GE NX-548E - Manual

GE NX-548E – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

Page 2 – External mounting; Tools and supplies needed; CAUTION
Page 3 – Wiring
Page 4 – Programming; Programming guidelines; Add transmitters; This must be; and start over at; Table 4; EXIT EXIT; Table 5
Page 5 – Transmitter options; Partition settings for keyfobs; If you press
Page 6 – Transmitter supervision windows; Delete transmitters; Testing and troubleshooting; sensor lost
Page 7 – Programming settings table
Page 11 – Supported devices
Page 12 – Specifications

Loading the manual

466-2225B July 2006

NetworX NX-548E Receiver

Installation Instructions

Contents

Introduction

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Internal mounting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

External mounting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Wiring

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

DIP switch settings

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Power up

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Programming

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Testing and troubleshooting

. . . . . . . . . . . . . . . . . . . . . . . . 6

Programming settings table

. . . . . . . . . . . . . . . . . . . . . . . . 7

Supported devices

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Specifications

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Introduction

The NX-548E Receiver adds wireless capabilities to the
NetworX line of control panels. Adding a receiver makes these
control panels compatible with NX wireless transmitters.
Only three wire connections are required for power and commu-
nication to the control panel.

Internal mounting

For internal mounting, mount the receiver inside the control
panel enclosure. Use the following installation guidelines:

• Leave at least 10 in. (25 cm) above the control panel for the

receiver’s antennas.

• Avoid areas that expose the receiver to moisture.
• Avoid areas with excessive metal or electrical wiring,

including furnaces and utility rooms.

To mount the receiver, do the following:
1.

Remove the appropriate knockouts on the top of the control
panel enclosure for the antenna shrouds.

Assemble the antenna shrouds and fit the black O-rings to
the bottom of each shroud.

Insert the shrouds into the knockout holes (

Figure 1

F igure 1.

Installing the antenna shrouds

Use the mounting screw provided to loosely install the edge
guide standoff in the lower mounting hole in the appropriate
space to the left of the control panel (

Figure 2

). Do not

tighten the mounting screw down at this time.

F igure 2.

Installing the edge guide standoff

Slide the printed circuit board into the antennae shroud
slots, after inserting wires into antennae shrouds (

Figure 3

F igure 3.

Anntennae shrouds

WARNING: To avoid possible equipment damage

or personal injury, remove power from
the control panel before making any
wiring connections to the receiver.

Antenna shroud

O-ring

Knockout hole

Enclosure top

CAUTION

You must be free of static electricity before
handling circuit boards. Touch a bare metal
surface or wear a grounding strap to
discharge yourself.

Mounting screw

Edge guide standoff

Circuit

Antennae

Enclosure

shrouds

board

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Was this manual helpful?

About this manual

Brand: GE
Model: NX-548E
Document type: Manual
Language(s): English
Pages: 12
File size: 406 KB
Format: PDF

Summary

Page 2 - External mounting; Tools and supplies needed; CAUTION

NetworX NX-548E Receiver Installation Instructions 2 6. Align the bottom of the circuit board in the edge guide standoff and twist the standoff into place ( Figure 4 ). Tighten the mounting screw ( Figure 2 ). F igure 4. Installing the circuit board External mounting This installation uses enclosure...

Page 3 - Wiring

3 9. To install the circuit board onto the back plate ( Figure 7 ), insert the antennas into the antenna shrouds, then gently slide the top of the circuit board under the two top latches, and snap the circuit board in at the bottom latch to secure it in place. F igure 7. Circuit board and back plate...

Page 4 - Programming; Programming guidelines; Add transmitters; This must be; and start over at; Table 4; EXIT EXIT; Table 5

NetworX NX-548E Receiver Installation Instructions 4 Programming This section describes how to program the units. Programming guidelines Use the following programming guidelines: • NX-4 and NX-6 control panels can have receivers added with zones that overlap those contained in the control panel. No ...