GE PEB2060SM2SS - Installation Manual

This installation manual covers the assembly and setup of built-in microwave oven systems, including trim kits (models JX2027/JX2030) and structural supports. Key topics include safety precautions–such as proper air flow clearance and anti-tip measures–along with detailed steps for mounting brackets, ducts, and frames to ensure secure integration into cabinets or ovens. The guide also addresses leveling requirements, dimension specifications, and tool lists essential for a compliant installation.

Page 1 – Built-In Trim Kit Installation
Page 2 – Microwave Cutout and Anti-Tip Brace Installation
Page 3 – Microwave Mounting Bracket and Duct Assembly
Page 4 – Microwave Final Assembly and Leveling Procedures
Page 5 – Microwave Support Structure Assembly
Page 6 – Microwave Installation within Opening and Conduit Assembly
Page 7 – Door or Window Frame Mounting Specifications
Page 8 – Electrical Installation Kit Parts and Safety Information

Loading the manual

READ CAREFULLY.
KEEP THESE INSTRUCTIONS

Installation

Built-In Trim Kits

Instructions

JX2027 and JX2030

Read these instructions completely and carefully.

•

IMPORTANT –

Save these instructions for local inspector’s use.

•

IMPORTANT –

Observe all governing codes and ordinances.

•

Note to Installer –

Be sure to leave these instructions with the

Consumer.

•

Note to Consumer –

Keep these instructions for future reference.

•

For easier installation and personal safety, we recommend that two people
install this microwave oven.

WARNING

—

This oven must be plugged into a properly

grounded 3-hole, 120V receptacle as required by the National Electrical Code
or the Canadian Electrical Code.

❒

BEFORE YOU BEGIN

•

Do not alter or modify any part of this kit or the oven.

•

Unplug the microwave oven before attempting installation of this kit.

• Skill level

– Installation of this appliance requires basic mechanical and

electrical skills.

• Completion time

– 1-3 hours

•

Proper installation is the responsibility of the installer.

•

Product failure due to improper installation is not covered under the Warranty.

•

This kit is UL/CSA listed for installation alone or over any GE/GE Profile
single electric wall oven. Not for use adjacent to (within 2 feet of) any gas
or electric range, cooktop or oven.

•

This kit is for use on models: PEB2060DMBB, PEB2060DMWW,
PEB2060DMCC, PEB2060SMSS, JEB1860DMBB, JEB1860DMWW,
JEB1860DMCC, JEB1860SMSS, PEB206CDNBB, PEB206CSNSS,
PEB206CDNWW, JEB186CDNWW, JEB186CDNBB and JEB186CSNSS.

TOOLS YOU WILL NEED

❒

Phillips screwdriver

❒

Pencil

❒

Tape measure

❒

Awl or punch

❒

Drill with

⁄

″

bit or #35

FOR YOUR SAFETY:

WARNING –

Before beginning the

installation, switch power off at service panel and lock
the service disconnecting means to prevent power from
being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten
a prominent warning device, such as a tag, to the
service panel.

❒

Level

❒

Scissors (optional)

PART

QUANTITY

❒

Trim Frame

❒

Bottom Duct

❒

Side Duct

❒

4 mm x 12 mm

Round-Head Screws (21 required

for installation)

❒

4 mm x 14 mm

Flat-Head Screws

(4 required for
installation)

❒

Anti-Tip Brace

❒

Anti-Tip Bracket

❒

Upper Duct

❒

Top Bracket

❒

Bottom Bracket

❒

Templates

PARTS INCLUDED

NOTE:

This kit has extra screws to prevent the technician from spending extra

time locating a replacement screw in case they lose one during installation.

Questions? In the U.S., call 800.GE.CARES (800.432.2737)

or Visit our Website at:

ge.com

In Canada, call 1.800.561.3344

or Visit our Website at:

GEAppliances.ca

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Was this manual helpful?

About this manual

Brand: GE
Model: PEB2060SM2SS
Document type: Installation Manual
Language(s): English
Pages: 8
File size: 905.6 KB
Format: PDF

Other Manuals for GE PEB2060SM2SS

User Manual

Summary

Page 1 - Built-In Trim Kit Installation

Instructions, safety warnings, required tools, and parts list for installing Built-In Trim Kits JX2027 and JX2030.

Page 2 - Microwave Cutout and Anti-Tip Brace Installation

Guidance on cutout dimensions for 27" and 30" models, step-by-step installation of the anti-tip brace with dimension specifications, drilling requirements, and airflow clearance.

Page 3 - Microwave Mounting Bracket and Duct Assembly

Instructions for mounting the anti-tip bracket and bottom duct, connecting side and upper ducts, and securing the microwave centrally within the cabinet.