GE PVM2070 Manual — Free PDF Download

Page 2 - CONTENTS; General information; Installation Instructions

2 Recirculating ........................................ 19–22 Attach Mounting Plate to Wall ............19 Preparation of Top Cabinet ................19 Check Microwave Assembly ................20 Adapting Microwave Blower for Recirculation ..........................20, 21 Mount the Microwave Oven ...

Page 3 - The power cord of this appliance is equipped with a; IMPORTANT SAFETY INSTRUCTIONS

This product requires a three-prong grounded outlet.The installer must perform a ground continuity check on the power outlet box before beginning the installation to insure that the outlet box is properlygrounded. If not properly grounded, or if the outlet box does not meet electrical requirements n...

Page 4 - HOOD EXHAUST; Total Length

4 EQUIVALENT NUMBER EQUIVALENT DUCT PIECES LENGTH x USED = LENGTH Roof Cap 24 Ft. x (1) = 24 Ft. 12 Ft. Straight Duct 12 Ft. x (1) = 12 Ft. (6 ″ Round) Rectangular-to-Round 5 Ft. x (1) = 5 Ft. Transition Adaptor* Equivalent lengths of duct pieces are based on actual tests and reflect requirements fo...

Page 5 - Total Ductwork; Maximum duct length:

EQUIVALENT NUMBER EQUIVALENT DUCT PIECES LENGTH x USED = LENGTH Rectangular-to-Round 5 Ft. x ( ) = Ft. Transition Adaptor* Wall Cap 40 Ft. x ( ) = Ft. 90° Elbow 10 Ft. x ( ) = Ft. 45° Elbow 5 Ft. x ( ) = Ft. 90° Elbow 25 Ft. x ( ) = Ft. 45° Elbow 5 Ft. x ( ) = Ft. Roof Cap 24 Ft. x ( ) = Ft. Straigh...

Page 6 - If the unit is damaged in shipment,; If the unit is damaged by the customer,; If the unit is damaged by the installer; PARTS INCLUDED; HARDWARE PACKET

PART QUANTITY Top Cabinet 1 Template Rear Wall 1 Template Installation 1Instructions Separately 2Packed Grease Filters 6 PART QUANTITY Wood Screws 2 ( 1 ⁄ 4 ″ x 2 ″ ) Toggle Bolts (and 4 wing nuts) ( 3 ⁄ 16 ″ x 3 ″ ) Self-Aligning Machine 3 Screws ( 1 ⁄ 4 ″ -28 x 3 1 ⁄ 4 ″ ) Nylon Grommet 2 (for met...

Page 7 - TOOLS YOU WILL NEED; MOUNTING SPACE

7 TOOLS YOU WILL NEED # 1 and #2 Phillips screwdriver Pencil Ruler or tape measure andstraight edge Carpenter square(optional) Tin snips (for cuttingdamper, if required) Electric drill with 3 ⁄ 16 ″ , 1 ⁄ 2 ″ and 5 ⁄ 8 ″ drill bits Hammer (optional) Stud finder or Filler blocks or scrapwood pieces, ...

Page 8 - OR; FINDING THE WALL STUDS; PLACEMENT OF THE MOUNTING PLATE

8 Find the studs, using one of the following methods: A. Stud finder – a magnetic device which locates nails. OR B. Use a hammer to tap lightly across the mounting surface to find a solid sound. This will indicate a stud location. After locating the stud(s), find the center by probing the wall with ...

Page 9 - DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET; THE MICROWAVE MUST BE LEVEL.

9 DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET C. Your cabinets may have decorative trim that interfereswith the microwave installation. Remove the decorativetrim to install the microwave properly and to make itlevel. THE MICROWAVE MUST BE LEVEL. Use a level to make sure the cabinet bottom is ...

Page 10 - ALIGNING THE WALL PLATE; as the template; Set the mounting plate aside.

10 ALIGNING THE WALL PLATE Draw a vertical line on the wall at the center of the 30 ″ wide space. Use the mounting plate as the template for the rear wall. Place the mounting plate on the wall, making sure that the tabs are touching the bottom of the cabinet or the level line drawn in Step C for cab...

Page 11 - INSTALLATION TYPES

A INSTALLATION TYPES (Choose A, B or C) This microwave oven is designed for adaptation to the following three types of ventilation: A. Outside Top Exhaust (Vertical Duct)B. Outside Back Exhaust (Horizontal Duct)C. Recirculating (Non-Vented Ductless) NOTE: This microwave is shipped assembled for Outs...

Page 12 - OUTSIDE TOP EXHAUST; INSTALLATION OVERVIEW

Place the mounting plate against the wall andinsert the toggle wings into the holes in the wall to mount the plate. NOTE: Before tightening toggle bolts and wood screw, make sure the tabs on the mounting platetouch the bottom of the cabinet when pushed flush against the wall and that the plate is pr...

Page 13 - IMPORTANT: Do not grip or use handle; two full turns

13 3 MOUNT THE MICROWAVEOVEN A4. CHECK FOR PROPERDAMPER OPERATION A3. USE TOP CABINET TEMPLATEFOR PREPARATION OF TOPCABINET You need to drill holes for the top support screws, ahole large enough for the power cord to fit through,and a cutout large enough for the exhaust adaptor. A2. FOR EASIER INSTA...

Page 14 - CONNECTING DUCTWORK

14 4 Attach the microwave oven to the top cabinet. 8 7 6 Cabinet Front Cabinet Bottom Shelf Tighten the outer two screws to the top of themicrowave oven. (While tightening screws, holdthe microwave oven in place against the wall andthe top cabinet.) Filler Block Microwave Oven Top Equivalent to Dept...

Page 15 - OUTSIDE BACK EXHAUST; REMOVE EXHAUST ADAPTOR

This microwave oven is shipped assembled for topexhaust. You will need the exhaust adaptor forinstallation in the rear wall opening. To remove theexhaust adaptor from the microwave oven: Remove tape securing damper. 2 OUTSIDE BACK EXHAUST (Horizontal Duct) Lift off theblower plateand attachedadaptor...

Page 16 - USE TOP CABINET TEMPLATE

ATTACH THE MOUNTINGPLATE TO THE WALL B3. 16 USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET B4. • Read the instructions on the TOP CABINETTEMPLATE. • Tape it underneath the top cabinet. • Drill the holes, following the instructions on theTOP CABINET TEMPLATE. CAUTION: Wear safety goggles whe...

Page 17 - NOTE: The blower unit exhaust

10 9 8 5 4 7 Guide the wire down into the blower openingso it rests securely in front of the blower. Replace the blower plate in the same positionas before with the screw. Attach the exhaust adaptor to the rear of theoven by sliding it into the guides at the topcenter of the back of the oven. AFTER:...

Page 18 - TWO PEOPLE

Attach the microwave oven to the top cabinet. 18 Installation Instructions 3 MOUNT THE MICROWAVEOVEN B6. FOR EASIER INSTALLATION AND PERSONALSAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN. IMPORTANT: Do not grip or use handle during installation. NOTE: If your cabinet is metal, use...

Page 19 - RECIRCULATING

USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET C2. 19 RECIRCULATING (Non-Vented Ductless) INSTALLATION OVERVIEW C1. Attach Mounting Plate to Wall C2. Prepare Top Cabinet C3. Check Microwave Assembly C4. Adjust Blower C5. Mount the Microwave Oven C6. Install Charcoal Filter NOTE: * Make sure...

Page 20 - CHECK MICROWAVE ASSEMBLY

7 Place the blower unit back into the opening. CAUTION: Do not pull or stretch the blower unitwiring. Make sure the wires are not pinched. AFTER: Fan BladeOpenings Facing Forward 5 4 3 6 ADAPTING MICROWAVEBLOWER FOR RECIRCULATION C4. 20 NOTE: The exhaust adaptor with damper is not needed for recircu...

Page 23 - BEFORE YOU USE YOUR MICROWAVE

KEEP INSTALLATION INSTRUCTIONSFOR THE LOCAL INSPECTOR’S USE. Plug power cord into a dedicated 15- to 20-ampelectrical outlet. 7. Read the Owner’s Manual. 6. Replace house fuse or turn breaker back on. 4. Remove all packing material from the microwave oven. 2. Make sure the microwave oven has beenins...

Page 25 - GUARDE ESTAS INSTRUCCIONES.; Lea estas instrucciones completa y cuidadosamente.; IMPORTANTE –; Nota para el instalador –; ANTES DE EMPEZAR; Nota para el consumidor –; Nivel de destrezas –

LEA CUIDADOSAMENTE. GUARDE ESTAS INSTRUCCIONES. Instruccionesde instalación Lea estas instrucciones completa y cuidadosamente. • IMPORTANTE – Guarde estas instrucciones para el uso del inspector local. • IMPORTANTE – Cumpla con todos los códigos y ordenanzas gubernamentales. • Nota para el instalado...

Page 26 - CONTENIDO; Información general; Instrucciones de instalación

2 Recirculación ........................................ 19–22 Cómo adherir el plato de montaje a la pared ............................................19 Cómo preparar el gabinete superior ....19 Inspeccione la ensambladura del microondas ......................................20 Cómo adaptar el cale...

Page 28 - CAMPANA DE ESCAPE; ESCAPE SUPERIOR EXTERNO (EJEMPLO SOLAMENTE); ESCAPE POSTERIOR EXTERNO (EJEMPLO SOLAMENTE)

4 LONGITUD NÚMERO LONGITUD PARTES DEL CONDUCTO EQUIVALENTE x USADO = EQUIVALENTE Tapa del techo 24 pies x (1) = 24 pies Conducto recto de 12 pies 12 pies x (1) = 12 pies (redondo de 6 ″ ) Adaptador de transición 5 pies x (1) = 5 pies de rectángulo a redondo* La longitud de las partes de los conducto...

Page 29 - no debe sobrepasar 140 pies equivalentes.; Conexiones de escape:; No use un conducto menor de 6; Longitud máxima del conducto:; no debe; Total red de conductos =

5 La longitud de las partes de conductos equivalentes está basada en pruebas reales y reflejan los requisitos para lograr una buenaventilación con cualquier campana de escape. * IMPORTANTE: Si se usa un adaptador de transición de rectángulo a redondo, las esquinas del fondo del regulador de tiros de...

Page 30 - Si la unidad se daña durante el envío,; Si el cliente daña la unidad,; Si el instalador daña la unidad; PARTES INCLUIDAS; PAQUETE DE ELEMENTOS

6 • Si la unidad se daña durante el envío, devuelva la unidad al almacén donde la adquirió para su reparación o reemplazo. • Si el cliente daña la unidad, la reparación o el reemplazo es responsabilidad del cliente. • Si el instalador daña la unidad (si no es el cliente), la reparación o reemplazo s...

Page 32 - CÓMO COLOCAR EL PLATO DE MONTAJE

CÓMO REMOVER EL HORNOMICROONDAS DEL EMBALAJE /CÓMO REMOVER EL PLATO DE MONTAJE 8 Remueva las instrucciones de instalación, losfiltros, la bandeja de cristal, y la bolsa pequeña del equipo. No remueva el protector frontal deespuma de poliestireno del horno. Doble totalmente hacia atrás las cuatro tap...

Page 34 - CÓMO ALINEAR EL PLATO DE MONTAJE SOBRE LA PARED; como la plantilla; Aparte el plato de montaje.

10 CÓMO ALINEAR EL PLATO DE MONTAJE SOBRE LA PARED Trace una línea vertical en la pared en el centro delespacio de 30 ″ de ancho. Use el plato de montaje como la plantilla para la pared posterior. Coloque el plato de montaje en la pared,cerciorándose de que las orejillas se encuentran tocando el fon...

Page 35 - TIPOS DE INSTALACIÓN

11 A TIPOS DE INSTALACIÓN (Escoja A, B o C) Este horno microondas está diseñado para adaptarse a lossiguientes tres tipos de ventilación: A. Escape superior exterior (Conducto vertical)B. Escape posterior exterior (Conducto horizontal)C. Recirculación (Sin conducto de ventilación) NOTA: Este horno m...

Page 36 - ESCAPE SUPERIOR EXTERIOR; Para usar los tornillos basculantes:

12 Coloque el plato de montaje contra la pared einserte las alas de mariposa en los agujeros de lapared para montar el plato. NOTA: Antes de apretar los tornillos basculantes y los tornillos de madera, cerciórese de que las orejillas en elplato de montaje toquen el fondo del gabinete cuandoson empuj...

Page 37 - DOS PERSONAS INSTALEN; IMPORTANTE: No agarre ni use la manija; IMPORTANTE: Si no se usan bloques de

13 INSPECCIONE LA OPERACIÓNDEL REGULADOR DE TIRO A3. Adaptador de escape (Ausente en modelos enviados contubos de escape de recirculación) Plato delcalefactor Regulador de tiro Parte posterior del microondas • Coloque el horno microondas en su posiciónvertical, con la parte superior hacia arriba. • ...