GE GTD84GCSN1WS - Installation Manual

GE GTD84GCSN1WS

GE GTD84GCSN1WS – Installation Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
Page: / 20

Table of Contents:

  • Page 2 – Installation Instructions; Tilt the dryer sideways and remove the foam; UNPACKING YOUR DRYER; Side View
  • Page 3 – Keep flammable materials and vapors, such as; WARNING
  • Page 4 – WATER SUPPLY REQUIREMENTS; washer’s; CONNECTING INLET HOSES
  • Page 5 – MATERIALS YOU WILL NEED
  • Page 6 – GAS REQUIREMENTS; DOES NOT
  • Page 7 – CONNECTING THE DRYER TO
  • Page 9 – Before making the electrical connection, turn off; NEVER LEAVE
  • Page 10 – CONNECTING AN ELECTRIC DRYER
  • Page 11 – CONNECTING DRYER USING; CONNECTING DRYER USING 4-WIRE; NEVER LEAVE THE COVER OFF OF THE; If required, by local code, install external ground
  • Page 13 – The correct exhaust installation is YOUR; EXHAUST LENGTH; DO NOT; DO
  • Page 14 – BEFORE YOU BEGIN; RECOMMENDED CONFIGURATION; EXHAUST SYSTEM CHECKLIST; HOOD OR WALL CAP
  • Page 15 – SIDE OR BOTTOM VENTING; shock or lacerations.; Be sure not to pull or damage the electrical
  • Page 16 – FINAL SETUP; LEVEL THE DRYER; Power; NEVER LEAVE THE BACK OPENING WITHOUT; Service personnel – DO NOT
  • Page 17 – ABOUT REVERSING THE DOOR; Before you start; Choose the; REVERSING THE DOOR; instructions; REVERSING THE DOOR - SOLID DOOR
  • Page 19 – REVERSING THE DOOR - GLASS
Loading the manual

- Risk of Fire

• Clothes dryer installation must be performed by a

qualified installer.

• Install the clothes dryer according to these instructions

and local codes.

•

DO NOT

install a clothes dryer with flexible plastic venting

materials. If flexible metal (semi-rigid or foil-type) duct is

installed, it must be UL-listed and installed in accordance

with the instructions found in “Connecting the Dryer

to House Vent” later in this manual. Flexible venting

materials are known to collapse, be easily crushed and

trap lint. These conditions will obstruct dryer airflow and

increase the risk of fire.

•

DO NOT

install or store this appliance in any location

where it could be exposed to water or weather.

• To reduce the risk of severe injury or death, follow all

installation instructions.

• Save these instructions. (Installers: Be sure to leave

these instructions with the customer.)

In the Commonwealth of Massachusetts,

the following installation instructions apply:

• Installation must be performed by a qualified or

licensed contractor, plumber, or gasfitter qualified

or licensed by the State.

• If using a ball valve, it shall be a T-handle type.
• A flexible gas connector, when used, must not

exceed 4 feet.

FOR GAS DRYERS ONLY

BEFORE YOU BEGIN

Read these instructions completely and carefully.

IMPORTANT

–

Save these instructions for local electrical

inspector’s use.

IMPORTANT

–

Observe all governing codes and

ordinances.
• Install the clothes dryer according to the manufacturer’s

instructions and local codes.

• Note to Installer –

Be sure to leave these instructions

with the Consumer.

• Note to Consumer –

Keep these instructions for future

reference.

• Clothes dryer installation must be performed by a qualified

installer.

• This dryer

must

be exhausted to the outdoors.

• Before the old dryer is removed from service or discarded,

remove the dryer door.

• Do not allow children on or in the appliance. Close

supervision of children is necessary when the appliance

is used near children.

• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not

covered under the Warranty.

• Install the dryer where the temperature is above 50°F for

satisfactory operation of the dryer control system.

• Remove and discard existing plastic or metal foil duct

and replace with UL-listed duct.

• Service information and the wiring diagram are located

in the control console.

05-19 GEA

31-3000199

Questions? Call GE Appliances at 800.GE.CARES (800.432.2737) or visit our Web site at: GEAppliances.com

Dryers

Installation

Instructions

WARNING

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Was this manual helpful?

About this manual

Brand
GE
Model
GTD84GCSN1WS
Document type
Installation Manual
Language(s)
English
Pages
20
File size
5.8 MB
Format
PDF

Summary

Page 2 - Installation Instructions; Tilt the dryer sideways and remove the foam; UNPACKING YOUR DRYER; Side View

Installation Instructions 2 Tilt the dryer sideways and remove the foam shipping pads by pulling at the sides and breaking them away from the dryer legs. Be sure to remove all of the foam pieces around the legs.Remove the bag containing the literature. UNPACKING YOUR DRYER ROUGH-IN DIMENSIONS GE App...

Page 3 - Keep flammable materials and vapors, such as; WARNING

Installation Instructions MOBILE OR MANUFACTURED HOME INSTALLATION • Installation MUST conform to the MANUFACTURED HOME CONSTRUCTION AND SAFETY STANDARD, TITLE 24, PART 3280 or STANDARD FOR MOBILE HOMES CAN/CSA-Z240 MH, or, when such standards are not applicable, with AMERICAN NATIONAL STANDARD FOR ...

Page 4 - WATER SUPPLY REQUIREMENTS; washer’s; CONNECTING INLET HOSES

Installation Instructions 4 CONNECTING INLET HOSES (for steam dryer models only) CONNECTING INLET HOSES (cont.) 7 . Using pliers, tighten all the couplings with an additional two–thirds turn. NOTE: Do not overtighten. Damage to the couplings may result. 8. Turn the water faucet on. 9 . Check for lea...

Ask a question

Up to 3 photos. Max 5 MB each. Formats: JPG, JPEG, PNG, WebP.

Related manuals

Popular GE Other

More GE Other models