Ford 2013 Transit Connect v.2- User Manual

DATA RECORDING Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, st...

Additionally, when you connect to Traffic, Directions andInformation (if equipped, U.S. only), the service uses GPStechnology and advanced vehicle sensors to collect the vehicle’scurrent location, travel direction, and speed (“vehicle travelinformation”), only to help provide you with the directions...

REPLACEMENT PARTS RECOMMENDATION Your vehicle has been built to the highest standards using quality parts.We recommend that you demand the use of genuine Ford and Motorcraftparts whenever your vehicle requires scheduled maintenance or repair.You can clearly identify genuine Ford and Motorcraft parts...

SPECIAL NOTICES New Vehicle Limited Warranty For a detailed description of what is covered and what is not coveredby your vehicle’s New Vehicle Limited Warranty, see the warrantyinformation that is provided to you along with your owner’s manual. Special Instructions For your added safety, your vehic...

MOBILE COMMUNICATIONS EQUIPMENT Using mobile communications equipment is becoming increasinglyimportant in the conduct of business and personal affairs. However,you must not compromise your own or others’ safety when using suchequipment. Mobile communications can enhance personal safety andsecurity ...

GENERAL INFORMATION See the following sections for directions on how to properly use safetyrestraints for children. WARNING: Always make sure your child is secured properly in a device that is appropriate for their height, age and weight. Child safety restraints must be bought separately from your v...

Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommendedrestraint type Smallchildren Children who have outgrown or nolonger properly fit in a child safetyseat (generally children who are lessthan 4 ft. 9 in. (1.45 m) tall, aregreater than age four (4) and les...

Note: The child seat must rest tightly against the vehicle seat upon which it is installed. It may be necessary to lift or remove the headrestraint. See the Seats chapter for information on head restraints. BOOSTER SEATS WARNING: Never place, or allow a child to place, the shoulder belt under a chil...

Types of Booster Seats • Backless booster seats If your backless booster seat has a removable shield, remove the shield.If a vehicle seating position has a low seat back or no head restraint, abackless booster seat may place your child’s head (as measured at thetops of the ears) above the top of the...

Perform the following steps when installing the child seat withcombination lap and shoulder belts: Note: Although the child seat illustrated is a forward-facing child seat, the steps are the same for installing a rear-facing child seat. 1. Position the child safety seat in aseat with a combination l...

4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear a snap and feel the latchengage. Make sure the tongue islatched securely by pulling on it. 5. To put the retractor in theautomatic locking mode, grasp...

This is necessary to remove the remaining slack that will exist once theextra weight of the child is added to the child restraint. It also helpsto achieve the proper snugness of the child seat to your vehicle.Sometimes, a slight lean toward the buckle will additionally help toremove remaining slack ...

Follow the instructions on attaching child safety seats with tether straps.Refer to Using Tether Straps later in this chapter. Attach LATCH lower attachments of the child seat only to the anchorsshown. Combining Safety Belt and LATCH Lower Anchors for AttachingChild Safety Seats When used in combina...

The rear seating positions of your vehicle are equipped with built-intether strap anchors located behind the seats on the d-pillar in the cargoarea as described below. The tether strap anchors in your vehicle are in the following positions(shown from top view): • Four-passenger vehicle • Five-passen...

Front passenger seating position The tether can be attached directly to the rear of the front seat. 1. Route the tether strap under the head restraint and between the headrestraint posts. 2. Clip the tether strap to theanchor as shown. Second row center seating position The tether can be attached di...

3. Clip the tether strap to theanchor as shown. Second-row outboard seating positions Note: Place the head restraint underneath the back of the front seat for storage. 1. Remove the head restraint. 2. Locate the correct anchor for the selected seating position. • On five-passenger vehicles,anchors a...

3. Clip the tether strap to theanchor as shown. If the tether strap is clipped incorrectly, the child safety seat may not beretained properly in the event of a collision. 4. Tighten the child safety seat tether strap according to themanufacturer’s instructions. If the safety seat is not anchored pro...

PRINCIPLES OF OPERATION WARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a crash. WARNING: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a crash, people riding in t...

FASTENING THE SAFETY BELTS The front outboard and rear safety restraints in your vehicle arecombination lap and shoulder belts. 1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until you hear a snap and feelit latch. Make sure the tongue i...

Restraint of Pregnant Women WARNING: Always ride and drive with your seat back upright and the safety belt properly fastened. The lap portion of the safety belt should fit snug and be positioned low across the hips. The shoulderportion of the safety belt should be positioned across the chest. Pregna...

Safety Belt Extension Assembly WARNING: Do not use extensions to change the fit of the shoulder belt across the torso. If the safety belt is too short when fully extended, you can obtain asafety belt extension assembly from an authorized dealer. Use only extensions manufactured by the same supplier ...

Deactivating and Activating the Belt-Minder® Feature WARNING: While the design allows you to deactivate your Belt-Minder®, this system is designed to improve your chances of being safely belted and surviving an accident. We recommend you leavethe Belt-Minder system activated for yourself and others ...

CHILD RESTRAINT AND SAFETY BELT MAINTENANCE Inspect the vehicle safety belts and child safety seat systems periodicallyto make sure they work properly and are not damaged. Inspect the vehicleand child seat safety belts to make sure there are no nicks, tears or cuts.Replace if necessary. All vehicle ...

PERSONAL SAFETY SYSTEM™ The Personal Safety System provides an improved overall level of frontalcrash protection to front seat occupants and is designed to help furtherreduce the risk of airbag-related injuries. The system is able to analyzedifferent occupant conditions and crash severity before act...

The airbags are a supplemental restraint system and are designed towork with the safety belts to help protect the driver and right frontpassenger from certain upper body injuries. Airbags do not inflate slowly;there is a risk of injury from a deploying airbag. Note: You will hear a loud bang and see...

DRIVER AND PASSENGER AIRBAGS WARNING: Never place your arm or any objects over an airbag module. Placing your arm over a deploying airbag can result in serious arm fractures or other injuries. Objects placed on or over theairbag inflation area may cause those objects to be propelled by theairbag int...

Proper Driver and Front Passenger Seating Adjustment WARNING: The National Highway Traffic Safety Administration recommends a minimum distance of at least 10 inches (25 centimeters) between an occupant’s chest and the driver airbagmodule. To properly position yourself away from the airbag: • Move yo...

Note: The indicator lamp will illuminate for a short period of time when the ignition is turned to the on position to confirm it is functional. The front passenger sensing system is designed to disable (will notinflate) the front passenger’s frontal airbag when a rear facing infantseat, a forward-fa...

Occupant Pass Airbag OffIndicator Lamp Passenger Airbag Empty Unlit Disabled Small child Lit Disabled Adult Unlit Enabled Note: When the passenger airbag off light is illuminated, the passenger (seat mounted) side airbag may be disabled to avoid the risk of airbagdeployment injuries. After all occup...

If it is necessary to modify an advanced front airbag system toaccommodate a person with disabilities, contact the Ford CustomerRelationship Center at the phone number shown in the Customer Assistance section of this Owner’s Manual. SIDE AIRBAGS WARNING: Do not place objects or mount equipment on or...

CRASH SENSORS AND AIRBAG INDICATOR WARNING: Modifying or adding equipment to the front end of your vehicle (including frame, bumper, front end body structure and tow hooks) may affect the performance of the airbag system,increasing the risk of injury. Do not modify the front end of yourvehicle. Your...

The safety belt pretensioners and the airbag supplemental restraintsystem are designed to activate when the vehicle sustains longitudinal orlateral deceleration sufficient to cause the restraints control module todeploy a safety device or when a certain likelihood of a rollover event isdetected by t...

GENERAL INFORMATION ON RADIO FREQUENCIES This device control complies with part 15 of the FCC Rules and withIndustry Canada license-exempt RSS standard(s). Operation is subjectto the following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any inte...

Integrated Keyhead Transmitter (IKT) 1. Carefully insert a flat object(e.g. a screwdriver) into the recesson the back of the key and removethe key blade. 2. Release the retaining clips with aflat object and separate the twohalves of the transmitter. 3. Carefully pry out the battery witha flat object...

LOCKING AND UNLOCKING You can use the remote control to lock and unlock the vehicle. Central Locking and Unlocking Note: Your vehicle can be configured to unlock only the front doors. See your authorized dealer for more details. • Turn the key toward the front of the vehicle to unlock the front ands...

Open the left hand door second bysqueezing the handle to unlatch thedoor and pulling it open. Note: The dual rear doors should be closed before driving your vehicle. Leaving the doors open could cause serious damage to them and theircomponents. The left door must be closed first. 60 Locks 2013 Trans...

Opening the Doors Fully Push the yellow button located onthe door and swing it open. Thecheck arms will automaticallyre-engage when the doors areclosed. OPENING THE SLIDING DOOR Note: The right-hand sliding door is inhibited from opening fully when the fuel filler flap is unlocked and open. Locks 61...

SECURILOCK® PASSIVE ANTI-THEFT SYSTEM (IF EQUIPPED) Note: The system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle startingproblems and a loss of security protection. Note: Metallic objects, electronic devices or a second coded key on th...

Automatic Disarming Your vehicle disarms when you switch the ignition on with a coded key. Replacement Keys If your keys are lost or stolen and you don’t have an extra coded key,you will need to have your vehicle towed to an authorized dealer. Thekey codes need to be erased from your vehicle and new...

ADJUSTING THE STEERING WHEEL WARNING: Do not adjust the steering wheel when your vehicle is moving. Note: Make sure that you are sitting in the correct position. See Sitting in the Correct Position in the Seats chapter. 1. Unlock the steering column. 2. Adjust the steering wheel to thedesired positi...

AUDIO CONTROL (IF EQUIPPED) Volume Press to increase or decrease thevolume. Seek, Next or Previous Press the seek button to: • tune the radio to the next orprevious stored preset • play the next or previous track. Press and hold the seek button to: • tune the radio to the next stationup or down the ...

Mode Press to select the audio source. VOICE CONTROL (IF EQUIPPED) A. Voice recognition B. Receive a call C. End a call See the SYNC chapter. CRUISE CONTROL (IF EQUIPPED) See the Cruise Control chapter. VOICE SEEK VOL VOL MODE VOICE SEEK VOL VOL MODE A B C OFF ON SET RES Steering Wheel 67 2013 Trans...

WINDSHIELD WIPERS Note: Fully defrost the windshield before switching on the windshield wipers. Note: Make sure the windshield wipers are switched off before entering car wash. Note: Clean the windshield and wiper blades if they begin to leave streaks or smears. If that does not resolve the issue, i...

WINDSHIELD WASHERS Note: Do not operate the washers when the washer reservoir is empty. This may cause the washer pump to overheat. The washer will spray for as long asthe lever is pressed in. After yourelease the lever, the wipers willoperate for a short time. REAR WINDOW WIPER AND WASHER (IF EQUIP...

LIGHTING CONTROL A. Off B. Parking lamps, instrument panellamps, license plate lamps and taillamps C. Headlamps D. Refer to Front Fog Lamps if equipped. E. Refer to Rear Fog Lamp if equipped. High Beams With the head lamps turn on: • Pull the lever fully past the detentto switch the high beams on. •...

INSTRUMENT LIGHTING DIMMER Use to adjust the brightness of theinstrument panel and all applicableswitches in the vehicle duringheadlamp and parking lampoperation. Move the control from left to rightto increase the brightness. Move thecontrol from right to left to reducethe brightness. DAYTIME RUNNIN...

REAR FOG LAMP (IF EQUIPPED) The headlamp control operates therear fog lamp. You can switch therear fog lamp on when the lightingcontrol is in any position except off. Pull the headlamp control towardsyou until you feel the second detentto turn the rear fog lamp on. Therear fog lamp indicator light w...

POWER WINDOWS (IF EQUIPPED) WARNING: Do not leave children unattended in your vehicle and do not let children play with the power windows. They may seriously injure themselves. WARNING: When closing the power windows, you should verify they are free of obstructions and make sure that children and pe...

EXTERIOR MIRRORS Power Exterior Mirrors (If Equipped) WARNING: Do not adjust the mirror while your vehicle is in motion. A. Left mirror B. Off C. Right mirror To adjust your mirrors: 1. Select the mirror you want to adjust. 2. Move the control in the direction you want to tilt the mirror. 3. Return ...

The image of the approaching vehicleis small and near the inboard edge ofthe main mirror when it is at adistance. The image becomes largerand begins to move outboard acrossthe main mirror as the vehicleapproaches (A). The image willtransition from the main mirror andbegin to appear in the blind spot...

Auto-Dimming Mirror (If Equipped) Note: Do not block the sensors on the front and back of the mirror. Mirror performance may be affected. A rear center passenger or raisedrear center head restraint may also block light from reaching the sensor. The mirror will dim automatically to reduce glare when ...

GAUGES Cluster shown in standard measure – metric clusters similar. A. Tachometer B. Engine coolant temperature gauge C. Fuel gauge D. Speedometer E. Information display. See Information displays for more information. A D E B C 78 Instrument Cluster 2013 Transit Connect (tst) Owners Guide gf, 2nd Pr...

Engine Coolant Temperature Gauge Shows the temperature of the engine coolant. At normal operatingtemperature, the needle will remain in the center section. If the needleenters the red section, the engine is overheating. Stop the engine, switchthe ignition off and determine the cause once the engine ...

Anti-Lock Braking System If it illuminates when you are driving, this indicates amalfunction. You will continue to have the normal brakingsystem (without ABS) unless the brake warning lamp is also illuminated. Have the system checked by your authorized dealer. Anti-Theft System Flashes when the Secu...

Direction Indicator Illuminates when the left or right turn signal or the hazardwarning flasher is turned on. If the indicators stay on or flashfaster, check for a burned out bulb. Door Ajar Displays when the ignition is on and any door is not completelyclosed. Engine Oil If it illuminates with the ...

Low Fuel Level It will illuminate when the fuel level is low or near empty.Refuel as soon as possible. Low Tire Pressure Warning It illuminates when your tire pressure is low. If the lampremains on with the engine running or when driving, checkyour tire pressure as soon as possible. The lamp also il...

Service Engine Soon If the service engine soon indicator light stays illuminated afterthe engine is started, it indicates that the On Board Diagnosticssystem (OBD-II) has detected a malfunction of the vehicle emissions control system. Refer to On board diagnostics (OBD-II) in the Fuel and Refueling ...

TRIP COMPUTER Note: The information display will remain on for several minutes after you switch off the ignition. A. Distance to empty B. Trip odometer C. Odometer D. Reset button If SHON or SHIP ON is displayed, the vehicle shipping mode is switchedon. Have your dealer switch off the vehicle shippi...

GENERAL INFORMATION Radio Frequencies and Reception Factors AM and FM frequencies are established by the Federal CommunicationsCommission (FCC) and the Canadian Radio and TelecommunicationsCommission (CRTC). Those frequencies are: AM: 530, 540–1700, 1710 kHz FM: 87.9–107.7, 107.9 MHz Radio reception...

MP3 Track and Folder Structure Audio systems capable of recognizing and playing MP3 individual tracksand folder structures work as follows: • There are two different modes for MP3 disc playback: MP3 trackmode (system default) and MP3 folder mode. • MP3 track mode ignores any folder structure on the ...

L. FF: Press this button to manually fast forward in a CD track or MP3 file. M. REW: Press this button to manually rewind in a CD track or MP3 file. N. Memory presets: Store your favorite radio stations. To store a radio station, tune to the station, then press and hold a preset button untilsound re...

MANUAL CLIMATE CONTROL A. Temperature control: Controls the temperature of the air circulated in your vehicle. Adjust to select the desired temperature. B. Air distribution control: Adjust to select the desired air distribution. Select to distribute air through the instrument panel air vents. Select...

SITTING IN THE CORRECT POSITION WARNING: Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the passenger sensing system, resulting inserious injury or death in a crash. Always sit upright against your seatba...

Rear Seat Outboard Head Restraints The head restraints consist of: A. An energy absorbing head restraint B. Two steel stems C. Guide sleeve adjust and release button D. Guide sleeve unlock and remove button Adjusting the Head Restraint Raise: Pull up the head restraint. Lower: 1. Press and hold butt...

MANUAL SEATS WARNING: Never adjust the driver’s seat or seat back when the vehicle is moving. WARNING: Rock the seat backward and forward after releasing the lever to make sure that it is fully engaged. Moving the Seat Backward andForward Adjust the Height of the Driver’sSeat Recline Adjustment 102 ...

WARNING: Reclining the seat back can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. Manual Lumbar The lumbar control is located onthe inboard side of the seat back.Turn the control to adjust yoursupport. REAR SEATS Folding ...

Returning the seat to the upright position WARNING: Before returning the seat back to its original position, make sure that cargo or any objects are not trapped behind the seat back. After returning the seat back to its original position, pull on theseat back to make sure that it has fully latched. ...

AUXILIARY POWER POINTS WARNING: Do not plug optional electrical accessories into the cigarette lighter socket (if equipped). Improper use of the lighter can cause damage not covered by your warranty, and can result in fireor serious injury. Note: If used when the engine is not running, the battery w...

CENTER CONSOLE Stow items in the cupholder carefully as items may become loose duringhard braking, acceleration or collisions, including hot drinks which mayspill. Available console features include: • Cupholders • Storage area • Power window switches OVERHEAD CONSOLE Overhead Storage Shelf WARNING:...

GENERAL INFORMATION WARNING: Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system, creating the risk of fire or other damage. WARNING: Do not park, idle, or drive your vehicle on dry grass or other dry ground cover. The emission system heats up th...

IGNITION SWITCH (IF EQUIPPED) 0 (Off): The ignition is off. Note: When you switch the ignition off and leave your vehicle, do not leave your key in the ignition. This could cause your vehicle battery tolose charge. I (Accessory): Allows the electrical accessories, such as the radio, to operate while...

We recommend that you do the following for safe and correct operation: • Use a 16-gauge outdoor extension cord that is product certifiedby Underwriter’s Laboratory or Canadian Standards Association.This extension cord must be able to be used outdoors, in coldtemperatures, and be clearly marked Suita...

SAFETY PRECAUTIONS WARNING: Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. WARNING: The fuel system may be under pressure. If you hear a hissing sound near the fuel filler inlet, do not refuel until the sound stops. Otherwise, fue...

• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes,remove contact lenses (if worn), flush with water for 15 minutes andseek medical attention. Failure to seek proper medical attention couldlead to permanent injury. • Fuels can also be harmful if absorbed through the skin. If f...

RUNNING OUT OF FUEL Avoid running out of fuel because this situation may have an adverseeffect on powertrain components. If you have run out of fuel: • You may need to cycle the ignition from off to on several times afterrefueling to allow the fuel system to pump the fuel from the tank tothe engine....

Fuel filler cap Your fuel tank filler cap has an indexed design with a 1/4 turn on/offfeature. When fueling your vehicle: 1. Turn the engine off. 2. Unlock the fuel filler door. 3. Carefully turn the filler cap counterclockwise until it spins off. 4. Pull to remove the cap from the fuel filler pipe....

4. Subtract your initial odometer reading from the current odometerreading. 5. Calculate fuel economy as follows: Standard: Divide miles traveled by gallons used. Metric: Multiply liters used by 100, then divide by kilometers traveled. Keep a record for at least one month and record the type of driv...

AUTOMATIC TRANSMISSION WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the off position and remove the key whenever you leave your vehicle. Your vehicle has been designed to improve fuel economy by reducingfuel usage while coasting...

Brake-Shift Interlock WARNING: Do not drive your vehicle until you verify that the brake lamps are working. WARNING: When doing this procedure, you will be taking the vehicle out of park which means the vehicle can roll freely. To avoid unwanted vehicle movement, always fully set the parkingbrake pr...

Automatic Transmission Adaptive Learning This feature is designed to increase durability and provide consistentshift feel over the life of the vehicle. A new vehicle or transmission mayhave firm shifts, soft shifts or both. This operation is considered normaland will not affect function or durabilit...

GENERAL INFORMATION Note: Occasional brake noise is normal. If a metal-to-metal, continuous grinding or continuous squeal sound is present, the brake linings maybe worn out and should be inspected by an authorized dealer. If yourvehicle has continuous vibration or shudder in the steering wheel while...

PRINCIPLES OF OPERATION The traction control system helps avoid drive wheel spin and loss oftraction. If your vehicle begins to slide, the system applies the brakes to individualwheels and, when needed, reduces engine power at the same time. If thewheels spin when accelerating on slippery or loose s...

PRINCIPLES OF OPERATION WARNING: Vehicle modifications involving braking system, aftermarket roof racks, suspension, steering system, tire construction or wheel and tire size may change the handlingcharacteristics of the vehicle and may adversely affect the performanceof the AdvanceTrac® system. In ...

A Vehicle without AdvanceTrac® with RSC® skidding off its intendedroute. B Vehicle with AdvanceTrac® with RSC® maintaining control on aslippery surface. USING ADVANCETRAC® WITH RSC® The system automatically activates when you start your engine.The AdvanceTrac® with RSC® system cannot be completely t...

SENSING SYSTEM (IF EQUIPPED) WARNING: To help avoid personal injury, please read and understand the limitations of the system as contained in this section. Sensing is only an aid for some (generally large and fixed)objects when moving in reverse on a flat surface at parking speeds.Traffic control sy...

Using the Rear Sensing System The rear sensors are only active when the transmission is in R . As the vehicle moves closer to the obstacle, the rate of the audible warningincreases. When the obstacle is fewer than 12 inches (30 centimeters)away, the warning sounds continuously. If a stationary or re...

REAR VIEW CAMERA SYSTEM (IF EQUIPPED) WARNING: The camera system is a reverse aid supplement device that still requires the driver to use it in conjunction with the rear view mirror and the side mirrors for maximum coverage. WARNING: Objects that are close to either corner of the bumper or under the...

Note: When towing, the camera only sees what is being towed behind the vehicle. This might not provide adequate coverage as it usuallyprovides in normal operation and some objects might not be seen.In some vehicles, the guidelines may disappear once the trailer towconnector is engaged. Note: The cam...

PRINCIPLES OF OPERATION Cruise control lets you maintain a set speed without keeping your footon the accelerator pedal. USING CRUISE CONTROL (IF EQUIPPED) WARNING: Do not use cruise control in heavy traffic or on roads that are winding, slippery or unpaved. Note: Vehicle speed may vary momentarily w...

STEERING To help prevent damage to the power steering system: • Never hold the steering wheel at its furthest turning points (until itstops) for more than a few seconds when the engine is running. • Do not operate the vehicle with a low power steering pump fluid level(below the MIN mark on the reser...

LOAD LIMIT Vehicle loading This section will guide you in the proper loading of your vehicle to keepyour loaded vehicle weight within its design rating capability. Properlyloading your vehicle will provide maximum return of vehicle designperformance. Before loading your vehicle, familiarize yourself...

WARNING: Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tires with ahigher limit than the original tires do not increase the GVWR andGAWR limitations. WARNING: Exceeding any vehicle ...

TOWING A TRAILER WARNING: Never tow a trailer with this vehicle. Your vehicle is not equipped to tow. No towing packages are available through an authorized dealer. WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assis...

TOWING THE VEHICLE ON FOUR WHEELS Emergency Towing If your vehicle becomes inoperable (without access to wheel dollies,car-hauling trailer, or flatbed transport vehicle), it can be flat-towed(all wheels on the ground, regardless of the powertrain and transmissionconfiguration) under the following co...

BREAKING-IN You need to break in new tires for approximately 300 miles(480 kilometers). During this time, your vehicle may exhibit some uniquedriving characteristics. Avoid driving too fast during the first 1000 miles(1600 kilometers). Vary your speed frequently and change up throughthe gears early....

• Use the speed control in hilly terrain. • Rest your foot on the brake pedal while driving. • Drive a heavily loaded vehicle or tow a trailer. • Carry unnecessary weight (approximately 1 mpg [0.4 km/L] is lost forevery 400 pounds [180 kilograms] of weight carried). • Add particular accessories to y...

FLOOR MATS WARNING: Always use floor mats that are designed to fit the footwell of your vehicle. Only use floor mats that leave the pedal area unobstructed. Only use floor mats that are firmly secured toretention posts so that they cannot slip out of position and interferewith the pedals or impair s...

WARNING (Continued) • Check attachment of floor mats on a regular basis. Always properlyreinstall and secure floor mats that have been removed for cleaningor replacement. • Always make sure that objects cannot fall into the driver footwellwhile the vehicle is moving. Objects that are loose can becom...

ROADSIDE ASSISTANCE Vehicles Sold in the U.S.: Getting Roadside Assistance To fully assist you should you have a vehicle concern, Ford Motor Companyoffers a complimentary roadside assistance program. This program isseparate from the New Vehicle Limited Warranty. The service is available: • 24 hours ...

Vehicles Sold in the U.S.: Using Roadside Assistance Complete the roadside assistance identification card and place it in yourwallet for quick reference. This card is found in the owner’s manualportfolio in the glove compartment. U.S. Ford vehicle customers who require Roadside Assistance,call 1-800...

FUEL CUT-OFF SWITCH WARNING: Failure to inspect and if necessary repair fuel leaks after a collision may increase the risk of fire and serious injury. Ford Motor Company recommends that the fuel system be inspected byan authorized dealer after any collision. In the event of a moderate to severe coll...

Preparing Your Vehicle Note: Use only a 12–volt supply to start your vehicle. Note: Do not disconnect the battery of the disabled vehicle as this could damage the vehicle’s electrical system. 1. Park the booster vehicle close to the hood of the disabled vehiclemaking sure the two vehicles do not tou...

1. Connect the positive (+) jumpercable to the positive (+) terminal ofthe discharged battery. 2. Connect the other end of thepositive (+) cable to the positive (+)terminal of the assisting battery. 3. Connect the negative (-) cable tothe negative (-) terminal of theassisting battery. 4. Make the fi...

Removing the Jumper Cables Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery. Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable fromthe ground metal surface. 2. Remove the jumper cable on thenega...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizeddealer. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfaction. Plea...

• Ford Genuine Accessories • Service specials and promotions. In Canada: Mailing address Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6K 0C8 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Additional Assistance If you have questions or concerns,...

UTILIZING THE MEDIATION or ARBITRATION PROGRAM(CANADA ONLY) This pertains to vehicles delivered to authorized Canadian dealers.In those cases, where you continue to feel that the efforts by Ford ofCanada and the authorized dealer to resolve a factory-related vehicleservice concern have been unsatisf...

CHANGING A FUSE Electric vehicles For specific information on the Transit Connect Electric, refer to the Azure Dynamics TC-E Owner’s Guide Supplement. Fuses WARNING: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wir...

COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 60A — — Blue Yellow Yellow 70A — — Tan — Brown 80A — — Natural Black Black FUSE SPECIFICATION CHART Power Distribution Box WARNING: Always disconnect the battery before servicing high current fuses. WARNI...

GENERAL INFORMATION Have your vehicle serviced regularly to help maintain its roadworthinessand resale value. There is a large network of Ford authorized dealerswho are there to help you with their professional servicing expertise.We believe that their specially trained technicians are best qualifie...

Working with the Engine On WARNING: To reduce the risk of vehicle damage or personal burn injuries, do not start your engine with the air cleaner removed and do not remove it while the engine is running. 1. Set the parking brake and shift to position P . 2. Block the wheels. Electric vehicles For sp...

UNDER HOOD OVERVIEW A. Engine coolant reservoir B. Engine oil filler cap C. Brake fluid reservoir D. Battery E. Power distribution box F. Windshield washer fluid reservoir G. Air filter assembly H. Automatic transmission fluid dipstick I. Engine oil dipstick J. Power steering fluid reservoir A B C D...

ENGINE OIL DIPSTICK ENGINE OIL CHECK Refer to the Scheduled Maintenance information for the appropriate intervals for checkingthe engine oil. 1. Make sure the vehicle is on levelground. 2. Turn the engine off and wait15 minutes for the oil to drain intothe oil pan. 3. Set the parking brake and ensur...

Adding Engine Oil Note: Do not remove the filler cap when the engine is running. Note: Do not add engine oil further than the MAX mark. Oil levels above the MAX mark may cause engine damage. Only use oils certified for gasoline engines by theAmerican Petroleum Institute (API). An oil with thistradem...

Note: For best results, coolant concentration should be tested with a refractometer such as Rotunda tool 300-ROB75240 available from yourdealer. Ford does not recommend the use of hydrometers or coolant teststrips for measuring coolant concentrations. Note: Automotive fluids are not interchangeable;...

• In case of emergency, a large amount of water without engine coolantmay be added in order to reach a vehicle service location. In thisinstance, the cooling system must be drained, chemically cleaned withMotorcraft Premium Cooling System Flush, and refilled with enginecoolant as soon as possible. W...

If you drive in extremely hot climates: • It may be necessary to have a Ford authorized dealer decrease thecoolant concentration to 40%. • A coolant concentration of 40% will provide improved overheatprotection. Engine coolant concentrations below 40% will decrease thecorrosion/freeze protection cha...

When fail-safe mode is activated You have limited engine power when in the fail-safe mode, so drive thevehicle with caution. The vehicle will not be able to maintain high speedoperation and the engine will run rough. Remember that the engine iscapable of completely shutting down automatically to pre...

BRAKE FLUID CHECK Fluid levels between the MIN and MAX lines are within the normaloperating range; there is no need to add fluid. If the fluid levels areoutside of the normal operating range, the performance of the systemcould be compromised; seek service from your authorized dealerimmediately. POWE...

State or local regulations on volatile organic compounds may restrictthe use of methanol, a common windshield washer antifreeze additive.Washer fluids containing non-methanol antifreeze agents should be usedonly if they provide cold weather protection without damaging thevehicle’s paint finish, wipe...

6. Drive the vehicle to complete the relearning process. • The vehicle may need to be driven 10 miles (16 km) or more torelearn the idle and fuel trim strategy. • Note: If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle ...

AIR FILTER CHECK WARNING: To reduce the risk of vehicle damage and or personal burn injuries, do not start your engine with the air cleaner removed and do not remove it while the engine is running. Note: Failure to use the correct air filter element may result in severe engine damage. The customer w...

4. Locate the vertical adjuster oneach headlamp. Using a Phillips #2screwdriver or a 13 millimetersocket on a wrench, turn theadjuster either clockwise orcounterclockwise in order to adjustthe vertical aim of the headlamp.The horizontal edge of the brighterlight should touch the horizontalreference ...

Replacing Headlamp Bulbs WARNING: Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb by only its plastic base and do not touch the glass. The oil from your hand could cause thebulb to break the next time the headlamps are operated. Note: If the bulb is accident...

Replacing side repeater bulbs 1. Make sure the headlamp controlis in the off position. 2. Remove the side repeater byprying it out from the bottom. 3. Hold the bulb holder and turn itcounterclockwise to remove it. 4. Pull the bulb straight out. Install in reverse order. Replacing Tail/Brake/Rear Fog...

Replacing License Plate Lamp Bulbs 1. Make sure the headlamp controlis in the off position. 2. Remove the lens assembly. 3. Pull the bulb straight out. Install in reverse order. Replacing Front Dome Lamp Bulb 1. Make sure the headlamp switch isin the off position. 2. Switch off the interior lamps. 3...

WAXING • Wash the vehicle first. • Use a quality wax that does not contain abrasives. • Do not allow paint sealant to come in contact with any non-body(low-gloss black) colored trim, such as grained door handles, roofracks, bumpers, side moldings, mirror housings or the windshield cowlarea. The pain...

4. Remove the soaked cloth, and if it is not soiled badly, use this cloth toclean the area by using a rubbing motion for 60 seconds. 5. Following this, wipe area dry with a clean, white, cotton cloth. CLEANING LEATHER SEATS (IF EQUIPPED) • Remove dust and loose dirt with a vacuum cleaner. • Clean sp...

VEHICLE STORAGE If you plan on storing your vehicle for an extended period of time(30 days or more), read the following maintenance recommendations tomake sure your vehicle stays in good operating condition. All motor vehicles and their components were engineered and tested forreliable, regular driv...

Removing Vehicle from Storage When your vehicle is ready to come out of storage, do the following: • Wash your vehicle to remove any dirt or grease film build-up onwindow surfaces. • Check windshield wipers for any deterioration. • Check under the hood for any foreign material that may have collecte...

GENERAL INFORMATION Notice to Utility Vehicle, Van and Truck Owners WARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles. To reduce the risk of serious injury or death from a rollover or other crash you must: • Avoid sharp turns and abrupt maneuvers; • Dri...

How Your Vehicle Differs from Other Vehicles Sport-utility vehicles, vans andtrucks can differ from some othervehicles in a few noticeable ways.Your vehicle may be: • Higher – to allow higher loadcarrying capacity and to allow it totravel over rough terrain withoutgetting hung up or damagingunderbod...

TIRE CARE Information About Uniform Tire Quality Grading Tire Quality Grades apply to newpneumatic passenger car tires. The TireQuality Grades can be found whereapplicable on the tire sidewall betweentread shoulder and maximum sectionwidth. For example: • Treadwear 200 Traction AA Temperature A Thes...

Traction AA A B C Note: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering,hydroplaning or peak traction characteristics. The traction grades, from highest to lowest are AA, A, B, and C.The grades represent the tir...

INFORMATION CONTAINED ON THE TIRE SIDEWALL Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. This informationidentifies and describes the fundamental characteristics of the tire and alsoprovides a U.S. DOT Tire Identifi...

F. 95: Indicates the tire’s load index. It is an index that relates to how much weight a tire can carry. You may find this information in yourowner’s manual. If not, contact a local tire dealer. Note: You may not find this information on all tires because it is not required by federal law. G. H: Ind...

Information on T Type Tires T type tires have some additionalinformation beyond those of P typetires. These differences aredescribed below. T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Gradesdo not apply to thi...

INFLATING YOUR TIRES Safe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air pressurewithout appearing flat. Every day before you drive, check your tires. If one looks lower than theothers, use a tire gauge to check pressure o...

Maximum Inflation Pressure is the tire manufacturer’s maximum permissible pressure or the pressure at which the maximum loadcan be carried by the tire. This pressure is normally higher than themanufacturer’s recommended cold inflation pressure, which can be foundon the Safety Compliance Certificatio...

Note: Some spare tires operate at a higher inflation pressure than the other tires. For T-type mini-spare tires, see the Dissimilar Spare Tire and Wheel Assembly Information section. Store and maintain at 60 psi (4.15 bar). For full-size and dissimilar spare tires, see the Dissimilar Spare Tire and ...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire Wear When the tread is worn down to1/16th of an inch (2 millimeters),tires must be replaced to...

U.S. DOT Tire Identification Number Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. This informationidentifies and describes the fundamental characteristics of the tire andalso provides a U.S. DOT Tire Identification ...

Safety Practices WARNING: If your vehicle is stuck in snow, mud, or sand, do not rapidly spin the tires. Spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. WARNING: Do not spin the wheels at over 35 mph (56 km/h). The tires may fail...

Tire Rotation WARNING: If the tire label shows different tire pressures for the front and rear tires and the vehicle is equipped with a tire pressure monitoring system, then the settings for the system sensorsneed to be updated. Always perform the system reset procedure aftertire rotation. If the sy...

USING SNOW CHAINS WARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety and performanceof your vehicle, which could result in an increased risk of loss of vehiclecontrol, vehicl...

TIRE PRESSURE MONITORING SYSTEM WARNING: The tire pressure monitoring system is NOT a substitute for manually checking tire pressure. The tire pressure should be checked periodically (at least monthly) using a tire gauge.See Inflating Your Tires in this chapter. Failure to properly maintain your tir...

replacing one or more tires or wheels on your vehicle to ensure that thereplacement or alternate tires and wheels allow the TPMS to continue tofunction properly. The tire pressure monitoring system complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject tothe ...

When you believe your system is not operating properly The main function of the tire pressure monitoring system is to warn youwhen your tires need air. It can also warn you in the event the system isno longer capable of functioning as intended. See the following chart forinformation concerning your ...

Low tirepressurewarning light Possible cause Customer action required Flashingwarning light Spare tire in use Repair the damaged road wheel and tire and reinstall it on thevehicle to restore system function.For a description on how thesystem functions, see When your temporary spare tire is installed...

Tire pressure monitoring system reset procedure WARNING: To determine the required pressure for your vehicle, refer to the Safety Compliance Certification Label or Tire Label located on the B-Pillar or the edge of the driver’s door. See Vehicle loading in this chapter for more information. Note: The...

CHANGING A ROAD WHEEL WARNING: The use of tire sealants may damage your tire pressure monitoring system and should not be used. However, if you must use a sealant, the tire pressure monitoring system sensor andvalve stem on the wheel must be replaced by an authorized Ford dealer. WARNING: See Tire P...

• Winter weather driving capability • Wet weather driving capability • All-wheel driving capability (if applicable) • Load leveling adjustment (if applicable) When driving with the full-size dissimilar spare tire and wheel assembly,additional caution should be given to: • towing a trailer. • driving...

TECHNICAL SPECIFICATIONS Wheel Lug Nut Torque Specifications WARNING: When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum orbrake disc that contacts the wheel. Make sure that any f...

ENGINE SPECIFICATIONS Engine 2.0L I4 engine Cubic inches 121 Required fuel Minimum 87 octane Firing order 1–3–4–2 Ignition system C.O.P Compression ratio 10.0:1 Spark plug gap .051 inch +/- .002(1.3 mm +/- .05) Engine drivebelt routing Capacities and Specifications 243 2013 Transit Connect (tst) Own...

MOTORCRAFT PART NUMBERS Component 2.0L I4 engine Engine air filter element FA-1900 Oil filter FL-910S 1 Battery BXT-96R-590 Spark plugs 2 Cabin air filter FP38 1 Only use the specified replacement oil filter. The use of a non-specified oil filter can result in engine damage. 2 For spark plug replace...

The Vehicle Identification Number (VIN) contains the following information: A. World manufacturer identifier B. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintDevices and their location C. Make, vehicle line, series, bodytype D. Engine type E. Check digit F. Model year G. Assembly plant...

ACCESSORIES For a complete listing of the accessories that are available for yourvehicle, please contact your dealer or visit our online store at: Accessories.Ford.com (U.S. only). Ford Custom Accessories are available for your vehicle through yourlocal Ford or Ford of Canada dealer. Ford Motor Comp...

FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY) More than 32 million Ford and Lincoln owners have discovered thepowerful protection of Ford ESP. It is the only extended service planbacked by Ford Motor Company, and provides “peace of mind”protection beyond the New Vehicle Limited Warranty coverage. Up t...

FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY) You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is the only service contractbacked by Ford Motor Company of Canada, Limited. Depending on theplan you purchase, Ford ESP provides benefits such as: • r...

GENERAL MAINTENANCE INFORMATION Electric vehicles For specific information on the Transit Connect Electric, refer to the Azure Dynamics TC-E Owner’s Guide Supplement. Why Maintain Your Vehicle? Carefully following the maintenance schedule helps protect against majorrepair expenses resulting from neg...

Convenience Many dealerships have extended evening and Saturday hours to makeyour service visit more convenient and they offer one stop shopping.They can perform any services that are required on your vehicle, fromgeneral maintenance to collision repairs. Note: Not all dealers have extended hours or...

Oils, Fluids and Flushing In many cases, fluid discoloration is a normal operating characteristicand, by itself, does not necessarily indicate a concern or that the fluidneeds to be changed. However, discolored fluids that also show signsof overheating and foreign material contamination should be in...

NORMAL SCHEDULED MAINTENANCE AND LOG The following section contains the Normal Maintenance Schedule.This schedule is presented at specific mileage (kilometer) intervalswith exceptions as noted. Normal Scheduled Maintenance Every 7500 miles(12000 km) orsix months (whichevercomes first) Change engine ...

Additional Maintenance Items Every 30000 miles(48000 km) Replace engine air filter. Every 37500 miles(60000 km) Inspect valve clearances. Adjust as necessary(CNG vehicles). Every 97500 miles(156000 km) Replace spark plugs. Every 105000 miles(168000 km) Change engine coolant. * Inspect accessory driv...

Maintenance Schedule Log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ...

Extensive Idling or Low-speed Driving for Long Distances as in Heavy Commercial Use (i.e., Delivery, Taxi, Patrol Car or Livery) Every 5000 miles(8000 km) or sixmonths Change engine oil and filter. Every 30000 miles(48000 km) Change automatic transmission fluid. Every 60000 miles(96000 km) Replace s...

Special Operating Condition Log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D A...

EXCEPTIONS California fuel filter replacement: If the vehicle is registered in California, the California Air Resources Board has determined that thefailure to perform this maintenance item will not nullify the emissionwarranty or limit recall liability prior to the completion of the vehicle’suseful...

Engine Coolant Change Log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M...

Support The SYNC support team is available to help you with any questions youcannot answer on your own. Monday-Saturday, 8:30am-8:00pm EST In the United States, call: 1–888–270–1055 In Canada, call: 1–800–565–3673 Times are subject to change due to holidays. SYNC Owner Account Why do I need a SYNC o...

When using SYNC: • Do not operate playing devices if the power cords or cables arebroken, split or damaged. Place cords and cables out of the way,so they do not interfere with the operation of pedals, seats,compartments or safe driving abilities. • Do not leave playing devices in your vehicle during...

To access:1. Press MENU during an active call.2. When Active Call Menu is selected, press OK.3. Scroll to cycle through the following options: When you select: You can: Mute Call? Mute the call. Privacy Switch a call from an active hands-freeenvironment to your cellular phone for a moreprivate conve...

When you select: You can: Call History Access your call history log.1. Press OK to select, then scroll throughyour call history options (incoming, outgoingor missed).2. Press OK when the desired selectionappears in the display.3. Press the phone button to call theselection. Return Exit the current m...

When you select: You can: Phonebook ** Allows you to access your downloadedphonebook.1. Press OK to confirm and enter. If yourphonebook has fewer than 255 listings, theyappear alphabetically in flat file mode. If thereare more, they are organized into alphabeticalcategories.2. Scroll until the desir...

Receiving a Text Message Note: This is a phone-dependent feature. Your phone must support downloading text messages using Bluetooth to receive incoming textmessages. Note: Forwarding a text message is a speed-dependent feature and can only be done when the vehicle is traveling at 3 mph (5 km/h) or l...

Note: SYNC does not automatically download all of your unread text messages at every ignition cycle (as it does with call history andphonebook if automatic download is set to on). Return exits the current menu when you press OK. If you select Send Text Message? : 1. Press OK to select. If the system...

When you select: You can: Modify Phonebook Modify the contents of your phone book(i.e., add, delete, download). Press OK toselect and scroll between: Add Contacts: Press OK to add more contactsfrom your phone book. Push the desiredcontact(s) on your phone. See your phone’suser guide on how to push c...

System Settings System Settings provide access to your Bluetooth Devices andAdvanced menu features. Use the arrow buttons to scroll through themenu options. The Bluetooth Devices menu allows you to add, connect, delete and set aphone as primary as well as turn your Bluetooth feature on and off. The ...

If you select: You can: Set Bluetooth On/Off Turn the Bluetooth feature on and off.Press OK and scroll to toggle between On andOff. When the desired selection is chosen,press OK. Note: Turning Bluetooth off disconnects all Bluetooth devices and deactivates allBluetooth features. Delete Device Delete...

4. Scroll to select from the following options: If you select: You can: Prompts Get help from SYNC by using questions,helpful hints or asking you for a specificaction. To turn these prompts on or off:1. Press OK to select and scroll to selectbetween on or off.2. Press OK when the desired selectionap...

If you select: You can: Install Application Install applications you have downloaded.Press OK and scroll to select. Press OK toconfirm. System Info Access the Auto Version number as well asthe FPN number.Press OK to select. MAP Profile This is a Bluetooth component which canfurther help your phone w...

“USB” “Play track <name>” 1,3 “Refine album <name>” 1,3 “Refine artist <name>” 1,3 “Refine song <name>” 1 “Refine track <name>” 1,3 “Repeat off” “Repeat on” “Search album <name>” 1,3 “Search artist <name>” 1,3 “Search genre <name>” 1,3 “Search song <...

Press the voice icon and when prompted say “Bluetooth Audio” and thenany of the following: “BLUETOOTH AUDIO” “(Phone) (Media) (Bluetooth) Connections” “Pause” “Play” “Play next track ” “Play previous track ” Media Menu Features The media menu allows you to select your media source, how to playyour m...

When you select: You can: Select Source SYNC USB: Press OK to access music plugged into your USB port. You can also plug indevices to charge them (if supported by yourdevice). Once connected, the system indexesany readable media files. (The time required tocomplete this depends on the size of the me...

When you select: You can: Media Settings Choose to shuffle or repeat your music andselect your Autoplay settings. Once theseselections are turned on, they remain on untilturned off. Press SEEK to play the previousor next track. Note: Some digital media players require both USB and line in ports to s...

When you select: You can: Explore USB Explore all supported digital media on yourmedia device connected to the USB port. Youcan only view media content which iscompatible with SYNC; other files saved arenot visible.Press OK to select. Then scroll to exploreindexed media on your flash drive. Similar ...

Advanced Menu Options This menu allows you to access settings such as prompts, language,performing a master reset as well as returning to factory defaults.1. Press AUX and then MENU to access the Media Menu.2. Scroll until System Settings appears and select OK.3. Scroll until Advanced appears.4. Pre...

When you select: You can: Master Reset Completely erase all information stored onSYNC (all phonebook, call history, textmessages and all paired devices) and returnto the factory default settings. Application Download new software applications(if available) and then load the desiredapplications throu...

GENERAL INFORMATION SYNC® End User License Agreement (EULA) • You have acquired a device (“DEVICE”) that includes software licensed by Ford Motor Company and its affiliates (“FORD MOTOR COMPANY”)from an affiliate of Microsoft Corporation (“MS”). Those installed softwareproducts of MS origin, as well...

DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS: • Speech Recognition: If the SOFTWARE includes speech recognition component(s), you should understand that speech recognition is aninherently statistical process and that recognition errors are inherentin the process. Neither FORD MOTOR COMPANY nor its su...

• Security Updates/Digital Rights Management: Content owners use the WMDRM technology included in your DEVICE to protect theirintellectual property, included copyrighted content. Portions of theSOFTWARE on your DEVICE use WMDRM software to accessWMDRM-protected content. If the WMDRM software fails t...

INTELLECTUAL PROPERTY RIGHTS: All title and intellectual property rights in and to the SOFTWARE (including but not limited to any images,photographs, animations, video, audio, music, text and “applets,”incorporated into the SOFTWARE), the accompanying printed materials,and any copies of the SOFTWARE...

No Liability for Certain Damages: EXCEPT AS PROHIBITED BY LAW, FORD MOTOR COMPANY, ANY THIRD PARTY SOFTWARE ORSERVICES SUPPLIERS, MS, MICROSOFT CORPORATION AND THEIRAFFILIATES SHALL HAVE NO LIABILITY FOR ANY INDIRECT,SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISINGFROM OR IN CONNECTION WITH THE ...

WARNING: Operating certain parts of this system while driving can distract your attention away from the road, and possibly cause an accident or other serious consequences. Do not changesystem settings or enter data non-verbally (using your hands) whiledriving. Stop the vehicle in a safe and legal ma...

A ABS (see Brakes) .....................125 Accessing call history/phonebook during active call .............278 Accessing your media menufeatures ......................................293 Accessing your phone menufeatures ......................................280 Active call menu options .........2...