GE Pro Elite 268 716 150 1248 - User Manual

5 WARNING: The valve and tank components of this Pro Elite unit have been assembled and tightened to the proper factory torque specifications. Over tightening may result in improper valve, probe and tank alingnment and may damage the tank O-ring (PN1010154) • Keep the media tank in the upright posit...

6 Valve Layout Analyzer Control Layout System Specifications 716 Motor Injector Screen Filter Backwash Drain Control Inlet Drain Outlet Camshaft Optical Sensor Valve Discs One Piece Valve Disc Spring Analyzer Control Injector and Cap Regenerant Tube Connection Refill Controller Time/Day Regeneration...

8 System Features Resin Tank Brine Tank 1 Cover 9 Foot , Leveling 2 Cap, Cover 10 Latch Mechanism 3 Jacket ,Resin Tank 11 Tank Collar 4 Base 12 Riser Tube 5 268 Logix PE Valve w/716 Control 13 Upper Basket 6 Resin Tank 14 Cover 7 Door, Access, Sensor 15 Shield 8 Sensors Wired Probes 1 2 3 4 5 6 7 8 ...

9 Equipment Installation Dimensions 36.9 (938.1) 60.7 (1541.6) 28.2 (715.9) 32.2 (817.5) 53.4 (1356.6) 55 (1398.1) 5.0 (127) 2.5 (63.5)

10 Typical System Layout Figure 1 Standard Basement Before Installation. Cold water lines shown. Figure 2 Softened Water Flow Diagram. Laundry Tubs Pump or Meter Hot Water Outlet Outside Faucet Outside Faucet Water Heater Bath Tub Lavatory Toilet Kitchen Floor Drain Soft Water Hard Water Outside Fau...

11 Inspection The Pro Elite system is shipped with several parts unassembled. When parts are removed from the packing, they should be inspected for damage. If any parts are damaged or missing, contact your supplier. WARNING: When handling the media tank do not turn it upside down or drop on its side...

12 Figure 5 Figure 6 Water Line & Bypass Connections A bypass valve system should be installed on all water conditioning systems. A model 1265 bypass is included with this system. The bypass valve isolates the conditioner from the water system and provides unconditioned water to service during r...

13 Drain Line Connection Note: Standard commercial practices are expressed here. Local codes may require changes to the following suggestions. Check with local authorities before installing a water conditioning system 1. The unit should be above and not more than 20 feet (6.1 m) from the drain. Use ...

15 System Operation Treated Water (Downflow) Untreated water is conditioned as it flows through the resin bed and up the riser. If the model selected at first start-up was 268r, this is a system that will refill the salt tank at the start of a regeneration cycle. When a regeneration cycle begins, th...

16 Camshaft Cycle Positions The front end of the camshaft has an indicator cup. The cup has slots in the outer edge and cycle numbers on the inside face (Figure 13). Remove the cover and look over the top of the Analyzer control to view the cycle numbers. The number at the top indicates the current ...

17 Disinfection of Water Conditioning Systems The materials of construction in the modern water conditioning system will not support bacterial growth, nor will these materials contaminate a water supply. During normal use, a conditioner may become fouled with organic matter, or in some cases with ba...

18 Displays, Icons & Cursors Note: In normal operation and during programming, only a few of the icons will actually be displayed. 1. Used to select and indicate the actual Day of the Week setting. 2. This cursor is displayed when programming the Days Override. 3. PM indicator displayed when set...

19 Programming Overview The Analyzer control includes multiple program levels that allow the Water Treatment Professional to customize the system for many water conditions. Additionally, historical data can be viewed allowing quick and easy troubleshooting. In most cases, Level I programming is all ...

20 Level l Programming - Analyzer Conditioner Note: Upon completing the Level l Programming, the Regen Icon will begin flashing indicating that a delayed regeneration will occur at the next programmed time of regeneration. If a delayed regeneration is not desired, press the REGEN Button to disable t...

22 Level lll Cycle Programming – C Values Several Level III program parameters can be adjusted to fine-tune a conditioners operation for non-standard applications. Typically these parameters will not need to be adjusted, as the default settings accommodate most applications. Contact your Water Treat...

23 Level IV Viewing History - H Values Historical information can be viewed by pressing the SET and DOWN buttons simultaneously with the Analyzer control in the home position. Release both buttons when the control displays an “H” value. Press the UP or DOWN buttons to navigate to each setting. Progr...

24 Placing 268 Water Conditioning System Into Operation (Fill Brine Tank Last) Quick Cycling the Analyzer Control It is required that the control be quick cycled to specific regeneration cycles when placing the conditioner into operation. Please review the following instructions for quick cycling th...

26 6. Fill the media tank with water. A. While the controller is in the backwash (C1) cycle, open the water supply valve very slowly to approximately the 1/4 open position. WARNING: If opened too rapidly or too far, media may be lost out of the tank into the valve or the plumbing. In the ¼ open posi...

27 Manual Regeneration Options The Analyzer control features several options that offer additional flexibility for manually regenerating the conditioner. Delayed Manual Regeneration Pressing and releasing the REGEN button starts a delayed manual regeneration. The Regeneration icon on the display wil...

28 Pro Elite Valve Exploded View & Parts List B Y PA S S B Y PA S S 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 12 21 22 23 24

31 Kits Item Part Number Description Qty. Item Part Number Description Qty. 1 4000584 Cover, 268/716 Valve 1 17 CH34199 Tank Assembly with Sensors 12 x 48 1 2 4000585 Shield, Decorative, Performa Logix Valve 1 CH34200 Tank Assembly with Sensors 10 x 44 1 3 4000586 Assembly, Cover Plate with Labels 1...

32 Brine Well Assembly Exploded View & Parts List CH15675 1 2 3 4 6 7 8 5 8 Item Part Number Description Qty. 1 CH15013-1 Brine Well w/Slots 1 2 CH15062 Safety Brine Valve 1 3 CH15070 Grommet 2 4 CH16371-60 Tubing, 3/8" x 60" Long 1 5 CH15024 Cap, Brine Well 4" Dia. (Caplug STP -4) 1...

33 Troubleshooting Analyzer Control – Error Codes & Check Salt Light Problem Possible Cause Solution ERR 1 is displayed. Program settings have been corrupted. Press any key and reprogram Level I settings. ERR 2 is displayed. The control is not a “North American” 60 Hz model. Install 60 Hz Analyz...

34 System Troubleshooting Problem Possible Cause Solution Regenerant tank overflow. a. Uncontrolled refill flow rate. b. Air Leak in regenerant line to air check. c. Drain control clogged with resin or other debris. a. Remove refill flow control to clean ball and seat . b. Check all connections in r...

©2011 Pentair Residential Filtration, LLC P/N 4001051 Rev B FE11 Pentair Residential Filtration, LLC 5730 North Glen Park RoadMilwaukee, WI 53209-4454 USA(262) 238-4400 Phone (262) 238-4402 Fax