Frigidaire FPRU19F8WF3 - Installation Manual

P/N: A21568903

I n s t a l l a t i o n I n s t r u c t i o n s f o r

S i n g l e - D o o r F re eze r a n d R e f r i g e ra to r P a i r i n g K i t

We recommend an authorized service technician install the pairing kit.

Components

Contains:

Part

Part number

Qty.

A Heater Assembly:

12V 10W 14.4

Ω

, Aluminum foil

sandwich, PVC wire insulation, Acrylic adhesive, 5.5 mm x

2.5 mm barrel connector spliced in heater assembly

A21442902

1

B AC Power Cable:

Ultra low profile 6ft NEMA 5-15P to C13

Angled Power Cord, 3 pin plug

A21545701

1

C Power Supply:

12V 60W AC/DC Adapter, 5.5mm x 2.5mm

x 10.5 mm plug connector

A21545401

1

D Double-sided Tape

316237303

2

E

Clips

218990901

6

Recommended Tool:

G l ove s

IMPORTANT

Make sure there are two separate dedicated grounding-type duplex wall outlets for

the freezer and the refrigerator as specified in

IMPORTANT SAFETY INFORMATION

in the Use & Care Manual.

Installation

Before cleaning your appliance, turn off power to your appliance by unplugging the power

cord from the electrical outlet. Wipe down both sides of the refrigerator and the freezer.



NOTE

Never use CHLORIDE to clean stainless steel. Clean stainless-steel front and handles

with non-abrasive soapy water and a dishcloth. Rinse with clean water and a soft

cloth. Wipe stubborn spots with an ammonia-soaked paper towel, and rinse. Use a

non-abrasive stainless-steel cleaner, such as

Frigidaire

Ready

Clean™ Stainless Steel

Cleaner

found on Frigidaire.com. Always follow the manufacturer’s instruction



NOTE

Always, clean, wipe and dry with the grain to prevent scratching. Wash the rest of

the cabinet with warm water and mild liquid detergent. Rinse well and wipe dry with

a clean soft cloth.

CAUTION

The cabinet is heavy.

We recommend two people

to lift or move the cabinet.

1. If you use the dual installation trim kit,

install the levelers on the units before

installing the heater (Fig. 1).

NOTE:

Please refer to

Single-Door

All Refrigerator and All Freezer Trim Kit

Installation

Instruction.

Fig. 1

2. Peel off the paper backing from the

first heater.

3. Adhere the first heater to the upper

right side of the left-side unit (0.5in

from the top and 0.5" from the back

wall) so the harnesses come out

at the bottom.

NOTE:

Make sure you adhere the heater

completely with no air pockets (Fig. 2A).
4. Peel off the paper backing from the

second heater.

5. Adhere the second heater to the

lower left side of the right-side unit

(0.5" from the bottom and 0.5" from

the back wall) so the harnesses come

out at the top.

NOTE:

Make sure you adhere the heater

completely with no air pockets (Fig. 2B).

Avoid:

Both heaters on the Freezer
Both heaters on the Refrigerator
Both heaters on the top
Both heaters on the bottom
Both heaters in the center

6. Plug in the connector of the two

Heaters

A

into the

Power Supply

C

(Fig. 3).

NOTE:

Confirm the power supply fits into

the cutout when placed on top of the unit.

on top of the unit, adhere it vertically

on the back wall of the unit and make

sure the connection of the 3-prong

connector to the power supply is

facing down (Fig. 5).

NOTE:

You cannot feel the

heater temperature.

Fig. 5

9 Push the two units together.

10. Use the clips provided to hold the

excess power cords to the back of the

units such that all wires are away from

the floor (Fig. 6).

NOTE:

Make sure the harnesses and cables

are cleared off the floor before the units are

pushed back in place. This will prevent any

damage to the wires.

NOTE:

The location of clips shown is

an example.
11. Plug the power supply into the main

outlet before pushing the units into the

final position.

12. Units can now be installed.

Fig. 6

Final Checklist

ˆ

Wipe down units

ˆ

Heater 1 on top right side of the freezer

ˆ

Heater 2 on bottom left side of the refrigerator

ˆ

Heater plugged into power supply

ˆ

Power supply adhered to desired position

ˆ

Power cables held away from the floor with the help of clips

ˆ

Power supply plugged into the outlet and green LED on

A

B

C

D

E

Fig. 2

0.5"

0.5"

0.5"

A

B

Also confirm the power supply reaches the

power outlet when placed on top of the

unit (Fig. 4A).
7. Apply the 2 strips of double-sided

tape to the power supply and adhere

the power supply on top of the unit

(Fig. 4B).

8. If the power supply cannot be placed

Fig. 4

A

B

Fig. 3

A

B

C

CAUTION

Use gloves for the next step.