GE MONOGRAM ZV900 User Manual - Free PDF Download

Page 3 - Read these instructions completely and carefully.; IMPORTANT; Note to Installer; TWO PEOPLE ARE REQUIRED FOR PROPER

Safety Information 2 BEFORE YOU BEGIN Read these instructions completely and carefully. • IMPORTANT — Save these instructions for local inspector ’s use. • IMPORTANT — Observe all governing codes and ordinances. • Note to Installer — Be sure to leave these instructions with the Consumer. • Note to C...

Page 4 - INSTALLATION OPTIONS; Installation height should be measured from the; CONTENTS; The vent hood must be installed 24; to

INSTALLATION OPTIONS NOTE: Installation height should be measured from the cooking surface to the outer glass sides. This hood may be installed onto a wall and vented to the outdoors, or it can be installed for recirculatingoperation. All necessary parts for recirculatingoperation are supplied with ...

Page 5 - Installation Preparation; ADVANCE PLANNING; Wall Framing for Adequate Support; POWER SUPPLY; FOR PERSONAL SAFETY, THIS; Electrical supply

Installation Preparation 4 ADVANCE PLANNING • Determine the exact location of the vent hood. • Plan the route for venting exhaust to the outdoors. • Use the shortest and straightest duct route possible. Forsatisfactory performance, duct run should not exceed 100 ft.equivalent length for any duct con...

Page 6 - DUCT FITTINGS; Do not exceed maximum; round duct; Any home ventilation; This Hood Must Use an

DUCT FITTINGS Use this chart to computemaximum permissible lengths forduct runs to outdoors. NOTE: Do not exceed maximum permissible equivalent lengths! Maximum duct length:100 foot for 8 ″ round duct Flexible ducting: If flexible metal ducting is used, all the equivalent feet values in the table sh...

Page 7 - REMOVE THE PACKAGING

Installation Preparation REMOVE THE PACKAGING CAUTION: LIFT THE HOOD OUT OF THE BOX BY THE CENTER METAL PORTION. DO NOT LIFT BY THEGLASS SIDES. PRUDENCE : LEVEZ LA HOTTE À L’EXTÉRIEUR DE LA BOÎTE PAR LA PORTION MÉTALCENTRAL. NE LEVEZ PAS PAR LES CÔTÉS DE VERRE. CAUTION: Wear gloves to protect agains...

Page 8 - Installation Heights; Actual; DETERMINE INSTALLATION HEIGHT; CESSORY; Measure

7 Wall Mount ZV900 Installation Heights Actual *Possible Ceiling *Possible VENTED RECIRCULATING Height Installation Height Installation Height 7 ′ 11 ″ 24 ″ to 26 ″ 24 ″ to 26 ″ 8 ′ 0 ″ 24 ″ to 27 ″ 24 ″ to 27 ″ 8 ′ 1 ″ 24 ″ to 28 ″ 24 ″ to 28 ″ 8 ′ 2 ″ 24 ″ to 29 ″ 24 ″ to 29 ″ 8 ′ 3 ″ 24 ″ to 30 ″...

Page 9 - CHECK INSTALLATION HARDWARE

CHECK INSTALLATION HARDWARE Locate the hardware accessory box packed with the hood and check contents. Installation Preparation 29-7/8" 11-1/2" 12" 27-3/4" Mounting bracket 1 charcoal filter for recirculating installation 2-piece decorative duct cover (dimension shown for reference o...

Page 10 - Framing must be capable of; Install a horizontal support at least 1; The horizontal support; Installation Instructions; DUCTWORK, WIRING LOCATIONS; HOUSE WIRING LOCATION:; INSTALLATION—VENTED TO THE OUTSIDE

9 INSTALL FRAMING FOR HOODSUPPORT IMPORTANT — Framing must be capable of supporting 100 lbs. If drywall is present , mark the screw hole locations forthe top mounting brackets. Remove the template. • Cut away enough drywall to expose 2 vertical studsat the bracket location indicated on the template....

Page 11 - INSTALL DUCT BRACKET; Secure the bracket to the wall:; INSTALL MOUNTING BRACKET

Installation Instructions INSTALL DUCT BRACKET The duct bracket should be installed against theback wall and flush with the ceiling. This bracket willhold the duct cover in place at the top. Secure the bracket to the wall: • Align the marked centerline on the bracket withthe centerline on the wall. ...

Page 12 - PREPARE THE HOOD; Place the hood on a padded surface.

11 Installation Instructions PREPARE THE HOOD • Place the hood on a padded surface. • Position the motor housing at the back of the hood.Electrical connectors should face the front , withrear mounting hooks at the back. • Slip the bottom flange of the motor housing intothe side slots at the top rear...

Page 13 - CONNECT DUCTWORK; Push duct over the exhaust outlet and damper.; MOUNT THE HOOD

CONNECT DUCTWORK • Install ductwork, making connections in thedirection of airflow as illustrated. • Push duct over the exhaust outlet and damper. • Secure joints in ductwork with sheetmetal screws. • Wrap all duct joints and the flange connectionswith duct tape for an airtight seal. CAUTION: Do not...

Page 14 - CONNECT ELECTRICAL; Verify that power is turned off at the source.; If house wiring is not 2-wire

13 Installation Instructions INSTALLATION—VENTED TO THE OUTSIDE CONNECT ELECTRICAL Verify that power is turned off at the source. WARNING: If house wiring is not 2-wire with a ground wire, a ground must be provided bythe installer. When house wiring is aluminum, be sureto use U.L. approved anti-oxid...

Page 15 - INSTALL DUCT COVERS; Secure duct cover to ceiling bracket with 2 screws.; INSTALL FILTERS; Check to be sure that the main; FINALIZE INSTALLATION

INSTALL DUCT COVERS • Place the decorative ductcovers on top of the hood. NOTE: The inside (upper) duct piece has holes on oneend. The holes are intendedfor use when the hood isinstalled for recirculatingpurposes. Slide the inside endinto the outer piece; the ventholes should not be visible inthis i...

Page 16 - Determine the exact location of the vent hood.; Wiring should enter the back wall at least 22

15 Installation Instructions INSTALLATION—RECIRCULATING DUCTWORK, WIRING LOCATIONS • Determine the exact location of the vent hood. • Locate the template packed with the literature. • Measure 36 ″ from the floor to the top of the cooking surface. Add hood installation height determined on page 7. Ma...

Page 19 - SIZE AND CUT DUCT PIECE

CONNECT ELECTRICAL Verify that power is turned off at the source. WARNING: If house wiring is not 2-wire with a ground wire, a ground must be provided bythe installer. When house wiring is aluminum, besure to use U.L. approved anti-oxidant compoundand aluminum-to-copper connectors. AVERTISSEMENT : S...

Page 20 - Charcoal filter; To remove the filter, pull the filter lock downward.; Remove all tape and packing material.; The inside piece has; Duct cover

19 Installation Instructions INSTALLATION—RECIRCULATING INSTALL FILTERS IMPORTANT: Check to be sure that the main ON/OFF switch next to the motor is in the ONposition. Charcoal filter • Install the black charcoal filter into the centeropening. Secure the filter with thumbscrews oneach side. Metal fi...