Ford 2014 Expedition v.1- User Manual

Ford Motor Company, Ford of Canada, and service and repair facilitiesmay access or share among them data for vehicle improvement purposes.For U.S. only (if equipped), if you choose to use the SYNC® VehicleHealth Report, you consent that certain diagnostic information may alsobe accessed electronical...

they have access to the vehicle or the EDR. Ford Motor Companyand Ford of Canada do not access event data recorderinformation without obtaining consent, unless pursuant to courtorder or where required by law enforcement, other governmentauthorities or other third parties acting with lawful authority...

PERCHLORATE MATERIAL Note: Certain components in your vehicle, such as airbag modules, safety belt pretensioners, and remote control batteries, may containperchlorate material. Special handling may apply for service or vehicleend of life disposal. See www.dtsc.ca.gov/hazardouswaste/perchlorate formo...

Warranty on Replacement Parts Genuine Ford and Motorcraft replacement parts are the onlyreplacement parts that benefit from a Ford Warranty. Damage causedto your vehicle as a result of the failure of non-Ford parts may not becovered by the Ford Warranty. For additional information, see the termsand ...

MOBILE COMMUNICATIONS EQUIPMENT Using mobile communications equipment is becoming increasinglyimportant in the conduct of business and personal affairs. However, youmust not compromise your own or others’ safety when using suchequipment. Mobile communications can enhance personal safety andsecurity ...

GENERAL INFORMATION See the following sections for directions on how to properly use safetyrestraints for children. WARNING: Always make sure your child is secured properly in a device that is appropriate for their height, age and weight. Child safety restraints must be bought separately from your v...

Recommendations for Safety Restraints for Children Child size, height, weight, orage Recommendedrestraint type Infantsortoddlers Children weighing 40 lb (18 kg) orless (generally age four oryounger). Use a child safety seat(sometimes called aninfant carrier,convertible seat, ortoddler seat). Smallch...

CHILD SEAT POSITIONING WARNING: Airbags can kill or injure a child in a child seat. Never place a rear-facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move thevehicle seat upon which the child seat is installed all the way back.When poss...

WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the riskof injury or death in a crash. WARNING: To avoid risk of injury, do not leave children or pets unattende...

BOOSTER SEATS WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the riskof injury or death in a crash. Use a belt-positioning booster seat for children who have o...

Types of Booster Seats • Backless booster seats If your backless booster seat has a removable shield, remove the shield.If a vehicle seating position has a low seat back or no head restraint, abackless booster seat may place your child’s head (as measured at thetops of the ears) above the top of the...

• Keep the buckle release button pointing up and away from the safetyseat, with the tongue between the child seat and the release button,to prevent accidental unbuckling. • Place the vehicle seat upon which the child seat will be installed inthe upright position. • Put the safety belt in the automat...

3. While holding the shoulder andlap belt portions together, routethe tongue through the childseat according to the child seatmanufacturer’s instructions. Be surethe belt webbing is not twisted. 4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingf...

Using Lower Anchors and Tethers for CHildren (LATCH) WARNING: Never attach two child safety seats to the same anchor. In a crash, one anchor may not be strong enough to hold two child safety seat attachments and may break, causing serious injuryor death. The LATCH system is composed of three vehicle...

Your vehicle has LATCH lower anchors for child seat installation at theseating positions marked with the child seat symbol. The LATCH anchors are located at the rear section of the rear seatbetween the cushion and seat back, below the locator symbols on theseat back. Follow the child seat manufactur...

Each time you use the safety seat, check that the seat is properlyattached to the lower anchors and tether anchor, if applicable. Tug thechild seat from side to side and forward and back where it is secured tothe vehicle. The seat should move less than one inch when you do thisfor a proper installat...

• Second row bucket seats Attach the tether strap only to the appropriate tether anchor as shown.The tether strap may not work properly if attached somewhere otherthan the correct tether anchor. Once the child safety seat has been installed using either the safety belt,the lower anchors of the LATCH...

2. Locate the correct anchor for the selected seating position. • Second row outboard seatingpositions • Second row center seatingposition (if equipped) 3. Grasp the tether strap andposition it to the seat frame. 32 Child Safety 2014 Expedition (exd) Owners Guide gf, 1st Printing, June 2013USA (fus)

4. Rotate the tether strap, and clipthe tether strap to the anchor onthe seat frame. 5. Rotate the tether strap clip. 6. Tighten the child safety seat tether strap according to themanufacturer’s instructions. Third row center seating position 1. Route the child safety seat tether strap over the back...

2. Locate the anchor webbing loop for the seating position. • You may need to pull back the top of the hinged panel along thebottom of the seat back to access the tether anchor. 3. Clip the tether strap through the anchor loop as shown. If the tetherstrap is clipped incorrectly, the child safety sea...

If your child restraint system is equipped with a tether strap, and thechild restraint manufacturer recommends its use, Ford also recommendsits use. CHILD SAFETY LOCKS When these locks are set, the rear doors cannot be opened from theinside. The childproof locks are located onthe rear edge of each r...

PRINCIPLES OF OPERATION WARNING: Always drive and ride with your seat back upright and the lap belt snug and low across the hips. WARNING: To reduce the risk of injury, make sure children sit where they can be properly restrained. WARNING: Never let a passenger hold a child on his or her lap while t...

FASTENING THE SAFETY BELTS The front outboard and rear safety restraints in your vehicle arecombination lap and shoulder belts. 1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until you hear a snap and feelit latch. Make sure the tongue i...

Pregnant women should alwayswear their safety belts. The lap beltportion of a combination lap andshoulder belt should be positionedlow across the hips below the bellyand worn as tight as comfort willallow. The shoulder belt should bepositioned to cross the middle ofthe shoulder and the center of the...

Automatic Locking Mode In this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to remove any slack in the shoulder belt. The automaticlocking mode is not available on the driver safety belt. When to Use the Automatic Locking Mode This mode should be used any time a ch...

SAFETY BELT HEIGHT ADJUSTMENT WARNING: Position the safety belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat beltand increase the risk of injury in a crash. Adjust the height of the s...

To adjust the comfort guide: 1. Slip the shoulder belt into thebelt guide (the portion of the beltbetween the latch tongue and theD-ring, not the portion where thebelt exits from the quarter trimpanel). 2. Slide the guide up or down along the webbing so that the belt iscentered on the occupant’s sho...

Deactivating and Activating the Belt-Minder® Feature WARNING: While the design allows you to deactivate your Belt-Minder, this system is designed to improve your chances of being safely belted and surviving an accident. We recommend you leavethe Belt-Minder system activated for yourself and others w...

CHILD RESTRAINT AND SAFETY BELT MAINTENANCE Inspect the vehicle safety belts and child safety seat systems periodically tomake sure they work properly and are not damaged. Inspect the vehicle andchild seat safety belts to make sure there are no nicks, tears or cuts. Replaceif necessary. All vehicle ...

RESTRAINT SAFETY SYSTEM The Restraint Safety System provides an improved overall level of frontalcrash protection to front seat occupants and is designed to help furtherreduce the risk of airbag-related injuries. The system is able to analyzedifferent occupant conditions and crash severity before ac...

DRIVER AND PASSENGER AIRBAGS WARNING: Never place your arm or any objects over an airbag module. Placing your arm over a deploying airbag can result in serious arm fractures or other injuries. Objects placed on or over theairbag inflation area may cause those objects to be propelled by theairbag int...

Proper Driver and Front Passenger Seating Adjustment WARNING: The National Highway Traffic Safety Administration recommends a minimum distance of at least 10 inches (25 centimeters) between an occupant’s chest and the driver airbagmodule. Failure to follow this could seriously increase the risk of i...

SIDE AIRBAGS WARNING: Do not place objects or mount equipment on or near the airbag cover, on the side of the seat backs (of the front seats), or in front seat areas that may come into contact with adeploying airbag. Failure to follow these instructions may increase therisk of personal injury in the...

The system consists of thefollowing: • a label or embossed side panelindicating that side airbags arefound on your vehicle • side airbags located inside theseat back of the driver and frontpassenger seats • crash sensors and monitoring system with readinessindicator. See Crash Sensors and Airbag Ind...

Children 12 years old and under should always be properly restrained inthe rear seats. The Safety Canopy will not interfere with childrenrestrained using a properly installed child or booster seat because it isdesigned to inflate downward from the headliner above the doors alongthe side window openi...

If any of these things happen, even intermittently, have the supplementalrestraint system serviced at an authorized dealer immediately. Unlessserviced, the system may not function properly in the event of a crash. The safety belt pretensioners and the airbag supplemental restraintsystem are designed...

GENERAL INFORMATION ON RADIO FREQUENCIES This device complies with part 15 of the FCC Rules and with IndustryCanada license-exempt RSS standard(s). Operation is subject to thefollowing two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference...

Note: Your vehicle’s keys were issued with a security label thatprovides important vehicle key cutinformation. Keep the label in a safeplace for future reference. Replacing the Battery Note: Refer to local regulations when disposing of transmitter batteries. Note: Do not wipe off any grease on the b...

Memory Feature (If Equipped) The feature allows the remote control to recall the driver seat, powermirrors and power adjustable foot pedals memory positions. Press the unlock button on the remote control to recall the memorypositions. If the easy entry and exit feature is enabled, the seat will move...

REPLACING A LOST KEY OR REMOTE CONTROL You can purchase replacement or additional keys or remote controls froman authorized dealer. A dealer can program the transmitters to yourvehicle or you may be able to program them yourself. See the Security chapter for information on programming your transmitt...

PRINCIPLES OF OPERATION MyKey allows you to program keys with restricted driving modes topromote good driving habits. You can use all but one of the keysprogrammed to your vehicle with these restricted modes. Any keys that have not been programmed are referred to asadministrator keys or admin keys. ...

• Audio system maximum volume of 45%. A message will be shown inthe display when you attempt to exceed the limited volume. Also, thespeed-sensitive or compensated automatic volume control will bedisabled. • Always on setting. When this is selected, you will not be able to turnoff AdvanceTrac (if you...

USING MYKEY WITH REMOTE START SYSTEMS MyKey is not compatible with non-Ford-approved aftermarket remotestart systems. If you choose to install a remote start system, please seeyour Ford authorized dealer for a Ford-approved remote start system . Vehicles With Ford-approved Aftermarket Remote Start S...

Vehicles With Non-Ford-approved Aftermarket Remote StartSystems MyKey is not compatible with non-Ford-approved aftermarket remotestart systems. If you choose to install a remote start system, please see aFord authorized dealer for a Ford-approved system. The following information may help customers ...

Condition Potential causes I accidentallyprogrammed all keysas MyKeys. • The vehicle has a remote start system that is recognized as an admin key. Clear allMyKeys by using remote start. See Using MyKey With Remote Start Systems . • Your vehicle’s system does not recognize any MyKeys. See Creating a ...

LOCKING AND UNLOCKING You can use the power door lock control or the remote control to lockand unlock your vehicle. Power Door Locks The power door lock control is located on the driver and front passengerdoor panels. A. Unlock B. Lock Remote Control You can use the remote control anytime your vehic...

Power Liftgate or Liftgate Window (If Equipped) WARNING: Make sure all persons are clear of the power liftgate area before using the control. WARNING: Make sure to close and latch the liftgate to prevent drawing exhaust fumes into your vehicle. This will also prevent passengers and cargo from fallin...

Autolock and Unlock The autolock feature will lock all the doors, the liftgate and the liftgatewindow when: • all doors are closed, • the ignition is on, • you shift into any gear putting the vehicle in motion, and • the vehicle attains a speed greater than 12 mph (20 km/h). If the vehicle was autol...

Opening and Closing the Power Liftgate Note: The liftgate can be reversed with a second press on a control button or transmitter and can be manually closed at any time. The liftgate will only operate with your vehicle in P . The chime will beep once if conditions are not correct to start an operatio...

To close with the rear cargo area button: WARNING: Keep clear of the liftgate when activating the rear switch. Note: The rear cargo area control button is disabled when the liftgate is latched. Press and release the control on theleft rear quarter panel. A chime willbeep once if conditions are notco...

Resetting the Power Liftgate If any of these conditions occur, the power liftgate may not operate andmust be reset: • A low voltage or dead battery • Disconnected battery • The liftgate is manually closed and left ajar (unlatched) To reset the power liftgate: 1. Disconnect the battery for 20 seconds...

SECURICODE™ KEYLESS ENTRY KEYPAD You can use the keyless entrykeypad to lock or unlock the doorsor release the liftgate glass withoutusing a key. The keypad can be operated with the factory-set 5-digit entry code; thiscode is located on the owner’s wallet card in the glove box and isavailable from y...

Automatic Disarming Your vehicle disarms when you switch the ignition on with a coded key. Replacement Keys Note: Your vehicle may come with two integrated keyhead transmitters. The integrated keyhead transmitter functions as a programmed ignitionkey that operates all the locks and starts the vehicl...

6. Turn the ignition off and remove the second previously programmedcoded key from the ignition. 7. After three seconds but within 20 seconds of turning the ignition offand removing the previously programmed coded key, insert the newunprogrammed key into the ignition. 8. Turn the ignition from off t...

Disarming the Alarm To disarm the alarm, do any of the following: • Press the power door unlock button within the 20-second pre-armedmode. • Press the unlock button on the remote control. • Unlock the doors with the keyless entry pad. • Turn the ignition on with a valid key. • Press the panic button...

ADJUSTING THE STEERING WHEEL WARNING: Do not adjust the steering wheel when your vehicle is moving. 1. Pull and hold the steering wheelrelease lever. 2. Adjust the steering wheel to thedesired position then release thelever. AUDIO CONTROL A. Media B. Volume up C. Volume down D. Seek down or previous...

VOICE CONTROL (IF EQUIPPED) A. Voice recognition B. Phone mode Press OK to confirm selection. See the SYNC or Navigation System chapter. CRUISE CONTROL See the Cruise Control chapter. B A + SET RES OFF ON Steering Wheel 83 2014 Expedition (exd) Owners Guide gf, 1st Printing, June 2013USA (fus)

ADJUSTABLE PEDALS (IF EQUIPPED) WARNING: Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving. The control is located to the left of the steering column. Press and holdthe appropriate control to move the pedals. A. Closer B. Farther The pedal positions are...

WINDSHIELD WIPERS Note: Fully defrost the windshield before turning on the windshield wipers. Note: Make sure the windshield wipers are turned off before entering a car wash. Note: Clean the windshield and wiper blades if they begin to leave streaks or smears. If that does not resolve the issue, ins...

LIGHTING CONTROL Rotate the control clockwise to thefirst position to turn on the parkinglamps. Rotate the control clockwise to thesecond position to turn on theheadlamps. Rotate the control to the verticalposition to turn the headlamps off. High Beams • Push the lever toward theinstrument panel to ...

AUTOLAMPS The autolamp system provides lightsensitive automatic on/off controlof the exterior lights normallycontrolled by the headlamp control. The autolamp system also keepsthe lights on for approximately20 seconds or, if equipped with amessage center, you can select adelay from 0–180 seconds afte...

DAYTIME RUNNING LAMPS (IF EQUIPPED) WARNING: Always remember to switch your headlamps on in low light situations or during inclement weather. The system does not activate the tail lamps and may not provide adequate lightingduring these conditions. Failure to activate your headlamps under thesecondit...

INTERIOR LAMPS Front Row Map Lamps (If Equipped) To turn on the map lamps, press theouter edge of the clear lens. Thefront row map lamp lights when: • any door is opened. • the instrument panel dimmerswitch is rotated until the courtesylamps come on. • the remote entry controls are pressed and the i...

Rear Cargo Lamp The rear cargo lamp lights when: • any door is opened, and theswitch is in the middle position. • the instrument panel dimmerswitch is rotated until thecourtesy lamps come on. • any of the remote entry controlsare pressed and ignition is off(and switch is in the middleposition). With...

POWER WINDOWS WARNING: Do not leave children unattended in your vehicle and do not let them play with the power windows. They may seriously injure themselves. WARNING: When closing the power windows, you should verify they are free of obstructions and make sure that children and pets are not in the ...

Window Lock A. Unlock B. Lock Press the control to lock or unlock the rear and front passenger windowcontrols. Accessory Delay You can use the window switches for several minutes after you switchthe ignition off, or until you open either front door. EXTERIOR MIRRORS Power Exterior Mirrors WARNING: D...

Power-Folding Mirrors (If Equipped) Note: Using the mirrors 10 or more times within one minute, or repeated folding and unfolding of the mirrors while holding the controldown during full travel, may disable the system to protect motors fromoverheating. Wait approximately three minutes with your vehi...

Integrated Blind Spot Mirrors WARNING: Objects in the blind spot mirror are closer than they appear. Blind spot mirrors have an integrated convex mirror built into the upperoutboard corner of the exterior mirrors. They are designed to assist youby increasing visibility along the side of your vehicle...

INTERIOR MIRROR WARNING: Do not adjust the mirror when your vehicle is moving. Note: Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum or ammonia based cleaning products. You can adjust the interior mirror to your preference. Some mirrors alsohave a second...

GAUGES Cluster shown in standard measure. Metric similar. A. Tachometer B. Battery voltage gauge: C. Engine oil pressure gauge D. Speedometer E. Fuel gauge F. Information display. See Information displays for more information. G. Engine coolant temperature gauge Battery Voltage Gauge Indicates the b...

Engine Oil Pressure Gauge Indicates engine oil pressure. The needle should stay in the normaloperating range. If the needle falls below the normal range, stop thevehicle, turn off the engine and check the engine oil level. Add oil ifneeded. If the oil level is correct, have your vehicle checked at y...

WARNING LAMPS AND INDICATORS The following warning lamps and indicators will alert you to a vehiclecondition that may become serious. Some lamps will illuminate when youstart your vehicle to make sure they work. If any lamps remain on afterstarting your vehicle, refer to the respective system warnin...

High Beam It will illuminate when the headlamp high beam is switched on. It will flash when you use the headlamp flasher. Low Fuel Level It will illuminate when the fuel level is low or near empty.Refuel as soon as possible. Low Tire Pressure Warning It will illuminate when your tire pressure is low...

Service Engine Soon The service engine soon indicator light illuminates when the ignition is first turned to the on position to check the bulb and toindicate whether the vehicle is ready for Inspection/Maintenance (I/M) testing. Normally, the “service engine soon” light will stay on until theengine ...

4X4 Illuminates when four-wheel drive high is engaged. If the light failsto display when the ignition is turned on, or remains on, have thesystem serviced immediately by your authorized dealer. 4X4 LOW Illuminates when four-wheel drive low is engaged. If the light failsto display when the ignition i...

GENERAL INFORMATION WARNING: Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus offthe road. Your primary responsibility is the safe operation of yourvehicle. We recommend...

• MILES (km) TO E: This displays an estimate of approximately how faryou can drive with the fuel remaining in your tank under normaldriving conditions. Remember to turn the ignition off when refuelingto allow this feature to correctly detect the added fuel. Distance toempty is calculated using a run...

Compass calibration adjustment Note: For optimum calibration, drive to an open, level location away from large metallic objects or structures. Switch off all non-essentialelectrical accessories (heated rear window, heater, A/C, map lamps,wiper, etc.) and make sure all the doors are closed Note: If t...

Press and hold the SELECT/RESET stem to get into the setup menusequence for the following displays: SETUP HOLD RESETFOR SYSTEMCHECK press and holdtheSELECT/RESETstem OIL LIFE CHARGING SYSTEM WASHER FLUID LEVEL DOOR AJAR STATUS LIFTGATE/GLASS AJAR STATUS BRAKE SYSTEM MYKEY DISTANCE(if programmed) X M...

Information Display Controls (Type 2) • Press the INFO button to scrollthrough trip, fuel usage, andMyKey® information. • Press the SETUP button to scrollthrough various vehicle featuresettings. • Press the RESET button to choose settings, reset information andconfirm messages. Info Press the INFO b...

Maintenance Messages Action / Description ENGINE OILCHANGE SOON Displayed when the engine oil life is nearingits end. OIL CHANGEREQUIRED Displayed when the oil life left reaches 0%. WASHER FLUIDLEVEL LOW Indicates the washer fluid reservoir is less thanone quarter full. Check the washer fluid level....

4WD Messages Action / Description TO EXIT 4X4 LOWSHIFT TO N Displayed when 2WD is selected while thevehicle has been stopped in 4X4 LOW. TO EXIT 4X4 LOWSLOW TO 3 MPH Displayed when 2WD is selected while thevehicle is operating in 4X4 LOW. SHIFT DELAYEDPULL FORWARD May display when shifting to or fro...

MANUAL HEATING AND AIR CONDITIONING SYSTEM WITHOUTAUXILIARY CLIMATE CONTROL A. Fan speed control: Controls the volume of air circulated in your vehicle. Turn to select the desired fan speed or switch off. If you switchthe fan off, the windshield may fog up. B. Temperature control: Controls the tempe...

Distributes air through the floor vents. Distributes air through the windshield defroster vents, demistervents and floor vents. Distributes air through the windshield defroster vents anddemister vents. This setting can also be used to defog and clearthe windshield of a thin covering of ice. D. Auxil...

When this button is pressed, the display only shows the rear temperaturesetting. After the rear setting changes are completed on the frontcontrol, the display automatically shows both climate settings. F. Passenger temperature control: Press and turn to increase or decrease the air temperature on th...

F. REAR (temperature control): Press to turn on the auxiliary climate control system and to set the desired rear temperature with the frontcontrol. The rear temperature is the same as the front temperature whenonly the center rear temperature bar is lit. The rear temperature isdifferent from the fro...

Distributes air through the floor vents. Distributes air through the windshield defroster vents, demistervents and floor vents. N. Driver heated seat control: Press to switch the driver heated seat off and on. See Heated seats in the Seats chapter for more information. O. Driver cooled seat control:...

GENERAL OPERATING TIPS Manual Heating and Air Conditioning System • To reduce fog build-up on the windshield during humid weather,select Defrost. Temperature and fan speed can also be increased toimprove clearing. • To reduce humidity build-up inside the vehicle, do not drive with thesystem off or w...

Dual Automatic Temperature Control System • To reduce fog build-up on the windshield during humid weather,select Defrost. Temperature and fan speed can also be increased toimprove clearing. • To reduce humidity build-up inside the vehicle, do not drive with thesystem off or with recirculated air eng...

HEATED WINDOWS AND MIRRORS (IF EQUIPPED) Heated Rear Window Note: The vehicle must be running to use this feature. Press the control to clear the rear window of thin ice and fog. Press thecontrol again within 15 minutes to switch it off. It turns off automaticallyafter approximately 15 minutes, or w...

SITTING IN THE CORRECT POSITION WARNING: Sitting improperly out of position or with the seatback reclined too far can take off weight from the seat cushion and affect the passenger sensing system, resulting in seriousinjury or death in a crash. Always sit upright against your seatback,with your feet...

Adjusting the Head Restraint Raise: Pull up the head restraint. Lower: 1. Press and hold button C. 2. Push down on the head restraint. Remove: 1. Pull up the head restraint until it reaches the highest adjustmentposition. 2. Press and hold buttons C and D. 3. Pull up the head restraint. Reinstall Al...

Power Lumbar (If Equipped) The control is located on theoutboard side of the seat. Press theforward or rearward side of thecontrol for more or less support. MEMORY FUNCTION (IF EQUIPPED) This feature will save and recall the positions of the driver seat, powermirrors and adjustable pedals. The memor...

Heated and Ventilated Seats Air Filter Replacement (If Equipped) The heated and ventilated seat system includes air filters. You mustreplace them periodically. See scheduled maintenance information for more information. There is a filter located under each front seat. You can access the filterfrom t...

REAR SEATS Folding Down the 2nd Row 40% Seat System WARNING: Use caution when folding the seat back to the flat back position as the system will move forward when you lift the release handle. WARNING: Before returning the seat back to its original position, make sure that cargo or any objects are no...

2. Locate handle on the side of theseat cushion by the door. 3. Pull up on the handle and pushthe seat back forward toward thefront of the vehicle. To return the seat to the upright position: 1. Lift the seat back toward the rearof the vehicle. 2. Rotate the seat back until youhear a click, locking ...

Placing the Second Row Outboard 40% Seats in Cargo Mode WARNING: Use caution when folding the seatback to the flat back position as the system will move forward when you lift the release handle. WARNING: Always return the seat from the kneel position prior to raising the seatback. Failure to do so c...

Returning to the upright position from full lowered load floorposition You cannot return the seatback to the upright position until the seat isreturned from the kneel down position. To return the seat to the uprightposition: 1. Push the seat rearward until thelatch is engaged. 2. Return the seatback...

The heated seats only operate when the ignition is on. To operate theheated seats: Press the heated seat button to cycle through the variousheat settings and off. Warmer settings are indicated bymore indicator lights. Third Row Seats Make sure that no objects are on the floor in front of the third r...

UNIVERSAL GARAGE DOOR OPENER The appearance of your vehicle’s universal garage door opener will varyaccording to your option package. Before programing, make sure youidentify which transmitter you have by comparing it to the graphicsbelow. HomeLink® Car2U® Home AutomationSystem Note: The programming...

Rolling Code Programming Note: If you do not follow the time-sensitive instructions, the device will time out and you will have to repeat the complete procedure. Note: It may be helpful to have another person assist you in programming the transmitter. 1. Switch the ignition on. 2. Press and hold the...

8. The LED lamp will begin to flash rapidly until programming iscomplete. If your garage door does not operate, repeat the previoussteps. Otherwise, call the toll-free help line at 1-866-572-2728. The LED lamp above the selected button will illuminate to confirm thatthe system is responding to the b...

Erasing the Function Button Codes Note: You cannot erase individual buttons. 1. Press and hold the outer two functionbuttons simultaneously for approximately20 seconds until the indicator lights abovethe buttons flash rapidly. 2. When the indicator lights flash, releasethe buttons. The codes for all...

AUXILIARY POWER POINTS WARNING: Do not plug optional electrical accessories into the cigarette lighter socket (if equipped). Improper use of the lighter can cause damage not covered by your warranty, and can result in fireor serious injury. Note: If used when the engine is not running, the battery w...

CENTER CONSOLE (IF EQUIPPED) Stow items in the cupholder carefully as items may become loose duringhard braking, acceleration or collisions, including hot drinks which mayspill. Available console features include: A. Cupholders B. Utility compartment, coin holderslots, tissue box holder, audio input...

GENERAL INFORMATION WARNING: Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system, creating the risk of fire or other damage. WARNING: Do not park, idle, or drive your vehicle on dry grass or other dry ground cover. The emission system heats up th...

The heater acts as a starting aid by warming the engine coolant. Thisallows the climate control system to respond quickly. The equipmentincludes a heater element (installed in the engine block) and a wireharness. You can connect the system to a grounded 120–volt A/Celectrical source. We recommend th...

SAFETY PRECAUTIONS WARNING: Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. WARNING: The fuel system may be under pressure. If you hear a hissing sound near the fuel filler inlet, do not refuel until the sound stops. Otherwise, fue...

• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes,remove contact lenses (if worn), flush with water for 15 minutes andseek medical attention. Failure to seek proper medical attention couldlead to permanent injury. • Fuels can also be harmful if absorbed through the skin. If f...

Choosing the Right Fuel With a Flex Fuel Vehicle (If Equipped) Use only UNLEADED gasoline or UNLEADED gasoline blended with amaximum of 85% ethanol (E-85) in your Flex Fuel Vehicle (FFV). Ifyour vehicle is flex fuel capable, it will have a yellow bezel placed overthe fuel fill inlet. Do not use: • f...

RUNNING OUT OF FUEL Avoid running out of fuel because this situation may have an adverseeffect on powertrain components. If you have run out of fuel: • You may need to cycle the ignition from off to on several times afterrefueling to allow the fuel system to pump the fuel from the tank tothe engine....

1. The white plastic funnel is located under thespare tire tool panel located in the floorcompartment behind the rear seat. 2. Unlatch and remove the spare tire tool panel. Remove the whiteplastic funnel. 3. Slowly insert the funnel into the Easy Fuel system. 4. Fill the vehicle with fuel from the p...

Easy Fuel® “No Cap” Fuel System WARNING: The fuel system may be under pressure. If you hear a hissing sound near the fuel filler door, do not refuel until the sound stops. Otherwise, fuel may spray out, which could cause seriouspersonal injury. When fueling your vehicle: 1. Turn the engine off. 2. O...

EMISSION CONTROL SYSTEM WARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. WARNING: Exhaust leaks may result in entry of harmful and potentially lethal fumes into th...

AUTOMATIC TRANSMISSION WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the off position and remove the key whenever you leave your vehicle. WARNING: Do not use the Tow/Haul feature when driving in icy or slippery conditions as the ...

Brake-Shift Interlock – Floor-Shift Transmission WARNING: Do not drive your vehicle until you verify that the brake lamps are working. WARNING: When doing this procedure, you will be taking the vehicle out of park which means the vehicle can roll freely. To avoid unwanted vehicle movement, always fu...

If the fuse is not blown, perform the following procedure: 1. Apply the parking brake. 2. Turn the key to the off position. 3. Remove the access plug on top ofthe steering column. 4. Using a flat-head screwdriver orsimilar tool, move the brake-shiftinterlock actuator spindle towardthe left, apply th...

USING FOUR-WHEEL DRIVE (4WD) (IF EQUIPPED ) WARNING: For important information regarding safe operation of this type of vehicle, see General Information in the Wheels and Tires chapter. Note: Do not use 4X4 mode on dry, hard surfaced roads. Doing so will produce excessive noise, increase tire wear a...

4WD switch positions WARNING: Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorilyunder off-road conditions. Avoid sharp turns or abrupt maneuvers inthese vehicles. Note: If...

• 4L (4X4 LOW) provides electronically locked four-wheel drive when extra power at reduced speeds is required. The message center willdisplay 4X4 LOW when this mode is selected. This mode is notrecommended for use on dry pavement. Use this mode for off-roadlow-speed operation or when extra power is ...

How Your Vehicle Differs From Other Vehicles WARNING: Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drivevehicles are not designed for cornering at speeds as high as passe...

Maintenance and modifications The suspension and steering systems on your vehicle have been designedand tested to provide predictable performance whether loaded or emptyand durable load carrying capability. For this reason, Ford MotorCompany strongly recommends that you do not make modifications suc...

GENERAL INFORMATION Note: Occasional brake noise is normal. If a metal-to-metal, continuous grinding or continuous squeal sound is present, the brake linings may beworn out. Have them inspected by an authorized dealer. If your vehiclehas continuous vibration or shudder in the steering wheel while br...

PRINCIPLES OF OPERATION The traction control system helps avoid drive wheel spin and loss oftraction. If your vehicle begins to slide, the system applies the brakes to individualwheels and, when needed, reduces engine power at the same time. If thewheels spin when accelerating on slippery or loose s...

PRINCIPLES OF OPERATION WARNING: Vehicle modifications involving braking system, aftermarket roof racks, suspension, steering system, tire construction or wheel and tire size may change the handlingcharacteristics of the vehicle and may adversely affect the performanceof the AdvanceTrac® system. In ...

A Vehicle without AdvanceTrac® with RSC® skidding off its intendedroute. B Vehicle with AdvanceTrac® with RSC® maintaining control on aslippery surface. USING ADVANCETRAC® WITH RSC® The system automatically activates when you start your engine. TheAdvanceTrac® with RSC® system cannot be completely t...

SENSING SYSTEM (IF EQUIPPED) WARNING: To help avoid personal injury, please read and understand the limitations of the system as contained in this section. Sensing is only an aid for some (generally large and fixed)objects when moving in reverse on a flat surface at parking speeds.Traffic control sy...

Using the Front and Rear Sensing System Rear Sensing System The rear sensors are only active when the transmission is in R (Reverse).As the vehicle moves closer to the obstacle, the rate of the audiblewarning increases. When the obstacle is fewer than 10 inches(25 centimeters) away, the warning soun...

Front Sensing System The front sensors are active when the gearshift is in any position otherthan P (Park) or N (Neutral) and the vehicle speed is below 8 mph(13 km/h). A. Coverage area of up to 27 inches(70 centimeters) from the front ofthe vehicle and about 6–9 inches(15–23 centimeters) to the sid...

Using the Rear View Camera System The rear view camera system displays what is behind your vehicle whenyou place the transmission in R (Reverse). The system uses two types ofguides to help you see what is behind your vehicle:1. Fixed guidelines: Show the actual path the vehicle is moving in while re...

Guidelines and the Centerline Note: Fixed guidelines are only available when the transmission is in R (Reverse). Note: The centerline is only available if fixed guidelines are on. A. Rear bumper B. Fixed guideline: Red zone C. Fixed guideline: Yellow zone D. Fixed guideline: Green zone E. Centerline...

PRINCIPLES OF OPERATION Cruise control lets you maintain a set speed without keeping your footon the accelerator pedal. USING CRUISE CONTROL WARNING: Do not use cruise control in heavy traffic, on winding roads or when the road surface is slippery. This could result in loss of vehicle control, serio...

STEERING Your vehicle is equipped with power steering. Power steering uses energyfrom the engine to decrease the driver’s effort in steering the vehicle. To help prevent damage to the power steering pump: • Never hold the steering wheel to the extreme right or the extreme leftfor more than a few sec...

AUTO LEVELING SUSPENSION SYSTEM (if equipped) The automatic leveling suspension system is designed to improve ride,handling and general vehicle performance during: • Certain road conditions • Steering maneuvers • Braking • Acceleration • Towing This system keeps the rear of your vehicle at a constan...

ROOF RACKS AND LOAD CARRIERS WARNING: When loading the roof rail crossbars, it is recommended to evenly distribute the load, as well as maintain a low center of gravity. Loaded vehicles, with higher centers of gravity,may handle differently than unloaded vehicles. Extra precautions, suchas slower sp...

LOAD LIMIT Vehicle Loading – With and Without a Trailer This section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehicle weight within its design ratingcapability, with or without a trailer. Properly loading your vehicle willprovide maximum return of vehic...

Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weigh...

• Example only: WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structuraldamage, serious damage to the vehicle, loss of control and personalinjury. Load Carrying 219 20...

GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo andpassengers – that the vehicle can handle without r...

WARNING: Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tires with ahigher limit than the original tires do not increase the GVWR andGAWR limitations. WARNING: Exceeding any vehicle ...

To move the shelf to the dividerposition: Pull up and pivot the shelf over the channels on the sidetrim panels and snap vertically inplace. POWER DEPLOYABLE RUNNING BOARDS (IF EQUIPPED) WARNING: In extreme climates, excessive ice buildup may occur, causing the running boards not to deploy. Be sure t...

The running boards automaticallymove when the doors are opened toassist entering and exiting thevehicle. Automatic Power Deploy The running boards will extend down and out when the doors areopened. Automatic Power Stow The running boards will return to the stowed position after a two seconddelay whe...

TOWING A TRAILER WARNING: Do not exceed the GVWR or the GAWR specified on the certification label. WARNING: Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of your vehicle and could result in engine damage, transmission damage, structural damage, lossof vehicle ...

TRAILER SWAY CONTROL WARNING: Turning off trailer sway control increases the risk of loss of vehicle control, serious injury or death. Ford does not recommend disabling this feature except in situations where speedreduction may be detrimental (such as hill climbing), the driver hassignificant traile...

Vehicle type Towing package Maximum GCWR Two–wheel drive(except EL and Max)Two–wheel drive EL(U.S.)Two–wheel drive Max(Canada)Four–wheel drive(except EL and Max)Four–wheel drive EL(U.S.)Four–wheel drive Max(Canada) Optional 15000 lb (6804 kg) ESSENTIAL TOWING CHECKS Follow these guidelines for safe ...

Trailer Towing Connector (Vehicles with a Trailer Towing Packageand 7–Pin Connector) When attaching the trailer wiringconnector to your vehicle, only usea proper fitting connector thatworks with the vehicle and trailerfunctions. If your vehicle has atrailer towing package, it may havea 7–pin connect...

The standard integrated hitch has two ratings depending on mode ofoperation: • Weight-carrying mode requires a draw bar and hitch ball. The drawbar supports all the vertical tongue load of the trailer. • Weight-distributing mode requires an aftermarket weight-distributingsystem, which includes draw ...

Integrated Trailer Brake Controller (If Equipped) WARNING: The Ford TBC has been verified to be compatible with trailers having electric-actuated drum brakes (one to four axles) and some electric-over-hydraulic (EOH) brakes. It will notactivate hydraulic surge-style trailer brakes. It is the respons...

The controller shows gain setting, output bar graph, and trailerconnectivity status in the information display. They appear in theinformation display as follows: • TBC GAIN = XX.X NO TRAILER: Shows the current gain setting during a given ignition cycle and when adjusting the gain. This alsodisplays ...

The gain should be set to provide the maximum trailer braking assistancewhile making sure the trailer wheels do not lock when using the brakes.Locked trailer wheels may lead to trailer instability.1. Make sure the trailer brakes are in good working condition, functioning normally and properly adjust...

Trailer Lamps WARNING: Never connect any trailer lamp wiring to the vehicle’s tail lamp wiring; this may damage the electrical system resulting in a fire. Contact an authorized dealer as soon as possible forassistance in proper trailer tow wiring installation. Additional electricalequipment may be r...

• If you are towing a trailer frequently in hot weather, hilly conditions,at the gross combined weight rating (or any combination of thesefactors), consider refilling your rear axle with synthetic gear lubricant(if the axle is not already filled with it). See the Capacities and Specifications chapte...

TRANSPORTING THE VEHICLE If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. We recommend the use of a wheel lift and dollies or flatbed equipmentto tow your vehicle. Do not t...

TOWING THE VEHICLE ON FOUR WHEELS Emergency Towing If your vehicle becomes inoperable (without access to wheel dollies,car-hauling trailer, or flatbed transport vehicle), it can be flat-towed (allwheels on the ground, regardless of the powertrain and transmissionconfiguration) under the following co...

BREAKING-IN You need to break in new tires for approximately 300 miles(480 kilometers). During this time, your vehicle may exhibit some uniquedriving characteristics. Avoid driving too fast during the first 1000 miles(1600 kilometers). Vary your speed frequently and change up throughthe gears early....

• Carry unnecessary weight (approximately 1 mpg [0.4 km/L] is lost forevery 400 pounds [180 kilograms] of weight carried). • Add particular accessories to your vehicle (e.g.; bug deflectors,rollbars or light bars, running boards, ski racks). • Drive with the wheels out of alignment. DRIVING THROUGH ...

FLOOR MATS WARNING: Always use floor mats that are designed to fit the footwell of your vehicle. Only use floor mats that leave the pedal area unobstructed. Only use floor mats that are firmly secured toretention posts so that they cannot slip out of position and interferewith the pedals or impair s...

WARNING (Continued) • Failure to properly follow floor mat installation or attachmentinstructions can potentially cause interference with pedal operationcausing loss of control of vehicle. • To install floor mats, position the floor mat so that the eyelet is overthe retention post and press down to ...

ROADSIDE ASSISTANCE Vehicles Sold in the U.S.: Getting Roadside Assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24 hours a...

Vehicles Sold in the U.S.: Using Roadside Assistance Complete the roadside assistance identification card and place it in yourwallet for quick reference. This card is found in the owner’s manualportfolio in the glove compartment. U.S. Ford vehicle customers who require Roadside Assistance, call1-800...

FUEL PUMP SHUT-OFF SWITCH The fuel pump shut-off switch is a device intended to stop the electricfuel pump when your vehicle has been involved in a substantial jolt. After a collision, if the engine cranks but does not start, the fuel pumpshut-off switch may have been activated. The fuel pump shut-o...

Connecting the Jumper Cables WARNING: Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery. Note: Do not attach the negative (-) cable to fuel lines, engine rocker covers, the intake...

Removing the Jumper Cables Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery. Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable fromthe ground metal surface. 2. Remove the jumper cable on thenega...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizeddealer. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfaction. Plea...

• Ford Genuine Accessories • Service specials and promotions. In Canada: Mailing address Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6K 1C8 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Additional Assistance If you have questions or concerns,...

UTILIZING THE MEDIATION or ARBITRATION PROGRAM(CANADA ONLY) This pertains to vehicles delivered to authorized Canadian dealers.In those cases, where you continue to feel that the efforts by Ford ofCanada and the authorized dealer to resolve a factory-related vehicleservice concern have been unsatisf...

CHANGING A FUSE Fuses WARNING: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. If electrical components in yourvehicle are not working, a fuse mayhave blown. Blown fuses are identif...

FUSE SPECIFICATION CHART Power Distribution Box WARNING: Always disconnect the battery before servicing high current fuses. WARNING: To reduce risk of electrical shock, always replace the cover to the power distribution box before reconnecting the battery or refilling fluid reservoirs. The power dis...

Fuse or relay location Fuse amp rating Protected circuits 82 — Not used 83 — Not used 84 — Not used 85 — Wiper motor relay * Mini Fuses ** Cartridge Fuses Passenger Compartment Fuse Panel The fuse panel is located under the right-hand side of the instrumentpanel. To remove the trim panel for accesst...

GENERAL INFORMATION WARNING: Turn off the power running boards, if equipped, before working under the vehicle, jacking or placing any object under the vehicle. Never place your hand between the extendedrunning board and the vehicle. A moving running board may causeinjury. Have your vehicle serviced ...

Working with the Engine Off 1. Set the parking brake and shift to P (Park). 2. Turn off the engine and remove the key (if equipped). 3. Block the wheels. Working with the Engine On WARNING: To reduce the risk of vehicle damage or personal burn injuries, do not start your engine with the air cleaner ...

UNDER HOOD OVERVIEW 5.4L V8 A. Windshield washer fluid reservoir B. Engine oil dipstick C. Brake fluid reservoir D. Engine coolant reservoir E. Air filter assembly F. Power steering fluid reservoir G. Power distribution box H. Engine oil filler cap I. Battery A B C D E F G H I Maintenance 271 2014 E...

Adding Engine Oil Note: Do not remove the engine oil level dipstick or the filler cap when the engine is running. Note: Do not add engine oil further than the MAX mark. Oil levels above the MAX mark may cause engine damage. Only use oils certified for gasoline engines by theAmerican Petroleum Instit...

Note: For best results, coolant concentration should be tested with a refractometer such as Rotunda tool 300-ROB75240 available from yourdealer. Ford does not recommend the use of hydrometers or coolant teststrips for measuring coolant concentrations. Note: Automotive fluids are not interchangeable;...

• In case of emergency, a large amount of water without engine coolantmay be added in order to reach a vehicle service location. In thisinstance, the cooling system must be drained, chemically cleaned withMotorcraft Premium Cooling System Flush, and refilled with enginecoolant as soon as possible. W...

If you drive in extremely hot climates: • It may be necessary to have a Ford authorized dealer decrease thecoolant concentration to 40%. • A coolant concentration of 40% will provide improved overheatprotection. Engine coolant concentrations below 40% will decrease thecorrosion/freeze protection cha...

When Fail-Safe Mode is Activated WARNING: Fail-safe mode is for use during emergencies only. Operate the vehicle in fail-safe mode only as long as necessary to bring the vehicle to rest in a safe location and seek immediate repairs.When in fail-safe mode, the vehicle will have limited power, will no...

AUTOMATIC TRANSMISSION FLUID CHECK Note: Transmission fluid should be checked by an authorized dealer. If required, fluid should be added by an authorized dealer. The automatic transmission does not have a transmission fluid dipstick. Refer to your scheduled maintenance information for scheduled int...

FUEL FILTER Your vehicle is equipped with a lifetime fuel filter that is integrated withthe fuel tank. Regular maintenance or replacement is not needed. WASHER FLUID CHECK WARNING: If you operate your vehicle in temperatures below 40°F (5°C), use washer fluid with antifreeze protection. Failure to u...

Because your vehicle’s engine is electronically controlled by a computer,some control conditions are maintained by power from the battery. Whenthe battery is disconnected or a new battery is installed, the engine mustrelearn its idle and fuel trim strategy for optimum driveability andperformance. To...

CHANGING THE WIPER BLADES Replace wiper blades at least once per year for optimum performance. To replace the wiper blades: 1. Fold back the wiper arm andposition the wiper blade at a rightangle to the wiper arm. 2. To remove the wiper blade, pressthe retaining clip (A) to disengagethe wiper blade, ...

4. To attach the new wiper to thewiper arm, align the cross pin andkeyway (denoted with the arrows)and firmly press the wiper bladeinto the wiper arm until an audiblesnap is heard. If you find this procedure too difficult, please see your dealer. AIR FILTER CHECK WARNING: To reduce the risk of vehic...

Changing the Air Filter Element 1. Locate the mass air flow sensorelectrical connector on the airoutlet tube. This connector willneed to be unplugged. 2. Unlock the locking clip on theconnector (connector shown frombelow for clarity), then squeeze andpull the connector off of the airoutlet tube. 3. ...

5. Locate the vertical adjuster oneach headlamp, then use a Phillips#2 screwdriver to turn the adjustereither counterclockwise orclockwise in order to adjust thevertical aim of the headlamp. Theupper edge of the light patternshould line up to the horizontal line. 6. Repeat Steps 3–5 for the otherhea...

Replacing Headlamp Bulbs WARNING: Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause thebulb to break the next time the headlamps are operated. 1. Make sure that the headlam...

Replacing Tail, Stop, Turn Signal, Side Marker, and Backup LampBulbs The tail, stop, turn signal, side marker, and backup lamp bulbs arelocated in the same portion of the tail lamp assembly, one just below theother. Follow the same steps to replace any bulb: 1. Make sure the headlamp switch isin the...

Replacing License Plate Lamp Bulbs The license plate bulbs are located in the license plate housing assemblyon the liftgate. To change the license plate bulbs: 1. Make sure the headlamp switch isin the off position. 2. Remove the license lamp screwfrom the assembly. 3. Pull the lamp down and twist t...

• Spray Motorcraft® Engine Shampoo and Degreaser on all parts thatrequire cleaning and pressure rinse clean. In Canada, use Motorcraft®Engine Shampoo. • Never wash or rinse the engine while it is hot or running; water in therunning engine may cause internal damage. • Never wash or rinse any ignition...

CLEANING THE INTERIOR WARNING: Do not use cleaning solvents, bleach or dye on the vehicle’s safety belts, as these actions may weaken the belt webbing. WARNING: On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents. Such products could contaminate the side...

CLEANING LEATHER SEATS(IF EQUIPPED, EXCEPT FOR THE KING RANCH® EDITION) Note: For the King Ranch® Edition leather seats, refer to a separate section in this chapter. • Clean spills and stains as quickly as possible. • For routine cleaning, wipe the surface with a soft, damp cloth. Formore thorough c...

Scratches Natural Markings - Because the leather in the seat comes from genuinesteer hides, there will be evidence of naturally occurring markings, suchas small scars. These markings give character to the seating covers andshould be considered as proof of a genuine leather product. In order to lesse...

• Do not use hydrofluoric acid-based or high caustic-based wheelcleaners, steel wool, fuels or strong household detergent. • If you intend on parking your vehicle for an extended period aftercleaning the wheels with a wheel cleaner, drive your vehicle for a fewminutes before doing so. This reduces t...

Removing Vehicle from Storage When your vehicle is ready to come out of storage, do the following: • Wash your vehicle to remove any dirt or grease film build-up onwindow surfaces. • Check windshield wipers for any deterioration. • Check under the hood for any foreign material that may have collecte...

GENERAL INFORMATION Notice to Utility Vehicle, Van and Truck Owners WARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles. To reduce the risk of serious injury or death from a rollover or other crash you must: • Avoid sharp turns and abrupt maneuvers; • Dri...

Treadwear The treadwear grade is a comparative rating based on the wear rate of thetire when tested under controlled conditions on a specified government testcourse. For example, a tire graded 150 would wear 1 1 ⁄ 2 times as well on the government course as a tire graded 100. The relative performanc...

INFORMATION CONTAINED ON THE TIRE SIDEWALL Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. This informationidentifies and describes the fundamental characteristics of the tire and alsoprovides a U.S. DOT Tire Identifi...

E. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheeldiameter. F. 95: Indicates the tire’s load index. It is an index that relates to how much weight a tire can carry. You may find this information in yourowner...

Information on T Type Tires T type tires have some additionalinformation beyond those of P typetires. These differences aredescribed below. T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Gradesdo not apply to thi...

INFLATING YOUR TIRES Safe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air pressurewithout appearing flat. Every day before you drive, check your tires. If one looks lower than theothers, use a tire gauge to check pressure o...

Maximum Inflation Pressure is the tire manufacturer’s maximum permissible pressure or the pressure at which the maximum load can becarried by the tire. This pressure is normally higher than the manufacturer’srecommended cold inflation pressure, which can be found on the SafetyCompliance Certificatio...

(4.15 bar). For full-size and dissimilar spare tires, see Dissimilar Spare Tire and Wheel Assembly Information under Changing a Road Wheel in this chapter. Store and maintain at the higher of the front and rearinflation pressure as shown on the Tire Label. 6. Visually inspect the tires to make sure ...

Damage Periodically inspect the tire treads and sidewalls for damage (such asbulges in the tread or sidewalls, cracks in the tread groove andseparation in the tread or sidewall). If damage is observed or suspected,have the tire inspected by a tire professional. Tires can be damagedduring off-road us...

Tire Replacement Requirements WARNING: Only use replacement tires and wheels that are the same size, load index, speed rating and type (such as P-metric versus LT-metric or all-season versus all-terrain) as those originallyprovided by Ford. The recommended tire and wheel size may be foundon either t...

Safety Practices WARNING: If your vehicle is stuck in snow, mud, or sand, do not rapidly spin the tires. Spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to fiveseconds. WARNING: Do not spin the wheels at over 35 mph (56 km/h). The tires may fail ...

The tires should also be balanced periodically. An unbalanced tire andwheel assembly may result in irregular tire wear. Tire Rotation Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanicalproblem involved before tir...

USING SNOW CHAINS WARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety and performanceof your vehicle, which could result in an increased risk of loss of vehiclecontrol, vehicl...

TIRE PRESSURE MONITORING SYSTEM WARNING: The tire pressure monitoring system is NOT a substitute for manually checking tire pressure. The tire pressure should be checked periodically (at least monthly) using a tire gauge.See Inflating Your Tires in this chapter. Failure to properly maintain your tir...

telltale after replacing one or more tires or wheels on your vehicle toensure that the replacement or alternate tires and wheels allow theTPMS to continue to function properly. The tire pressure monitoring system complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is...

When you believe your system is not operating properly The main function of the tire pressure monitoring system is to warn youwhen your tires need air. It can also warn you in the event the system isno longer capable of functioning as intended. See the following chart forinformation concerning your ...

Low tirepressurewarning light Possible cause Customer action required Flashing warninglight Spare tire in use Repair the damaged road wheel andtire and reinstall it on the vehicle torestore system function. For adescription on how the systemfunctions, see When your temporary spare tire is installed ...

CHANGING A ROAD WHEEL WARNING: The use of tire sealants may damage your tire pressure monitoring system and should not be used. However, if you must use a sealant, have an authorized dealer install a new tirepressure monitoring system sensor and valve stem. WARNING: See Tire Pressure Monitoring Syst...

The usage of a full-size dissimilar spare tire and wheel assembly can leadto impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability • All-wheel driving...

Removing the jack and tools 1. Open the liftgate, then locate theaccess panel on the floor behind thethird row seat. Unlatch and removethe panel. 2. Remove the jack and toolsassembly tray from thecompartment by turning thewing-nut counterclockwise torelieve tension against the jackassembly tray. Rem...

6. Reinstall the jack bag properly around the jack and tool assembly tray,making sure the strap is securely fastened. 7. Close the access hole with the rubber plug. 8. Reinstall the tray into the vehicle and secure it with the wing nut(turn clockwise until tight). TECHNICAL SPECIFICATIONS Wheel Lug ...

VEHICLE IDENTIFICATION NUMBER The vehicle identification number islocated on the driver’s sideinstrument panel. Please note that in the graphic,XXXX is representative of yourvehicle identification number. The Vehicle Identification Number (VIN) contains the followinginformation: A. World manufacture...

ACCESSORIES For a complete listing of the accessories that are available for yourvehicle, please contact an authorized dealer or visit our online store at www.Accessories.Ford.com (United States only). Ford Motor Company will repair or replace any properly authorizeddealer-installed Ford Genuine Acc...

FORD ESP EXTENDED SERVICE PLANS PROTECT YOURSELF FROM THE RISING COST OF VEHICLE REPAIRSWITH A FORD EXTENDED SERVICE PLAN. SERVICE PLANS (U.S. only) More than 32 Million Ford and Lincoln owners have discovered thepowerful protection Ford ESP. It is the only extended service planbacked by Ford Motor ...

Interest Free Financing Options Available Take advantage of our interest free installment payment plan. Just a 10%down payment will provide you with an affordable, no interest, no feepayment program. Complete the information below and mail to: Ford ESPPO Box 8072Royal Oak Michigan 48068-0039 To lear...

GENERAL INFORMATION Radio Frequencies and Reception Factors AM and FM frequencies are established by the Federal CommunicationsCommission (FCC) and the Canadian Radio and TelecommunicationsCommission (CRTC). Those frequencies are: AM: 530, 540–1700, 1710 kHz FM: 87.9–107.7, 107.9 MHz Radio reception...

MP3 Track and Folder Structure Audio systems capable of recognizing and playing MP3 individual tracksand folder structures work as follows: • There are two different modes for MP3 disc playback: MP3 trackmode (system default) and MP3 folder mode. • MP3 track mode ignores any folder structure on the ...

AM/FM/CD WITH SYNC® WARNING: Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus offthe road. Your primary responsibility is the safe operation of yourvehicle. We recommend...

REAR AUDIO CONTROLS Your vehicle is equipped with rear seat audio controls. This allows frontand middle seat passengers to listen to different media sources (radio,CD or SYNC) simultaneously. Note: The front and middle seat passengers cannot listen to two different radio stations at the same time. A...

Switching Dual Play Mode On You can switch Dual Play mode on by simultaneously pressing the 2 and4 memory preset buttons on the audio or by doing the following:1. Press the headphone/speaker control. The headphone icon illuminates in both front and rear audio displays indicating the rearseat speaker...

SATELLITE RADIO INFORMATION (IF EQUIPPED) Satellite Radio Channels Sirius broadcasts a variety of music, news, sports, weather, traffic andentertainment satellite radio channels. For more information and acomplete list of Sirius satellite radio channels, visit www.siriusxm.com inthe United States, w...

Sirius Satellite Radio Service Note: Sirius reserves the unrestricted right to change, rearrange, add or delete programming including canceling, moving or adding particularchannels, and its prices, at any time, with or without notice to you. FordMotor Company shall not be responsible for any such pr...

Troubleshooting Radio display Condition Possible action Acquiring Radio requires more thantwo seconds to produceaudio for the selectedchannel. No action required. Thismessage should disappearshortly. Sat Fault/SIRIUSsystem failure There is an internalmodule or system failurepresent. If this message ...

AUXILIARY INPUT JACK WARNING: Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus offthe road. Your primary responsibility is the safe operation of yourvehicle. We recommen...

REAR SEAT ENTERTAINMENT SYSTEM (IF EQUIPPED) WARNING: Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus offthe road. Your primary responsibility is the safe operation of ...

Your system does not play the following types of discs: • Optical disc CD-1 • CD-ROM • DVD-ROM mini disc-CDG (audio only, not graphics) Important Notice It is unlawful in most jurisdictions for a person to drive a motor vehiclewhich is equipped with a television viewer or screen that is located inth...

Wired Headphones You can use any standard stereo headphones by plugging them into the1/8–inch (3.5 millimeter) headphone jack on each of the headrest DVDsystems. Remove and save the protective plastic cover to access thejacks. Remember to replace the cover when the jacks are not in use. A/V Input Yo...

D. STOP * : Press this button to stop playing the disc. E. PLAY * : Press this button to play the disc. F. Headphone jack: Plug in your wired headphones with a 1/8-inch (3.5 millimeter) stereo connector plug to listen to audio from theprogram. G. Video input jack (red): Connect an RCA cable to this ...

Note: Different types of batteries have different characteristics. Do not mix different types. Note: Do not mix old and new batteries. Mixing old and new batteries can shorten battery life and cause chemical leaks from the old batteries. Note: Keep the batteries out of the reach of children. If some...

5. SOUND AROUND ON/OFF * : Press this button to turn the FM transmitter off and on. 6. MUTE: Press this button to turn off the sound sent to the headphones. The screen displays that the sound is muted. Pressing the button againrestores sound to the previously set level. This feature is onlyfunctiona...

21. EJECT: Press this button to eject or load a disc. 22. TV-Monitor B * : Press this button to control TV mode of Monitor B. 23. DVD-Monitor B: Press this button to control DVD mode of Monitor B. 24. SOUND AROUND SELECT * : Press this button to select an FM transmitter channel. 25. PIX: Press this ...

Turning the Device On and Off 1. Pivot the screen downward until you reach a comfortable viewing angle. 2. Press POWER on the lower-left corner of the front panel or on the remote control. The controls illuminate when the system is in use. 3. When the device is on and is displaying a picture, pivot ...

• Do not use any discs with labels or stickers attached. The followingmalfunctions may result from using such discs: • The system cannot eject a disc due to a label or sticker peeling offand jamming the eject mechanism. • The system cannot read audio data correctly, such as playbackskipping or no pl...

How to Use the Device On-screen Display Menus Press SETUP on the remote control, and then use CH +, CH -, VOL + and VOL - to navigate the Setup Page. Press ENTER to make a selection, and then VOL - to return to the submenu. Audio This allows the user to control the audio stream in the selected langu...

Default Press SETUP on the remote control, and then navigate to the Default submenu under the Preference page using CH +, CH - and VOL +. Press VOL +, and then press ENTER to carry out the reset. This function does not affect the parental settings. Playing an Audio CD When playing an audio CD, the D...

Skipping Songs Press NEXT on the remote control to move to the next song. Press PREV to move to the beginning of the currently playing song. Press PREV twice to move to the previous song. Selecting a Play Mode You can choose what order the songs play on a disc temporarily. TheFOLDER play mode is the...

• FR (Fast Rewind): Press this button to reverse through the file continuously. There are five speed options to choose: 2X, 4X, 8X,16X, and 32X. • FF (Fast Forward): Press this button to fast forward through the file continuously. There are five speed options to choose: 2X, 4X, 8X,16X, and 32X. • PR...

Compliance Information FCC Notice This device has been tested and found to comply with the limits for aClass B digital device, pursuant to part 15 of the FCC Rules. These limitsare designed to provide reasonable protection against harmfulinterference in a residential installation. This device genera...

Warranty INVISION Automotive Systems Inc., (the “Company”) warrants to theoriginal retail purchaser of this product, when purchased from aparticipating new car dealership, that should this product under normaluse and conditions, be proven defective in material or workmanship,such defect(s) will be r...

GENERAL INFORMATION Make sure you review your device’s manual before using it with SYNC. Support The SYNC support team is available to help you with any questions youcannot answer on your own. Monday-Saturday, 8:30am-9:00pm EST.Sunday, 10:30am-7:30pm EST.In the United States, call: 1–800–392–3673.In...

• Do not leave playing devices in your vehicle during extreme conditionsas it could cause them damage. See your device’s manual for furtherinformation. • Do not attempt to service or repair the system. See your authorizeddealer. For your safety, some SYNC functions are speed-dependent. Their use isl...

To access:1. Press MENU during an active call.2. When Active Call Menu is selected, press OK.3. Scroll to cycle through the following options: When you select: You can: Mute Call? Mute the call. Privacy Switch a call from an active hands-freeenvironment to your cellular phone for a moreprivate conve...

When you select: You can: Call History Access your call history log.1. Press OK to select, then scroll throughyour call history options (incoming, outgoingor missed).2. Press OK when the desired selectionappears in the display.3. Press the phone button to call theselection. Return Exit the current m...

Text Messaging Note: This is a phone-dependent feature. SYNC allows you to receive, send, download and delete text messages.The system can also read incoming text messages to you so that you donot have to take your eyes off the road. Receiving a Text Message Note: This is a phone-dependent feature. ...

Download Unread Msgs allows you to download your unread messages (only) to SYNC. To download the messages, press OK to select. Thedisplay indicates your messages are being downloaded. When complete,SYNC takes you to your inbox. Delete All Messages? allows you to delete current text messages from SYN...

Pre-defined text message options I need more directions I love you Too funny Can’t wait to see you I’m stuck in traffic Accessing Your Phone Settings These are phone-dependent features. Your phone settings allow you toaccess and adjust features such as your ring tone, text messagenotification, modif...

When you select: You can: Modify Phonebook Modify the contents of your phone book (i.e.,add, delete, download). Press OK to selectand scroll between: Add Contacts: Press OK to add more contactsfrom your phone book. Push the desiredcontact(s) on your phone. See your phone’suser guide on how to push c...

System Settings System Settings provide access to your Bluetooth Devices andAdvanced menu features. Use the arrow buttons to scroll through themenu options. The Bluetooth Devices menu allows you to add, connect, delete and set aphone as primary as well as turn your Bluetooth feature on and off. The ...

If you select: You can: Set Bluetooth On/Off Turn the Bluetooth feature on and off.Press OK and scroll to toggle between On andOff. When the desired selection is chosen,press OK. Note: Turning Bluetooth off disconnects all Bluetooth devices and deactivates allBluetooth features. Delete Device Delete...

SYNC APPLICATIONS AND SERVICES (IF EQUIPPED) Note: In order for the following features to work, your cellular phone must be compatible with SYNC. To check your phone’s compatibility, visitwww.SYNCMyRide.com, www.SYNCMyRide.ca or www.syncmaroute.ca. • SYNC Services (if equipped, United States only): ...

Vehicle Health Report WARNING: Always follow scheduled maintenance instructions, regularly inspect your vehicle, and seek repair for any damage or problem you suspect. Vehicle Health Report supplements, but cannotreplace normal maintenance and vehicle inspection. Vehicle HealthReport only monitors c...

To run a report using the phone button:1. Press the phone button to enter Phone Menu.2. Scroll until Vehicle Health is selected and press OK.3. Scroll to select from the following options: Vehicle Health Report options User Preferences:Press OK to selectand enter the menu.Scroll to select from: Auto...

Disconnecting from SYNC Services 1. Press and hold the phone button on the steering wheel.2. Say “Good-bye” from the SYNC Services main menu. SYNC Services quick tips Personalizing You can personalize your Services feature toprovide quicker access to your most used orfavorite information. You can sa...

Note: The AppLink feature is not available if your vehicle is equipped with the MyFord Touch or MyLincoln Touch system. Depending on your display type, you can access AppLink from the mediamenu, the phone menu, or by using voice commands. Once an app isrunning through AppLink, you can control main f...

“USB” “Search song <name>” 1,3 “Search track <name>” 1,3 “Shuffle off” “Shuffle on” “Similar music” “What’s playing?” 1 “<name>” is a dynamic listing, meaning that it could be the name of any desired group, artist, etc. 2 Voice commands which are only available in folder mode. 3 Vo...

Voice command guide “Refine” This allows you to make your previouscommand more specific. For example, if youasked to search and play all music by acertain artist, you could then say “refinealbum” and choose a specific album from thelist to view. If you then select Play, the systemonly plays music fr...

When you select: You can: Select Source SYNC USB: Press OK to access music plugged into your USB port. You can also plugin devices to charge them (if supported byyour device). Once connected, the systemindexes any readable media files. (The timerequired to complete this depends on the sizeof the med...

When you select: You can: Similar Music Play music similar to what is currently playingfrom the USB port. The system uses themetadata information of each song to compilea playlist for you.Press OK to select. The system creates a newlist of similar songs and begins playing. Themetadata tags must be p...

4. Press OK and then scroll to select from: When you select: You can: Add BluetoothDevice * Allows you to pair additional devices to thesystem.1. Press OK to select and press OK againwhen Find SYNC appears in the display.2. Follow the directions in your phone’s userguide to put your phone into disco...

Vehicle Health Report and SYNC Services (Traffic, Directions and Information) issues Issue Possible cause(s) Possible solution(s) I received a textthat the VehicleHealth Report isnot activated. • Your account may not beactivated on thewebsite, OR • You may have the wrong VIN(vehicleidentificationnum...

NAVIGATION CONTROLS WARNING: Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus offthe road. Your primary responsibility is the safe operation of yourvehicle. We recommend...

L. MENU: • Press this button to access the system menu. • Press while the system menu is active to access the menu tabs ofDisplay, Clock, Feedback Settings, System Settings and Valet Mode. M. SOUND: • Press this button to access the sound menu. • Press while the sound menu is active to access the me...

Display mode voice commands “Night” “Auto” “Help” STATUS BARS The top status bar shows thecurrent mode, exterior temperature,time and display icons if you haveenabled Bluetooth or other options. The bottom status bar shows theHome icon and may show the Artistand Title of the currently playingCD, Art...

Only the photograph(s), which meets the following conditions, display: • The file must be 1.5MB or smaller. • The file extension must be .jpe, .jpg or .jpeg. • The file path must be 255 characters or fewer. • Up to 256 files or folders can display in one folder. • The CD or DVD must be ISO 9660 form...

You can say these commands at any time. “Line in” “Voice settings” “Mobile apps” “Help” * See the SYNC chapter for more information on these features. To access a list of all available voice commands, press the I hard button.Select the Help tab on the touchscreen, then the Voice Commands taband choo...

SYSTEM MENU FEATURES Your system offers many menu features, such as allowing you to adjustthe touchscreen brightness, time and language, feedback and systemsettings. You can access these options by pressing the MENU hardbutton. If you select: You can: Display Brightness allows you to adjust screen b...

ENTERTAINMENT Your system offers many media options. You can access these optionsusing the touchscreen or voice commands. AM/FM Radio Press the RADIO hard button. To change between AM, FM1 and FM2, touch the AM or FMtab. You can also access satellite radio by pressing this button. See Sirius satelli...

When you select: You can: Show Presets View the preset stations. Save a station bypressing and holding one of the memorypreset areas. There is a brief mute while theradio saves the station. Sound returns whenfinished. Set PTY/All Select a category of music you would like tosearch for and then choose...

HD Radio™ Information (If Available) Note: HD Radio broadcasts are not available in all markets. HD Radio technology is the digital evolution of analog AM/FM radio. Yoursystem has a special receiver that allows it to receive digital broadcasts(where available) in addition to the analog broadcasts, i...

When you select: You can: Tune Go up and down the frequency in individualincrements.If the current station has multiple digitalbroadcasts, the multicast indicator appears.Press Tune repeatedly to advance through allavailable broadcasts. If you are on the lastbroadcast channel, press to advance to th...

HD Radio Reception and Station Troubleshooting Potential Reception Issues Reception area If you are listening to a multicast station andyou are on the fringe of the reception area,the station may mute due to weak signalstrength.If you are listening to HD1, the systemswitches back to the analog broad...

HD Radio Voice Commands If you are listening to the radio, press the voice button on thesteering wheel control. When prompted, say any of thecommands in the following chart. If you are not listening to the radio, press the voice button and, after thetone, say “Radio”, then any of the commands in the...

Sirius® Satellite Radio Voice Commands If you are listening to Sirius satellite radio, press the voicebutton on the steering wheel control. When prompted, say anyof the commands in the following chart. If you are not listening to Sirius satellite radio, press the voice buttonand, after the tone, say...

Sirius® Information Note: Sirius reserves the unrestricted right to change, rearrange, add or delete programming including canceling, moving or adding particularchannels, and its prices, at any time, with or without notice to you. FordMotor Company shall not be responsible for any such programming c...

Troubleshooting tips Radio Display Condition Possible Action Acquiring... Radio requires morethan two seconds toproduce audio for theselected channel. No action required.This message shoulddisappear shortly. Sat Fault/SiriusSystem Failure There is an internalmodule or systemfailure present. If this ...

Troubleshooting tips Radio Display Condition Possible Action No Channels Available. All the channels in the selected channels areeither skipped orlocked. Use the channel guideto turn off the Lock or Skip function on that station. Subscription Updated. Sirius has updated thechannels available foryour...

CD Voice Commands If you are listening to a CD, press the voice button on thesteering wheel control. When prompted, say any of thecommands in the following chart. If you are not listening to a CD, press the voice button and, after thetone, say “CD”, then any of the commands in the following chart. “...

DVD Note: Your system only plays NTSC formatted discs. The system does not support PAL format. Your system allows you to play DVD audio and video discs. Make sureyour vehicle is in position P (vehicles equipped with an automatic transmission) or the parking brake is engaged (vehicles equipped with a...

During disc play, you can also touchthe screen to access the virtualremote, which allows you to MoveControls on the screen, as well asuse the cursor controls, Enter andReturn to navigate and select withinthe menus. Dolby noise reduction is manufactured under license from DolbyLaboratories Licensing ...

DVD Voice Commands If you are watching a DVD, press the voice button on thesteering wheel control. When prompted, say any of thecommands in the following chart. If you are not watching a DVD, press the voice button and, after thetone, say “DVD”, then any of the commands in the following chart. “DVD”...

Jukebox Your system has a Jukebox feature, which allows you to save desiredtracks or CDs to the hard drive for later access. The hard drive can storeup to 10 GB* (164 hours; approximately 2472 tracks) of music. Thesystem contains a Gracenote media database that allows for display ofsong title, album...

When you select: You can: Music library Access all of your saved music. You canchoose to view or play the material in thefollowing ways: Play All Tracks allows you to play all tracks saved in the jukebox. Playlist allows you to play your own playlist. Play genre allows you to have the system play on...

4. Select the desired songs and then press Add. The system shows you the currently selected songs. You can choose to Edit Name to changethe name of the playlist, Delete Playlist to remove it, Add Tracks tothe playlist or Sort Playlist. 5. After you change the playlist, select Edit Name to rename you...

Line In (Auxiliary Input Jack) Your vehicle is equipped with an audio input jack, which allows you toplug a portable audio device into your vehicle’s audio system. To turnthis feature on, press the MEDIA hard button on the system. For more information on the auxiliary input jack, see Auxiliary input...

Press the I (information) button, then select Sirius Travel Link.Choose from any of the following services: When you select: You can: Traffic On Route Identify traffic incidents on your route, nearbyyour vehicle’s current location or near any ofyour favorite places (if programmed). Traffic Nearby My...

Route Guidance in Incompletely Mapped Areas There are some rural areas in the map database without fully verifiedroads. When the system is in route guidance mode, and the navigationsystem encounters these incompletely mapped areas, the system alertsyou by: • Announcing, “Entering an area with incomp...

Standard Note: Items on this screen are selectable only when your vehicle is moving at speeds slower than 5 mph (8 km/h). Address Book You can store up to 25 entries, which you canuse as destinations, waypoints and areas toavoid. You can sort the entries alphabetically,by date or icon. * PreviousDes...

Standard Note: Items on this screen are selectable only when your vehicle is moving at speeds slower than 5 mph (8 km/h). FreewayEntrance/Exit Touch this button to select an entrance andexit point to a freeway you select. You can sortthe entrance and exit point alphabetically or inorder of distance ...

Subcategories Parking Public Transit Home & Garden Education Personal Care Services Setting Your Navigation Preferences Select settings for the system to take into account when planning yourroute. Press the NAV hard button. Map Preferences Map Content Street Name displays current street name dur...

Avoid Areas Add Add items and areas that you want thesystem to avoid when creating a route foryou. The system does its best to avoid these. * * There may be some situations where it is impossible to avoid the selection(s) completely. For example, if a destination or waypoint islocated in the area th...

Map Scale The map display scale has 17 levels, ranging from0.02 miles (.03 kilometers) to 1000 miles (1600 kilometers).The system synchronizes the zoom scales for North Up,Heading Up and 3D Map views. In Map Mode, you can zoom in or out, changing the displayscale, by touching an arrow button on the ...

Quick-touch Buttons When in map mode, touch anywhere on the map display to access thefollowing options: When you select: You can: Set as Dest Select a scrolled location on the map as yourdestination. You may scroll the map bypressing your index finger on the map display.When you reach the desired lo...

Symptoms Possible Cause Action A pop-up windowdisplays “Navigationfault. A system faulthas been detected thatmay cause thenavigation to performabnormally. Pleasecontact yourdealership.” There is a systemhardware or softwareerror. Contact an authorizeddealer. A pop-up windowdisplays “Error. PINsdid n...

GENERAL INFORMATION SYNC® End User License Agreement (EULA) • You have acquired a device (“DEVICE”) that includes software licensed by Ford Motor Company and its affiliates (“FORD MOTORCOMPANY”) from an affiliate of Microsoft Corporation (“MS”). Thoseinstalled software products of MS origin, as well...

SOFTWARE’s ability to use WMDRM to play or copy protectedcontent. This action does not affect unprotected content. When yourDEVICE downloads licenses for protected content, you agree thatMicrosoft may include a revocation list with the licenses. Contentowners may require you to upgrade the SOFTWARE ...

property rights in and to the content which may be accessed through useof the SOFTWARE is the property of the respective content owner andmay be protected by applicable copyright or other intellectual propertylaws and treaties. This EULA grants you no rights to use such content.All rights not specif...

Adobe Contains Adobe® [Flash® Player] or [AIR®] technology by AdobeSystems Incorporated. This [Licensee Product] contains [Adobe® Flash®Player] [Adobe® AIR®] software under license from Adobe SystemsIncorporated, Copyright 娀 1995-2009 Adobe Macromedia Software LLC. All rights reserved. Adobe, Flash ...

General operation Voice Command Control Functions within the Windows Automotive-based system may beaccomplished using only voice commands. Using voice commands whiledriving allows you to operate the system without removing your handsfrom the wheel. Prolonged Views of Screen Do not access any functio...

Route Safety Do not follow the route suggestions if doing so would result in an unsafeor illegal maneuver, if you would be placed in an unsafe situation, or ifyou would be directed into an area that you consider unsafe. The driveris ultimately responsible for the safe operation of the vehicle andthe...

Data, and may not transfer or distribute it in any form, for any purpose,except to the extent permitted by mandatory laws. Restrictions: Except where you have been specifically licensed to do so by (Licensee), and without limiting the preceding paragraph, you maynot (a) use this Data with any produc...

with, and with all licenses and approvals required under, applicableexport laws, rules and regulations. Termination for Breach or Bankruptcy: (Licensee) and its licensors, including NAVTEQ, may terminate this Agreement if you breach any ofits terms. Upon any such termination, you shall immediately c...

Gracenote® Copyright CD and music — related data from Gracenote, Inc., copyright 娀 2000–2007 Gracenote. Gracenote Software, copyright 娀 2000–2007 Gracenote. This product and service may practice one or more of thefollowing U.S. Patents #5,987,525; #6,061,680; #6,154,773, #6,161,132,#6,230,192, #6,23...

GENERAL MAINTENANCE INFORMATION Why Maintain Your Vehicle? Carefully following the maintenance schedule helps protect against majorrepair expenses resulting from neglect or inadequate maintenance andmay help to increase the value of your vehicle when you sell or trade it.Keep all receipts for comple...

Protecting Your Investment Maintenance is an investment that pays dividends in the form ofimproved reliability, durability and resale value. To maintain the properperformance of your vehicle and its emission control systems, make sureyou have scheduled maintenance performed at the designated interva...

NORMAL SCHEDULED MAINTENANCE AND LOG The following section contains the Normal Scheduled Maintenance. Thisschedule is presented at specific mileage (kilometer) intervals withexceptions as noted. Normal scheduled maintenance Every 7500 miles(12000 km) or sixmonths (whichevercomes first) Change engine...

Other maintenance items Every 30000 miles(48000 km) Replace climate-controlled (heated andcooled) seat filter (if equipped). Replace engine air filter. Every 97500 miles(156000 km) Replace spark plugs. Every 105000 miles(168000 km) Change engine coolant. * Inspect accessory drive belt(s). ** Every 1...

Maintenance Schedule Log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ...

Extensive idling or low-speed driving for long distances as in heavy commercial use (such as delivery, taxi, patrol car or livery) Inspect frequently,service as required Replace engine air filter. Every 5000 miles(8000 km) Inspect brake system. Inspect wheels and related components forabnormal noise...

Off-road operation Inspect frequently,service as required Inspect steering linkage, ball joints andU-joints. Lubricate if equipped with greasefittings. Replace engine air filter. Every 5000 miles(8000 km) Change engine oil and filter. * Inspect the wheels and related components forabnormal noise, we...

Special Operating Condition Log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D A...

EXCEPTIONS Normal vehicle axle maintenance: Rear axles and power take-off units with synthetic fluid and light-duty trucks equipped withFord-design axles are lubricated for life; do not check or change fluidunless a leak is suspected, service is required or the assembly has beensubmerged in water. D...

ENGINE COOLANT CHANGE RECORD Initial change Six years or 105000 miles (168000 km)(whichever comes first) After initial change Every three years or 45000 miles (72000 km) Engine Coolant Change Log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C O...

911 Assist™ ..............................400 A ABS (see Brakes) .....................200 Accessing call history/phonebook during active call .............389 Accessing the help screen .......460 Accessing the music in yourjukebox ......................................454 Accessing your media menufe...

U Universal garage door opener ..154 USB port ....................................361 Using privacy mode ..................389 V Vehicle health report ................403 Vehicle Identification Number(VIN) ..........................................342 Vehicle loading ..........................216 Ve...