Ford 2014 Taurus v.2- User Manual

DATA RECORDING Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, st...

CALIFORNIA PROPOSITION 65 WARNING: Some constituents of engine exhaust, certain vehicle components, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to theState of California to cause cancer and birth defects or otherreproductive harm. PERCH...

Collision Repairs We hope that you never experience a collision, but accidents do happen.Genuine Ford replacement collision parts meet our stringentrequirements for fit, finish, structural integrity, corrosion protection anddent resistance. During vehicle development, we validate that these partsdel...

MOBILE COMMUNICATIONS EQUIPMENT Using mobile communications equipment is becoming increasinglyimportant in the conduct of business and personal affairs. However, youmust not compromise your own or others’ safety when using suchequipment. Mobile communications can enhance personal safety andsecurity ...

GENERAL INFORMATION See the following sections for directions on how to properly use safetyrestraints for children. WARNING: Always make sure your child is secured properly in a device that is appropriate for their height, age and weight. Child safety restraints must be bought separately from your v...

Recommendations for Safety Restraints for Children Child size, height, weight, orage Recommended restrainttype Infants ortoddlers Children weighing 40 lb (18 kg)or less (generally age four oryounger). Use a child safety seat(sometimes called an infantcarrier, convertible seat, ortoddler seat). Small...

CHILD SEAT POSITIONING WARNING: Airbags can kill or injure a child in a child seat. Never place a rear-facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move thevehicle seat upon which the child seat is installed all the way back.When poss...

WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the riskof injury or death in a crash. WARNING: To avoid risk of injury, do not leave children or pets unattende...

BOOSTER SEATS WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the riskof injury or death in a crash. Use a belt-positioning booster seat for children who have o...

Types of Booster Seats • Backless booster seats If your backless booster seat has a removable shield, remove the shield.If a vehicle seating position has a low seat back or no head restraint, abackless booster seat may place your child’s head (as measured at thetops of the ears) above the top of the...

• Place the vehicle seat upon which the child seat will be installed inthe upright position. • Put the safety belt in the automatic locking mode. See Step 5. Thisvehicle does not require the use of a locking clip. Perform the following steps when installing the child seat withcombination lap and sho...

4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear a snap and feel the latchengage. Make sure the tongue islatched securely by pulling on it. 5. To put the retractor in theautomatic locking mode, grasp...

This is necessary to remove the remaining slack that will exist once theextra weight of the child is added to the child restraint. It also helpsto achieve the proper snugness of the child seat to your vehicle.Sometimes, a slight lean toward the buckle will provide extra help toremove remaining slack...

Child seat positioning for LATCH lower anchors All the LATCH lower anchors are equally spaced, 11 inches(28 centimeters) apart, allowing for the following child seat positioning: • If a single child seat is installed using the LATCH lower anchors, it canbe installed at any rear seating position. • I...

4. Clip the tether strap to theanchor as shown. 5. Tighten the child safety seat tether strap according to themanufacturer’s instructions. If your child restraint system is equipped with a tether strap, and thechild restraint manufacturer recommends its use, Ford also recommendsits use. CHILD SAFETY...

PRINCIPLES OF OPERATION WARNING: Never let a passenger hold a child on his or her lap while your vehicle is moving. The passenger cannot protect the child from injury in a crash. WARNING: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a crash, people riding in ...

FASTENING THE SAFETY BELTS The front outboard and rear safety restraints in your vehicle arecombination lap and shoulder belts. 1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until you hear a snap and feelit latch. Make sure the tongue i...

Pregnant women should alwayswear their safety belts. The lap beltportion of a combination lap andshoulder belt should be positionedlow across the hips below the bellyand worn as tight as comfort willallow. The shoulder belt should bepositioned to cross the middle ofthe shoulder and the center of the...

Automatic Locking Mode In this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to remove any slack in the shoulder belt. The automaticlocking mode is not available on the driver safety belt. When to Use the Automatic Locking Mode This mode should be used any time a ch...

SAFETY BELT HEIGHT ADJUSTMENT WARNING: Position the safety belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the safety beltand increase the risk of injury in a crash. Adjust the height of the...

1. Switch the ignition on. Do not start the engine. 2. Wait until the safety belt warning light turns off (about one minute). 3. Wait 10 seconds after the safety belt warning light turns off. • Step 4 must be completed within 20 seconds after the completion ofStep 3. 4. Buckle then unbuckle the safe...

PERSONAL SAFETY SYSTEM™ The Personal Safety System provides an improved overall level of frontalcrash protection to front seat occupants and is designed to help furtherreduce the risk of airbag-related injuries. The system is able to analyzedifferent occupant conditions and crash severity before act...

PRINCIPLES OF OPERATION WARNING: Airbags do not inflate slowly or gently, and the risk of injury from a deploying airbag is the greatest close to the trim covering the airbag module. WARNING: All occupants of your vehicle, including the driver, should always properly wear their safety belts, even wh...

The airbags are a supplemental restraint system and are designed towork with the safety belts to help protect the driver and right frontpassenger from certain upper body injuries. Airbags do not inflate slowly;there is a risk of injury from a deploying airbag. Note: You will hear a loud bang and see...

DRIVER AND PASSENGER AIRBAGS WARNING: Never place your arm or any objects over an airbag module. Placing your arm over a deploying airbag can result in serious arm fractures or other injuries. Objects placed on or over theairbag inflation area may cause those objects to be propelled by theairbag int...

To properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching thepedals comfortably. • Recline the seat slightly (one or two degrees) from the uprightposition. After all occupants have adjusted their seats and put on safety belts,it is very i...

The front passenger sensing system is designed to disable (will notinflate) the front passenger’s frontal airbag when the front passengerseat is unoccupied, or a rear facing infant seat, a forward-facing childrestraint, or a booster seat is detected. Even with this technology,parents are strongly en...

Make sure the front passenger sensing system is operatingproperly. See Crash Sensors and Airbag Indicator later in this chapter. If the airbag readiness light is lit, do the following: The driver and adult passengers should check for objects lodgedunderneath the front passenger seat, or cargo interf...

SAFETY CANOPY® CURTAIN AIRBAGS WARNING: Do not place objects or mount equipment on or near the headliner at the siderail that may come into contact with a deploying curtain airbag. Failure to follow these instructions mayincrease the risk of personal injury in the event of a crash. WARNING: Do not l...

CRASH SENSORS AND AIRBAG INDICATOR WARNING: Modifying or adding equipment to the front end of your vehicle (including frame, bumper, front end body structure and tow hooks) may affect the performance of the airbag system,increasing the risk of injury. Do not modify the front end of yourvehicle. Your...

The fact that the safety belt pretensioners or airbags did not activate forboth front seat occupants in a crash does not mean that something iswrong with the system. Rather, it means the restraints control moduledetermined the accident conditions (such as crash severity, belt usage)were not appropri...

GENERAL INFORMATION ON RADIO FREQUENCIES This device complies with part 15 of the FCC Rules and with IndustryCanada license-exempt RSS standard(s). Operation is subject to thefollowing two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference...

REMOTE CONTROL Integrated Keyhead Transmitters (IKTs) (If Equipped) Use the key blade to start yourvehicle and unlock or lock thedriver door from outside yourvehicle. The transmitter portionfunctions as the remote control. Note: Your vehicle’s keys came with a security label that providesimportant k...

Note: Your vehicle’s back-up keys came with a security tag thatprovides important key cutinformation. Keep the tag in a safeplace for future reference. Replacing the Battery Note: Refer to local regulations when disposing of transmitter batteries. Note: Do not wipe off any grease on the battery term...

Car Finder Press the button twice within three seconds. The horn will soundand the turn signals will flash. We recommend you use thismethod to locate your vehicle, rather than using the panic alarm. Sounding a Panic Alarm Press the button to activate the alarm. Press the button againor switch the ig...

Turning the Vehicle Off After Remote Starting Press the button once. The parking lamps will turn off. You may have to be closer to your vehicle than when starting due toground reflection and the added noise of the running vehicle. You can disable or enable the remote start system through theinformat...

PRINCIPLES OF OPERATION MyKey allows you to program keys with restricted driving modes topromote good driving habits. All but one of the keys programmed to thevehicle can be activated with these restricted modes. Any keys that have not been programmed are referred to asadministrator keys or admin ke...

Configurable Settings With an admin key, you can configure certain MyKey settings when youfirst create a MyKey and before you recycle the key or restart theengine. You can also change the settings afterward with an admin key. • A vehicle speed limit can be set. Warnings will be shown in the displayf...

Programming/Changing Configurable Settings Use the information display to access your configurable MyKey settings: 1. Switch the ignition on using an admin key. If your vehicle haspush-button start, place the intelligent access key fob into the backupslot. The location of your backup slot is in anot...

NUMBER OF MYKEY(S) Indicates the number of MyKeys programmed to your vehicle. Use thisfeature to detect how many MyKeys you have for your vehicle anddetermine when a MyKey has been deleted. NUMBER OF ADMIN KEY(S) Indicates how many admin keys are programmed to your vehicle. Usethis feature to determ...

Condition Potential causes I cannot clear theMyKeys. • The key or fob used to start the vehicle does not have admin privileges. • No MyKeys are created. Refer to Creating a MyKey. I lost the only adminkey. • Purchase a new key from your authorized dealer. I lost a key. • Program a spare key. See Sec...

LOCKING AND UNLOCKING You can use the power door lock control or the remote control to lockand unlock your vehicle. Power Door Locks The power door lock control is located on the driver and front passengerdoor panels. A. Unlock B. Lock Remote Control You can use the remote control anytime your vehic...

Note: If any door or the luggage compartment is open, or if the hood is open on vehicles with an anti-theft alarm or remote start, the hornsounds twice and the lamps will not flash. Opening the Trunk Press the button twice within three seconds to open the trunk. Make sure to close and latch the trun...

You can still lock your vehicle with the key in the ignition. To do this,use the keyless entry keypad with the driver door closed, or press thelock button on the transmitter even if the doors are not closed. If both front doors are closed, you can lock your vehicle by any method,regardless of whethe...

Autounlock Feature (If Enabled) The autounlock feature will unlock all the doors when: • the ignition is on, all the doors are closed, and your vehicle has beenin motion at a speed greater than 12 mph (20 km/h); • your vehicle has then come to a stop and the ignition is switched offor to accessory; ...

You can operate the keypad with the factory-set 5-digit entry code.The code is located on the owner’s wallet card in the glove box and isavailable from an authorized dealer. You can also create up to three ofyour own 5-digit personal entry codes. Programming a Personal Entry Code To create your own ...

Anti-Scan Feature The keypad will go into an anti-scan mode if you enter the wrong codeseven times (35 consecutive button presses). This mode disables thekeypad for one minute and the keypad lamp will flash. The anti-scan feature will turn off after: • one minute of keypad inactivity • pressing the ...

You will see the factory-set code in the message center. The codeappears for a few seconds. Note: The code may not display until after any other warning messages first display. TRUNK RELEASE From Inside Your Vehicle Press the button located on the instrument panel. Vehicles with Intelligent Access 1...

INTERIOR LUGGAGE COMPARTMENT RELEASE WARNING: Keep vehicle doors and luggage compartment locked and keep keys and remote transmitters out of a child’s reach. Unsupervised children could lock themselves in the trunk and riskinjury. Children should be taught not to play in vehicles. WARNING: Do not le...

ADJUSTING THE STEERING WHEEL WARNING: Do not adjust the steering wheel when your vehicle is moving. Note: Make sure that you are sitting in the correct position. See Sitting in the Correct Position in the Seats chapter. 1. Unlock the steering column. 2. Adjust the steering wheel to thedesired positi...

Power Tilt and Telescope Steering Column (If Equipped) WARNING: Do not adjust the steering wheel when your vehicle is moving. Note: Make sure that you are sitting in the correct position. Refer to Sitting in the Correct Position in the Seats chapter. Use the control on the side of thesteering column...

To reset the steering column to its normal stopping position: 1. Press the steering column control again after encountering the newstopping position. 2. Continue pressing the control until it reaches the end of the columnposition. A new stopping position is set. The next time you tilt or telescope t...

CRUISE CONTROL Type 1 Type 2 See the Cruise Control chapter for information on this feature. SET RES CNCL ON OFF GAP 84 Steering Wheel 2014 TaurusOwners Guide gf, 2nd Printing, September 2013USA (fus)

ADJUSTABLE PEDALS (IF EQUIPPED) WARNING: Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving. The control is located on the left side of the steering column. Press andhold the appropriate control to move the pedals. A. Farther B. Closer The pedal position...

WINDSHIELD WIPERS Note: Fully defrost the windshield before switching on the windshield wipers. Note: Make sure you switch off the windshield wipers before entering a car wash. Note: Clean the windshield and wiper blades if they begin to leave streaks or smears. If that does not resolve the issue, i...

WINDSHIELD WASHERS Note: Do not operate the wipers on a dry windshield. This may scratch the glass, damage the wiper blades or cause the wiper motor to burn out.Always use the windshield washer before wiping a dry windshield. Note: Do not operate the washer when the washer reservoir is empty. This m...

LIGHTING CONTROL A. Off B. Parking lamps, instrument panellamps, license plate lamps and taillamps C. Headlamps High Beams • Push the lever toward theinstrument panel to activate. • Push the lever toward theinstrument panel again or pullthe lever towards you todeactivate. Headlamp Flasher • Pull tow...

AUTOLAMPS WARNING: In severe weather conditions, it may be necessary to switch your headlamps on manually. Note: If the vehicle is equipped with autolamps, it will have the windshield wiper rainlamp feature. When the windshield wipers are turned to low- or high-speed wiping during daylight, and the ...

HEADLAMP EXIT DELAY You can set the delay time to keep the headlamps on for up to threeminutes after the ignition is turned off. Follow the steps below to change the delay time (Steps 1 through 6must be done within 10 seconds): 1. Turn the ignition off. 2. Turn the lighting control to the autolamp p...

AUTOMATIC HIGH BEAM CONTROL (IF EQUIPPED) The system will automatically turn on your high beams if it is darkenough and no other traffic is present. When it detects an approachingvehicle’s headlights, a preceding vehicle’s tail lamps or street lighting, thesystem will turn off the high beams (low be...

• The ambient light level is high enough that high beams are notneeded. • Severe rain, snow or fog is detected. • The camera is blocked. Activating the system Switch the system on within the information display. See Information displays . Turn the lighting control to theautolamps position. Manually ...

DIRECTION INDICATORS • Push down to activate the leftturn signal. • Push up to activate the right turnsignal. Note: Tap the lever up or down to make the direction indicators flash only three times to indicate a lane change. INTERIOR LAMPS Front row map lamps The map lamps are located on theoverhead ...

Rear dome/reading lamps Your vehicle may have readinglamps within the rear domelamp(s). Press the switches on either sideof the dome lamp to turn on thereading lamps. The direction of thereading lamps can be adjusted bypressing on the sides of the readinglamps. The dome/reading lamps will light when...

POWER WINDOWS WARNING: Do not leave children unattended in your vehicle and do not let children play with the power windows. They may seriously injure themselves. WARNING: When closing the power windows, you should verify they are free of obstructions and make sure that children and pets are not in ...

Bounce-Back (One-Touch Up or Down Windows Only) The window stops automatically while closing and reverse some distanceif there is an obstacle in the way. Overriding the Bounce-Back Feature WARNING: When you override the bounce-back feature the window will not reverse if it detects an obstacle. Take ...

EXTERIOR MIRRORS Power Exterior Mirrors WARNING: Do not adjust the mirror while your vehicle is in motion. A. Left mirror B. Adjustment control C. Right mirror To adjust your mirrors: 1. Press the button to select the mirror you want to adjust. An indicatorlight on the button will illuminate. 2. Use...

Integrated Blind Spot Mirrors (If Equipped) WARNING: Objects in the blind spot mirror are closer than they appear. Blind spot mirrors have an integrated convex mirror built into the upperoutboard corner of the exterior mirrors. They are designed to assist youby increasing visibility along the side o...

INTERIOR MIRROR WARNING: Do not adjust the mirror when your vehicle is moving. Note: Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum or ammonia based cleaning products. You can adjust the interior mirror to your preference. Some mirrors alsohave a second...

Illuminated Visor Vanity Mirror Lift the cover to switch on thelamp. SUNSHADE (IF EQUIPPED) The power rear sunshade covers the rear window of the vehicle. The control is located in the centerconsole access bin. Press the control to move the sunshade up or down. Note: Do not try to manually move the ...

GAUGES Type 1 Cluster shown in standard measure – metric clusters similar. A. Tachometer B. Information display. See Information displays for more information. C. Speedometer D. Fuel gauge Fuel gauge Indicates approximately how much fuel is left in the fuel tank (when theignition is on). The fuel ga...

Type 2 Cluster shown in standard measure – metric clusters similar. A. Left information display. See Information displays for more information. B. Speedometer C. Right information display. See MyFord Touch™ for more information. WARNING LAMPS AND INDICATORS These indicators can alert you to a vehicl...

Adaptive cruise control (if equipped) (RTT) The speed control system indicator light changes color to indicate whatmode the system is in: • On (white light): Illuminates when the adaptive cruise control systemis turned on. Turns off when the speed control system is turned off. • Engaged (green light...

High beams Illuminates when the high-beam headlamps are on. Low fuel (RTT) Illuminates when the fuel level in the fuel tank is at or nearempty. Low tire pressure warning Illuminates when your tire pressure is low. If the light remainson at start up or while driving, the tire pressure should bechecke...

Service engine soon The service engine soon indicator light illuminates when the ignition is first turned to the on position to check the bulb andto indicate whether the vehicle is ready for Inspection/Maintenance (I/M) testing. Normally, the “service engine soon”light will stay on until the engine ...

GENERAL INFORMATION WARNING: Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus offthe road. Your primary responsibility is the safe operation of yourvehicle. We recommend...

†Trip 1 & 2 Trip Odometer Hold OK to Reset Trip Timer Average Fuel Compass (located in lower line of display). Note: this will also display in other menus. Total Odometer (located in lower line of display). Note: this will also display in other menus. †See Trip and fuel economy computer later in...

Settings Driver Assist Traction Control — check enabled (default) / uncheckdisabled Blind Spot — check enabled (default) / uncheckdisabled Collision Warning Sensitivity High, Normal orLow Chimes (not selectable if using aMyKey) Warning (not selectable if using aMyKey) Cross Traffic — check enabled (...

Information Messages See Information Messages later in this chapter for more information. Information Display Controls (Type 2) • Press the up and down arrowbuttons to scroll through andhighlight the options within amenu. • Press the right arrow button toenter a sub-menu. • Press the left arrow butt...

Driver Assist In this mode, you can configure different driver setting choices. Note: Some items are optional and may not appear. Driver Assist Traction Ctrl — check enabled (default) / uncheck disabled Blindspot — check enabled (default) / uncheck disabled Collision Warn Sensitivity High / Normal /...

INFORMATION MESSAGES Note: Depending on the vehicle options equipped with your vehicle, not all of the messages will display or be available. Certain messages may beabbreviated or shortened depending upon which cluster type you have. Press the OK button toacknowledge and remove somemessages from the...

Alarm/Security Messages Action / Description Vehicle Alarm To StopAlarm, Start Vehicle. Displayed when the perimeter alarm system isarmed and the vehicle is entered using the keyon the driver’s side door. In order to preventthe perimeter alarm system from triggering,the ignition must be turned to st...

AWD Messages Action / Description Change AWD PowerTransfer Unit Lube Displayed when the AWD system needs itspower transfer unit lubrication changed. Thismessage may be set if a vehicle hasexperienced extended periods ofextreme/severe duty cycle driving. See yourauthorized dealer for service. (Taurus...

BLIS® Messages Action / Description Blindspot NotAvailable SensorBlocked See Manual Displayed when the blind spot informationsystem/cross traffic alert system sensors areblocked. Driver can typically clean the sensorto resolve. Blindspot System Fault Displayed when a fault with the blind spot inform...

Collision Warning System Messages Action / Description Collision Warning NotAvailable Displayed when there is a system malfunctionwith the collision warning system. The systemwill be disabled. Contact your authorizeddealer as soon as possible. Collision Warning NotAvailable SensorBlocked See Manual ...

Lane Keeping System Messages Action / Description Lane keeping Sys.Malfunction Servicerequired The system has malfunctioned. Contact yourauthorized dealer as soon as possible. Front CameraTemporarily NotAvailable The system has detected a condition that hascaused the system to be temporarilyunavaila...

Passenger Sensing System Message Action / Description Occupant SensorBLOCKED RemoveObjects NearPassenger Seat Displayed when objects are by the passengerseat. After the objects are moved away fromthe seat, if the warning stays on or continuesto come on contact your authorized dealer assoon as possib...

MANUAL HEATING AND AIR CONDITIONING SYSTEM A. Fan speed control: Controls the volume of air circulated in your vehicle. Turn to select the desired fan speed or switch off. If you switchthe fan off, the windshield may fog up. B. Defrost: Distributes air through the windshield defroster vents and demi...

F. Temperature control: Controls the temperature of the air circulated in your vehicle. Turn to select the desired temperature. G. MAX A/C: Distributes recirculated air through the instrument panel vents to cool the vehicle. This position is more economical and efficientthan normal air conditioning....

DUAL AUTOMATIC TEMPERATURE CONTROL SYSTEM Note: You can switch temperature units between Fahrenheit and Celsius. See Menu features in the MyFord Touch or MyLincoln Touch chapter. A. Power/Driver temperature control: Press to turn the climate control system off and on. When the system is off, outside...

E. A/C: Press to turn air conditioning off and on. Air conditioning cools the vehicle using outside air. To improve air conditioning when startingyour vehicle, drive with the windows slightly open for two to threeminutes.Use air conditioning with recirculated air to improve cooling performanceand ef...

F. A/C: Press to turn air conditioning off and on. Air conditioning cools the vehicle using outside air. To improve air conditioning when startingyour vehicle, drive with the windows slightly open for two to threeminutes.Use air conditioning with recirculated air to improve cooling performanceand ef...

During extreme high ambient temperatures when idling stationary forextended periods in gear, run the air conditioning in the MAX A/C mode,adjust the blower fan speed to the lowest setting and put the vehicle’stransmission into position P (automatic transmission) to continue to receive cool air from ...

transmission into position P (automatic transmission) to continue to receive cool air from your air conditioning system. For maximum cooling performance in AUTO mode, press MAX A/C. For maximum cooling performance in manual override control:1. Choose the Panel, A/C, and recirculated air controls.2. ...

CABIN AIR FILTER Note: Make sure you have a cabin air filter installed at all times. This prevents foreign objects from entering the system. Running the systemwithout a filter in place could result in degradation or damage to thesystem. Your vehicle is equipped with a cabin air filter, which is loca...

Manual Climate Systems In hot weather, the climate control system is set to MAX A/C. In moderate weather, the system either heats or cools (based onprevious settings). The rear defroster and heated mirrors are notautomatically turned on. In cold weather, maximum heat is provided in floor/defrost mod...

SITTING IN THE CORRECT POSITION WARNING: Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the passenger sensing system, resulting inserious injury or death in a crash. Always sit upright against your seatba...

Rear seat center head restraint The head restraints consist of: A. An energy absorbing head restraint B. Two steel stems C. Guide sleeve adjust and release button D. Guide sleeve unlock and remove button • Raise: Pull up on the head restraint (A). • Lower: Press and hold the guide sleeve adjust and ...

MANUAL SEATS WARNING: Do not adjust the driver’s seat or seatback while the vehicle is moving. WARNING: Rock the seat backward and forward after releasing the lever to make sure that it is fully engaged. Moving the seats backward andforward WARNING: Before returning the seatback to its original posi...

move to the easy entry position. The seat will move to the final positionwhen the key is in the ignition or when the push button start system isput in accessory mode or started. To program the memory feature to a remote control, see the Keys and remote control chapter. Easy Entry and Exit Feature (I...

Ventilated Seats The ventilated seats will only function when the engine is running. To operate the ventilated seats: Press the ventilated seat symbol to cycle through thevarious cooling settings and off. Cooler settings areindicated by more indicator lights. If the engine falls below 350 RPM while ...

To install a filter: 1. First, position the filter in itshousing making sure that the farforward end is all the way up in thehousing. 2. Push in on the center of theoutside edge of the filter and rotateup into the housing until it clipsinto position. REAR SEATS Split-folding Rear Seat WARNING: Befor...

HOMELINK® WIRELESS CONTROL SYSTEM (IF EQUIPPED) WARNING: Make sure that the garage door and security device are free from obstruction when you are programming. Do not program the system with the vehicle in the garage. WARNING: Do not use the system with any garage door opener that does not have the ...

Programming Note: Put a new battery in the hand-held transmitter. This will ensure quicker training and accurate transmission of the radio-frequency signal. 1. With your vehicle parked outside of the garage and your key in theignition, turn the key so that the ignition is in the on position. 2. Hold...

Note: You may need a ladder to reach the unit and you may need to remove the cover orlamp lens on your garage door opener. 5. Press the learn button on the garage dooropener motor, and then you have 30 secondsto complete the next step. 6. Return to your car. 7. Press and hold the function button you...

Programming HomeLink to the Genie Intellicode garage dooropener motor Note: You may need a ladder to access the garage door opener motor. To program HomeLink to the garagedoor opener motor: 1. Press and hold the PROGRAMbutton on the garage door openermotor until both blue LED’s turn on. 2. Release t...

AUXILIARY POWER POINTS WARNING: Do not plug optional electrical accessories into the cigarette lighter socket (if equipped). Improper use of the lighter can cause damage not covered by your warranty, and can result in fireor serious injury. Note: If used when the engine is not running, the battery w...

CENTER CONSOLE Stow items in the cupholder carefully as items may become loose duringhard braking, acceleration or collisions, including hot drinks which mayspill. Note: The appearance and features of the center console may be different than shown based on your vehicle’s option level. Available cons...

OVERHEAD CONSOLE The appearance of the overhead console will vary according to youroption package. Press near the rear edge of the doorto open it. Storage Compartments 163 2014 TaurusOwners Guide gf, 2nd Printing, September 2013USA (fus)

GENERAL INFORMATION WARNING: Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system, creating the risk of fire or other damage. WARNING: Do not park, idle, or drive your vehicle on dry grass or other dry ground cover. The emission system heats up th...

Ignition Modes Off: Turns the ignition off. • Without applying the brake pedal, press and release the button oncewhen the ignition is in the on mode, or when the engine is runningbut the vehicle is not in motion. Accessory: Allows some electrical accessories to operate while the engine is not runnin...

Fast Restart (Vehicles with Keyless Start) The fast restart feature allows you to restart the engine within20 seconds of switching it off, even if a valid key is not present. Within 20 seconds of switching the engine off, press the brake pedal andpress the button. After 20 seconds have expired, you ...

• During the countdown before engine shutdown, you are prompted topress OK or RESET (depending on your type of information display) to temporarily switch the feature off (for the current ignition cycleonly). Stopping the Engine When Your Vehicle is Stationary 1. Move the transmission selector lever ...

Guarding Against Exhaust Fumes WARNING: If you smell exhaust fumes inside your vehicle, have this checked immediately. Do not drive your vehicle if you smell exhaust fumes. Carbon monoxide is present in exhaust fumes.Take precautions to avoid its dangerous effects. Important Ventilating Information ...

• Do not use multiple extension cords. • Make sure that when in operation, the extension cord plug and theheater cord plug connections are free and clear of water. This couldcause an electric shock or fire. • Make sure your vehicle is parked in a clean area, clear ofcombustibles. • Make sure the hea...

SAFETY PRECAUTIONS WARNING: Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. WARNING: The fuel system may be under pressure. If you hear a hissing sound near the fuel filler inlet, do not refuel until the sound stops. Otherwise, fue...

• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes,remove contact lenses (if worn), flush with water for 15 minutes andseek medical attention. Failure to seek proper medical attention couldlead to permanent injury. • Fuels can also be harmful if absorbed through the skin. If f...

Choosing the Right Fuel With a Flex Fuel Vehicle (If Equipped) Use only UNLEADED gasoline or UNLEADED gasoline blended witha maximum of 85% ethanol (E-85) in your Flex Fuel Vehicle (FFV).If your vehicle is flex fuel capable, it will have a yellow bezel placedover the fuel fill inlet. Do not use: • F...

RUNNING OUT OF FUEL Avoid running out of fuel because this situation may have an adverseeffect on powertrain components. If you have run out of fuel: • You may need to cycle the ignition from off to on several times afterrefueling to allow the fuel system to pump the fuel from the tank tothe engine....

1. Locate the white plastic funnel in the spare tire compartment. 2. To open the fuel filler door, pressthe center of the rear edge and thenrelease. 3. Slowly insert the funnel into the capless fuelsystem. 4. Fill the vehicle with fuel from the portable fuel container. 5. When done, clean the funnel...

Use the following guidelines to avoid electrostatic charge build-up whenfilling an ungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle (including thecargo area). • Keep the fuel pump nozzle in contact with the fuel conta...

Keep a record for at least one month and record the type of driving(city or highway). This provides an accurate estimate of the vehicle’s fueleconomy under current driving conditions. Additionally, keeping recordsduring summer and winter show how temperature impacts fuel economy.In general, lower te...

AUTOMATIC TRANSMISSION WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the off position and remove the key whenever you leave your vehicle. Your vehicle has been designed to improve fuel economy by reducingfuel usage while coasting...

S (Sport) Moving the gearshift lever to S (Sport): • Provides additional grade (engine) braking and extends lower gearoperation to enhance performance for uphill climbs, hilly terrain ormountainous areas. This will increase engine RPM during enginebraking. • Provides additional lower gear operation ...

The system will determine when temporary manual control is no longerdesired and reverts back to automatic control. Extensive manual controlcan be achieved by moving the shifter to the S (Sport) position. Thesystem will stay in manual control until the shifter is moved out of themanual position. If y...

Brake-Shift Interlock WARNING: Do not drive your vehicle until you verify that the brake lamps are working. WARNING: When doing this procedure, you will be taking the vehicle out of park which means the vehicle can roll freely. To avoid unwanted vehicle movement, always fully set the parking brakepr...

2. Insert the screwdriver (or similartool) into the hole and press the leverforward while pulling the gearshiftlever out of position P and into theposition N. 3. Remove the tool and reinstall theinsert. 4. Start the vehicle and release theparking brake. Automatic Transmission Adaptive Learning This ...

GENERAL INFORMATION Note: Occasional brake noise is normal. If a metal-to-metal, continuous grinding or continuous squeal sound is present, the brake linings may beworn out. Have them inspected by an authorized dealer. If your vehiclehas continuous vibration or shudder in the steering wheel while br...

PRINCIPLES OF OPERATION The traction control system helps avoid drive wheel spin and loss oftraction. If your vehicle begins to slide, the system applies the brakes to individualwheels and, when needed, reduces engine power at the same time. If thewheels spin when accelerating on slippery or loose s...

PRINCIPLES OF OPERATION WARNING: Vehicle modifications involving braking system, aftermarket roof racks, suspension, steering system, tire construction and wheel or tire size may change the handlingcharacteristics of your vehicle and may adversely affect theperformance of the AdvanceTrac® system. In...

USING ADVANCETRAC® The system automatically activates when you start your engine. Theelectronic stability control portion of the system is disabled when thetransmission is in reverse (R) or, on SHO models, if you press the ESCOFF switch and hold it for more than five seconds when the brakes areappli...

SENSING SYSTEM (IF EQUIPPED) WARNING: To help avoid personal injury, please read and understand the limitations of the system as contained in this section. Sensing is only an aid for some (generally large and fixed)objects when moving in reverse on a flat surface at parking speeds.Traffic control sy...

When receiving a detection warning, the radio volume is reduced to apredetermined level. After the warning goes away, the radio volumereturns to the previous level. The system can be turned off using the information display control.Refer to the Information Display chapter. If a fault is present in t...

Using Active Park Assist Press the button; the touch screendisplays a message and acorresponding graphic to indicateit’s searching for a parking space.Use the turn signal to indicatewhich side of the vehicle you wantthe system to search on. Note: If the turn signal is not on, the system automaticall...

Automatic Steering into Parking Space Note: If vehicle speed exceeds 6 mph (10 km/h), the system turns off and you need to take full control of the vehicle. Note: If a maneuver is interrupted before completion, the system turns off and you need to full take control of the vehicle. In some instancesa...

The system does not offer a particular space The vehicle is farther than 5 ft (1.5 m) from the parking space The vehicle is closer than 16 in. (40 cm) from neighboring parkedvehicles The transmission is in R (Reverse); the vehicle must be movingforward to detect a parking space The system does not p...

Using the Rear View Camera System The rear view camera system displays what is behind your vehicle whenyou place the transmission in R . The system uses fixed guidelines which show the actual path the vehicle is moving in while reversing in astraight line. This can be helpful when backing into a par...

Guidelines and the Centerline Note: Fixed guidelines and active guidelines (if equipped) are only available when the transmission is in R (Reverse). Note: The centerline is only available if Fixed or Active (if equipped) guidelines are on. A. Active guidelines (if equipped) B. Centerline C. Fixed gu...

PRINCIPLES OF OPERATION Cruise control lets you maintain a set speed without keeping your footon the accelerator pedal. USING CRUISE CONTROL WARNING: Do not use cruise control in heavy traffic, on winding roads or when the road surface is slippery. This could result in loss of vehicle control, serio...

WARNING: Do not use the adaptive cruise control when entering or leaving a highway, in heavy traffic or on roads that are winding, slippery or unpaved. WARNING: Do not use in poor visibility, specifically fog, rain, spray or snow. Note: It is your responsibility to stay alert, drive safely and be in...

• the vehicle speed falls below 16 mph (26 km/h) • a new gap distance is set. The vehicle brakes will be automatically applied to slow your vehicle tomaintain a safe distance from the vehicle in front. The maximum brakingwhich is applied by the system is limited and can be overridden by thedriver ap...

Detection issues can occur: A. When driving on a different linethan the vehicle in front. B. With vehicles that edge into yourlane. The system can only detectthese vehicles once they move fullyinto your lane. C. There may be issues with thedetection of vehicles in front whendriving into and coming o...

Blocked Sensor WARNING: Do not use ACC when towing a trailer with brake controls. Aftermarket trailer brakes will not function properly when ACC is activated because the brakes are electronically controlled.Failing to do so may result in loss of vehicle control, which could resultin serious injury. ...

Cause Action Swirling water, or snow or ice onthe surface of the road mayinterfere with the radar signals. Do not use system in theseconditions because it may notdetect any vehicle ahead. You are in a desert or remote areawith no other vehicles and noroadside objects. Wait a short time or switch ton...

DRIVER ALERT (IF EQUIPPED) WARNING: The driver alert system is designed to aid you. It is not intended to replace your attention and judgment. You are still responsible to drive with due care and attention. Note: The system will store the on/off setting in the information display menu through igniti...

System Display When active the system will run automatically in the background andonly issue warning if required. You can view the status at any time usingthe information display. Refer to the Information Displays chapter. The alertness level is shown by six steps in a colored bar. The current asses...

System Display When you switch the system on, an overhead graphic of avehicle with lane markings will be displayed in the leftinstrument cluster display. If the aid mode is selected after you switch the system on,arrows will be displayed with the lane markings. When you switch the system off, the la...

Using the Systems BLIS® turns on when the engine is started and the vehicle is drivenforward above 3 mph (5 km/h); it remains on while the transmission isin D (Drive) and N (Neutral). If shifted out of D (Drive) or N (Neutral),the system enters CTA mode. Once shifted back into D (Drive), BLIS®turns ...

Zone coverage also decreases when parking at shallow angles. Here, theleft sensor is mostly obstructed; zone coverage on that side is severelylimited. System Lights and Messages The BLIS® and CTA systemsilluminate a yellow alert indicator inthe outside mirror on the side ofthe vehicle the approachin...

System Sensors WARNING: Just prior to the system recognizing a blocked condition and alerting the driver, the number of missed objects will increase. To help avoid injuries, NEVER use the BLIS® as areplacement for using the side and rear view mirrors and looking overyour shoulder before changing lan...

Switching the Systems Off and On One or both systems can be switched off temporarily by using theinformation display control; refer to the Information Display chapter. When the BLIS® is switched off, the driver does not receive alerts andthe information display shows BLIND SPOT SYS OFF and/or CTASYS...

If it is, a red warning lightilluminates and an audible warningchime sounds. The brake support system assists the driver in reducing the collisionspeed by charging the brakes. If the risk of collision further increasesafter the warning light illuminates, the brake support prepares the brakesystem fo...

WARNING: The electric power steering system has diagnostic checks that continuously monitor the system to ensure proper operation of the electronic system. When an electronic error isdetected, a message will be displayed in the information display.If this happens, stop the vehicle in a safe place, a...

CARGO NET (IF EQUIPPED) WARNING: The cargo net is not designed to restrain objects during a collision or heavy braking. The cargo net secures lightweightobjects in the cargo area. Attachthe net to the anchors provided.Do not put more than 50 pounds(22 kilograms) in the net. LOAD LIMIT Vehicle Loadin...

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-Pillar or the edge of the driver’s door(vehicles exported outside the US and Canada may not have a TireLabel). Look for “THE COMBINED WEI...

Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loadweight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all pa...

GVWR (Gross Vehicle Weight Rating) – is the maximum allowable weight of the fully loaded vehicle (including all options, equipment,passengers and cargo). The GVWR is shown on the Safety Compliance Certification Label. The label shall be affixed toeither the door hinge pillar, door-latch post, or the...

WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structural damage,serious damage to the vehicle, loss of control and personal injury. GCW (Gross Combined Weight) – is th...

WARNING: Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury. Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.” on your vehicle’s pla...

TOWING A TRAILER WARNING: Do not exceed the GVWR or the GAWR specified on the certification label. WARNING: Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of your vehicle and could result in engine damage, transmission damage, structural damage, lossof vehicle ...

Hitches Do not use a hitch that either clamps onto the bumper or attaches to theaxle.Distribute the trailer load so 10-15% of the total trailer weight is on thetongue. Safety Chains Note: Never attach safety chains to the bumper. Always connect the safety chains to the hook retainers of your vehicle...

Exceeding these limits may allow water to enter vehicle components: • Causing internal damage to the components. • Affecting driveability, emissions, and reliability. Replace the rear axle lubricant anytime the rear axle submerges inwater. Water may have contaminated the rear axle lubricant, which d...

It is acceptable to have your front-wheel drive vehicle towed from thefront if using proper wheel lift equipment to raise the front wheels offthe ground. When towing in this manner, the rear wheels can remain onthe ground. Front-wheel drive vehicles must have the front wheels placed on a towdolly wh...

BREAKING-IN You need to break in new tires for approximately 300 miles(480 kilometers). During this time, your vehicle may exhibit some uniquedriving characteristics. Avoid driving too fast during the first 1000 miles(1600 kilometers). Vary your speed frequently and change up throughthe gears early....

• Carry unnecessary weight (approximately 1 mpg [0.4 km/L] is lost forevery 400 pounds [180 kilograms] of weight carried). • Add particular accessories to your vehicle (e.g.; bug deflectors,rollbars or light bars, running boards, ski racks). • Drive with the wheels out of alignment. DRIVING THROUGH ...

FLOOR MATS WARNING: Always use floor mats that are designed to fit the foot well of your vehicle, leaving the pedal area unobstructed, and which can be firmly secured to retention posts so that they cannotslip out of position and interfere with the pedals or impair safeoperation of your vehicle in o...

ROADSIDE ASSISTANCE Vehicles Sold in the United States: Getting Roadside Assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary Roadside Assistance program.This program is separate from the New Vehicle Limited Warranty. • 24 hours a day, seven days...

If you need to arrange roadside assistance for yourself, Ford MotorCompany will reimburse a reasonable amount for towing to the nearestdealership within 35 miles (56.3 kilometers). To obtain reimbursementinformation, U.S. Ford vehicle customers call 1-800-241-3673. Customerswill be asked to submit t...

2. Check all battery terminals. Remove the positive terminal cover(if equipped) and any excessive corrosion before you attach the batterycables. Ensure that vent caps are tight and level. 3. Turn the heater fan on in both vehicles to protect from any electricalsurges. Turn all other accessories off....

Jump Starting 1. Start the engine of the booster vehicle and run the engine at amoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizeddealer. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfaction. Plea...

• Ford Genuine Accessories • Service specials and promotions. In Canada: Mailing address Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6K 1C8 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Additional Assistance If you have questions or concerns,...

UTILIZING THE MEDIATION or ARBITRATION PROGRAM(CANADA ONLY) This pertains to vehicles delivered to authorized Canadian dealers.In those cases, where you continue to feel that the efforts by Ford ofCanada and the authorized dealer to resolve a factory-related vehicleservice concern have been unsatisf...

CHANGING A FUSE Fuses WARNING: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. If electrical components in yourvehicle are not working, a fuse mayhave blown. Blown fuses areidentifi...

FUSE SPECIFICATION CHART Power Distribution Box WARNING: Always disconnect the battery before servicing high current fuses. WARNING: To reduce risk of electrical shock, always replace the cover to the power distribution box before reconnecting the battery or refilling fluid reservoirs. The power dis...

Passenger Compartment Fuse Panel The fuse panel is located under the instrument panel to the left of thesteering wheel. You may need to remove a trim panel to access it. The fuses are coded as follows. Fuse or relay number Fuse amp rating Protected components 1 30A Left front and right rear smartwin...

GENERAL INFORMATION Have your vehicle serviced regularly to help maintain its roadworthinessand resale value. There is a large network of Ford authorized dealers whoare there to help you with their professional servicing expertise. We believethat their specially trained technicians are best qualifie...

OPENING AND CLOSING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column. 2. Go to the front of the vehicle andrelease the auxiliary latch that islocated under the front center ofthe hood. 3. Lift the hood. Maintenance 27...

UNDER HOOD OVERVIEW 3.5L V6 engine A. Engine coolant reservoir B. Windshield washer fluid reservoir C. Brake fluid reservoir D. Battery E. Power distribution box F. Air filter assembly G. Automatic transmission fluid dipstick H. Engine oil dipstick I. Engine oil filler cap A I H G F B C D E 280 Main...

Engine shield Some vehicles may be equipped with an aero-shield under the engine.This shield needs to be removed for service, including oil and filterchanges. It is secured with four quick release fasteners. 282 Maintenance 2014 TaurusOwners Guide gf, 2nd Printing, September 2013USA (fus)

2.0L EcoBoost® Engine A. Engine coolant reservoir B. Brake fluid reservoir C. Battery D. Power distribution box E. Air filter assembly F. Engine oil filler cap G. Engine oil dipstick H. Windshield washer fluid reservoir A H G F E B C D Maintenance 283 2014 TaurusOwners Guide gf, 2nd Printing, Septem...

Only use oils certified for gasoline engines by theAmerican Petroleum Institute (API). An oil with thistrademark symbol conforms to the current engineand emission system protection standards and fueleconomy requirements of the International LubricantsSpecification Advisory Council (ILSAC), comprised...

Adding Engine Coolant WARNING: Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hotengine parts. WARNING: Do not put engine coolant in the windshield washer fluid contai...

• Do not add extra inhibitors or additives to the coolant. These can beharmful and compromise the corrosion protection of the enginecoolant. Unscrew the cap slowly. Any pressure will escape as you unscrew the cap. Add prediluted engine coolant meeting the Ford specification. See Capacities and Speci...

Engine fluid temperature management (EcoBoost engine only) WARNING: To reduce the risk of collision and injury, be prepared that the vehicle speed may reduce and the vehicle may not be able to accelerate with full power until the fluid temperatures reduce. Your vehicle has been designed to pull a tr...

WARNING: Never remove the coolant reservoir cap while the engine is running or hot. 4. If the coolant level is normal, you may restart your engine andcontinue on. 5. If the coolant is low, add coolant, restart the engine and take yourvehicle to an authorized dealer. See Adding engine coolant in this...

When Fail-Safe Mode is Activated You have limited engine power when in the fail-safe mode, so drive thevehicle with caution. The vehicle will not be able to maintain high-speedoperation and the engine will run rough. Remember that the engine iscapable of completely shutting down automatically to pre...

7. Without disconnecting the sensor (4), pull the air filter assembly up todisconnect the air filter assembly from the seated grommets locatedunderneath the air filter assembly. 8. Rotate the air filter assembly90 degrees counterclockwise andreinstall into the rubber hose. 9. Tighten the clamp (1). ...

4. Seat the air filter assembly back into the grommets by pushing downon the air filter assembly. 5. Tighten the clamp. 6. Install and tighten two bolts that attach air filter assembly to the frontof the vehicle. 7. Install the bolt cover (if equipped). 8. Reinstall the harness retaining clip into t...

CHANGING THE VEHICLE BATTERY WARNING: Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near thebattery, always shield your face and protect your eyes. Always provideproper v...

Battery relearn Because your vehicle’s engine is electronically controlled by a computer,some control conditions are maintained by power from the battery. Whenthe battery is disconnected or a new battery is installed, the engine mustrelearn its idle and fuel trim strategy for optimum driveability an...

CHECKING THE WIPER BLADES Run the tip of your fingers over the edge of the bladeto check for roughness. Clean the wiper blades with washer fluid or waterapplied with a soft sponge or cloth. CHANGING THE WIPER BLADES 1. Pull the wiper blade and arm awayfrom the glass. 2. Squeeze the locking tabs to r...

When changing the air filter element, use only the air filter elementlisted. Refer to Motorcraft® Part Numbers in the Capacities and Specifications chapter. For EcoBoost equipped vehicles: When servicing the air cleaner, it isimportant that no foreign material enter the air induction system. Theengi...

3.5L V6 SHO engine 1. Release the clamps that secure the air filter housing cover. 2. Carefully separate the two halves of the air filter housing. 3. Remove the air filter element from the air filter housing. 4. Wipe the air filter housing and cover clean to remove any dirt ordebris and to ensure go...

Vertical Aim Adjustment 1. Park the vehicle directly in front of a wall or screen on a level surface,approximately 25 feet (7.6 meters) away. • (1) 8 feet (2.4 meters) • (2) Center height of lamp toground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height of the headlam...

4. Locate the vertical adjuster oneach headlamp. Using a Phillipsnumber 2 screwdriver, turn theadjuster either clockwise orcounterclockwise in order to adjustthe vertical aim of the headlamp. 5. Close the hood and turn off thelamps. HORIZONTAL AIM IS NOT REQUIRED FOR THIS VEHICLE AND ISNOT ADJUSTABL...

Replacing headlamp bulbs WARNING: Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause thebulb to break the next time the headlamps are operated. Note: If the bulb is accident...

Front parking lamp/turnsignal/sidemarker bulbs: 1. Make sure headlamp switch isin the off position, then open thehood. 2. Reach in behind the headlampassembly to access the bulb socketsand connectors. 3. Rotate the bulb socket counterclockwise and remove from the lampassembly. 4. Carefully pull the ...

Replacing supplemental park lamp bulbs Your vehicle is equipped with an LED supplemental park lamp. It isdesigned to last the life of the vehicle. If replacement is required, it isrecommended that you see your authorized dealer. BULB SPECIFICATION CHART Replacement bulbs are specified in the chart b...

• Spray Motorcraft Engine Shampoo and Degreaser on all parts thatrequire cleaning and pressure rinse clean. In Canada, use MotorcraftEngine Shampoo. • Never wash or rinse the engine while it is hot or running; water in therunning engine may cause internal damage. • Never wash or rinse any ignition c...

CLEANING THE INTERIOR WARNING: Do not use cleaning solvents, bleach or dye on the vehicle’s safety belts, as these actions may weaken the belt webbing. WARNING: On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents. Such products could contaminate the side...

• To check for compatibility, first test any cleaner or stain remover onan inconspicuous part of the leather. • Do not use household cleaning products, alcohol solutions,oil/petroleum-based leather conditioners, or solvents or cleanersintended specifically for rubber, vinyl and plastics. These produ...

Battery • Check and recharge as necessary. Keep connections clean. • If storing your vehicle for more than 30 days without recharging thebattery, it may be advisable to disconnect the battery cables to ensurebattery charge is maintained for quick starting. Note: If battery cables are disconnected, i...

TIRE CARE Information About Uniform Tire Quality Grading Tire Quality Grades apply to newpneumatic passenger car tires. The TireQuality Grades can be found whereapplicable on the tire sidewall betweentread shoulder and maximum sectionwidth. For example: • Treadwear 200 Traction AA Temperature A Thes...

The traction grades, from highest to lowest are AA, A, B, and C.The grades represent the tire’s ability to stop on wet pavement asmeasured under controlled conditions on specified government testsurfaces of asphalt and concrete. A tire marked C may have poortraction performance. Temperature A B C WA...

Information on P Type Tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) A. P: Indicates a tire, designated by the Tire ...

G. H: Indicates the tire’s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods oftime under a standard condition of load and inflation pressure. The tireson your vehicle may operate at different conditions for load and inflationpressure. The...

Additional Information Contained on the Tire Sidewall for LT TypeTires LT type tires have some additionalinformation beyond those of P typetires. These differences aredescribed below. Note: Tire Quality Grades do not apply to this type of tire. A. LT: Indicates a tire, designated by the Tire and Rim...

Information on T Type Tires T type tires have some additionalinformation beyond those of P typetires. These differences aredescribed below. T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Gradesdo not apply to thi...

INFLATING YOUR TIRES Safe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air pressurewithout appearing flat. Every day before you drive, check your tires. If one looks lower than theothers, use a tire gauge to check pressure o...

Maximum Inflation Pressure is the tire manufacturer’s maximum permissible pressure or the pressure at which the maximum loadcan be carried by the tire. This pressure is normally higher than themanufacturer’s recommended cold inflation pressure, which can be foundon the Safety Compliance Certificatio...

Note: Some spare tires operate at a higher inflation pressure than the other tires. For T-type mini-spare tires, see the Dissimilar Spare Tire and Wheel Assembly Information section. Store and maintain at 60 psi (4.15 bar). For full-size and dissimilar spare tires, see Dissimilar Spare Tire and Whee...

Damage Periodically inspect the tire treads and sidewalls for damage (such asbulges in the tread or sidewalls, cracks in the tread groove andseparation in the tread or sidewall). If damage is observed or suspected,have the tire inspected by a tire professional. Tires can be damagedduring off-road us...

Tire Replacement Requirements WARNING: Only use replacement tires and wheels that are the same size, load index, speed rating and type (such as P-metric versus LT-metric or all-season versus all-terrain) as those originallyprovided by Ford. The recommended tire and wheel size may be found oneither t...

Your vehicle is equipped with tires designed to provide a safe ride andhandling capability. Important: Remember to replace the wheel valve stems when the road tires are replaced on your vehicle. The two front tires or two rear tires should generally be replaced as apair. The tire pressure sensors mo...

If you feel a sudden vibration or ride disturbance while driving, or yoususpect your tire or vehicle has been damaged, immediately reduce yourspeed. Drive with caution until you can safely pull off the road. Stop andinspect the tires for damage. If a tire is under-inflated or damaged,deflate it, rem...

• Front-wheel drive/All-wheel drivevehicles (front tires at left ofdiagram) Sometimes irregular tire wear can be corrected by rotating the tires. USING SUMMER TIRES Your Taurus SHO may be equipped with summer tires to providesuperior performance on wet and dry roads. Summer tires do not havethe Mud ...

The tires on your vehicle may have all-weather treads to provide tractionin rain and snow. However, in some climates, you may need to use snowtires and chains. If you need to use chains, it is recommended that steelwheels (of the same size and specifications) be used, as chains may chipaluminum whee...

Changing Tires with a Tire Pressure Monitoring System Note: Each road tire is equipped with a tire pressure sensor locatedinside the tire and wheel assemblycavity. The pressure sensor isattached to the valve stem. Thepressure sensor is covered by thetire and is not visible unless thetire is removed....

Low tirepressurewarning light Possible cause Customer action required Solid warninglight Tire(s)under-inflated 1. Make sure tires are at the properpressure. See Inflating Your Tires in this chapter.2. After inflating your tires to themanufacturer’s recommendedpressure as shown on the Tire Label(loca...

When Inflating Your Tires When putting air into your tires (such as at a gas station or in yourgarage), the tire pressure monitoring system may not respondimmediately to the air added to your tires. It may take up to two minutes of driving over 20 mph (32 km/h) for thelight to turn off after you hav...

If you get a flat tire while driving, do not apply the brake heavily.Instead, gradually decrease your speed. Hold the steering wheel firmlyand slowly move to a safe place on the side of the road. Have a flat serviced by an authorized dealer in order to prevent damageto the system sensors. See Tire P...

Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability • All...

Tire Change Procedure WARNING: When one of the front wheels is off the ground, the transmission alone will not prevent your vehicle from moving or slipping off the jack, even if the transmission is in park (P). WARNING: To help prevent your vehicle from moving when you change a tire, be sure to plac...

TEMPORARY MOBILITY KIT (IF EQUIPPED) Note: The temporary mobility kit sealant compound in the canister is to be used for one tire only. See your Ford authorized dealer for additionalreplacement sealant canisters. Your vehicle may be equipped with a temporary mobility kit (located inthe spare tire we...

Do not attempt to repair punctures larger than 1 ⁄ 4 inch (6 millimeters) or damage to the tire’s sidewall. The tire may not completely seal. Loss of air pressure may adversely affect tire performance. For thisreason: • Note: Do not drive the vehicle above 50 mph (80 km/h). • Note: Do not drive furt...

• Only use the temporary mobility kit when the ambient temperature isbetween -40°F (-40°C) and 158°F (70°C). • Only use the sealing compound before the use by date. The use bydate is on the lower right hand corner of the label located on thesealant canister (bottle). Check the use by date regularly ...

Preparation Park the vehicle in a safe, level and secure area, away from movingtraffic. Turn the hazard lights on. Apply the parking brake and turn theengine off. Inspect the flat tire for visible damage. Sealant compound contains latex. To avoid any allergic reactions, use thenon-latex gloves locat...

Second Stage: Checking Tire Pressure WARNING: The power plug may get hot after use and should be handled carefully while unplugging. Check the air pressure of your tires as follows:1. Remove the valve cap from the tire valve.2. Unhook the black hose from the side of the compressor and fastenfirmly o...

Be sure to check the sealantcompound’s use-by date regularly.The use-by date is on the lowerright hand corner of the labellocated on the sealant canister. The sealant canister should be replaced after four years. TECHNICAL SPECIFICATIONS Wheel Lug Nut Torque Specifications WARNING: When a wheel is i...

ENGINE SPECIFICATIONS Engine 3.5L V6 engine 3.5L V6 SHO engine 2.0L EcoBoost engine Cubic inches 214 214 122 Required fuel See Octane recommendations in the Fuel and Refueling chapter. Firing order 1–4–2–5–3–6 1–4–2–5–3–6 1-3-4-2 Ignitionsystem Coil on plug Coil on plug Coil on plug Spark pluggap 0....

VEHICLE IDENTIFICATION NUMBER The vehicle identification numberis located on the driver’s sideinstrument panel. Please note that in the graphic,XXXX is representative of yourvehicle identification number. The Vehicle Identification Number (VIN) contains the followinginformation: A. World manufacture...

ACCESSORIES For a complete listing of the accessories that are available for yourvehicle, please contact an authorized dealer or visit our online store at www.Accessories.Ford.com (United States only). Ford Motor Company will repair or replace any properly authorizeddealer-installed Ford Genuine Acc...

Peace of mind • Remote start • Wheel locks • Locking fuel plug for capless fuel system • Bumper mounted parking sensors* • Vehicle security *The accessory manufacturer designs, develops and therefore warrantsFord Licensed Accessories, and does not design or test these accessoriesto Ford Motor Compan...

FORD ESP EXTENDED SERVICE PLANS PROTECT YOURSELF FROM THE RISING COST OF VEHICLE REPAIRSWITH A FORD EXTENDED SERVICE PLAN. SERVICE PLANS (U.S. only) More than 32 Million Ford and Lincoln owners have discovered thepowerful protection Ford ESP. It is the only extended service planbacked by Ford Motor ...

Interest Free Financing Options Available Take advantage of our interest free installment payment plan. Just a 10%down payment will provide you with an affordable, no interest, no feepayment program. Complete the information below and mail to: Ford ESPPO Box 8072Royal Oak Michigan 48068-0039 To lear...

GENERAL INFORMATION Radio Frequencies and Reception Factors AM and FM frequencies are established by the Federal CommunicationsCommission (FCC) and the Canadian Radio and TelecommunicationsCommission (CRTC). Those frequencies are: AM: 530, 540–1700, 1710 kHz FM: 87.9–107.7, 107.9 MHz Radio reception...

MP3 Track and Folder Structure Audio systems capable of recognizing and playing MP3 individual tracksand folder structures work as follows: • There are two different modes for MP3 disc playback: MP3 trackmode (system default) and MP3 folder mode. • MP3 track mode ignores any folder structure on the ...

MyFord® SYSTEM WARNING: Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus offthe road. Your primary responsibility is the safe operation of yourvehicle. We recommend agai...

L. MENU: Press this button to access different audio system features. See Menu structure later in this section. M. PHONE: Press this button to access the phone features of the SYNC system. See the SYNC chapter for more information. N. AUX: Press this button to access your auxiliary input jack or swi...

SIRIUS Channel Guide Select to view available satellite radiochannels. Press OK to open a list of the following options for this channel: TuneChannel, Skip Channel or Lock Channel. Onceyou skip or lock a channel, you can only accessit by pressing Direct and entering the channelnumber. Locking or unl...

E. SEEK, Reverse and Fast Forward: • In radio mode, select a frequency band and press one of thesebuttons. The system stops at the first station it finds in that direction. • In Sirius mode, press these buttons to select the previous or nextchannel. If a specific category is selected (such as Jazz, ...

Potential station issues Issue Cause Action Cannot access HD2 orHD3 multicast channelwhen recalling apreset or from a directtune. The previously storedmulticast preset ordirect tune is notavailable in yourcurrent reception area. No action required.The station is notavailable in yourcurrent location....

When using SYNC: • Do not operate playing devices if the power cords or cables are broken,split or damaged. Place cords and cables out of the way, so they do notinterfere with the operation of pedals, seats, compartments or safedriving abilities. • Do not leave playing devices in your vehicle during...

Adjusting the Interaction Level Push the voice icon; when prompted, say “Voice settings”, thenany of the following: When you say: The system: “Interaction mode standard” Provides more detailed interaction and guidance. “Interaction mode advanced” Provides less audible interaction and more tone promp...

Helpful Hints • Make sure the interior of the vehicle is as quiet as possible. Windnoise from open windows and road vibrations may prevent the systemfrom correctly recognizing spoken commands. • After pressing the voice icon, wait until after the tone sounds andListening appears before saying a comm...

Making Calls Press the voice icon and when prompted say:1. Say “Call <name>” or “Dial”, then the desired number.2. When the system confirms the number, say “Dial” again to initiate the call. To erase the last spoken digit, say “Delete” or press the left arrowbutton. To erase all spoken digits,...

Accessing Features through the Phone Menu SYNC’s phone menu allows you to redial a number, access your callhistory and phone book and send text messages as well as access phoneand system settings. You can also access advanced features, such as 911Assist, Vehicle Health Report and SYNC Services.1. Pr...

When you select: You can: Text Message 1 Enables you to send, download and delete textmessages. Phone Settings 1 Allows you to view your phone’s status, set ringtones, select your message notification, changephone book entries and automatically downloadyour cellular phone among other features. SYNC ...

Receiving a Text Message Note: This is a phone-dependent feature. Your phone must support downloading text messages using Bluetooth to receive incoming textmessages. Note: Forwarding a text message is a speed-dependent feature and can only be done when the vehicle is traveling at 3 mph (5 km/h) or l...

Note: SYNC does not automatically download all of your unread text messages at every ignition cycle (as it does with call history andphonebook if automatic download is set to on). Return exits the current menu when you press OK. If you select Send Text Message? : 1. Press OK to select. If the system...

When you select: You can: Modify Phonebook Modify the contents of your phone book(such as add, delete, download). Press OK toselect and scroll between: Add Contacts: Press OK to add more contactsfrom your phone book. Push the desiredcontact(s) on your phone. See your phone’suser guide on how to push...

System Settings System Settings provide access to your Bluetooth Devices andAdvanced menu features. Use the arrow buttons to scroll through themenu options. The Bluetooth Devices menu allows you to add, connect, delete and seta phone as primary as well as turn your Bluetooth feature on and off. The ...

If you select: You can: Set Bluetooth On/Off Turn the Bluetooth feature on and off.Press OK and scroll to toggle between On andOff. When the desired selection is chosen,press OK. Note: Turning Bluetooth off disconnects all Bluetooth devices and deactivates allBluetooth features. Delete Device Delete...

SYNC APPLICATIONS AND SERVICES (IF EQUIPPED) Note: In order for the following features to work, your cellular phone must be compatible with SYNC. To check your phone’s compatibility, visitwww.SYNCMyRide.com, www.SYNCMyRide.ca or www.syncmaroute.ca. • SYNC Services (if equipped, United States only): ...

Vehicle Health Report WARNING: Always follow scheduled maintenance instructions, regularly inspect your vehicle, and seek repair for any damage or problem you suspect. Vehicle Health Report supplements, but cannotreplace normal maintenance and vehicle inspection. Vehicle HealthReport only monitors c...

To run a report using the phone button:1. Press the phone button to enter Phone Menu.2. Scroll until Vehicle Health is selected and press OK.3. Scroll to select from the following options: Vehicle Health Report options User Preferences:Press OK to selectand enter the menu.Scroll to select from: Auto...

3. While on an active route, you can select or say “Route summary” or “Route status” to view the Route Summary turn list or the RouteStatus ETA. You can also turn voice guidance on or off, cancel theroute or update the route. If you miss a turn, SYNC automatically asks if you want the routeupdated. ...

“USB” “Search song <name>” 1,3 “Search track <name>” 1,3 “Shuffle off” “Shuffle on” “Similar music” “What’s playing?” 1 “<name>” is a dynamic listing, meaning that it could be the name of any desired group, artist, etc. 2 Voice commands which are only available in folder mode. 3 Vo...

Voice command guide “Refine” This allows you to make your previouscommand more specific. For example, if youasked to search and play all music by acertain artist, you could then say “refinealbum” and choose a specific album from thelist to view. If you then select Play, the systemonly plays music fr...

When you select: You can: Select Source SYNC USB: Press OK to access music plugged into your USB port. You can also plugin devices to charge them (if supported byyour device). Once connected, the systemindexes any readable media files. (The timerequired to complete this depends on thesize of the med...

When you select: You can: Explore USB Explore all supported digital media on yourmedia device connected to the USB port.You can only view media content which iscompatible with SYNC; other files saved arenot visible.Press OK to select. Then scroll to exploreindexed media on your flash drive. Similar ...

Advanced Menu Options This menu allows you to access settings such as prompts, language,performing a master reset as well as returning to factory defaults.1. Press AUX and then MENU to access the Media Menu.2. Scroll until System Settings appears and select OK.3. Scroll until Advanced appears.4. Pre...

When you select: You can: Master Reset Completely erase all information stored onSYNC (all phonebook, call history, textmessages and all paired devices) and returnto the factory default settings. Application Download new software applications(if available) and then load the desiredapplications throu...

Vehicle Health Report and SYNC Services (Traffic, Directions and Information) issues Issue Possible cause(s) Possible solution(s) I am unable tosubmit a report. • This could be due to your phone’scompatibility, OR • Bad signal strength, OR • Your phone may not be activated onthe website. • Update yo...

INTRODUCTION WARNING: Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus offthe road. Your primary responsibility is the safe operation of yourvehicle. We recommend agains...

SETTINGS Press to select any of the following: • Clock • Display • Sound • Vehicle • Settings • Help HOME Press to access your home screen. Depending on your vehicle’s optionpackage and software, your screens may vary in appearance from thedescriptions in this section. Your features may also be limi...

Support The SYNC support team is available to help you with any questions youcannot answer on your own. Monday-Saturday, 8:30am-9:00pm EST. Sunday, 10:30am-7:30pm EST. In the United States, call: 1–800–392–3673. In Canada, call: 1–800–565–3673. Times are subject to change due to holidays. Safety Inf...

What Can I Say? To access the available voice commands for the current session, do oneof the following: • During a voice session, press the Help icon ( ? ) in the lower left status bar of the screen. • Say, “What can I say?” for an on-screen listing of the possible voicecommands associated with your...

Press the voice icon on the steering wheel. When prompted,you can say: “BROWSE” within devices “Browse” * “Browse <league> games” ** “Browse <Sirius category> channels” ** “Browse Sirius channel guide” ** “Browse SD card” “Browse USB” “Help” * If you have said “Browse”, you can then say ...

are available at the top level of the voice session no matter whichcurrent audio source you are listening to (such as a USB device or Siriussatellite radio). Note: This is only available when your MyFord Touch system language is set to North American English. “AM <530 - 1710>” “FM <87.9 – 1...

HD Radio Reception and Station Troubleshooting Potential Reception Issues Reception area If you are listening to a multicast station andyou are on the fringe of the reception area, thestation may mute due to weak signal strength. If you are listening to HD1, the system switchesback to the analog bro...

Radio Voice Commands If you are listening to the radio, press the voice button on thesteering wheel control. When prompted, say any of thecommands in the following chart. If you are not listening to the radio, press the voice button and, after thetone, say “Radio”, then any of the commands in the fo...

Sirius Satellite Radio (If Activated) Press the lower left corner of the touchscreen, then select the SIRIUS tab. Presets Save a channel by pressing and holding one of the memory preset areas.There is a brief mute while the radio saves the channel. Sound returnswhen finished. ALERT Save the current ...

Satellite Radio Voice Commands If you are listening to Sirius satellite radio, press the voicebutton on the steering wheel control. When prompted, say anyof the commands in the following chart. If you are not listening to Sirius satellite radio, press the voice buttonand, after the tone, say “Sirius...

“TUNE” “SAT 2 preset <#>” “SAT 3” “SAT 3 preset <#>” “Help” Sirius Satellite Radio Information Note: Sirius reserves the unrestricted right to change, rearrange, add or delete programming including canceling, moving or adding particularchannels, and its prices, at any time, with or witho...

Potential satellite radio reception issues Station overload When you pass a ground-basedbroadcast-repeating tower, a stronger signalmay overtake a weaker one and the audiosystem may mute. Satellite radiosignal interference Your display may show ACQUIRING . . . toindicate the interference and the aud...

Sirius troubleshooting tips Radio display Condition Possible action Updating. Update of channelprogramming inprogress. No action required.The process may takeup to three minutes. Call SIRIUS1–888–539–7474. Your satellite service isno longer available. Contact Sirius at1-888-539-7474 toresolve subscr...

Options Sound Settings allows you to adjust settings for: • Bass • Midrange • Treble • Balance and Fade • DSP (Digital Signal Processing) • Occupancy Mode • Speed Compensated Volume. Note: Your vehicle may not have all these sound settings. Compression allows you to turn the compression feature on a...

More Info displays information such as current track, artist name, album and genre. Options allows you to view and adjust various media settings. • Sound Settings allows you to adjust settings for: • Bass • Midrange • Treble • Balance and Fade • DSP (Digital Signal Processing) • Occupancy Mode • Spe...

“BROWSE” “All podcasts” “Video <name>” * “All songs” “Video playlist <name>” * “All TV shows” * “Video podcast <name>” * “All video playlists” * “Help” * This command is only available in USB mode and are device-dependent. Supported Media Players, Formats and Metadata Information S...

PHONE A. Phone B. Quick Dial C. Phonebook D. History E. Messaging F. Settings Hands-free calling is one of the main features of SYNC. Once you pairyour phone, you can access many options using the touchscreen or voicecommands. While the system supports a variety of features, many aredependent on you...

3. If you are prompted to enter a PIN on your device, it does not support Secure Simple Pairing. To pair, enter the PIN displayed onthe touchscreen. Skip the next step. 4. When prompted on your phone’s display, confirm that the PIN provided by SYNC matches the PIN displayed on your cellular phone. 5...

3. Choose from the following: • Listen (speaker icon) • Dial • Send Text • View • Delete. Composing a Text Message Note: This is a speed-dependent feature. It is unavailable when your vehicle is traveling at speeds over 3 mph (5 km/h). Note: Downloading and sending text messages using Bluetooth are ...

Receiving a Text Message When a new message arrives, an audible tone sounds and the screendisplays a pop-up with the caller name and ID, if supported by yourphone. You can press: • View to view the text message. • Listen for SYNC to read the message to you. • Dial to call the contact. • Ignore to ex...

Internet Data Connection If your phone is compatible, use this screen to adjust your internet dataconnection. Select to make your connection profile with the personalarea network or to turn off your connection. You can also choose toadjust your settings or have the system always connect, never conne...

Connecting to SYNC Services Using Voice Commands Press the voice button on the steering wheel controls. 1. When prompted, say “Services”. This initiates an outgoing call to SYNC Services using your paired and connected Bluetooth-enabledcellular phone. 2. Once you connect to the service, follow the v...

SYNC Services quick tips Portable Your subscription is associated with yourBluetooth-enabled cellular phone number,not your VIN (Vehicle Identification Number).You can pair and connect your phone to anyvehicle equipped with SYNC Services andcontinue enjoying your personalized services. SYNC Services...

Sirius Travel Link Voice Commands Note: In order to use Sirius Travel Link, your vehicle must be equipped with navigation and your navigation SD card must be in the SD card slot. Press the voice button on the steering wheel controls and, whenprompted, say any of the following: Travel Link voice comm...

Setting 911 Assist On If your vehicle is equipped with Navigation, touch thei (Information) button to access these features. If your vehicleis not equipped with Navigation, touch the corner of the touchscreen with the green tab. Press Apps > 911 Assist, > On. You can also access 911 Assist by:...

Note: In order to allow a break-in period for your vehicle, you may not be able to create a Vehicle Health Report until your vehicle odometer hasreached 200 miles. Note: Cellular phone and SMS charges may apply when making a report. Register for Vehicle Health Report and set your report preferences ...

SETTINGS A. Clock B. Display C. Sound D. Vehicle E. Settings F. Help Under this menu, you can set your clock, access and adjust thedisplay, sound and vehicle settings as well as access settings forspecific modes or the help feature. Clock Note: You cannot manually set the date. Your vehicle’s GPS do...

You can also turn the outside air temperature display on and off. Itappears at the top center of the touchscreen, next to the time and date. The system automatically saves any updates you make to the settings. Display You can adjust the touchscreen display through the touchscreen or bypressing the v...

Only the photograph(s), which meets the following conditions, display: • Compatible file formats are as follows: .jpg, .gif, .png, .bmp. • Each file must be 1.5 MB or less. • Recommended dimensions: 800 x 384. Sound Press the Settings icon > Sound, then select from the following: Sound Settings B...

Door Keypad Code To change the keypad code for your keyless entry keypad system:1. Press the Settings icon > Vehicle > Door Keypad Code. 2. Enter your current factory code, then, when prompted, enter your new code. Rear View Camera This menu allows you to access settings for your rear view cam...

Navigation Press the Settings icon > Settings > Navigation, then select from the following: Navigation Map Preferences Turn breadcrumbs on and off. Have the system display your turn list top tobottom or bottom to top. Turn the Parking POI notification on and off. Route Preferences Preferred Ro...

Phone Phone Ringer Select the type of notification for phone calls- ring tone, beep, text to speech, or have it besilent. Text MessageNotification Select the type of notification for textmessages - alert tone, beep, text to speech, orhave it be silent. Internet DataConnection If compatible with your...

Wireless & Internet Wi-Fi Settings Wi-Fi Network (Client) Mode turns the Wi-Fi feature on and off in your vehicle. Makesure you turn it on for connectivity purposes. Choose a Wireless Network allows you to use a previously stored wireless network. You cancategorize by alphabetical listing, prior...

Wireless & Internet Bluetooth Settings Shows you the currently paired devices as wellas giving you your typical Bluetooth options toconnect, disconnect, set as favorite, delete andadd device. Bluetooth is a registered trademarkof the Bluetooth SIG. PrioritizeConnectionMethods Choose your connect...

Help Software Licenses View the licenses for any software andapplications installed on your system. DrivingRestrictions Certain features are not accessible when yourvehicle is moving. 911 Assist Turn on and turn off the 911 Assist feature.See 911 Assist in the SYNC applications and services section....

F. A/C: Touch to turn the air conditioning on or off. • Use with recirculated air to improve cooling performance andefficiency. • Engages automatically in MAX A/C, defrost and floor/defrost. G. AUTO: Touch to engage automatic operation, then set the temperature using the temperature control. The sys...

“TEMPERATURE” “High” “Low” “<15.5–29.5> degrees” “<60–85> degrees” “Help” NAVIGATION SYSTEM (IF EQUIPPED) Note: The navigation SD card must be in the SD card slot to operate the navigation system. If you need a replacement SD card, see yourauthorized dealer. Note: The SD card slot is spr...

For restaurants, cityseekr can provide information, such as star rating,average cost, review, handicap access, hours of operation, and websiteaddress. For hotels, cityseekr can provide information, such as star rating, pricecategory, review, check-in and check-out times, hotel service icons andwebsi...

Navigation Preferences Guidance Prompts allows you to choose to have the system use Voice & Tones or Tone Only on your programmed route. Auto - Fill State/Province allows you have the system automatically fill in the state and province based on the information already entered intothe system. Tur...

3D landmarks appear as clear, visible objects that are typically recognizable and have a certain tourist value. The 3D landmarks appearin 3D map mode only. Coverage varies, and improves with updated mapreleases. Change the appearance of the mapdisplay by repeatedly pressing thearrow button in the up...

then synchronizes with vehicle speed. The slower your vehicle istraveling, the farther in the map zooms in; the faster your vehicle istraveling, the farther the map zooms out. To turn the feature off, justpress the + or - button again. In 3D mode, rotate the map view by swiping your finger across th...

Next maneuver point indicates the location of the next turn on the planned route. No GPS symbol indicates that insufficient GPS satellite signals are available for accurate map positioning. This icon may displayunder normal operation in an area with poor GPS access. Quick-touch Buttons When in map m...

3 If you have said the command, “Navigation”, you may say any of the above commands or commands in the following Navigation chart. “DESTINATION” “<nametag>” “<POI category>” “Favorites” “Home” “Intersection” “Nearest <POI category>” “Nearest POI” “Play nametags” “POI category” “Pre...

GENERAL INFORMATION SYNC® End User License Agreement (EULA) • You have acquired a device (“DEVICE”) that includes software licensed by Ford Motor Company and its affiliates (“FORD MOTORCOMPANY”) from an affiliate of Microsoft Corporation (“MS”). Thoseinstalled software products of MS origin, as well...

SOFTWARE’s ability to use WMDRM to play or copy protectedcontent. This action does not affect unprotected content. When yourDEVICE downloads licenses for protected content, you agree thatMicrosoft may include a revocation list with the licenses. Contentowners may require you to upgrade the SOFTWARE ...

suppliers. The SOFTWARE is licensed, not sold. You may not copy theprinted materials accompanying the SOFTWARE. All title and intellectualproperty rights in and to the content which may be accessed through useof the SOFTWARE is the property of the respective content owner andmay be protected by appl...

• THERE ARE NO WARRANTIES OTHER THAN THOSE THAT MAY EXPRESSLY BE PROVIDED FOR YOUR NEW VEHICLE. Adobe Contains Adobe® [Flash® Player] or [AIR®] technology by AdobeSystems Incorporated. This [Licensee Product] contains [Adobe® Flash®Player] [Adobe® AIR®] software under license from Adobe SystemsIncor...

General operation Voice Command Control Functions within the Windows Automotive-based system may beaccomplished using only voice commands. Using voice commands whiledriving allows you to operate the system without removing your handsfrom the wheel. Prolonged Views of Screen Do not access any functio...

in which case you and all other parties shall immediately cease all use ofthe TeleNav Software. Notwithstanding the foregoing, TeleNav mayassign this Agreement to any other party at any time without notice,provided the assignee remains bound by this Agreement. 8. Miscellaneous 8.1 This Agreement con...

9. Other Vendors Terms and Conditions The TeleNav Software utilizes map and other data licensed toTeleNav by third party vendors for the benefit of you and other endusers. This Agreement includes end-user terms applicable to thesecompanies (included at the end of this Agreement), and thus youruse of...

TERMS AND CONDITIONS License Limitations on Use: You agree that your license to use this Data is limited to and conditioned on use for solely personal,noncommercial purposes, and not for service bureau, timesharing orother similar purposes. Except as otherwise set forth herein, you agreenot to other...

No Warranty: This Data is provided to you “as is”, and you agree to use it at your own risk. NT and its licensors (and their licensors and suppliers)make no guarantees, representations or warranties of any kind, express orimplied, arising by law or otherwise, including but not limited to, content,qu...

Gracenote® Copyright CD and music — related data from Gracenote, Inc., copyright 娀 2000–2007 Gracenote. Gracenote Software, copyright 娀 2000–2007 Gracenote. This product and service may practice one or more of thefollowing U.S. Patents #5,987,525; #6,061,680; #6,154,773, #6,161,132,#6,230,192, #6,23...

Vehicle with SYNC only FCC ID: KMHSG1G1 IC: 1422A-SG1G1 Vehicle with SYNC and MyFord Touch or MyLincoln Touch FCC ID: KMHSYNCG2 IC: 1422A-SYNCG2 This device complies with Part 15 of the FCC Rules and with RSS-210 ofIndustry Canada. Operation is subject to the following two conditions:(1) This device...

GENERAL MAINTENANCE INFORMATION Why Maintain Your Vehicle? Carefully following the maintenance schedule helps protect against majorrepair expenses resulting from neglect or inadequate maintenance andmay help to increase the value of your vehicle when you sell or trade it.Keep all receipts for comple...

Convenience Many dealerships have extended evening and Saturday hours to makeyour service visit more convenient and they offer one stop shopping.They can perform any services that are required on your vehicle, fromgeneral maintenance to collision repairs. Note: Not all dealers have extended hours or...

Additives and Chemicals Ford Motor Company recommended additives and chemicals are listedin the owner manual and in the Ford Workshop Manual. Additionalchemicals or additives not approved by Ford Motor Company are notrecommended as part of normal maintenance. Please consult yourwarranty information....

Normal scheduled maintenance * At every oil changeinterval as indicated bythe information display Change engine oil and filter. ** Rotate tires, inspect tire wear and measuretread depth. Perform multi-point inspection(recommended). Inspect automatic transmission fluid level(if equipped with dipstick...

Other maintenance items 1 Every 20000 miles(32000 km) Replace cabin air filter (if equipped). Every 30000 miles(48000 km) Replace climate-controlled (heated andcooled) seat filter 2 . Replace engine air filter. At 100000 miles(160000 km) Change engine coolant. 3 Every 100000 miles(160000 km) Replace...

Maintenance Schedule Log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ...

Extensive idling or low-speed driving for long distances as in heavy commercial use (such as delivery, taxi, patrol car or livery) Every 30000 miles(48000 km) Change automatic transmission fluid(except Focus). Every 60000 miles(96000 km) Replace spark plugs. Operating in dusty or sandy conditions su...

Special Operating Condition Log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D A...

EXCEPTIONS There are several exceptions to the Normal Schedule. They are listedbelow: Normal vehicle axle maintenance: Rear axles and power take-off (PTO) units with synthetic fluid and light-duty trucks equipped withFord-design axles are lubricated for life; do not check or change fluidunless a lea...

Edge/MKX AWD only: Vehicles operating off-road in sand during high ambient temperatures must replace the AWD PTU (All-wheel drivePower Transfer Unit) lube every 20000 miles (32000 kilometers). Engine air filter & cabin air filter replacement: Engine air filter and cabin air filter life is depend...

911 Assist™ ......................405, 480 A ABS (see Brakes) .....................196 Accessing and using yourUSB port ....................................458 Accessing call history/phonebook during active call .............394 Accessing your calendar ..........479 Accessing your media menufeatures...