Frigidaire FGMV17WNVFA - Installation Manual
Frigidaire FGMV17WNVFA – Installation Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Before You Use Your Microwave; CONTENTS; General information; Attach Mounting Plate to Wall; Installation Instructions
- Page 4 – If the unit is damaged in shipment,; return the; If the unit is damaged by the customer,; repair or; If the unit is damaged by the installer; Some extra parts are included.; HARDWARE PACKET; PART; PARTS INCLUDED; ADDITIONAL PARTS; Shelf; For some models
- Page 5 – TOOLS YOU WILL NEED; or; MOUNTING SPACE; out from wall using adequate materials supporting
- Page 6 – Draw a line down the center of the studs.; FINDING THE WALL STUDS; Pull the carton up and off the oven.; Screws; Cut the middle of the outer protective plastic bag to; Exhaust Adapter
- Page 7 – DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET; THE MICROWAVE MUST BE LEVEL.
- Page 8 – ALIGNING THE WALL PLATE; Wear gloves; NOTE: DO NOT MOUNT THE PLATE AT THIS; Holes A and B are inside area E. If neither of; at least one wood screw; m ounted; firmly in a stud; to support the weight of the; Set the mounting plate aside
- Page 9 – INSTALLATION TYPES; OUTSIDE TOP EXHAUST; Adaptor in Place for
- Page 10 – Total Ductwork; Maximum duct length:; INSTALLATION INSTRUCTIONS FOR EXTERNAL EXHAUST DUCTING; diameter duct is acceptable to use.
- Page 11 – Roof Cap; Wall Cap; Total Length; EXTERNAL EXHAUST DUCTING
- Page 12 – INSTALLATION OVERVIEW; IMPORTANT :Do not remove the cardboard; spacers b
- Page 13 – EXHAUST; Place the blower unit back into the opening.; with the top of the unit facing up.
- Page 14 – IMPORTANT: If filler blocks are; Exhaust Adaptor; heat shield and door.
- Page 15 – Attach the microwave oven to the top cabinet.; CONNECTING DUCTWORK; furnance; for high temperature applications.
- Page 16 – REMOVE BLOWER PLATE
- Page 17 – USE TOP CABINET TEMPLATE; Roll the blower unit 90°
- Page 18 – Remove the knockout plates in the back of the unit
- Page 19 – IMPORTANT: If filler blocks are not; IMPORTANT: Do not grip or use the handle
- Page 20 – RECIRCULATING
- Page 21 – MOUNT THE MICROWAVE OVEN
- Page 22 – MOUNT THE MICROWAVE; packed with the microwave.; C5. INSTALLING OR CHANGE; Unplug microwave oven or disconnect power.
- Page 23 – lose the microwave door. Plug in microwave
- Page 25 – BEFORE YOU USE YOUR MICROWAVE; INST; ring a nd glas s tray in; DDDDDDD; PRODU; Read the; REGIS; U SE; Replace house fuse or turn breaker back on.; FILL OUT PRODUCT R EGISTRATION CAR D
- Page 26 – Printed in China
READ CAREFULLY.
KEEP THESE INSTRUCTIONS
.
Installation
Over the Range
Instructions
Microwave Oven
Read these instructions completely and carefully.
•
IMPORTANT –
Save these
instructions for local inspector’s use.
•
IMPORTANT –
Observe all
governing codes and ordinances.
•
Note to Installer –
Be sure to leave these
instructions with the Consumer.
BEFORE YOU BEGIN
•
Note to Consumer –
Keep these
instructions for future reference.
•
Skill level
– Installation of this appliance requires
basic mechanical and electrical skills.
•
Proper installation is the responsibility of the installer.
•
Product failure due to improper installation is not
covered under the Warranty.
p/n 316495
or
Questions? Call
1-800-944-9044(US)
1-800-265-8352(Canada)
162
A
201
pril
7
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Other Manuals for Frigidaire FGMV17WNVFA
Summary
Before You Use Your Microwave CONTENTS General information Important Safety Instructions .................................. 3 Electrical Requirements .......................................... 3 Damage – Shipment/Installation.............................. 4 Parts Included...............................
PART QUANTITY Wood Screws 2 ( 1 ⁄ 4 “ x 2“) Toggle Bolts (andwing nuts) ( 3 ⁄ 16 “ x 3“) Self-Aligning Machine 3 Screws ( 1 ⁄ 4 “-28 x 3 1 ⁄ 4 “) Nylon Grommet(for metal cabinets) 1 • If the unit is damaged in shipment, return the unit to the store in which it was bought for repairor replacement. • ...
TOOLS YOU WILL NEED # 1 Phillips screwdriver Pencil Ruler or tape measure andstraight edge Carpenter square(optional) Tin snips (for cuttingdamper, if required) Electric drill with 3 ⁄ 16 “ , 1 ⁄ 2 “ and 5 ⁄ 8 “ drill bits Hammer (optional) Stud finder or Filler blocks or scrapwood pieces, if needed...