GE JB860SJ5SS - Installation Manual
An Installation Manual for freestanding electric ranges covers essential setup procedures, including safety precautions, clearance requirements, and electrical wiring–such as grounding rules, conduit installation, and terminal connections for both 3-wire and 4-wire configurations. The guide also addresses leveling the unit, anti-tip device placement, and model-specific adjustments (e.g., for single or double ovens with storage features). Key topics include electrical safety compliance, wiring diagrams, and final verification steps to ensure proper function and adherence to building codes.
Table of Contents:
- Page 1 – Installation Requirements and Measurements for Electric Ranges
- Page 2 – Electrical Wiring and Component Installation Procedures
- Page 3 – Wiring Connections for Power Cord and Conduit
- Page 4 – Range Leveling and Stability Installation
- Page 5 – Dimensional Requirements for Freestanding Range Installation
- Page 6 – Power and Control Cable Installation
- Page 7 – Wiring Procedures for Terminal Block Connections
- Page 8 – Final Installation Verification and Safety Checklist
2
PREPARE THE OPENING (FOR INDOOR USE ONLY)
See illustrations for all rough-in and spacing dimensions. The range may be placed with 0”
clearance (flush) at the back wall and side walls of the cabinet.
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•
IMPORTANT
—
Save these
instructions for local inspector’s use.
•
IMPORTANT
—
Observe all
governing codes and ordinances.
•
Note to Installer –
Be sure to leave these
instructions with Consumer.
•
Note to Consumer –
Keep these
instructions for future reference.
•
Skill level –
Installation of this appliance
requires basic mechanical skills and
advanced electrical skills.
•
Proper installation is the responsibility of the
installer.
•
Product failure due to improper installation
is not covered under Warranty.
Installation Instructions
Free-Standing Electric Ranges
MATERIALS YOU MAY NEED
TOOLS YOU WILL NEED
(UL Listed 40 AMP)
4-Wire Cord 4’ long OR
3-Wire Cord 4’ long
Squeeze Connector
(For Conduit
Installations Only)
Drill with 1/8” Bit
Safety Glasses
Adjustable Wrench
Level
Tin Snips
Tape Measure
Pliers
1/4” Nut Driver
1
REMOVE PACKAGING MATERIALS:
Failure to remove packaging
materials could result in damage to the appliance. Remove all packing parts from oven,
racks, heating elements and drawer. Also, remove protective film and labels on the outer
door, cooktop and control panel.
FOR YOUR SAFETY:
WARNING
Before beginning
the installation, switch power off at
service panel and lock the service
disconnecting means to prevent power
from being switched on accidentally.
When the service disconnecting
means cannot be locked, securely
fasten a prominent warning device,
such as a tag, to the service panel.
If you did not receive an anti-tip bracket with your
purchase, call 1.800.626.8774 to receive one at no
cost. (In Canada, call 1.800.561.3344.) For installation
instructions of the bracket,
visit: www.GEAppliances.com.
(In Canada, www.GEAppliances.ca.)
Anti-Tip Bracket
Kit Included
NOTE:
Use a 4’ power cord to prevent interference with
the storage drawer. Power cords 4
1
»
2
’ to 6’ long may
have to be dressed to allow for proper drawer closing.
MINIMUM DIMENSIONS BETWEEN COOKTOP,
WALLS AND ABOVE THE COOKTOP:
A. Make sure the wall covering, countertop, flooring and
cabinets around the range can withstand the heat (up
to 200°F) generated by the range.
B. Allow 30” minimum clearance between surface units
and bottom of unprotected wood or metal cabinet, or
allow a 24” minimum when bottom of wood or metal
cabinet is protected by no less than 1/4” thick flame
retardant millboard covered with not less than No 28
MSG sheet metal, (.015”), .015” thick stainless steel,
.024” aluminum or .020” copper.
C. This appliance has been approved for 0” spacing to
adjacent surfaces above the cooktop. However, a 6”
minimum spacing to surfaces less than 15” above the cooktop and adjacent
cabinet is recommended to reduce exposure to steam, grease splatter and heat.
To reduce the risk of burns or fire when reaching over hot surface elements, cabinet storage space
above the cooktop should be avoided. If cabinet storage space is to be provided above
the cooktop, the risk can be reduced by installing a range hood that projects at least 5” beyond
the front of the cabinets. Cabinets installed above the cooktop must be no deeper than 16”.
• A child or adult can tip the range and be killed.
• Install the anti-tip bracket to the wall or floor.
• Engage the range to the anti-tip bracket by sliding the
range back such that the foot is engaged.
• Re-engage the anti-tip bracket if the range is moved.
• Failure to do so can result in death or serious burns
to children or adults.
Tip-Over Hazard
WARNING
2
1
»
2
”
2
1
»
2
”
7
1
»
2
”
25”
47”
25
3
»
8
”
7”
14
1
»
2
”
On models with baking
or warming drawers,
electrical outlet must
not be in this area.
3
1
»
4
”
3
1
»
4
”
7
3
»
4
”
23
1
»
2
”
47”
29
7
»
8
”
25
3
»
8
”
45”
36”
SINGLE OVEN
DOUBLE OVEN
Acceptable electrical outlet area.
Orient electrical receptacle so the
length is parallel to floor.
30”
47
5
»
8
”
30”
29
7
»
8
”
*
*
3”
4”
A
NOTE C
B
A
C
Both
Sides
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Was this manual helpful?
About this manual
- Brand
- GE
- Model
- JB860SJ5SS
- Document type
- Installation Manual
- Language(s)
- English, Spanish
- Pages
- 8
- File size
- 500.8 KB
- Format
Summary
Instructions for installing free-standing electric ranges, including safety precautions, required materials, tools, and specific measurements for the installation opening and electrical outlet placement.
Detailed instructions for installing power cords and conduits, grounding rules, wiring specifications, removal of covers, cord/conduit installation, and reassembly procedures.
Step-by-step instructions and diagrams detailing the connection procedures for 3-wire and 4-wire power cord and conduit installations to terminal blocks and ground plates.
