Page 2 - CONTENTS; General information; Installation Instructions
2 Recirculating ................................................. 19–22 Attach Mounting Plate to Wall ................ 19 Preparation of Top Cabinet ...................... 19 Adapting Blower for Recirculation ........................................20, 21 Mount the Oven ................................
Page 4 - HOOD EXHAUST
4 HOOD EXHAUST The following chart describes an example of one possible ductwork installation. NOTE: Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to recirculate the air back into the room, proceed to page 6. OUTSIDE TOP EXHAUST (EXAMPLE ONLY) NOTE: For ...
Page 5 - Maximum duct length:
EQUIVALENT NUMBER EQUIVALENT DUCT PIECES LENGTH x USED = LENGTH Rectangular-to-Round 5 Ft. x ( ) = Ft. Transition Adaptor* Wall Cap 40 Ft. x ( ) = Ft. 90° Elbow 10 Ft. x ( ) = Ft. 45° Elbow 5 Ft. x ( ) = Ft. 90° Elbow 25 Ft. x ( ) = Ft. 45° Elbow 5 Ft. x ( ) = Ft. Roof Cap 24 Ft. x ( ) = Ft. Straigh...
Page 6 - INSTALLATION; ADDITIONAL PARTS; HARDWARE PACKET
PART QUANTITY Top Cabinet 1 Template Rear Wall 1 Template Installation 1 Instructions Separately 2 Packed Grease Filters Charcoal 1 Filter (on some models) Exhaust 1 Adaptor Damper 1 PART QUANTITY Wood Screws 2 (¼” x 2”) Toggle Bolts (and 4 wing nuts) (¼” x 3”) Self-aligning Machine 3 Screws (¼”-28 ...
Page 7 - TOOLS YOU WILL NEED; MOUNTING SPACE
7 TOOLS YOU WILL NEED # 1 and #2 Phillips screwdriver Pencil Ruler or tape measure and straight edge Carpenter square (optional) Tin snips (for cutting damper, if required) Electric drill with 1 / 16 ” , 7 / 16 ” , 3 / 8 ” , 1 / 2 ” and 5 / 8 ” drill bits Hammer (optional) Stud finder or Filler bloc...
Page 8 - REMOVING THE OVEN FROM; PLACEMENT OF THE MOUNTING PLATE
8 Find the studs, using one of the following methods: A. Stud finder – a magnetic device which locates nails. OR B. Use a hammer to tap lightly across the mounting surface to find a solid sound. This will indicate a stud location. After locating the stud(s), find the center by probing the wall with ...
Page 9 - DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET
9 DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET C. Your cabinets may have decorative trim that interferes with the oven installation. Remove the decorative trim to install the oven properly and to make it level. THE OVEN MUST BE LEVEL. Use a level to make sure the cabinet bottom is level.If the...
Page 10 - ALIGNING THE WALL PLATE; Wear
10 ALIGNING THE WALL PLATE Draw a vertical line on the wall at the center of the 30 ” wide space. Use the mounting plate as the template for the rear wall. Place the mounting plate on the wall, making sure that the tabs are touching the bottom of the cabinet or the level line drawn in Step C for cab...
Page 11 - INSTALLATION TYPES; OUTSIDE TOP EXHAUST
A INSTALLATION TYPES (Choose A, B or C) This oven is designed for adaptation to the following three types of ventilation: A. Outside Top Exhaust (Vertical Duct)B. Outside Back Exhaust (Horizontal Duct)C. Recirculating (Non-Vented Ductless) NOTE: This oven is shipped assembled for Outside Top Exhaust...
Page 12 - ATTACH THE MOUNTING PLATE; INSTALLATION OVERVIEW
Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate. NOTE: Before tightening toggle bolts and wood screw, make sure the tabs on the mounting plate touch the bottom of the cabinet when pushed flush against the wall and that the plate is ...
Page 13 - IMPORTANT: Do not grip or use handle; Wear safety goggles
13 2 Rotate front of oven up against cabinet bottom. 1 MOUNT THE OVEN A4. ASSEMBLE AND INSTALL ADAPTOR A3. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for ...
Page 14 - ADJUST THE EXHAUST ADAPTOR
Attach the oven to the top cabinet by inserting 2 self-aligning screws through outer top cabinet holes. Turn two full turns on each screw. Be sure to keep power cord tight. Be careful not to pinch the cord, especially when mounting flush to bottom of cabinet. 3 14 5 4 Cabinet Front Cabinet Bottom Sh...
Page 15 - OUTSIDE BACK EXHAUST; ATTACH THE EXHAUST ADAPTOR TO
Attach the exhaust adaptor to the oven rear panel by sliding it into the guides at the top center of the back of the oven. OUTSIDE BACK EXHAUST (Horizontal Duct) INSTALLATION OVERVIEW B1. Prepare Rear Wall B2. Attach Exhaust Adaptor to Wall Plate B3. Attach Mounting Plate to Wall B4. Prepare Top Cab...
Page 16 - Wear safety goggles when; Be careful to avoid
16 USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET B4. • Read the instructions on the TOP CABINET TEMPLATE. • Tape it underneath the top cabinet. • Drill the holes, following the instructions on the TOP CABINET TEMPLATE. CAUTION: Wear safety goggles when drilling holes in the cabinet bottom....
Page 17 - ADAPTING BLOWER FOR; Do not pull or stretch
Place the blower unit back into the opening. Roll the blower unit 90° so that fan blade openings are facing out the back of the oven. 4 BEFORE: Fan Blade Openings Facing Up AFTER: Fan Blade Openings Facing Back 2 1 Remove the two screws that hold the blower plate and remove the screw holding the blo...
Page 18 - MOUNT THE OVEN
Attach the oven to the top cabinet by inserting 2 self-aligning screws through outer top cabinet holes. Turn two full turns on each screw. Be sure to keep power cord tight. Be careful not to pinch the cord, especially when mounting flush to bottom of cabinet. 18 Installation Instructions 2 Rotate fr...
Page 19 - RECIRCULATING
USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET C2. 19 RECIRCULATING (Non-Vented Ductless) INSTALLATION OVERVIEW C1. Attach Mounting Plate to Wall C2. Prepare Top Cabinet C3. Adjust Blower C4. Mount the Oven C5. Install Charcoal Filter • Read the instructions on the TOP CABINET TEMPLATE. • T...
Page 20 - ADAPTING BLOWER
AFTER: Fan Blade Openings Facing Forward 3 2 4 ADAPTING BLOWER FOR RECIRCULATION C3. 20 NOTE: The exhaust adaptor with damper is not needed for recirculating models. You may want to save them for possible future use. Carefully pull out the blower unit. The wires will extend far enough to allow you t...
Page 21 - IMPORTANT: Do not grip or use handle during
Place the blower unit back into the opening. CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched. 1 6 5 ADAPTING BLOWER FOR RECIRCULATION (continued) C3. 21 Replace blower plate and replace screws for blower plate and blower motor removed in Step 1. Cabinet Fr...
Page 22 - To replace the charcoal filter:
3 WHEN REPLACING THE CHARCOAL FILTER C5. MOUNT THE OVEN (continued) C4. Slide the old filter down and out to remove it. Remove plastic and other outer wrapping from the new filter and install the new filter. When properly installed, the wire mesh of the filter should be visible from the front. Repla...
Page 23 - BEFORE YOU USE YOUR OVEN
KEEP INSTALLATION INSTRUCTIONS FOR THE LOCAL INSPECTOR’S USE. Plug power cord into a dedicated 15 to 20 amp electrical outlet. 7. Read the Owner’s Manual. 6. Replace house fuse or turn breaker back on. 4. Remove all packing material from the oven. 2. Make sure the oven has been installed according t...
Page 25 - visite nuestra página en la red en:; GUARDE ESTAS INSTRUCCIONES.; Instrucciones; Horno para colocar; de instalación; encima de la estufa; IMPORTANTE –; Nota para el instalador –; ANTES DE EMPEZAR; Nota para el consumidor –; Nota para el Instalador –; Horno Microondas
¿Preguntas? Llame 800-GE-CARES (800-432-2737) o visite nuestra página en la red en: GEAppliances.com LEA CUIDADOSAMENTE. GUARDE ESTAS INSTRUCCIONES. Instrucciones Horno para colocar de instalación encima de la estufa JVM3162 JNM3163 Lea estas instrucciones completa y cuidadosamente. • IMPORTANTE – G...
Page 26 - CONTENIDO; Información general; Instrucciones de instalación
2 Recirculación ..................................................... 19–22 Cómo adherir la placa de montaje a la pared .........................................................19 Cómo preparar el gabinete superior .............19 Cómo adaptar el calefactor para la recirculación .......................
Page 28 - ESCAPE SUPERIOR EXTERNO (EJEMPLO SOLAMENTE); ESCAPE POSTERIOR EXTERNO (EJEMPLO SOLAMENTE)
4 Instrucciones de instalación CAMPANA DE ESCAPE La siguiente tabla describe un ejemplo de una posible instalación de red de conductos. NOTA: Lea las siguientes dos páginas solamente si planea ventilar el escape hacia el exterior. Si por el contrario planea recircular el aire de vuelta hacia el saló...
Page 29 - Conexiones de escape:
5 Instrucciones de instalación * IMPORTANTE: Si se usa un adaptador de transición de rectángulo a redondo, las esquinas del fondo del regulador de tiros deberán ser cortadas para que encajen, usando las tijeras de corte, para permitir el movimiento libre del regulador de tiros. NOTA: Si usted necesi...
Page 30 - INSTALACIÓN; PARTES ADICIONALES; PAQUETE DE ELEMENTOS
PARTE CANTIDAD Plantilla para 1 el gabinete superior Plantilla para 1 la pared posterior Instrucciones 1 de instalación Filtros de 2 grasa empacados por separado Filtro de 1 carbonilla (en algunos modelos) Adaptador del 1 escape Regulador 1 de tiro PARTE CANTIDAD Tornillos de madera 2 (¼” x 2”) Torn...
Page 32 - CÓMO COLOCAR EL PLATO DE MONTAJE
8 Instrucciones de instalación Encuentre los postes, usando uno de los métodos siguientes: A. Use un detector de postes – un dispositivo magnético que localiza clavos. O B. Use un martillo para golpear ligeramente a través de la superficie de montaje hasta encontrar un sonido sólido. Esto indicará q...
Page 33 - C. CÓMO DETERMINAR LA LOCALIZACIÓN DEL PLATO DE MONTAJE DEBAJO DE
9 Instrucciones de instalación C. CÓMO DETERMINAR LA LOCALIZACIÓN DEL PLATO DE MONTAJE DEBAJO DE SU GABINETE C. Sus gabinetes podrían tener marcos de decoración que interfieran con la instalación del horno. Remueva los marcos decorativos para instalar el horno apropiadamente y para hacer que quede n...
Page 34 - CÓMO ALINEAR EL PLATO DE MONTAJE SOBRE LA PARED; Use
10 Instrucciones de instalación CÓMO ALINEAR EL PLATO DE MONTAJE SOBRE LA PARED Trace una línea vertical en la pared en el centro del espacio de 30” de ancho. Use el plato de montaje como la plantilla para la pared posterior. Coloque el plato de montaje en la pared, cerciorándose de que las orejilla...
Page 35 - TIPOS DE INSTALACIÓN; ESCAPE SUPERIOR EXTERIOR; Ver página 12
A TIPOS DE INSTALACIÓN (Escoja A, B o C) Este horno está diseñado para adaptarse a los siguientes tres tipos de ventilación: A. Escape superior exterior (Conducto vertical)B. Escape posterior exterior (Conducto horizontal)C. Recirculación (Sin conducto de ventilación) NOTA: Este horno es enviado ya ...
Page 36 - Tenga cuidado; CÓMO ADHERIR LA PLACA; PERSPECTIVA GENERAL DE LA; Para usar los tornillos basculantes:
12 Instrucciones de instalación Coloque el plato de montaje contra la pared e inserte las alas de mariposa en los agujeros de la pared para montar el plato. NOTA: Antes de apretar los tornillos basculantes y los tornillos de madera, cerciórese de que las orejillas en el plato de montaje toquen el fo...
Page 37 - Use gafas de
13 Instrucciones de instalación 2 Gire el frente del horno contra el fondo del gabinete. 1 CÓMO MONTAR EL HORNO A4. ENSAMBLAJE E INSTALACIÓN DEL ADAPTADOR A3. USE LA PLANTILLA DEL GABINETE SUPERIOR PARA LA PREPARACIÓN DEL GABINETE Deberá perforar agujeros para los tornillos de apoyo superiores, un a...
Page 38 - CÓMO MONTAR EL HORNO
4 Pegue el horno a la parte superior del gabinete insertando dos tornillos autoalineables a través de los agujeros exteriores superiores del horno. Gire dos vueltas completas en cada tornillo. Cerciórese de mantener el cable eléctrico estirado. Tenga cuidado de no pellizcar el cable, especialmente c...
Page 40 - CÓMO ADHERIR EL PLATO DE
16 USE LA PLANTILLA DEL GABINETE SUPERIOR PARA PREPARAR EL GABINETE SUPERIOR B4. • Lea las instrucciones sobre la PLANTILLA DEL GABINETE SUPERIOR. • Péguela debajo del gabinete superior. • Taladre los agujeros, siguiendo las instrucciones en la PLANTILLA DEL GABINETE SUPERIOR. PRECAUCIÓN: Use gafas ...
Page 41 - CÓMO ADAPTAR EL CALEFACTOR PARA; No tire ni estire
Coloque la unidad del calefactor de nuevo en la abertura. Ruede la unidad del calefactor 90º de forma tal que las aberturas de la paleta del ventilador estén orientadas hacia la parte posterior del horno. 4 ANTES: Las aberturas del ventilador están orientadas hacia arriba DESPUES: Las aberturas de l...
Page 42 - MONTAJE DEL HORNO
Pegue el horno a la parte superior del gabinete insertando dos tornillos autoalineables a través de los agujeros exteriores superiores del horno. Gire dos vueltas completas en cada tornillo. Cerciórese de mantener el cable eléctrico estirado. Tenga cuidado de no pellizcar el cable, especialmente cua...
Page 45 - CÓMO ADAPTAR EL CALEFACTOR
Coloque la unidad del calefactor de nuevo en la abertura. PRECAUCIÓN: No tire ni estire los cables del calefactor. Cerciórese de que los alambres no están pellizcados. 1 6 5 CÓMO ADAPTAR EL CALEFACTOR PARA LA RECIRCULACIÓN (continuación) C3. 21 Reinstale el plato del calefactor y los tornillos del p...
Page 46 - Para reemplazar el filtro de carbonilla:; QUANDO REEMPLACE EL FILTRO
Si el modelo no tiene ventilación al exterior, el aire recirculará por un filtro de carbonilla desechable que ayuda a eliminar el humo y los olores. El filtro de carbonilla debe reemplazarse cuando esté visiblemente sucio o decolorado (por lo general, después de 6 a 12 meses, según el uso que se le ...