXZhh ]daZh id gV^hZdgadlZgi]Z`c^[Z#L]Zci]Z`c^[Z^hhZiXdg...
Page 48 - Spring Tension
-46- G0675 10" Jointer/Planer Combo Machine Spring Tension Feed roller spring tension must be adjusted so that feed roller pressure is uniform for planer operation. Roller spring tension will vary, depend-ing on the type of wood you plane. This is usually determined from trial-and-error. General...
Page 50 - Chain Tension
-48- G0675 10" Jointer/Planer Combo Machine 11. Place the chain back onto the feed roller sprockets, rolling it on in the same manner that you removed it in Step 7. 12. Re-install the springs and hex nuts onto both sides of the new feed rollers, tightening the nuts until they are 1 ⁄ 2 " (13...
Page 51 - Table Parallelism Inspection
G0675 10" Jointer/Planer Combo Machine -49- Planer Table Parallelism Table parallelism is critical to the operation of the machine. As such, it is essential that the table is parallel with the cutterhead (within 0.003") from side-to-side, as illustrated in Figure 80. Maximum Allowable Tolera...
Page 52 - Table Parallelism Adjustments
-50- G0675 10" Jointer/Planer Combo Machine If you do not have a Rotacator, a wood block and feeler gauges may be used, but extra care must be taken to ensure accuracy. If the table is not within the maximum allowable tolerances, it must be adjusted. 7. Move the Rotacator to the same position un...
Page 53 - Fingers
G0675 10" Jointer/Planer Combo Machine -51- 7. Locate the chain on the underside of the table. 8. Loosen the idler sprocket (see Chain Tension instructions on Page 48). 9. Mark the location of one tooth in the sprocket that you are adjusting. 10. Move the chain away from only the sprocket you wa...
Page 54 - Wiring Safety Instructions
-52- G0675 10" Jointer/Planer Combo Machine These pages are current at the time of printing. However, in the spirit of improvement, we may make chang-es to the electrical systems of future machines. Study this section carefully. If there are differences between your machine and what is shown in ...
Page 55 - Wiring Overview
G0675 10" Jointer/Planer Combo Machine -53- READ ELECTRICAL SAFETY ON PAGE 52! Wiring Overview 220 VAC 220V Single-Phase Motor Cutterhead Limit Switch Power Supply Connection Switch Assembly C B 1 2 3 A WIRING HARNESS KEY A B Motor Harness C Limit Switch Harness Power Cord 6-15 PLUG Recommended ...
Page 56 - ON/OFF Switch Assembly Wiring
-54- G0675 10" Jointer/Planer Combo Machine READ ELECTRICAL SAFETY ON PAGE 52! ON/OFF Switch Assembly Wiring View this page in color at www.grizzly.com. To Limit Switch To Power Supply ON/OFF Switch (viewed from behind) ON OFF WARNING! SHOCK HAZARD! Disconnect power before working on wiring. 1 W...
Page 57 - Components Wiring
G0675 10" Jointer/Planer Combo Machine -55- READ ELECTRICAL SAFETY ON PAGE 52! Components Wiring 21 13 14 22 To ON/OFF Switch Box, 220V Single-Phase Motor 2 2 2 1 Start Capacitor 35M 450V Z 2 U 1 U 2 Z 1 3 3 Hot Hot Ground 6-15 Plug (As Recommended) 220 VAC G Cutterhead Limit Switch PA9 PA9 PA9 ...
Page 58 - Table Breakdown
-56- G0675 10" Jointer/Planer Combo Machine 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 17 18 19 26 27 20 21 22 23 23 24 25 8 Table Breakdown SECTION 9: PARTS REF PART # DESCRIPTION REF PART # DESCRIPTION 1 P0675001 CAP SCREW M8-1.25 X 30 15 P0675015 SUPPORT BLOCK 2 P0675002 TABLE SUPPORT BLOCK 16...
Page 59 - Motor Assembly Breakdown
G0675 10" Jointer/Planer Combo Machine -57- 101 102 103 104 105 106 107 108 108-1 108-2 108-3 108-4 109 109 110 110 110 110 111 112 112 112 113 113 114 114 114 114 115 115 115 116 116 116 117 118 119 120 121 122 123 124 Motor Assembly Breakdown REF PART # DESCRIPTION REF PART # DESCRIPTION 101 P...
Page 60 - Frame Breakdown
-58- G0675 10" Jointer/Planer Combo Machine 201 201 202 203 203 204 205 206 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 Frame Breakdown REF PART # DESCRIPTION REF PART # DESCRIPTION 201 P0675201 OUTSIDE BASE PLATE 212 P0675212 FRAME 202 P0675202 REAR BASE PLATE 213 P0675213 F...
Page 61 - Fence Assembly Breakdown
G0675 10" Jointer/Planer Combo Machine -59- 301 302 302 303 303 304 305 306 307 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 Fence Assembly Breakdown REF PART # DESCRIPTION REF PART # DESCRIPTION 301 P0675301 LOCKING INSERT PLATE 313 P0675313 HEX BOLT M5-.8 X 12 302 P06753...
Page 62 - Feed Gear Assembly Breakdown
-60- G0675 10" Jointer/Planer Combo Machine 401 402 403 403 403 404 404 405 406 406 407 408 409 410 411 412 413 414 415 416 416 416 417 418 418 419 420 421 422 423 424 425 426 427 427 428 429 430 431 432 432 433 433 434 435 436 437 438 439 439 440 441 442 443 444 445 445 446 447 448 449 450 451 ...
Page 63 - Feed Gear Assembly Parts List
G0675 10" Jointer/Planer Combo Machine -61- Feed Gear Assembly Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 401 P0675401 LOCKING PLATE 427 P0675427 FLAT WASHER 6MM 402 P0675402 POSITIONING PLATE 428 P0675428 LOCK NUT M6-1 403 P0675403 FLANGE NUT M8-1.25 429 P0675429 CAP SCREW M6-1 X ...
Page 64 - Cutterhead-Feed Rollers Breakdown
-62- G0675 10" Jointer/Planer Combo Machine 501 502 503 504 505 506 507 508 508 509 509 510 510 511 511 512 513 515 516 517 517 518 518 519 519 520 521 522 523 523 524 524 525 525 526 528 529 530 531 532 533 534 535 534 534 535 536 537 538 Cutterhead-Feed Rollers Breakdown REF PART # DESCRIPTION...
Page 65 - Access Panels Breakdown
G0675 10" Jointer/Planer Combo Machine -63- 601 601 602 603 604 604 604 605 605 605 606 606 607 607 608 608 609 610 611 611 612 612 Access Panels Breakdown REF PART # DESCRIPTION REF PART # DESCRIPTION 601 P0675601 PHLP HD SCR M5-.8 X 16 607 P0675607 CAP SCREW M6-1 X 16 602 P0675602 RIGHT UPPER ...
Page 66 - Base Breakdown
-64- G0675 10" Jointer/Planer Combo Machine 701 701 702 702 703 703 705 705 706 707 707 708 708 709 710 710 710 710 711 711 711 712 712 713 713 713 714 Base Breakdown REF PART # DESCRIPTION REF PART # DESCRIPTION 701 P0675701 BASE SIDE PANEL 709 P0675709 LOCK NUT M6-1 702 P0675702 SPECIAL SCREW ...
Page 67 - Planer Table Breakdown
G0675 10" Jointer/Planer Combo Machine -65- 801 802 802 802 803 803 803 803 804 804 804 804 804 805 805 805 805 806 806 806 806 807 807 807 807 808 809 810 811 812 813 813 813 813 814 815 816 817 817 818 817 817 819 820 821 822 825 826 827 827 828 828 828 828 830 831 832 833 834 835 836 837 838 ...
Page 68 - Planer Table Parts List
-66- G0675 10" Jointer/Planer Combo Machine REF PART # DESCRIPTION REF PART # DESCRIPTION 801 P0675801 ELEVATION LEADSCREW RL 826 P0675826 TABLE ELEVATION CHAIN 802 P0675802 ELEVATION LEADSCREW 827 P0675827 PLANER TABLE GUIDE BLOCK 803 P0675803 ROLL PIN 4 X 6 828 P0675828 HEX BOLT M6-1 X 16 804 ...
Page 69 - WARRANTY CARD
C U T A LO N G D O T T E D LI N E Name _____________________________________________________________________________ Street _____________________________________________________________________________City _______________________ State _________________________ Zip _____________________Phone # _____...
Page 71 - WARRANTY AND RETURNS
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main...
