GE RAK149P2 - User Manual - manualsarea.com

Page 2 - Specifications; WARNING; FIRE AND SHOCK HAZARD; amp maximum per terminal; IMPORTANT SAFETY INFORMATION; READ ALL INSTRUCTIONS BEFORE USING

2 49-5000517 Rev. 2 Specifications WARNING FIRE AND SHOCK HAZARD • Always turn off power at the main power supply before installing, cleaning or removing the thermostat. Failure to do so could result in electrical shock hazard. • Do not use on voltages over 30 VAC. Higher voltages will damage the th...

Page 3 - PARTS DIAGRAM; INTRODUCTION OVERVIEW

49-5000517 Rev. 2 3 PARTS DIAGRAM B G Y W C R 2 “AAA” Batteries RESET AUTO ON COOL OFF HEAT INTRODUCTION OVERVIEW Display THERMOSTAT CONTROL Auto Cool Off Heat On MODE HOLD Display Function Switch Fan Auto/On Switch Mode/Hold Switch Up/Down Buttons Up/Down Buttons Mode/Hold Switch Wiring Channel Mou...

Page 4 - INSTALLATION INSTRUCTIONS; TO INSTALL THERMOSTAT; Thermostat installation must conform to; TO R; EMOVE EXISTING THERMOSTAT

4 49-5000517 Rev. 2 INSTALLATION INSTRUCTIONS TO INSTALL THERMOSTAT IMPORTANT: Thermostat installation must conform to local and national building and electrical codes and ordinances. Note: Mount the thermostat about five feet above the floor. Do not mount the thermostat on an outside wall, in direc...

Page 5 - Function; CAUTION; Make sure exposed portion of wires

49-5000517 Rev. 2 5 INSTALLATION INSTRUCTIONS TO INSTALL THERMOSTAT (cont.) 1. Turn off power to the heating and cooling system by removing the fuse or switching off the appropriate circuit breaker. 2. Move the Function switch on the thermostat to Off . 3. Remove the cover by inserting and twisting ...

Page 6 - Connect G terminal of thermostat to Zoneline

6 49-5000517 Rev. 2 TO INSTALL THERMOSTAT (cont.) 14. Insert two “AAA” batteries into battery holder. Verify that they are oriented as shown on battery holder. 15. Replace cover on thermostat by snapping it in place. 16. Plug the unit in or turn on power to the system at the main service panel. 17. ...

Page 8 - Configuration mode

8 49-5000517 Rev. 2 Configuration mode The configuration mode is used to set the thermostat to match the heating/cooling system. This thermostat will function with up to 2-stage heatpump systems. To configure the thermostat, perform the following steps: NOTE: Operation being set will blink in the di...

Page 10 - Operating functions

10 49-5000517 Rev. 2 Operating functions Off • In this mode, the thermostat will not turn on the heating or cooling devices (manual fan can operate). • Off is also used to access Setup and Program modes. Cool • In this mode, the thermostat controls the cooling system. • Press the Mode button to ente...

Page 11 - Testing the thermostat

49-5000517 Rev. 2 11 Testing the thermostat Once the thermostat is installed, it should be thoroughly tested. CAUTION Do not use air conditioning when the outdoor temperature is below 50 degrees. This can damage the air conditioning system. Note: Before testing the thermostat, move the Fan Auto/On s...

Page 13 - Programming

49-5000517 Rev. 2 13 Programming The time and day of the week must be set for the program schedule to operate correctly. 1. Slide the Function switch to the Off position. 2. Press the Hold button in for 6 seconds. 3. Press the < or > button to adjust the time in hours. Press the Hold button on...

Page 17 - Low battery indicator; Low battery warning

49-5000517 Rev. 2 17 Low battery indicator The programmable thermostats with battery backup have a low battery warning screen. Low battery warning The thermostat will display a low battery indication. The low battery warning will be flashing until batteries are replaced.

Page 18 - Power failure Indicator; Power failure; If “; PF; ” is displayed, it means the

18 49-5000517 Rev. 2 Power failure Indicator The programmable thermostats with battery backup also will indicate a main power failure when the 24 VAC power from the room air conditioner is not present. Power failure The thermostat will display a power failure indication (“ PF ”) on the screen. Note:...

Page 19 - Notes

Page 20 - Troubleshooting tips

20 49-5000517 Rev. 2 Troubleshooting tips Problem Solution No Display Check for 24 VAC at thermostat and-batteries; display is blank when 24 VAC is not present and batteries are bad. System fan does not come on properly Verify that wiring is correct. All thermostat buttoms are inoperative Verify tha...

Page 24 - THERMOSTAT LIMITED WARRANTY; GE Appliances Will Replace:; What GE Appliances Will Not Cover:

24 49-5000517 Rev. 2 THERMOSTAT LIMITED WARRANTY For The Period Of: GE Appliances Will Replace: One Year Full Replacement of the thermostat which fails From the date of the due to a defect in materials or workmanship. original purchase For Warranty replacement, contact your distributor. What GE Appl...

GE RAK149P2 - User Manual

Table of Contents:

Summary

Other GE Thermostats Models