Frigidaire FFTA0833S10 - Installation Manual

An Installation Manual for through-the-wall air conditioning units covers essential setup procedures, including safety precautions like proper grounding and compatibility checks with wall sleeves. The guide emphasizes correct dimensions, hardware requirements (such as specified screws), and mounting configurations–including dual-intake grilles, non-directional grills, and unit-mounted setups–to ensure efficient airflow and system performance. It also addresses sealing techniques to prevent air recirculation and highlights critical warnings about product damage from incorrect modifications.

Page 1 – Through-the-Wall AC Installation Hardware and Warnings
Page 2 – Air Conditioner Wall-Sleeve Dimensioning and Mounting Preparation
Page 3 – Replacing Single-Sided Intake Grilles with Dual Intake Grilles
Page 4 – Grille Removal Procedure and Safety Precautions
Page 5 – Alternate Grille Mounting Options
Page 6 – Mounting Dual Intake Grille to Unit Back
Page 7 – Grille Attachment to Sleeve and Ground Wire Installation
Page 8 – Installation of Non-Frigidaire Dual Intake Grille Airflow Control
Page 9 – Grille Substitution and Compatibility in Through-the-Wall Units
Page 10 – Window Air Conditioner Trim Kit Installation

Loading the manual

Hardware

Tapered Spacer (17” Long)

No.

Qty.

Centering/Support Blocks (

”

)

”

x 3

”

x 1

Plastic Divider (

)

1/8

”

x 4

”

x 14

”

Stuffer Seal ( )

”

x 1

”

x 84

”

Seal ( )

”

x 1

”

x 25

”

Seal ( )

”

x 1

”

x 14

”

Seal ( )

”

x 3/8

”

x 25

”

Seal( )

”

x 3/8

”

x 14

”

Seal ( )

”

x 3/4

”

x 14

”

Hardware

Ground Wire (green)

Grounding Screw

No.

Qty.

Trim Frame (top & bottom legs)

Grille (plastic)

Grille Aluminum

Nuts (plastic)

Screw w/washer

Trim Frame (side legs)

Tooth washer for grounding screw

READ BEFORE INSTALLING UNIT

For Through-the-Wall Air Conditioners

Installation Instructions

NOTE:

DO NOT USE ANY SCREWS OTHER THAN THOSE SPECIFIED HERE

Note that the air conditioner dimensions are: 24" wide,14" high, and 19" deep (without front). Install air conditioner
according to these installation instructions to achieve the best performance. Save these installation instructions for
future reference.

Do This First (for existing sleeve)

You may not need all parts in the kit. Discard unused parts.

Items in Kit

16120300A04644

INSTALLATION WARNINGS AND CAUTION

Carefully read the installation manual before beginning. Follow each step as shown.
Observe all local, state, and national electrical codes and by qualified, licensed, authorized personnel only.
Pay attention to danger and safety notices.
To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that
may be exposed.
Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and
install the unit. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp metal fins of front and rear coils.
To prevent injury or strain, use proper lifting and carrying techniques when moving unit.
Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit over an extended
period of time.
Handle air conditioner with care.
Make sure air conditioner does not fall during installation.

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Was this manual helpful?

About this manual

Brand: Frigidaire
Model: FFTA0833S10
Document type: Installation Manual
Language(s): English
Pages: 10
File size: 445.8 KB
Format: PDF

Summary

Page 1 - Through-the-Wall AC Installation Hardware and Warnings

Installation instructions, safety precautions for through-the-wall air conditioners, hardware component lists, and included quantities.

Page 2 - Air Conditioner Wall-Sleeve Dimensioning and Mounting Preparation

Instructions for identifying correct wall-sleeve dimensions by brand, preparation steps for mounting, dimension charts, safety requirements, and grounding procedures illustrated with diagrams.

Page 3 - Replacing Single-Sided Intake Grilles with Dual Intake Grilles

Procedure for replacing single-sided intake grilles with dual intake grilles for air conditioners, including performance compatibility notes and a four-step installation process with images.