Fujitsu FC9660RA12 - Manual

2 your telephone sets and other telecommunication devices. Thesecond method requires a splitter and is explained in Chapter4. If it is determined that a splitter is required, it will beinstalled by your DSL service provider. Whether microfilters or a splitter is installed, a DSL modemallows telephon...

3 1.3 DSL Modem Package Contents The DSL Modem package contains: DSL Modem RJ-45 Ethernet Crossover Cable RJ-11 to RJ-11 Line Cord Power Supply Convertor Microfilter (splitterless application) Two-Outlet Modular Adapter (splitterless operation) Figure 1-1: DSL Modem Package Contents m0437.2 Part # F...

4 2 DSL Modem Description 2.1 DSL Front Panel Figure 2-1 depicts the DSL modem LEDs. The following table describes the LEDs on the DSL modem. Figure 2-1: DSL Modem LEDs Modem Lights On Description POWER Indicates power is applied to the modem MODEM Indicates a link with the phone company equipment D...

5 2.2 DSL Rear Panel Figure 2-2 depicts the rear connections of the DSL modem. The following table lists and describes the functions of theitems located on the rear of the modem. Figure 2-2: DSL Rear Panel Connections Connector Description POWER Multipin connection for the power supply wall transfor...

6 2.3 DSL Bottom Panel The DSL modem can be installed on a desktop, shelf, ormounted on a wall. Wall mounting requires two wall anchors(not included). The holes located on the bottom of the modemare used to hang the unit on the wall anchors. Figure 2-3 shows the bottom of the DSL modem. Figure 2-3: ...

7 3 Installing the Splitterless DSL Modem 3.1 Overview The procedures in this chapter apply to those customers whoinstall their own microfilter-to-phone connections. If a DSLtechnician is performing the wiring, proceed to Section 5, Powering the Modem . Note: Do not install a microfilter on the DSL ...

8 3.2 Microfilter Installation Procedures Installing microfilters should not require any new insidewiring. Existing wired RJ-11 telephone jacks are all that isrequired to complete this installation. See Figure 3-1 for an installation diagram. 1. Start in the location where you want to install your D...

9 6. Connect the telephone RJ-11 cord connector into the microfilter RJ-11 PHONE slot. 7. Connect all remaining telephone devices to a microfilter. See Figure 3-2 , 3-3 , 3-4 for examples. Figure 3-2: Telephone Set Application Figure 3-3: Answering Machine Application Figure 3-4: Fax Application m12...

10 8. For an Ethernet connection, connect one end of the Ethernet (crossover) cable, part number FC9660CB23,to the RJ-45 slot titled DATA on the back of the DSLmodem and connect the other end of the Ethernet cableto the network interface card in back of the computer.See Figure 3-5 for examples. Note...

11 3.3 Connecting Multiple PCs to an Ethernet Local Area Network (LAN) using the Splitterless Application Note: Connecting multiple PCs to the internet via a single DSLmodem may require multiple IP addresses. Call your local ISPprovider for details. Figure 3-6 is an example of a residential, small o...

12 4 Installing the DSL Modem with Splitter 4.1 Connecting the Inside Wire and Modem Cables CAUTION: Improper inside wiring can cause ADSL service interruption. Interiorhome wire is the homeowner’s responsibility. Figure 4-1 represents a standard wiring scheme. Not all homes will follow this convent...

16 5 Powering the Modem WARNING: When installing the DSL modem power supply unit, be sure to first insertthe power supply connector into the rear of the DSL modem beforeplugging the unit into a powered 110V AC wall outlet. To apply power to the DSL modem, perform the followingsteps: 1. Insert the po...

17 Figure 5-1: Turn-Up Flow Chart m0495.fh8 4 POWER DSL Modem Turn-up Flow Chart Modem is powered on. For a few seconds,the modem is performing several self-tests. Modem is idle. Modem is checking for presenceof the DSL local service provider. If the modemstays in this state for more than 10 minutes...