Page 3 - Table of contents
Table of contents SEcTiON 6: MAiNTENANcE ......................... 50 schedule ...................................................... 50Cleaning & protecting .................................. 50lubrication ................................................... 51tensioning/replacing V-Belts .........
Page 4 - iNTRODucTiON; contact info
-2- Model g0554z (Mfg 01/09+) iNTRODucTiON We stand behind our machines. if you have any service questions, parts requests or general ques-tions about the machine, please call or write us at the location listed below. grizzly industrial, inc. 1203 lycoming Mall Circle Muncy, pA 17756 phone: (570) 54...
Page 5 - identification
Model g0554z (Mfg 01/09+) -3- identification A B C d F h E g J K l M n Q p o Figure 1. Model g0554z identification. A. headstock (refer to Headstock controls on page 21 for details) b. spindle Mt#5 c. 3-Jaw Chuck D. steady rest E. 4-Way tool post F. halogen Work light G. Follow rest H. Coolant nozzl...
Page 6 - Machine Data Sheet
-4- Model g0554z (Mfg 01/09+) The information contained herein is deemed accurate as of 1/3/2011 and represents our most recent product specifications. Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 1 OF 3 Model G0554Z MACHINE DA...
Page 8 - NOTICE; Safety Instructions for Machinery
-6- Model g0554z (Mfg 01/09+) Safety instructions for Machinery For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to co...
Page 10 - Additional Safety for Metal Lathes
-8- Model g0554z (Mfg 01/09+) Additional Safety for Metal Lathes 1. cLEARiNG cHipS. Metal chips can eas- ily cut bare skin—even through a piece of cloth. Avoid clearing chips by hand or with a rag. use a brush or vacuum to clear metal chips. 2. cHucK KEy SAFETy. A chuck key left in the chuck can bec...
Page 11 - Operation; Full Load Amperage Draw; SEcTiON 2: ciRcuiT REQuiREMENTS; Minimum cord Requirements; power connection Device
Model g0554z (Mfg 01/09+) -9- 220v Single-phase Operation Full Load Amperage Draw this machine draws the following amps under maximum load: Amp draw .............................................. 14 Amps power Supply circuit Requirements you Must connect your machine to a grounded circuit that is ra...
Page 12 - Needed for Setup; unpacking
-10- Model g0554z (Mfg 01/09+) Wear safety glasses dur- ing the entire setup pro- cess! This machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with the controls and opera- tions before starting the machine! SEcTiON 3: SETup the following...
Page 13 - inventory
Model g0554z (Mfg 01/09+) -11- inventory the following is a description of the main com-ponents shipped with your lathe. lay the compo-nents out to inventory them. Note: If you can't find an item on this list, check the mounting location on the machine or examine the packaging materials carefully. O...
Page 14 - cleanup
-12- Model g0554z (Mfg 01/09+) The unpainted surfaces of your machine are coated with a heavy-duty rust preventative that prevents corrosion during shipment and storage. This rust preventative has been your machine's close ally and guardian since it left the factory. If your machine arrived to you f...
Page 15 - Site considerations; Weight Load; Space Allocation
Model g0554z (Mfg 01/09+) -13- Site considerations Figure 6. Minimum working clearances. 92" 38" 74" Side Door Elect. Cabinet Wall 30" 220V Single-Phase Weight Load Refer to the Machine Data Sheet for the weight of your machine. Make sure that the surface upon which the machine is pl...
Page 16 - Assembling Lathe
-14- Model g0554z (Mfg 01/09+) placing & Assembling Lathe The Model G0554Z is a heavy machine. Serious personal injury may occur if safe moving methods are not used. To be safe, get assistance and use power equipment rated for at least 3500 lbs. to move the shipping crate and machine. To place a...
Page 18 - bolting to concrete Floors; Mounting to Shop; Test Run; checking Gear Oil
-16- Model g0554z (Mfg 01/09+) you can either bolt your machine to the floor or use the included foot pads and leveling hard-ware. Because mounting your lathe to the floor with permanent hardware is an optional step and floor materials may vary, floor mounting hardware is not included. Whichever opt...
Page 22 - SEcTiON 4: OpERATiONS; Operation Overview
-20- Model g0554z (Mfg 01/09+) No list of safety guidelines can be complete. Every shop environment is different. Always consider safety first, as it applies to your individual working conditions. use this and other machinery with caution and respect. Failure to do so could result in serious per- so...
Page 23 - Headstock controls; basic controls; Main power Switch
Model g0554z (Mfg 01/09+) -21- Headstock controls A. Feed Rate & Thread charts: show the con- figurations of the change gears, levers, and knobs needed to set the rotational speed of the leadscrew or feed rod. b. Spindle Speed Levers: Configure the inter- nal headstock gearing for the various sp...
Page 24 - Gearbox controls; carriage controls & components
-22- Model g0554z (Mfg 01/09+) Gearbox controls F. Feed Lock Knob: Engages/disengages the power feed and the feed rate knobs. G. Numeric Feed Rate Knob: one of three controls for setting the feed rate. H. c-F Feed Rate Knob: one of three controls for setting the feed rate. i. STOp button: When pushe...
Page 25 - Tailstock controls
Model g0554z (Mfg 01/09+) -23- u. Apron. houses the carriage gearing and internal components. v. Longitudinal Handwheel: Moves the car- riage from side-to-side along the spindle cen-ter line in increments of 0.005" or 0.10mm. W. cross Slide Handwheel: Moves the cross slide toward and away from t...
Page 26 - Foot brake; Mounting; Removing chuck or Faceplate
-24- Model g0554z (Mfg 01/09+) Foot brake the Model g0554z lathe comes equipped with a foot brake (see Figure 22). the foot brake is intended to be used primarily as a time saving tool. the best method for using the foot brake is to turn the spindle OFF with the spindle lever, then apply even and mo...
Page 27 - Mounting chuck or Faceplate
Model g0554z (Mfg 01/09+) -25- 3. one at a time, use the spindle lock key to turn the three cam-locks counterclockwise until the marks on the cam-locks align with the single marks on the spindle nose, as shown in Figure 24. As you turn the cam-locks, they will rise slightly up from the spindle nose....
Page 29 - Mounting Workpiece
Model g0554z (Mfg 01/09+) -27- Figure 30. reversing jaws. 3. Clean away debris and oily substances from the mating surfaces of the jaws. 4. Flip each jaw 180°, then re-install the cap screws to secure top jaws, as shown in Figure 30. 3. use the chuck key to open the jaws so that the workpiece lays f...
Page 31 - Faceplate; Loading Workpiece
Model g0554z (Mfg 01/09+) -29- Faceplate the 12" faceplate included with your lathe is used when machining non-concentric workpieces or for off-center turning by clamping the workpiece to it. refer to the AccESSORiES section on page 48 for clamping options. use a minimum of three independent cla...
Page 32 - centers; Dead centers
-30- Model g0554z (Mfg 01/09+) Figure 36. Example of using a dead center with a faceplate and lathe dog. lathe dog dead Center When using a center in the spindle to mount a workpiece, the other end of the workpiece MuST be supported by a center installed in the tailstock quill to safely hold the wor...
Page 33 - using a center in the Tailstock
Model g0554z (Mfg 01/09+) -31- To mount a workpiece onto the spindle dead center: 1. disConnECt lAthE FroM poWEr! 2. thoroughly clean and dry the tapered mating surfaces of the spindle bore, tapered sleeve, and the hss Mt#3 dead center. 3. to protect these mating surfaces from rust and corrosion tha...
Page 34 - Offsetting Tailstock
-32- Model g0554z (Mfg 01/09+) Offsetting Tailstock the tailstock can be positioned offset from the spindle center line to cut a taper. When the tailstock is moved toward the operator from the center line, the machined end of the workpiece nearest the tailstock will be smaller in diameter. Conversel...
Page 35 - Tailstock Alignment
Model g0554z (Mfg 01/09+) -33- Tailstock Alignment the tailstock offset of your lathe was aligned with the spindle center line at the factory. We recommend that you take the time to ensure that the tailstock is aligned to your own desired toler-ances, especially if you have changed the offset to cut...
Page 37 - coolant System
Model g0554z (Mfg 01/09+) -35- 3. unlock the tailstock and move the tip of the bit close to, but not touching, the workpiece. 4. start spindle rotation, unlock the quill, then turn the quill handwheel clockwise to feed the bit into the workpiece. to remove the drill chuck or drill shank, put on heav...
Page 38 - Steady Rest
-36- Model g0554z (Mfg 01/09+) Steady Rest the steady rest serves as a support for long shafts (length to diameter ratio of 3:1 or greater). the steady rest can be placed anywhere along the length of the bedway. To install /use the steady rest: 1. disConnECt lAthE FroM poWEr! 2. thoroughly clean the...
Page 40 - Spindle Speed; calculating Spindle Speed
-38- Model g0554z (Mfg 01/09+) Four-Way Tool post the four-way tool post is mounted on top of the compound slide, and allows a maximum of four tools to be loaded simultaneously. the four-way tool post allows for quick indexing to new tools. this is accomplished by loosening the top handle, rotating ...
Page 42 - power Feed
-40- Model g0554z (Mfg 01/09+) power Feed power feed on the Model g0554z uses the machine to move the tooling rather than manual rotation of the handwheels. When the feed rod is engaged, the carriage or cross slide moves. threading operations use powered rotation of the longitudinal leadscrew with t...
Page 45 - Setting Feed Rate controls; A B; D O E F
Model g0554z (Mfg 01/09+) -43- NOTICE ALWAyS make sure the spindle is turned OFF and is at a complete stop before changing any gear configuration to prevent damage to the lathe gearing and voiding the warranty. Setting Feed Rate controls the feed rate lever and knobs are used with the quick change g...
Page 46 - Quick change Gears
-44- Model g0554z (Mfg 01/09+) Serious personal injury can result if you make contact with the gears, pulleys, and belt inside the left door of the lathe when the machine is run- ning or starts unexpect- edly. ALWAyS discon- nect the lathe from power before opening the left side door. Quick change G...
Page 47 - Engaging power Feed
Model g0554z (Mfg 01/09+) -45- NOTICE carriage feed rate is dependent upon the spindle speed—higher spindle speeds equal higher feed rates! pay close atten- tion to the movement of the carriage or cross slide and keep your hand poised over the power feed lever to disengage it when necessary. Failure...
Page 48 - power Feed Lever; Threading controls
-46- Model g0554z (Mfg 01/09+) NOTICE DO NOT engage the half-nut when the spindle speed is over 325 RpM. Otherwise, damage to the half-nut, leadscrew, or car- riage components may occur. the purpose of this subsection is to orient you with the controls used when threading and how to use the threadin...
Page 50 - SEcTiON 5: AccESSORiES
-48- Model g0554z (Mfg 01/09+) SEcTiON 5: AccESSORiES ACCEssoriEs T10096—Taper Attachment for Model G0554Z H5948—collet Attachment for Model G0554Z H8257—primrose Armor plate with Moly-D Machine and Way Oil 1 Quartthis superior machine and way lubricant prevents stick slip and chatter due to anti-fr...
Page 52 - SEcTiON 6: MAiNTENANcE; Schedule
-50- Model g0554z (Mfg 01/09+) SEcTiON 6: MAiNTENANcE Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious person- al injury. For optimum performance from your machine, follow this maintenance schedule and refer to any specific instructions g...
Page 53 - Lubrication; Daily Lubrication
Model g0554z (Mfg 01/09+) -51- Lubrication your lathe has numerous metal-to-metal moving parts that require proper lubrication to help ensure efficient and long-lasting operation. other than the lubrication points covered in this section, all other bearings are internally lubricated and sealed at th...
Page 56 - checking coolant Tank
-54- Model g0554z (Mfg 01/09+) Replacing v-belts 1. disConnECt lAthE FroM poWEr! 2. perform Steps 2–3 of the previous proce- dure. 3. loosen the three top adjustment hex nuts, then raise the motor up by evenly rotating the hex nuts underneath the motor mounting plate until there is enough slack in t...
Page 57 - cleaning coolant Tank
Model g0554z (Mfg 01/09+) -55- The coolant tank on this lathe is designed to store only coolant. During storage some flu- ids grow dangerous microbes, or, due to the collection of toxic metal chips in the fluid, the fluid can become a potent and extremely poisonous solution to humans and animals. us...
Page 58 - Troubleshooting
-56- Model g0554z (Mfg 01/09+) review the troubleshooting and procedures in this section to fix or adjust your machine if a problem devel-ops. if you need replacement parts or you are unsure of your repair skills, then feel free to call our technical support at (570) 546-9663. SEcTiON 7: SERvicE Tro...
Page 59 - Operation and Work Results
Model g0554z (Mfg 01/09+) -57- symptom possible Cause possible solution Bad surface finish. 1. incorrect spindle speed or feed rate.2. dull tool or poor tool selection.3. depth of cut too great.4. too much play in gibs.5. tool too high. 1. Adjust for proper spindle speed and feed rate.2. use sharp t...
Page 60 - Gib Adjustments; cross and compound Slide Gibs
-58- Model g0554z (Mfg 01/09+) cross Slide backlash Adjustment Backlash is the amount of play in a leadscrew. it is felt when turning the handwheel in one direc-tion, then turning it in the other direction. the distance the handwheel moves without moving the leadscrew or the attached component is th...
Page 61 - Tailstock Lock
Model g0554z (Mfg 01/09+) -59- Moving the gib toward the front of the slide increases pressure and moving it toward the rear of the slide decreases the pressure. loosen one gib screw a small amount, tighten the other gib screw the same amount, then test the movement of the slide. Continue this proce...
Page 63 - brake pads
Model g0554z (Mfg 01/09+) -61- brake pads When the brake pads are worn down to less than 1 ⁄ 8 " thick, they must be replaced. if the brake pads completely wear out, then metal will grind on metal and the pulley may be ruined. When replacing the brake pads, the inside of the pulley must be turne...
Page 64 - Spindle bearing
-62- Model g0554z (Mfg 01/09+) 4. remove the chuck or faceplate from the spin- dle, then open the left side door to expose the outboard end of the spindle and its end cap, as shown in Figure 94. 5. remove the three cap screws securing the end cap, then, taking care not to damage the gasket, remove t...
Page 66 - Gap Removal
-64- Model g0554z (Mfg 01/09+) Gap Removal the Model g0554z comes equipped with a gap section below the spindle that can be removed for turning large diameter parts or when using a large diameter faceplate. the gap is installed, then ground at the factory during lathe assembly for precise fit and al...
Page 67 - Wiring Safety instructions
Model g0554z (Mfg 01/09+) -65- READ ELECTRICAL SAFETY ON PAGE 65! these pages are current at the time of printing. however, in the spirit of improvement, we may make chang-es to the electrical systems of future machines. study this section carefully. if there are differences between your machine and...
Page 68 - Electrical Overview
-66- Model g0554z (Mfg 01/09+) READ ELECTRICAL SAFETY ON PAGE 65! Electrical Overview A B C E G D H J I F Halogen Lamp Electrical Cabinet Side Door Safety Switch Main Power Switch BrakeSwitch Motor Power Junction Box Coolant Pump Spindle Switches Control Panel A halogen lamp( page 69) J Control pane...
Page 69 - Electrical cabinet identification
Model g0554z (Mfg 01/09+) -67- READ ELECTRICAL SAFETY ON PAGE 65! Electrical cabinet identification Figure 100. Electrical cabinet identification. Contactor Contactor Contactor Contactor Fuses transformer terminal Block relay overload relays grounding plate
Page 70 - Electrical cabinet Wiring Diagram
-68- Model g0554z (Mfg 01/09+) READ ELECTRICAL SAFETY ON PAGE 65! Electrical cabinet Wiring Diagram A1 A2 A2 1L1 3L2 5L3 21NC 2T1 4T2 6T3 22NC KM1 Contactor Tianshui GSC1-1201 A1 A2 A2 1L1 3L2 5L3 21NC 2T1 4T2 6T3 22NC KM2 Contactor Tianshui GSC1-1201 2T1 4T2 6T3 FR1 OL Relay Juche JR29-16 95 96 98 ...
Page 71 - Halogen Lamp
Model g0554z (Mfg 01/09+) -69- READ ELECTRICAL SAFETY ON PAGE 65! elect components a Figure 103. Main power switch. A Halogen Lamp C Side Door Safety Switch NO 6 16 D Main Power Switch 5 1 7 3 0 6 2 8 4 1 GND L N N L PE PE NC C to c b Electrical Cabinet( page 68) to c G powerJunctionBox( page 70) to...
Page 72 - Brake Switch; Power Source
-70- Model g0554z (Mfg 01/09+) READ ELECTRICAL SAFETY ON PAGE 65! Electrical components (b) elect components b to c b Electrical Cabinet( page 68) to c b Electrical Cabinet ( page 68) to D Main powerswitch( page 69) Figure 104. Brake switch. E Brake Switch F Motor G Power Junction Box NO W1 V1 U1 V2...
Page 73 - Control Panel
Model g0554z (Mfg 01/09+) -71- Electrical components (c) elect components c Figure 107. Coolant pump. J Control Panel H Coolant Pump I Spindle Switches NO NO FWD REV GND 8 4 10 7 PE GND PE U21 V22 Z22 SB1 STOP SB2 JOG HL Power Lamp SA1 COOLANT ON OFF 3 1 1 3 3 0 5 4 GND C NC C NC to c b Electrical C...
Page 74 - Headstock Shifting breakdown
-72- Model g0554z (Mfg 01/09+) 1 2 3 4 5 6 7 8 9 10 11 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 142 159 3 3 3 5 9 8 7 7 14 5 9 8 14 15 17 14 15 18 20 31 21 22 29 24 25 28 26 27 38 159 20 31 30 21 2...
Page 75 - Headstock Shifting parts List
Model g0554z (Mfg 01/09+) -73- Headstock Shifting parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 P0554Z0001 OIL FILL PLUG 32 P0554Z0032 GEAR SHAFT 22T 2 P0554Z0002 HEADSTOCK COVER 33 P0554Z0033 GEAR SHAFT 17T 3 PSB06M CAP SCREW M6-1 X 25 34 P0554Z0034 END CAP 4 P0554Z0004 GASKET 35 P0554...
Page 76 - Headstock Gearing breakdown
-74- Model g0554z (Mfg 01/09+) Headstock Gearing breakdown Left Side Profile 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 99 100 101 102 103 104 105 106 107 108 109 128 157 76 82 128 82 74 74 96 96 128 A B A B C S D E
Page 77 - Headstock Gearing parts List
Model g0554z (Mfg 01/09+) -75- Headstock Gearing parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 61 PSB11M CAP SCREW M8-1.25 X 16 87 P0554Z0087 O-RING 40 X 2.65 62 P0554Z0062 SPECIAL FLAT WASHER 88 P0554Z0088 CASTING PLUG 63 P0554Z0063 PULLEY 89 P0554Z0089 END CAP 64 P0554Z0064 BRAKE BLOCK ...
Page 78 - Headstock Spindle breakdown
-76- Model g0554z (Mfg 01/09+) Headstock Spindle breakdown 74 82 89 90 95 96 103 110 111 112 113 114 115 116 117 118 120 121 122 123 124 125 126 127 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 158 119 61 134 128 133 145 133 142 128 ...
Page 79 - Headstock Spindle parts List
Model g0554z (Mfg 01/09+) -77- Headstock Spindle parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 61 PSB11M CAP SCREW M8-1.25 X 16 130 P0554Z0130 BEVELED PIN 74 PR11M EXT RETAINING RING 25MM 131 P0554Z0131 CAMLOCK 82 P0554Z0082 BALL BEARING 6204/P5 132 P0554Z0132 SPINDLE 89 P0554Z0089 END CA...
Page 80 - Gearbox Shifting breakdown
-78- Model g0554z (Mfg 01/09+) Gearbox Shifting breakdown 201 202 203 204 205 206 207 208 209 210 211 212 213 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 234 235 236 238 239 240 241 242 243 244 245 247 249 250 251 252 253 254 255 256 257 258 259 260 261 321 233 213 223 24...
Page 81 - Gearbox Shifting parts List
Model g0554z (Mfg 01/09+) -79- Gearbox Shifting parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 201 P0554Z0201 CASTING PLUG 234 P0554Z0234 SHIFT HUB 202 P0554Z0202 GEARBOX CASTING 235 PK05M KEY 4 X 4 X 10 203 P0554Z0203 TOP LEFT GEARBOX COVER 236 P0554Z0236 SHAFT 204 PFH19M FLAT HD SCR M4-....
Page 82 - Gearbox Gearing breakdown
-80- Model g0554z (Mfg 01/09+) Gearbox Gearing breakdown 250 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 322...
Page 83 - Gearbox Gearing parts List
Model g0554z (Mfg 01/09+) -81- Gearbox Gearing parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 250 PSB01M CAP SCREW M6-1 X 16 294 P0554Z0294 GEAR WASHER 262 P0554Z0262 SPECIAL FLAT WASHER 295 P0554Z0295 GEAR 16T 263 P0554Z0263 GEAR 52T 296 P0554Z0296 GEAR 26T 264 PSB02M CAP SCREW M6-1 X 20 ...
Page 84 - Apron controls
-82- Model g0554z (Mfg 01/09+) Apron controls 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 401 419 473 473 435 429 431 REF PART # DESCRIPTION REF PART # DESCRIPTION 401 PSB04M CAP SCREW M6-1 X 10 419 P0554...
Page 85 - Apron Gearing
Model g0554z (Mfg 01/09+) -83- Apron Gearing 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 474 A B A C D E B C D E REF PART # DESCRIPTION REF PART # DESCRIPTION 436 P0554Z0436 BUSHING 455 P0554Z0455...
Page 86 - Saddle & cross Slide breakdown
-84- Model g0554z (Mfg 01/09+) Saddle & cross Slide breakdown 501 502 503 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 540 541 542 543 544 545 547 548 550 551 552 553 554 555 556 557 558 559 560 561 562 563 56...
Page 87 - Saddle & cross Slide parts List
Model g0554z (Mfg 01/09+) -85- Saddle & cross Slide parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 501 P0554Z0501 CROSS SLIDE GIB 533 PS09M PHLP HD SCR M5-.8 X 10 502 P0554Z0502 GIB ADJUSTMENT SCREW 534 P0554Z0534 GRADUATED DIAL 503 PS09M PHLP HD SCR M5-.8 X 10 535 P0554Z0535 HANDWHEEL...
Page 88 - compound Slide & Tool post
-86- Model g0554z (Mfg 01/09+) compound Slide & Tool post REF PART # DESCRIPTION REF PART # DESCRIPTION 601 P0554Z0601 TOOL POST BASE 620 P0554Z0620 BEARING HOUSING 602 P0554Z0602 TOOL POST LOCK SCREW 621 PSB02M CAP SCREW M6-1 X 20 603 P0554Z0603 HANDLE HUB 622 P8103 THRUST BEARING 8103 604 P055...
Page 89 - Tailstock
Model g0554z (Mfg 01/09+) -87- Tailstock REF PART # DESCRIPTION REF PART # DESCRIPTION 651 P0554Z0651 GRADUATED DIAL 671 P0554Z0671 HANDLE 652 PSB02M CAP SCREW M6-1 X 20 672 PSB128M CAP SCREW M8-1.25 X 70 653 P0554Z0653 BEARING HOUSING 673 P0554Z0673 TAILSTOCK GIB 654 P8103 THRUST BEARING 8103 674 P...
Page 93 - bed & Shaft breakdown
Model g0554z (Mfg 01/09+) -91- bed & Shaft breakdown 904 905 906 907 908 909 910 911 912 913 914 915 916 917 918 919 920 921 922 923 924 925 926 927 928 929 930 931 932 933 934 935 936 937 938 939 941 942 943 944 945 946 947 948 949 950 951 952 953 954 955 956 957 958 959 960 961 911 919 923 940...
Page 94 - bed & Shaft parts List
-92- Model g0554z (Mfg 01/09+) bed & Shaft parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 904 P0554Z0904 THREADED STUD 933 PSS25M SET SCREW M6-1 X 20 905 P0554Z0905 ELECTRICAL BOX 934 P0554Z0934 PIN 3 X 20 906 P0554Z0906 GAP 935 P0554Z0935 CONTROL FORK 907 PSB47M CAP SCREW M10-1.5 X 40...
Page 95 - Stand & brake breakdown
Model g0554z (Mfg 01/09+) -93- Stand & brake breakdown 1001 1002 1003 1004 1005 1006 1007 1008 1009 1010 1011 1012 1013 1014 1015 1016 1017 1018 1019 1020 1021 1022 1023 1024 1025 1026 1027 1028 1029 1030 1031 1032 1033 1034 1035 1036 1037 1038 1039 1040 1041 1042 1043 1044 1045 1046 1047 1048 1...
Page 96 - Stand & brake parts List
-94- Model g0554z (Mfg 01/09+) Stand & brake parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 510 PSB02M CAP SCREW M6-1 X 20 1033 P0554Z1033 ADJUSTMENT BRACKET 562 P0554Z0562 STRAIN RELIEF 1034 PS88M PHLP HD SCR M8-1.25 X 50 563 P0554Z0563 LAMP BRACKET 1035 PN03M HEX NUT M8-1.25 1001 P05...
Page 97 - Electrical breakdown
Model g0554z (Mfg 01/09+) -95- Electrical breakdown KA1 32A 32A 328 329 331 332 1053 1054 1057 1057-1 1057-2 1057-3 1057-4 1057-5 1057-6 1101 1102 1103 1104 1105 1106 1107 1108 1109 1110 1111 1112 1113 1114 1115 1116 1117 1118 1119 1120 1053-1 1053-2 1053-3 1053-4 1053-5 1053-6 1129 1125 1126 1127 1...
Page 98 - Electrical parts List
-96- Model g0554z (Mfg 01/09+) Electrical parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 328 P0554Z0328 STOP BUTTON ASSEMBLY 1105 P0554Z1105 TERMINAL BLOCK 22-POST 329 P0554Z0329 JOG BUTTON ASSEMBLY 1106 P0554Z1106 GROUNDING BLOCK 331 P0554Z0331 POWER LAMP ASSEMBLY 1107 P0554Z1107 CORD COV...
Page 99 - Accessories
Model g0554z (Mfg 01/09+) -97- Accessories 1201 1202 1203 1204 1205 1206 1207 1208 1209 1210 1215 1217 1224 1225 1226 1227 1228 1229 1230 1231 1232 1211 1212 1213 1214 122112221223 121812191220 961 1201-1 1201-2 1233 REF PART # DESCRIPTION REF PART # DESCRIPTION 961 P0554Z0961 SHEAR PIN 5 X 40 1217 ...
Page 100 - Label placement
-98- Model g0554z (Mfg 01/09+) 1251 1252 1253 1254 1255 1256 1257 1258 1259 Label placement Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MuST maintain the original location and readability of the labels on the machine. if any label is removed or beco...
Page 101 - WARRANTY CARD
C U T A LO N G D O T T E D LI N E Name _____________________________________________________________________________ Street _____________________________________________________________________________City _______________________ State _________________________ Zip _____________________Phone # _____...
Page 103 - WARRANTy AND RETuRNS; WARRANTY AND RETURNS
WARRANTy AND RETuRNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main...
Page 104 - Buy Direct and Save with Grizzly; ORDER
Buy Direct and Save with Grizzly ® – Trusted, Proven and a Great Value! ~Since 1983~ ORDER 24 HOURS A DAY! 1-800-523-4777 Visit Our Website Today For Current Specials!
