Ford 2013 F-150 v.1- User Manual

ABOUT THIS MANUAL Thank you for choosing Ford. We recommend that you take some time toget to know your vehicle by reading this manual. The more that youknow about it, the greater the safety and pleasure you will get fromdriving it. WARNING: Always drive with due care and attention when using and ope...

SYMBOL GLOSSARY WARNING: You risk death or serious injury to yourself and others if you do not follow the instruction highlighted by the warning symbol. These are some of the symbols you may see on your vehicle. Symbol Description Symbol Description Symbol Description Safety alert See Owner’sManual ...

Ford Motor Company, Ford of Canada, and service and repair facilitiesmay access or share among them data for vehicle improvement purposes.For U.S. only (if equipped), if you choose to use the SYNC 威 Vehicle Health Report, you consent that certain diagnostic information may alsobe accessed electronic...

they have access to the vehicle or the EDR. Ford Motor Companyand Ford of Canada do not access event data recorderinformation without obtaining consent, unless pursuant to courtorder or where required by law enforcement, other governmentauthorities or other third parties acting with lawful authority...

PERCHLORATE MATERIAL Note: Certain components in your vehicle, such as airbag modules, safety belt pretensioners, and remote control batteries, may containperchlorate material. Special handling may apply for service or vehicleend of life disposal. See www.dtsc.ca.gov/hazardouswaste/perchlorate formo...

Warranty on Replacement Parts Genuine Ford and Motorcraft replacement parts are the onlyreplacement parts that benefit from a Ford Warranty. Damage caused toyour vehicle as a result of the failure of non-Ford parts may not becovered by the Ford Warranty. For additional information, see the termsand ...

MOBILE COMMUNICATIONS EQUIPMENT Using mobile communications equipment is becoming increasinglyimportant in the conduct of business and personal affairs. However, youmust not compromise your own or others’ safety when using suchequipment. Mobile communications can enhance personal safety andsecurity ...

GENERAL INFORMATION See the following sections for directions on how to properly use safetyrestraints for children. WARNING: Always make sure your child is secured properly in a device that is appropriate for their height, age and weight. Child safety restraints must be bought separately from your v...

Recommendations for Safety Restraints for Children Child size, height, weight, orage Recommendedrestraint type Smallchildren Children who have outgrown or nolonger properly fit in a child safetyseat (generally children who areless than 4 ft. 9 in. (1.45 m) tall,are greater than age four (4) andless ...

Note: The child seat must rest tightly against your vehicle seat. It may be necessary to lift or remove the head restraint. See the Seats chapter for information on head restraints. BOOSTER SEATS WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the bac...

Types of Booster Seats • Backless booster seats If your backless booster seat has a removable shield, remove the shield.If a vehicle seating position has a low seat back or no head restraint, abackless booster seat may place your child’s head (as measured at thetops of the ears) above the top of the...

Perform the following steps when installing the child seat withcombination lap and shoulder belts: Note: Although the child seat illustrated is a forward facing child seat, the steps are the same for installing a rear facing child seat. 1. Position the child safety seat in aseat with a combination l...

4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear a snap and feel the latchengage. Make sure the tongue islatched securely by pulling on it. 5. To put the retractor in theautomatic locking mode, grasp...

This is necessary to remove the remaining slack that will exist once theextra weight of the child is added to the child restraint. It also helps toachieve the proper snugness of the child seat to your vehicle.Sometimes, a slight lean toward the buckle will additionally help toremove remaining slack ...

9. Check from time to time to be sure that there is no slack in the lapand shoulder belt. The shoulder belt must be snug to keep the lap belttight during a collision. Ford recommends checking with a NHTSA Certified Child PassengerSafety Technician (CPST) to make certain the child restraint is proper...

LATCH attachments cannot be installed at the center seating position.LATCH compatible child seats (with attachments on belt webbing) canonly be used at this seating position provided that the child seatmanufacturer’s instructions permit use with the anchor spacing stated.Do not attach a child seat t...

The tether strap anchors in your vehicle are in the following positions(shown from top view): • F-150 Regular Cab • F-150 SuperCrew and SuperCab Attach the tether strap only to the appropriate tether anchor as shown.The tether strap may not work properly if attached somewhere otherthan the correct t...

Front Seat Tether Strap Attachment (Regular Cab) 1. Route the child safety seat tether strap over the back of the seat andunder the head restraint. For vehicles with adjustable head restraints, route the tether strap underthe head restraint and between the head restraint posts, otherwise routethe te...

Rear Seat Tether Strap Attachment (SuperCab and SuperCrew) There are three loops of webbingjust above the back of the rear seat(along the bottom edge of the rearwindow). These loops are to beused as both routing loops andanchor loops for up to three childsafety seat tether straps. For example, the c...

• Always put the tether strap through the routing loop. The headrestraint support post will hold the child seat tightly, but the headrestraint post is not strong enough to hold the child seat during acollision. 3. Tighten the tether strap according to the child seat manufacturer’sinstructions. If th...

PRINCIPLES OF OPERATION WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips. WARNING: To reduce the risk of injury, make sure children sit where they can be properly restrained. WARNING: Never let a passenger hold a child on his or her lap while th...

1. To lengthen the lap belt, pullsome webbing out of the shoulderbelt retractor. 2. While holding the webbing belowthe tongue, grasp the tip (metalportion) of the tongue so that it isparallel to the webbing and slide thetongue upward. 3. Provide enough lap belt length so that the tongue can reach th...

How to disengage the automatic locking mode Disconnect the combination lap and shoulder belt and allow it to retractcompletely to disengage the automatic locking mode and activate thevehicle sensitive (emergency) locking mode. Safety Belt Extension Assembly WARNING: Do not use extensions to change t...

SAFETY BELT WARNING LIGHT AND INDICATOR CHIME This lamp illuminates and an audible warning will sound if thedriver’s safety belt has not been fastened when the vehicle’signition is turned on. Conditions of Operation If... Then... The driver’s safety belt is notbuckled before the ignitionswitch is tu...

CHILD RESTRAINT AND SAFETY BELT MAINTENANCE Inspect the vehicle safety belts and child safety seat systems periodicallyto make sure they work properly and are not damaged. Inspect thevehicle and child seat safety belts to make sure there are no nicks, tearsor cuts. Replace if necessary. All vehicle ...

PERSONAL SAFETY SYSTEM™ The Personal Safety System provides an improved overall level of frontalcrash protection to front seat occupants and is designed to help furtherreduce the risk of airbag-related injuries. The system is able to analyzedifferent occupant conditions and crash severity before act...

PRINCIPLES OF OPERATION WARNING: Airbags DO NOT inflate slowly or gently, and the risk of injury from a deploying airbag is the greatest close to the trim covering the airbag module. WARNING: All occupants of your vehicle, including the driver, should always properly wear their safety belts, even wh...

The airbags are a supplemental restraint system and are designed towork with the safety belts to help protect the driver and right frontpassenger from certain upper body injuries. Airbags DO NOT inflateslowly; there is a risk of injury from a deploying airbag. Note: You will hear a loud bang and see...

DRIVER AND PASSENGER AIRBAGS WARNING: Never place your arm or any objects over an airbag module. Placing your arm over a deploying airbag can result in serious arm fractures or other injuries. Objects placed on or over theairbag inflation area may cause those objects to be propelled by theairbag int...

• Recline the seat slightly (one or two degrees) from the upright position. After all occupants have adjusted their seats and put on safety belts, it isvery important that they continue to sit properly. A properly seatedoccupant sits upright, leaning against the seat back, and centered on theseat cu...

FRONT PASSENGER SENSING SYSTEM WARNING: Even with Advanced Restraints Systems, children 12 and under should be properly restrained in a rear seating position. WARNING: Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the d...

• Other passengers pushing or pulling on the seat • Rear passenger feet and knees resting or pushing on the seat The conditions listed above may cause the weight of a properly seatedoccupant to be incorrectly interpreted by the front passenger sensingsystem. The person in the front passenger seat ma...

Low-series vehicles (if equipped) The front passenger sensing systemuses a pass airbag off indicator whichwill illuminate and stay lit to remindyou that the front passenger frontalairbag is disabled. The indicator lampis located in the center stack of theinstrument panel. Note: The indicator lamp wi...

Occupant Passenger Airbag Off Indicator Lamp Passenger Airbag Empty Unlit Disabled Child Lit Disabled Adult Unlit Enabled Note: When the passenger airbag off lamp is illuminated, the passenger side airbag (seat mounted) may be disabled to avoid the risk of airbagdeployment injuries. After all occupa...

The system consists of thefollowing: • Safety canopy curtain airbagsfitted above the trim panels overthe front and rear side windowsidentified by wording on theB-pillar trim. • A flexible headliner which opensabove the side doors to allow aircurtain deployment. • Crash sensors and monitoring system ...

cluster or by a backup tone if the warning light is not working. See Warning lamps and indicators in the Instrument Cluster chapter. Routine maintenance of the airbag is not required. A difficulty with the system is indicated by one or more of the following: • The readiness light will either flash o...

GENERAL INFORMATION ON RADIO FREQUENCIES This device complies with part 15 of the FCC Rules and with IndustryCanada license-exempt RSS standard(s). Operation is subject to thefollowing two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference...

REMOTE CONTROL Integrated Keyhead Transmitters (IKTs) (If Equipped) Your vehicle may be equipped withtwo integrated keyhead transmitters.The key blade is used to start thevehicle and unlock or lock thedriver’s door from outside thevehicle. The transmitter portionfunctions as the remote control. Note...

Car Finder Press the button twice within three seconds. The horn willchirp and the turn signals will flash. It is recommended thatthis method be used to locate your vehicle, rather than using the panic alarm. Sounding a Panic Alarm Press the button to activate the alarm. Press the button againor tur...

Extending the Vehicle Run Time Repeat Steps 1 and 2 with the vehicle still running to extend the runtime for another remote start duration. If you programmed the durationto last 10 minutes, the second 10 minutes will begin after what is left ofthe first activation time. For example, if the vehicle h...

PRINCIPLES OF OPERATION MyKey 威 allows you to program keys with restricted driving modes to promote good driving habits. All but one of the keys programmed to thevehicle can be activated with these restricted modes. Any keys that havenot been programmed are referred to as an administrator key or adm...

• Audio system maximum volume of 45%. A message in the audiosystem is displayed when attempting to exceed the limited volume. • AdvanceTrac. The system cannot be turned off when Always-on hasbeen set. CREATING A MYKEY Use the information display controls to create a MyKey. For Type 1 information dis...

Programming/Changing Optional Settings Note: All programmed keys can be cleared within the same key cycle in which a key was programmed, otherwise an admin key is required toclear the keys. To clear all keys, see Clearing all MyKeys. You can access the optional settings through the information displ...

LOCKING AND UNLOCKING You can use the power door lock control or the remote control to lockand unlock the vehicle. Power Door Locks (If Equipped) The power door lock control is located on the driver and front passengerdoor panels. A. Unlock B. Lock Remote Control The remote control can be used anyti...

Smart Unlocks (If Equipped) This feature helps to prevent you from locking yourself out of the vehicleif your key is still in the ignition. When you open the driver’s door and lock the vehicle with the powerdoor lock control, all the doors will lock, then the driver’s door willunlock if your key is ...

Programming Memory to a Personal Entry Code To program a personal entry code to recall memory settings, repeatSteps 1-4 above. • Pressing 1 • 2 on the keypad in Step 4 will program the code to driver memory setting 1. • Pressing 3 • 4 in Step 4 will program the code to driver memory setting 2. Note:...

Unlocking and Locking the Doors To unlock the driver’s door: enter the factory set 5-digit code or your personal code. Each number must be pressed within five seconds of eachother. The interior lamps will illuminate. Note: All doors will unlock if the two-stage unlocking feature is disabled. Refer t...

ADJUSTING THE STEERING WHEEL WARNING: Do not adjust the steering wheel when your vehicle is moving. Note: Make sure that you are sitting in the correct position. Refer to Sitting in the Correct Position in the Seats chapter. 1. Unlock the steering column. 2. Adjust the steering wheel to thedesired p...

Type 2 A. Volume up B. Seek up or next C. Media D. Seek down or previous E. Volume down Media Press the media button repeatedly to scroll through available audiomodes. Seek, Next or Previous Press the seek button to: • tune the radio to the next or previous stored preset • play the next or previous ...

CRUISE CONTROL (IF EQUIPPED) See the Cruise Control chapter. INFORMATION DISPLAY CONTROL Type 1 Type 2 See the Information Displays chapter. SET ON OFF RSM CNCL SETUP RESET INFO SET RESET INFO SETUP ON OFF RSM CNCL OK 86 Steering Wheel 2013 F-150 (f12) Owners Guide gf, 1st PrintingUSA (fus)

ADJUSTABLE PEDALS (IF EQUIPPED) WARNING: Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving. The control is located on the left side of the steering column. Press andhold the appropriate control to move the pedals. A. Farther B. Closer The pedal position...

WINDSHIELD WIPERS Note: Fully defrost the windshield in icy conditions before turning on the windshield wipers. Rotate the end of the control awayfrom you to increase the speed ofthe wipers. Rotate toward you todecrease the speed of the wipers. Speed Dependent Wipers (If Equipped) When your vehicle ...

WINDSHIELD WASHERS Note: Do not operate the wipers on a dry windshield. This may scratch the glass, damage the wiper blades or cause the wiper motor to burn out.Always use the windshield washer before wiping a dry windshield. Note: Do not operate the washer when the washer reservoir is empty. This m...

LIGHTING CONTROL • Rotate the headlamp controlclockwise to the first position toturn on the parking lamps. • Rotate clockwise to the secondposition to also turn on theheadlamps. High Beams Pull the lever fully past the detentto switch the high beams on. Pull the lever fully again switch thehigh beam...

AUTOLAMPS (IF EQUIPPED) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the headlamp control. The autolamp system also keeps thelights on for a predeterminedamount of time after the ignitionswitch is turned to off. Using themessage cen...

DAYTIME RUNNING LAMPS (IF EQUIPPED) WARNING: Always remember to switch your headlamps on in low light situations or during inclement weather. The system does not activate the tail lamps and may not provide adequate lightingduring these conditions. Failure to activate your headlamps under thesecondit...

Lane Change To indicate a left or right lane change: • Push the lever up/down to the first stop position and release. The turnsignals will flash three times and stop. • Push the lever up/down to the first stop position and hold. The turnsignals will flash for as long as the lever is held in this pos...

POWER WINDOWS (IF EQUIPPED) WARNING: Do not leave children unattended in the vehicle and do not let them play with the power windows. They may seriously injure themselves. WARNING: When closing the power windows, you should verify they are free of obstructions and make sure that children and pets ar...

Bounce-Back (One-Touch Up or Down Windows Only) The window will stop automatically while closing and reverse somedistance if there is an obstacle in the way. Overriding the Bounce-Back Feature Pull up the window switch and hold within two seconds of the windowreaching the bounce-back position. The w...

The control is located on theoverhead console. Press and hold the control to openthe window. Pull and hold thecontrol to close the window. Accessory Delay (If Equipped) You can use the window switches for several minutes after the youswitch the ignition off, or until either front door is opened. EXT...

Fold-Away Exterior Mirrors Push the mirror toward the door window glass. Make sure that you fullyengage the mirror in its support when returning it to its original position. Power-Folding Mirrors (If Equipped) Note: Activating the mirrors 10 or more times within one minute, or repeated folding and u...

Signal Indicator Mirrors (If Equipped) The rear-facing portion of the appropriate mirror housing will blink whenthe turn signal is activated. Clearance Lamps (If Equipped) The lower, outer portion of the mirror housings illuminates when theheadlamps or parking lamps are switched on. Telescoping Mirr...

Integrated Blind Spot Mirror (If Equipped) WARNING: Objects in the blind spot mirror are closer than they appear. Blind spot mirrors have an integrated convex mirror built into the upperoutboard corner of the exterior mirrors. They are designed to assist youby increasing visibility along the side of...

INTERIOR MIRROR WARNING: Do not adjust the mirror when your vehicle is moving. Note: Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum or ammonia based cleaning products. You can adjust the interior mirror to your preference. Some mirrors alsohave a second...

GAUGES Cluster shown in standard measure. Metric similar. A. Engine oil pressure gauge B. Engine coolant temperature gauge C. Fuel gauge D. Transmission fluid temperature gauge E. Speedometer F. Information display. See Information displays for more information. G. Tachometer Engine Oil Pressure Gau...

Engine Coolant Temperature Gauge Indicates engine coolant temperature. At normal operating temperature,the level indicator will be in the normal range. If the engine coolanttemperature exceeds the normal range, stop the vehicle as soon as safelypossible, switch off the engine and let the engine cool...

Charging System It will illuminate when the 12–volt battery is not charging properly.Contact your authorized dealer as soon as possible. This indicatesa problem with the electrical system or a related component. Check 4X4 Displays with the message CHECK 4X4 when a four-wheel drivefault is present. R...

Engine Coolant Temperature Illuminates when the engine coolant temperature is high. Stop thevehicle as soon as possible, switch off the engine and let cool. Fasten Safety belt It will illuminate and a chime will sound to remind you to fastenyour safety belt. High Beam It will illuminate when the hea...

Service Engine Soon The service engine soon indicator light illuminates when the ignition is first turned to the on position to check the bulb andto indicate whether the vehicle is ready for Inspection/Maintenance (I/M) testing. Normally, the “service engine soon”light will stay on until the engine ...

4X2 Illuminates momentarily when two-wheel drive high is selected.If the light fails to display when the ignition is turned on, orremains on, have the system serviced immediately by your authorized dealer. 4X4 LOW Illuminates when four-wheel drive low is engaged. If the light failsto display when th...

Info Press the INFO button repeatedly to cycle through the following features: Note: Some options may appear slightly different or not at all if the items are optional. INFO TRIP A/B MYKEY MILES (km) (if programmed) MILES (km) TO E AVG MPG (L/100km) MPG (L/km) TIMER TBC GAIN (if equipped) • TRIP A/B...

System Check and Vehicle Feature Customization Press the SETUP button repeatedly to cycle the message center throughthe following features: SETUP RESET FORSYSTEM CHECK press theRESET button XXX% OIL LIFE DOOR STATUS BRAKE SYSTEM FUEL LEVEL LOW TBC GAIN = XX.X or NOTRAILER TBC GAIN = XX.X or OUTPUT =...

SETUP LANGUAGE =ENGLISH /SPANISH /FRENCH press theRESET button English / Spanish / French • RESET FOR SYSTEM CHECK: The message center will begin to cyclethrough the vehicle systems and provide a status of the item ifneeded. Some systems show a message only if a condition is present. • OIL LIFE: Thi...

Main menu You can access the menus using the information display control. • Gauge Mode • Trip A/B • Fuel Economy • Truck Apps (If Equipped) • Settings • Information Gauge Mode Use the arrow buttons to choose between the following gaugeoptions. Gauge Mode Gauges Detail Trans Temp Compass The compass ...

Trip A/ B Use the arrow buttons to choose between the following tripoptions. Trip A/ B Trip time Trip distance Fuel used Avg mpg(L/100km) Odometer (displays in lower line and may display in other menus) Press OK to pause the Trip A or B screen/press again to un-pause. Press and hold OK to reset the ...

• Average MPG: shows the average fuel usage based on time. See FuelHist. to change the time interval. Press and hold OK to reset this value. Truck Apps In this mode, off-road information depicted with graphics andtrailer towing application options are available. Note: Some items are optional and may...

Truck Apps Trailer Trailer disconnected. Disregard this status if your vehicleis not equipped with a factory installed trailer brakecontroller. This message may appear when an aftermarketTBC is used even when the trailer is connected. Active trailer name or default trailer Accumulated trailer distan...

Settings In this mode, you can configure different driver setting choices. Note: Some items are optional and may not appear. Settings DriverAssist Rear Park Aid On/Off Rear VideoCamera Camera Delay On/Off Visual Park Aid On/Off Guidelines Fixed/Off Zoom Levels (Thiswill only be shownwhen Reverse (R)...

Compass: Determine which magnetic zone youare in for your geographic locationby referring to the zone map. Settings MyKey Create MyKey Hold OK to create MyKey AdvanceTrac Always On / Selectable MAX Speed 80 MPH (130 km/h) or Off Speed Warning 45, 55 or 65 MPH(75, 90 or 105 km/h), Off Volume Limiter ...

Information System Check Some items will only display during a system checkif a problem has been detected. If an issue exists onone of the monitored systems, the number ofwarnings that need immediate attention will displayin red and the number of informational warnings willdisplay in amber. Use the ...

AdvanceTrac 威 / Traction Control Messages Action / Description ADVANCETRACSPORT MODE Displayed when the AdvanceTrac 威 sport mode has been enabled by the driver. (SVT Raptor) TRACTIONCONTROL OFF Displayed when the traction control has beendisabled by the driver. Refer to the Traction Control chapter ...

Battery and Charging System Messages Action / Description TURN POWER OFFTO SAVE BATTERY Displayed when the battery managementsystem determines that the battery is at a lowstate of charge or, the ignition has been inaccessory position or on position with theengine off for approximately 45 minutes. Tu...

Door Messages Action / Description X DOOR AJAR Displayed when the corresponding door is notcompletely closed. Drivetrain Messages Action / Description NEUTRAL TOWENABLED LEAVETRANSMISSION INNEUTRAL Displayed when the transfer case is in theneutral position. This message indicates thatthe vehicle is ...

Off Road Messages Action / Description FOR OFF ROADSLOW TO 5 MPH Displayed when the vehicle speed requirementfor off-road mode entry has not been met. OFF ROAD MODEENABLED Displayed when off-road mode becomes active. EXITING OFFROAD MODE Displayed when off-road mode becomesinactive.. HILL DESCENTCON...

Tire Messages Action / Description LOW TIREPRESSURE Displays when one or more tires on yourvehicle have low tire pressure. TIRE PRESSUREMONITOR FAULT Displays when the tire pressure monitoringsystem is malfunctioning. If the warning stayson or continues to come on, contact yourauthorized dealer. TIR...

Trailer Messages Action / Description TRAILER SWAYREDUCE SPEED Displayed when the trailer sway control hasdetected trailer sway. WIRING FAULT ONTRAILER Displayed if there are certain faults in thevehicle wiring and trailer wiring/brake system.Refer to Trailer towing in the Towing chapter for more in...

GENERAL AUDIO INFORMATION Radio Frequencies and Reception Factors AM and FM frequencies are established by the Federal CommunicationsCommission (FCC) and the Canadian Radio and TelecommunicationsCommission (CRTC). Those frequencies are: AM: 530, 540–1700, 1710 kHz FM: 87.9–107.7, 107.9 MHz Radio rec...

Always handle discs by their edges only. Clean the disc with an approvedCD cleaner only, wiping from the center of the disc toward the edge. Donot clean in a circular motion. Do not expose discs to direct sunlight or heat sources for extendedperiods of time. MP3 Track and Folder Structure Audio syst...

Menu Structure Note: Depending on your system, some options may appear slightly different, not at all or on-screen and able to be selected using thefunction buttons.Press MENU.Press the up and down arrow buttons to scroll through the options (ifactive).Press the right arrow to enter a menu. Press th...

AM/FM/CD SONY AUDIO SYSTEM WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that you use extreme caution when using any device or feature that may takeyour focus off the road. Your primary responsibility is the safe operationof th...

• In SIRIUS mode, select the previous or next channel. If a specificcategory is selected, (Jazz, Rock, News, etc.), use the seek buttonsfind to the previous or next channel in the selected category. • In CD mode, select the previous or next track. G. MEDIA: Access different audio modes, such as AM, ...

SATELLITE RADIO INFORMATION (IF EQUIPPED) Satellite Radio Channels SIRIUS 威 broadcasts a variety of music, news, sports, weather, traffic and entertainment satellite radio channels. For more information and acomplete list of SIRIUS 威 satellite radio channels, visit www.siriusxm.com in the United Sta...

MANUAL HEATING AND AIR CONDITIONING SYSTEM A. Defrost: Distributes air through the windshield defroster vents and demister vents. This setting can also be used to defog and clear thewindshield of a thin covering of ice. B. Rear defrost and heated mirrors: Turns the heated windows and mirrors on and ...

MANUAL HEATING AND AIR CONDITIONING SYSTEM A. Fan speed control: Controls the volume of air circulated in your vehicle. Turn to select the desired fan speed or switch off. If you switchthe fan off, the windshield may fog up. B. Rear defrost: Turns the heated windows and mirrors on and off. See Heate...

DUAL AUTOMATIC TEMPERATURE CONTROL SYSTEM Note: You can switch temperature units between Fahrenheit and Celsius. See Menu features in the MyFord Touch or MyLincoln Touch chapter. A. Power/Driver temperature control: Press to turn the climate control system on and off. When the system is off, outside...

GENERAL OPERATING TIPS Manual Heating and Air Conditioning System • To reduce fog build-up on the windshield during humid weather, selectDefrost. Temperature and fan speed can also be increased to improveclearing. • To reduce humidity build-up inside the vehicle, do not drive with thesystem off or w...

Dual Zone Automatic Temperature Control • To reduce fog build-up on the windshield during humid weather, selectDefrost. Temperature and fan speed can also be increased to improveclearing. • To reduce humidity build-up inside the vehicle, do not drive with thesystem off or with recirculated air engag...

Automatic Climate Systems Automatic Settings You can set the climate control to operate in AUTO mode through theinformation display setting: Remote Start > Climate Control > Heater –A/C > Auto. The climate control system automatically sets the interiortemperature to 72°F (22°C). In hot weat...

SITTING IN THE CORRECT POSITION WARNING: Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the passenger sensing system, resulting inserious injury or death in a crash. Always sit upright against your seatba...

Front Seat Center HeadRestraint Your vehicle may be equipped with a front row center head restraint thatis non-adjustable. These head restraints consist of : A. An energy absorbing head restraint B. Two steel stems C. Guide sleeve unlock and remove button Remove 1. Pull up the head restraint until i...

Once it is in its forward-most position, tilting it forward once more willrelease it to the upright position. Note: Do not attempt to force the head restraint backward after it is tilted. Instead, continue tilting it forward until the head restraint releasesto the upright position. MANUAL SEATS Movi...

MEMORY FUNCTION (IF EQUIPPED) WARNING: Before activating the seat memory, make sure that the area immediately surrounding the seat is clear of obstructions and that all occupants are clear of moving parts. WARNING: Do not use the memory store function when your vehicle is moving. This feature will s...

programmed to a memory position. If the easy entry/exit feature isenabled, the mirrors, pedals and steering column will move to theprogrammed memory position and the seat will move to the easy entryposition. The seat will move to the driving memory position when theignition is activated. A programme...

Returning the Seat to the Seating Position WARNING: Make sure that cargo or any objects are not trapped underneath the seat cushion before returning the seat cushion to its original position, and that the seat cushion locks into place. Failureto do so may prevent the seat from operating properly in ...

Heated and Cooled Seats Air Filter Replacement (if equipped) The heated and cooled seat system includes air filters that must bereplaced periodically. See scheduled maintenance information. The filter is located under each front seat. The filter can be accessedfrom the 2nd row foot-well area. Move t...

UNIVERSAL GARAGE DOOR OPENER The appearance of your vehicle’s universal garage door opener will varyaccording to your option package. Before programing, make sure youidentify which transmitter you have by comparing it to the graphicsbelow. HomeLink 威 Car2U 威 Home Automation System Note: The programm...

Rolling Code Programming Note: If you do not follow the time-sensitive instructions, the device will time out and you will have to repeat the complete procedure. Note: It may be helpful to have another person assist you in programming the transmitter. 1. Switch the ignition on. 2. Press and hold the...

8. The LED lamp will begin to flash rapidly until programming iscomplete. If your garage door does not operate, repeat the previoussteps. Otherwise, call the toll-free help line at 1-866-572-2728. The LED lamp above the selected button will illuminate to confirm thatthe system is responding to the b...

4. Press and hold the function button you programmed for 5 seconds,then release. You may need to do this twice to activate the door. If yourgarage door does not operate, observe the indicator light. If the indicator light stays on, programming is complete. Press andrelease the programmed button to a...

Reprogramming a single button To program a device to a previously trained button, follow these steps: 1. Press and hold the desired button. Do NOT release the button. 2. The indicator light will begin to flash after 20 seconds. Withoutreleasing the button, follow Step 1 in the Programming section. F...

AUXILIARY POWER POINTS WARNING: Do not plug optional electrical accessories into the cigarette lighter socket (if equipped). Improper use of the lighter can cause damage not covered by your warranty, and can result in fireor serious injury. Note: If used when the engine is not running, the battery w...

CENTER CONSOLE (IF EQUIPPED) WARNING: Use only soft cups in the cupholder. Hard objects can injure you in a collision. Your vehicle may be equipped with a variety of consoles features. Theseinclude: • Locking storage compartmentwith hanging file folder supports • Utility compartment with coinholder ...

3. Turn the key to start the engine. The engine may continue cranking for up to 15 seconds or until the vehicle starts. Note: If the engine does not start on the first try, wait for a short period of time and try again. If you have difficulty starting the engine when the temperature is below-13°F (-...

We recommend that you do the following for safe and correct operation: • Use a 16-gauge outdoor extension cord that is product certified byUnderwriter’s Laboratory or Canadian Standards Association. Thisextension cord must be able to be used outdoors, in coldtemperatures, and be clearly marked Suita...

SAFETY PRECAUTIONS WARNING: Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. WARNING: The fuel system may be under pressure. If you hear a hissing sound near the fuel filler inlet, do not refuel until the sound stops. Otherwise, fue...

• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes,remove contact lenses (if worn), flush with water for 15 minutes andseek medical attention. Failure to seek proper medical attention couldlead to permanent injury. • Fuels can also be harmful if absorbed through the skin. If f...

Octane recommendations 3.7L V6/5.0L V8/6.2L V8 engines “Regular” unleaded gasoline with a pump (R+M)/2 octane rating of 87 isrecommended. Some stations offer fuels posted as “Regular” with anoctane rating below 87, particularly in high altitude areas. Fuels withoctane levels below 87 are not recomme...

Refilling With a Portable Fuel Container WARNING: Do not insert the nozzle of portable fuel containers or aftermarket funnels into the Easy Fuel 威 system. This could damage the fuel system and its seal, and may cause fuel to run onto theground instead of filling the tank, which could result in serio...

5. After you are done pumping fuel, slowly remove the fuel fillernozzle—allow about ten seconds after pumping fuel before removing thefuel filler nozzle. This allows residual fuel to drain back into the fuel tankand not spill onto the vehicle. 6. Reinstall the plug (if equipped) into the fuel fill i...

For consistent results when filling the fuel tank: • Turn the ignition off before fueling; an inaccurate reading results if theengine is left running. • Use the same fill rate (low–medium–high) each time the tank is filled. • Allow no more than two automatic click–offs when filling. Results are most...

EMISSION CONTROL SYSTEM WARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. WARNING: Exhaust leaks may result in entry of harmful and potentially lethal fumes into th...

AUTOMATIC TRANSMISSION WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the off position and remove the key whenever you leave your vehicle. WARNING: Do not use the tow/haul feature when driving in icy or slippery conditions as the ...

Press the (+)/(–) buttons on the gearshift lever to manually make shifts: • Press (+) on the gearshift leverbutton to manually upshift thetransmission. • Press (–) on the gearshift leverbutton to manually downshift thetransmission. For vehicles equipped with the (+)/(–) buttons on the column shifter...

Although the SST will make some downshifts for you, it will still allowyou to downshift at any time as long as the SST determines that theengine will not be damaged from over-revving. The SST will not automatically upshift, even if the engine is approachingthe RPM limit. It must be shifted manually ...

If the fuse is not blown and the brake lamps are working properly, thefollowing procedure will allow you to move the gearshift lever from P(Park): 1. Apply the parking brake, turn theignition key to the off position, andremove the key. 2. Starting at the rear of the trimpanel, using a screwdriver (o...

USING FOUR-WHEEL DRIVE (4WD) (IF EQUIPPED ) WARNING: For important information regarding safe operation of this type of vehicle, see General Information in the Wheels and Tires chapter. Note: Do not use 4X4 mode on dry, hard surfaced roads. Doing so will produce excessive noise, increase tire wear a...

Using the Electronic Shift on the Fly 4WD system (If Equipped) 2H (4X2) - Delivers power to the rear wheels only. This mode isappropriate for normal on-roaddriving and provides the best fueleconomy and smoothness. 4H (4X4 HIGH) - provides mechanically locked four-wheeldrive power to the front and re...

If SHIFT DELAYED PULL FORWARD is displayed in the message center, transfer case gear tooth blockage is present. To alleviate thiscondition, place the transmission in a forward gear, move the vehicleforward approximately 5 feet (2 meters), and shift the transmission backto neutral to allow the transf...

Activating the Electronic Locking Differential Note: Do not use ELD on dry, hard surfaced roads. Doing so will produce excessive noise and vibration and increase tire wear. Note: If the ELD has difficulty disengaging, release the accelerator pedal and turn the steering wheel in the opposite directio...

For vehicles equipped with a 3.5L Ecoboost™ engine: Your vehicle is equipped with an underbody transmission shield andbrackets that may become damaged (due to reduced ground clearance)when taking your vehicle off-road. Remove the shield by disengaging thefasteners at each corner of the shield. Then,...

GENERAL INFORMATION Note: Occasional brake noise is normal. If a metal-to-metal, continuous grinding or continuous squeal sound is present, the brake linings may beworn-out and should be inspected by an authorized dealer. If yourvehicle has continuous vibration or shudder in the steering wheel while...

PRINCIPLES OF OPERATION The traction control system helps avoid drive wheel spin and loss oftraction. If your vehicle begins to slide, the system applies the brakes to individualwheels and, when needed, reduces engine power at the same time. If thewheels spin when accelerating on slippery or loose s...

PRINCIPLES OF OPERATION WARNING: Vehicle modifications involving braking system, aftermarket roof racks, suspension, steering system, tire construction or wheel/tire size may change the handling characteristicsof the vehicle and may adversely affect the performance of theAdvanceTrac 威 system. In add...

HILL DESCENT CONTROL™ (if equipped) WARNING: Hill descent control cannot control descent in all surface conditions and circumstances, such as ice or extremely steep grades. Hill descent control is a driver assist system and cannotsubstitute for good judgment by the driver. Failure to do so may resul...

SENSING SYSTEM (IF EQUIPPED) WARNING: To help avoid personal injury, please read and understand the limitations of the system as contained in this section. Sensing is only an aid for some (generally large and fixed)objects when moving in reverse on a flat surface at parking speeds.Traffic control sy...

The sensing system warns the driver of obstacles within a certain rangeof the bumper area. The system turns on automatically whenever theignition is switched on. When receiving a detection warning, the radio volume is reduced to apredetermined level. After the warning goes away, the radio volumeretu...

REAR VIEW CAMERA SYSTEM (IF EQUIPPED) WARNING: The rear view camera system is a reverse aid supplement device that still requires the driver to use it in conjunction with the interior and exterior mirrors for maximum coverage. WARNING: Objects that are close to either corner of the bumper or under t...

2. Centerline: Helps align the center of the vehicle with an object (i.e. a trailer). Note: If the image comes on while the transmission is not in R (Reverse), have the system inspected by your authorized dealer. Note: When towing, the camera only sees what is being towed behind the vehicle. This mi...

Guidelines and the Centerline Note: Fixed guidelines are only available when the transmission is in R (Reverse). Note: The centerline is only available if fixed guidelines are on. A. Rear bumper B. Fixed guideline: Red zone C. Fixed guideline: Yellow zone D. Fixed guideline: Green zone E. Centerline...

Manual Zoom WARNING: When manual zoom is on, the full area behind the vehicle is not shown. Be aware of your surroundings when using the manual zoom feature. Note: Manual zoom is only available when the transmission is in R (Reverse). Note: When manual zoom is enabled, only the centerline is shown. ...

PRINCIPLES OF OPERATION Cruise control lets you maintain a set speed without keeping your footon the accelerator pedal. USING CRUISE CONTROL (IF EQUIPPED) WARNING: Do not use cruise control in heavy traffic or on roads that are winding, slippery or unpaved. Note: Vehicle speed may vary momentarily w...

STEERING Electric power steering (3.7L, 5.0L and 3.5L EcoBoost™ engines) WARNING: The electric power steering system has diagnostic checks that continuously monitor the system to ensure proper operation. When a system error is detected the following messageService Power Steering, Service Power Steer...

permanent damage to your steering system. If this should occur, you willneither lose the ability to steer the vehicle manually nor will it causepermanent damage. Typical steering and driving maneuvers will allow thesystem to cool and steering assist will return to normal. When a steering system erro...

LOAD LIMIT Vehicle Loading – With and Without a Trailer This section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehicle weight within its design ratingcapability, with or without a trailer. Properly loading your vehicle willprovide maximum return of vehic...

Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weigh...

either the door hinge pillar, door-latch post, or the door edge thatmeets the door-latch post, next to the driver’s seating position.The GVW must never exceed the GVWR. • Example only: WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substanda...

GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo andpassengers – that the vehicle can handle without r...

WARNING: Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tires with ahigher limit than the original tires do not increase the GVWR andGAWR limitations. WARNING: Exceeding any vehicle ...

TAILGATE Tailgate Lock (If Equipped) The tailgate lock is designed to helpprevent theft of the tailgate. Insert the ignition key into thetailgate lock. Turn it to the right tolock or to the left to unlock thetailgate. Tailgate Removal WARNING: Always properly secure cargo to prevent shifting cargo o...

3. Rotate the panels toward thetailgate. Repeat Steps 1–3 for the other side of the bed extender. 4. Connect the two panels, thenrotate both knobs a quarter-turnclockwise to secure the panels. 5. Make sure the latch rod isinserted into the tailgate hole andthe locking pins on both sides areengaged i...

Automatic Power Stow The running boards will return to the stowed position after a two seconddelay when the doors are closed. Manual Power Deploy To manually operate the running boards, refer to the Information Displays chapter. • This feature can manually set the running boards in the deployed(OUT)...

TOWING A TRAILER WARNING: Do not exceed the GVWR or the GAWR specified on the certification label. WARNING: Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage, transmission damage, structural damage, lossof vehicle c...

TRAILER SWAY CONTROL (IF EQUIPPED) Note: This feature does not prevent trailer sway, but reduces it once it begins. Note: This feature cannot stop all trailers from swaying. Note: In some cases, if vehicle speed is too high, the system may activate multiple times, gradually reducing vehicle speed. T...

SuperCrew Engine Rear axle ratio Maximum GCWR - lb (kg) 5.0L (Heavy DutyPayload Package) 3.73 15300 (6940) 6.2L 3.55 15600 (7076) 6.2L (MAX Trailer Tow Package) 3.73 17100 (7756) ESSENTIAL TOWING CHECKS Follow these guidelines for safe towing: • Do not tow a trailer until your vehicle has been drive...

Integrated Trailer Brake Controller (If Equipped) WARNING: The Ford TBC has only been verified to be compatible with trailers having electric-actuated drum brakes (one to four axles) and some electic-over-hydrualic (EOH) brakes. Itwill not activate hydraulic surge-style trailer brakes. It is theresp...

• TBC GAIN = XX.X OUTPUT = / / / / / /: Displays when the vehicle’s brake pedal is pushed, or when the manual control is activated. Barindicators illuminate in the information display to indicate the amountof power going to the trailer brakes relative to the brake pedal ormanual control input. One b...

2. Hook up the trailer and make the electrical connections according to the trailer manufacturer’s instructions. 3. When a trailer with electric or EOH brakes is plugged in, TRAILER CONNECTED appears in the information display. 4. Use the GAIN adjustment (+/-) buttons to increase or decrease the GAI...

Points to Remember Note: Do not attempt removal of the TBC without consulting the Workshop Manual. Damage to the unit may result. • Adjust GAIN setting before using the TBC for the first time. • Adjust GAIN setting (according to procedure above) whenever road,weather and trailer or vehicle loading c...

Using a Step Bumper (If Equipped) The rear bumper is equipped with an integral hitch and only requires a ballwith a one inch (25.4 millimeter) shank diameter. The bumper has a5000 pound (2268 kilogram) trailer weight and 500 pound (227 kilogram)tongue weight capacity. If it is necessary to relocate ...

• If you are towing a trailer frequently in hot weather, hilly conditions,at GCWR (or any combination of these factors), consider refillingyour rear axle with synthetic gear lubricant, if not already soequipped. See the Capacities and Specifications chapter for the lubricant specification. • Allow m...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift anddollies or flatbed equipment. Do not tow w...

TOWING THE VEHICLE ON FOUR WHEELS Emergency Towing In the event your vehicle becomes disabled (without access to wheeldollies, car-hauling trailer, or flatbed transport vehicle), it can beflat-towed (all wheels on the ground, regardless of thepowertrain/transmission configuration) under the followin...

To exit four-wheel-down towing and return the transfer case to its 2Hposition:1. With the vehicle still properly secured to the tow vehicle, press and hold the brake pedal. 2. Turn the ignition to the on position; do not start the engine.3. Shift the transmission out of N and into any gear. 4. Relea...

BREAKING-IN You need to break in new tires for approximately 300 mi (480 km).During this time, your vehicle may exhibit some unique drivingcharacteristics. Avoid driving too fast during the first 1000 mi (1600 km).Vary your speed frequently and change up through the gears early. Donot labor the engi...

• Carry unnecessary weight (approximately 1 mpg [0.4 km/L] is lost forevery 400 pounds [180 kilograms] of weight carried). • Add particular accessories to your vehicle (e.g.; bug deflectors,rollbars or light bars, running boards, ski racks). • Drive with the wheels out of alignment. DRIVING THROUGH ...

FLOOR MATS WARNING: Always use floor mats that are designed to fit the footwell of your vehicle. Only use floor mats that leave the pedal area unobstructed. Only use floor mats that are firmly secured toretention posts so that they cannot slip out of position and interferewith the pedals or impair s...

WARNING (Continued) • Failure to properly follow floor mat installation or attachmentinstructions can potentially cause interference with pedal operationcausing loss of control of vehicle. • To install floor mats, position the floor mat so that the eyelet is overthe retention post and press down to ...

• Rear ballast weight behind the rear axle may be required to preventexceeding the FGAWR, and provide front-to-rear weight balance forproper braking and steering. • Front wheel toe may require re-adjustment to prevent prematureuneven tire wear. Specifications are found in the Ford Workshop Manual. •...

Snowplowing with your Air Bag Equipped Vehicle WARNING: Do not attempt to service, repair, or modify the air bag supplemental restraint system (SRS) or its fuses. See your Ford or Lincoln Mercury dealer. WARNING: Additional equipment such as snowplow equipment may effect the performance of the air b...

ROADSIDE ASSISTANCE Vehicles Sold in the U.S. : Getting Roadside Assistance To fully assist you should you have a vehicle concern, Ford Motor Companyoffers a complimentary roadside assistance program. This program isseparate from the New Vehicle Limited Warranty. The service is available: • 24-hours...

If you need to arrange roadside assistance for yourself, Ford MotorCompany will reimburse a reasonable amount for towing to the nearestdealership within 35 miles (56 kilometers). To obtain reimbursementinformation, U.S. Ford vehicle customers call 1-800-241-3673. Customerswill be asked to submit the...

Connecting the Jumper Cables WARNING: Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery. Note: Do not attach the negative (-) cable to fuel lines, engine rocker covers, the intake...

Jump Starting 1. Start the engine of the booster vehicle and run the engine at amoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizeddealer. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfaction. Plea...

• Ford Genuine Accessories • Service specials and promotions. In Canada: Mailing address Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Additional Assistance If you have questions or concerns,...

UTILIZING THE MEDIATION or ARBITRATION PROGRAM(CANADA ONLY) This pertains to vehicles delivered to authorized Canadian dealers. Inthose cases, where you continue to feel that the efforts by Ford ofCanada and the authorized dealer to resolve a factory-related vehicleservice concern have been unsatisf...

CHANGING A FUSE Fuses WARNING: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. If electrical components in the vehicleare not working, a fuse may haveblown. Blown fuses are identifi...

FUSE SPECIFICATION CHART Power Distribution Box WARNING: Always disconnect the battery before servicing high current fuses. WARNING: To reduce risk of electrical shock, always replace the cover to the power distribution box before reconnecting the battery or refilling fluid reservoirs. The power dis...

Fuse/Relay Number Fuse Amp Rating Protected Components 65 20A** Auxiliary power point (instrumentpanel) 66 20A** Auxiliary power point (insidecenter console) 67 20A** Trailer tow park lamps relaypower 68 25A** 4x4 module, 4x2 elocker module 69 30A** Front heated or heated/cooledseats 70 — Not used 7...

To reinstall the fuse box cover, place the top part of the cover on thefuse panel, then push the bottom part of the cover until you hear it clickshut. Gently pull on the cover to make sure it is seated properly. The fuses are coded as follows. Fuse/Relay Number Fuse Amp Rating Protected Components 1...

GENERAL INFORMATION WARNING: Turn off the power running boards, if equipped, before working under the vehicle, jacking or placing any object under the vehicle. Never place your hand between the extendedrunning board and the vehicle. A moving running board may causeinjury. Have your vehicle serviced ...

Working with the Engine On WARNING: To reduce the risk of vehicle damage or personal burn injuries, do not start your engine with the air cleaner removed and do not remove it while the engine is running. 1. Set the parking brake and shift to position P. 2. Block the wheels. OPENING AND CLOSING THE H...

UNDER HOOD OVERVIEW 3.7L V6 Engine A. Windshield washer fluid reservoir B. Battery C. Engine oil dipstick (out of view) D. Brake fluid reservoir E. Engine coolant reservoir F. Air filter assembly G. Engine oil filler cap (out of view) H. Power distribution box A B C D E F G H Maintenance 311 2013 F-...

3.5L V6 EcoBoost 姞 Engine A. Windshield washer fluid reservoir B. Battery C. Engine oil filler cap D. Engine oil dipstick E. Brake fluid reservoir F. Engine coolant reservoir G. Air filter assembly H. Power distribution box A H G C E F D B 314 Maintenance 2013 F-150 (f12) Owners Guide gf, 1st Printi...

ENGINE OIL DIPSTICK A. MIN B. MAX ENGINE OIL CHECK Refer to the scheduled maintenance information for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait 15 minutes for the oil to drain into theoil pan. 3. Set the parkin...

Adding Engine Oil Note: Do not remove the engine oil level dipstick or the filler cap when the engine is running. Note: Do not add engine oil further than the MAX mark. Oil levels above the MAX mark may cause engine damage. Only use oils certified for gasoline engines by theAmerican Petroleum Instit...

Note: For best results, coolant concentration should be tested with a refractometer such as Rotunda tool 300-ROB75240 available from yourdealer. Ford does not recommend the use of hydrometers or coolant teststrips for measuring coolant concentrations. Note: Automotive fluids are not interchangeable;...

• In case of emergency, a large amount of water without engine coolantmay be added in order to reach a vehicle service location. In thisinstance, the cooling system must be drained, chemically cleaned withMotorcraft 威 Premium Cooling System Flush, and refilled with prediluted engine coolant as soon ...

If you drive in extremely hot climates: • It may be necessary to have a Ford authorized dealer decrease thecoolant concentration to 40%. • A coolant concentration of 40% will provide improved overheatprotection. Engine coolant concentrations below 40% will decrease thecorrosion/freeze protection cha...

At this time, you may notice your engine coolant temperature gaugeneedle move toward the H and the POWER REDUCED TO LOWERTEMP message may appear in the information display. You may notice a reduction in the vehicle’s speed caused by reducedengine power. Your vehicle has been designed to enter this m...

AUTOMATIC TRANSMISSION FLUID CHECK Note: Transmission fluid should be checked by an authorized dealer. If required, fluid should be added by an authorized dealer. The automatic transmission does not have a transmission fluid dipstick. Refer to your scheduled maintenance information for scheduled int...

BRAKE FLUID CHECK Fluid levels between the MIN and MAX lines are within the normaloperating range; there is no need to add fluid. If the fluid levels are outsideof the normal operating range, the performance of the system could becompromised; seek service from your authorized dealer immediately. POW...

Washer fluids containing non-methanol antifreeze agents should be usedonly if they provide cold weather protection without damaging thevehicle’s paint finish, wiper blades or washer system. CHANGING THE VEHICLE BATTERY WARNING: Batteries normally produce explosive gases which can cause personal inju...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. Battery Management System (If Equipped) The battery management system (BMS) monitors bat...

CHECKING THE WIPER BLADES Run the tip of your fingers over the edge of the bladeto check for roughness. Clean the wiper blades with washer fluid or waterapplied with a soft sponge or cloth. CHANGING THE WIPER BLADES 1. To remove the wiper blade, pullthe wiper arm away from thevehicle. Pry open the l...

AIR FILTER CHECK WARNING: To reduce the risk of vehicle damage and/or personal burn injuries do not start your engine with the air cleaner removed and do not remove it while the engine is running. When changing the air filter element, use only the air filter elementlisted. Refer to Motorcraft 威 Part...

10. Reconnect the mass air flowsensor electrical connector to theoutlet tube. Make sure the lockingtab on the connector is in the“locked” position (connector shownfrom below for clarity). Changing the Air Filter Element (3.5L EcoBoost Engine) 1. Locate the sensor electrical connector onthe air outle...

9. Replace the air filter housing cover and secure the clamps. Be carefulnot to crimp the filter element edges between the air filter housing andcover and ensure that the tabs on the edge are properly aligned into theslots. 10. Slip the air tube onto the air filter housing and tighten the air-tubecl...

CHANGING A BULB Lamp Assembly Condensation Exterior lamps are vented to accommodate normal changes in pressure.Condensation can be a natural by-product of this design. When moist airenters the lamp assembly through the vents, there is a possibility thatcondensation can occur when the temperature is ...

• Dry the vehicle with a chamois or soft, terry cloth towel in order toeliminate water spotting. • It is especially important to wash the vehicle regularly during thewinter months, as dirt and road salt are difficult to remove and causedamage to the vehicle. • Immediately remove items such as gasoli...

If a staining liquid like coffee or juice has been spilled on the instrumentpanel or on interior trim surfaces, clean as follows: 1. Wipe up spilled liquid using a clean, white, cotton cloth. 2. Wipe the surface with a damp, clean, white, cotton cloth. For morethorough cleaning, use a mild soap and ...

For routine cleaning, wipe the surface with a soft, damp cloth. For morethorough cleaning, wipe the surface with a mild soap and water solution. • Clean spills as quickly as possible. • Test any cleaner or stain remover on an inconspicuous part of theleather as cleaners may darken the leather. • Do ...

• Never apply any cleaning chemical to hot or warm wheel rims orcovers. • Some automatic car washes may cause damage to the finish on yourwheel rims or covers. Industrial-strength (heavy-duty) cleaners, orcleaning chemicals, in combination with brush agitation to removebrake dust and dirt, could wea...

Miscellaneous • Make sure all linkages, cables, levers and pins under vehicle arecovered with grease to prevent rust. • Move vehicles at least 25 ft (8 m) every 15 days to lubricate workingparts and prevent corrosion. Removing Vehicle from Storage When your vehicle is ready to come out of storage, d...

How Your Vehicle Differs from Other Vehicles SUVs, vans and trucks can differfrom some other vehicles in a fewnoticeable ways. Your vehicle maybe: • Higher – to allow higher loadcarrying capacity and to allow itto travel over rough terrainwithout getting hung up ordamaging underbodycomponents. • Sho...

TIRE CARE Information About Uniform Tire Quality Grading Tire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereapplicable on the tire sidewall betweentread shoulder and maximum sectionwidth. For example: • Treadwear 200 Traction AA Temperature A These Tir...

Traction AA A B C WARNING: The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. The traction grades, from highest to lowest are AA, A, B, and C. Thegrades represent the...

INFORMATION CONTAINED ON THE TIRE SIDEWALL Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identifi...

E. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheeldiameter. F. 95: Indicates the tire’s load index. It is an index that relates to how much weight a tire can carry. You may find this information in yourowner...

Information on T Type Tires T type tires have some additionalinformation beyond those of P typetires; these differences aredescribed below. T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Gradesdo not apply to thi...

INFLATING YOUR TIRES Safe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air pressurewithout appearing flat. Every day before you drive, check your tires. If one looks lower than theothers, use a tire gauge to check pressure o...

Damage Periodically inspect the tire treads and sidewalls for damage (such asbulges in the tread or sidewalls, cracks in the tread groove andseparation in the tread or sidewall). If damage is observed or suspected,have the tire inspected by a tire professional. Tires can be damagedduring off-road us...

Tire Replacement Requirements WARNING: Only use replacement tires and wheels that are the same size, load index, speed rating and type (such as P-metric versus LT-metric or all-season versus all-terrain) as those originallyprovided by Ford. The recommended tire and wheel size may be found oneither t...

Important: Remember to replace the wheel valve stems when the road tires are replaced on your vehicle. It is recommended that the two front tires or two rear tires generally bereplaced as a pair. The tire pressure sensors mounted in the wheels (originally installed onyour vehicle) are not designed t...

• Rear-wheel drive (RWD)vehicles/Four-wheel drive (4WD)vehicles (front tires at left ofdiagram) Sometimes irregular tire wear can be corrected by rotating the tires. USING SNOW CHAINS WARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any...

TIRE PRESSURE MONITORING SYSTEM WARNING: The tire pressure monitoring system is NOT a substitute for manually checking tire pressure. The tire pressure should be checked periodically (at least monthly) using a tire gauge.See Inflating Your Tires in this chapter. Failure to properly maintain your tir...

telltale after replacing one or more tires or wheels on your vehicle toensure that the replacement or alternate tires and wheels allow theTPMS to continue to function properly. The tire pressure monitoring system complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is...

To restore the full functionality of the tire pressure monitoring system,have the damaged road wheel/tire repaired and remounted on yourvehicle. For additional information, see Changing tires with a TPMS in this section. When you believe your system is not operating properly The main function of the...

Low tirepressurewarning light Possible cause Customer action required Flashingwarning light Spare tire in use Repair the damaged road wheel/tireand reinstall it on the vehicle torestore system functionality. For adescription on how the systemfunctions, refer to When your temporary spare tire is inst...

TPMS Reset Procedure WARNING: To determine the required pressure(s) for your vehicle, see the Safety Compliance Certification Label (affixed to either the door hinge pillar, door-latch post, or the door edge thatmeets the door-latch post, next to the driver’s seating position), or TireLabel located ...

hinge pillar, door-latch post, or the door edge that meets the door-latchpost, next to the driver’s seating position) or Tire Label located on theB-Pillar or the edge of the driver’s door. See Load Carrying for more information. CHANGING A ROAD WHEEL WARNING: The use of tire sealants may damage your...

The usage of a full-size dissimilar spare tire and wheel assembly can leadto impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability • All-wheel driving...

To remove the jack on Regular Cab and SuperCab models: Remove the wing nut and turn the jack screw counterclockwise torelease pressure before removing the jack from the bracket. To remove the jack on SuperCrew models: 1. Lift both rear seat cushions. 2. Remove the insert containing the Easy Fuel 威 f...

• Rear Jack at the specified locations to avoid damage to the vehicle. 8. Remove the lug nuts with the lug wrench. 9. Replace the flat tire with the spare tire, making sure the valve stem isfacing outward. Reinstall the lug nuts until the wheel is snug against thehub. Do not fully tighten the lug nu...

5. Repeat this tightness check procedure when servicing the spare tirepressure (every six months, as per your scheduled maintenance information), or at any time that the spare tire is disturbed through service of other components. 6. If removed, install the spare tire lock (if equipped) into the bum...

ENGINE SPECIFICATIONS Engine 3.7L V6 Engine 5.0L V8 Engine 6.2L V8 Engine 3.5L V6 EcoBoost Engine Cubic inches 226 302 378 214 Fuel Minimum 87 octane or E85 Minimum 87 octane or E85 Minimum 87 octane Minimum 87 octane Firing order 1-4-2-5-3-6 1-5-4-8-6-3-7-2 1-3-7-2-6-5-4-8 1-4-2-5-3-6 Ignition syst...

Engine Drivebelt Routing 3.7L engine 5.0L engine 6.2L engine 3.5L EcoBoost engine Capacities and Specifications 385 2013 F-150 (f12) Owners Guide gf, 1st PrintingUSA (fus)

VEHICLE IDENTIFICATION NUMBER The vehicle identification number islocated on the driver sideinstrument panel. Please note that in the graphic,XXXX is representative of yourvehicle identification number. The Vehicle Identification Number (VIN) contains the followinginformation: A. World manufacturer ...

ACCESSORIES For a complete listing of the accessories that are available for yourvehicle, please contact your dealer or visit our online store at: Accessories.Ford.com (U.S. only). Ford Custom Accessories are available for your vehicle through yourlocal Ford or Ford of Canada dealer. Ford Motor Comp...

FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY) More than 32 million Ford and Lincoln owners have discovered thepowerful protection of Ford ESP. It is the only extended service planbacked by Ford Motor Company, and provides “peace of mind”protection beyond the New Vehicle Limited Warranty coverage. Up t...

FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY) You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is the only service contractbacked by Ford Motor Company of Canada, Limited. Depending on theplan you purchase, Ford ESP provides benefits such as: • r...

GENERAL MAINTENANCE INFORMATION Why Maintain Your Vehicle? Carefully following the maintenance schedule helps protect against majorrepair expenses resulting from neglect or inadequate maintenance andmay also help to increase the value of your vehicle when you sell ortrade it. Keep all receipts for c...

Protecting Your Investment Maintenance is an investment that pays dividends in the form of improvedreliability, durability and resale value. To maintain the proper performanceof your vehicle and its emission control systems, it is imperative thatscheduled maintenance be completed at the designated i...

additives not approved by Ford Motor Company are not recommended aspart of normal maintenance. Please consult your warranty information. Oils, Fluids and Flushing In many cases, fluid discoloration is a normal operating characteristicand, by itself, does not necessarily indicate a concern or that th...

NORMAL SCHEDULED MAINTENANCE AND LOG Vehicles Equipped with a 3.5L, 3.7L or 5.0L Engine Your vehicle is equipped with an Intelligent Oil-Life Monitor 威 that determines when the engine oil should be changed based on how yourvehicle is used. By using several important factors in its calculations, them...

Normal Scheduled Maintenance * At every oil changeinterval as indicated bythe information display Change engine oil and filter. ** Rotate tires, inspect tire wear and measuretread depth. Perform multi-point inspection(recommended). Inspect automatic transmission fluid level (ifequipped with dipstick...

Additional Maintenance Items 1 Every 30000 miles(48000 km) Replace climate-controlled (heated andcooled) seat filter (if equipped). Replace engine air filter. At 100000 miles(160000 km) Change engine coolant. 2 Every 100000 miles(160000 km) Replace spark plugs. Inspect accessory drive belt(s). 3 Eve...

Maintenance Schedule Log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ...

Extensive Idling or Low-speed Driving for Long Distances as in Heavy Commercial Use (i.e., Delivery, Taxi, Patrol Car or Livery) Inspect frequently,service as required Replace engine air filter. Every 5000 miles(8000 km) Inspect brake system. Inspect wheels and related components forabnormal noise, ...

Off-road Operation Inspect frequently,service as required Inspect steering linkage, ball joints andU-joints. Lubricate if equipped with greasefittings. Replace engine air filter. Every 5000 miles(8000 km) Change engine oil and filter. * Inspect the wheels and related components forabnormal noise, we...

Special Operating Condition Log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D A...

EXCEPTIONS Normal vehicle axle maintenance: Rear axles and power take-off (PTO) units with synthetic fluid and light-duty trucks equipped withFord-design axles are lubricated for life; do not check or change fluidunless a leak is suspected, service is required or the assembly has beensubmerged in wa...

ENGINE COOLANT CHANGE RECORD 3.5L, 3.7L and 5.0L Engines Initial change Six years or 100000 miles (160000 km)(whichever comes first) After initial change Every three years or 50000 miles (80000 km) 6.2L Engine Initial change Six years or 105000 miles (168000 km)(whichever comes first) After initial ...

GENERAL INFORMATION Ensure that you review your device’s user guide before using it withSYNC. Support The SYNC support team is available to help you with any questions youcannot answer on your own. Monday-Saturday, 8:30am-8:00pm EST In the United States, call: 1–888–270–1055 In Canada, call: 1–800–5...

When using SYNC, do not: • Operate playing devices if the power cords or cables are broken, splitor damaged. Carefully place cords and cables where they cannot bestepped on or interfere with the operation of pedals, seats,compartments or safe driving abilities. • Leave playing devices in the vehicle...

Phone Options during an Active Call During an active call, you have additional menu features which becomeavailable such as putting a call on hold, joining calls, etc. Use the arrowbuttons to scroll through the menu options. To access:1. Press MENU during an active call.2. When Active Call Menu is se...

When you select: You can: Call History Access your call history log.1. Press OK to select, then scroll through your callhistory options (incoming, outgoing or missed).2. Press OK when the desired selection appears in thedisplay.3. Press the phone button to call the selection. Return Exit the current...

When you select: You can: Phonebook 1,2 Allows you to access your downloaded phonebook.1. Press OK to confirm and enter. If your phonebook hasfewer than 255 listings, they appear alphabetically in flatfile mode. If there are more, they are organized intoalphabetical categories.2. Scroll until the de...

Text Messaging Note: This is a phone-dependent feature. SYNC allows you to receive, send, download and delete text messages.The system can also read incoming text messages to you so that you donot have to take your eyes off the road. Receiving a Text Message Note: This is a phone-dependent feature. ...

Download Unread Msgs allows you to download your unread messages (only) to SYNC. To download the messages, press OK to select. Thedisplay indicates your messages are being downloaded. When complete,SYNC takes you to your inbox. Delete All Messages? allows you to delete current text messages from SYN...

Pre-defined text message options I need more directions I love you Too funny Can’t wait to see you I’m stuck in traffic Accessing Your Phone Settings These are phone-dependent features. Your phone settings allow you toaccess and adjust features such as your ring tone, text messagenotification, modif...

When you select: You can: Modify Phonebook Modify the contents of your phone book (i.e.,add, delete, download). Press OK to selectand scroll between: Add Contacts: Press OK to add more contactsfrom your phone book. Push the desiredcontact(s) on your phone. See your phone’suser guide on how to push c...

System Settings System Settings provide access to your Bluetooth Devices andAdvanced menu features. Use the arrow buttons to scroll through themenu options. The Bluetooth Devices menu allows you to add, connect, delete and set aphone as primary as well as turn your Bluetooth feature on and off. The ...

If you select: You can: Delete Device Delete a paired phone.Press OK and scroll to select the device. Press OK toconfirm. Delete AllDevices Delete all previously paired phones (and allinformation originally saved with those phones).Press OK to select. Return Exit the current menu. * This is a speed-...

If you select: You can: FactoryDefaults Return to the factory default settings. This selectiondoes not erase your indexed information (phonebook,call history, text messages and paired devices).1. Press OK to select and then press OK again whenRestore Defaults? appears in the display.2. Press OK to c...

If the call is not cancelled and a successful call is made, a pre-recordedmessage is played for the 911 operator, then the occupant(s) in thevehicle is able to talk with the operator. Be prepared to provide yourname, phone number and location immediately, because not all 911systems are capable of re...

Note: In order to allow a break-in period for your vehicle, you may not be able to create a Vehicle Health Report until your vehicle odometer hasreached 200 miles. Register for Vehicle Health Report and set your report preferences atwww.SYNCMyRide.com. After registering, you can request a VehicleHea...

Vehicle Health Report Options Run Report? Press OK for SYNC to run a health report ofyour vehicle’s diagnostic systems and send theresults to Ford where it is combined withscheduled maintenance information, openrecalls and other field service actions andunserviced vehicle inspection items from youra...

Receiving Turn-by-Turn Directions 1. When connected to SYNC Services, say “Directions” or “Business search”. To find the closest business or type of business to yourcurrent location, just say “Business search” and then “Search nearme”. If you need further assistance in finding a location you can say...

“USB” “Search song <name>” 1 “Search track <name>” 1,3 “Shuffle off” “Shuffle on” “Similar music” “What’s playing?” 1 “<name>” is a dynamic listing, meaning that it could be the name of any desired group, artist, etc. 2 Voice commands which are only available in folder mode. 3 Voic...

Voice Command Guide “Refine” This allows you to make your previouscommand more specific. For example, if youasked to search and play all music by acertain artist, you could then say “refinealbum” and choose a specific album from thelist to view. If you then select Play, the systemonly plays music fr...

When you select: You can: Select Source SYNC USB: Press OK to access music plugged into your USB port. You can also plugin devices to charge them (if supported byyour device). Once connected, the systemindexes any readable media files. (The timerequired to complete this depends on the sizeof the med...

Accessing Your Play Menu This menu allows you to select and play your media by artist, album,genre, playlist, track, similar music or even to explore what is on yourUSB device.1. Make sure that your device is plugged into the USB port and is turned on. 2. Press AUX and then MENU to enter the Media M...

When you select: You can: Similar Music Play music similar to what is currently playingfrom the USB port. The system uses themetadata information of each song to compilea playlist for you.Press OK to select. The system creates a newlist of similar songs and begins playing. Themetadata tags must be p...

4. Press OK and then scroll to select from: When you select: You can: Add BluetoothDevice * Allows you to pair additional devices to thesystem.1. Press OK to select and press OK againwhen Find SYNC appears in the display.2. Follow the directions in your phone’s userguide to put your phone into disco...

Advanced Menu Options This menu allows you to access settings such as prompts, language,performing a master reset as well as returning to factory defaults.1. Press AUX and then MENU to access the Media Menu.2. Scroll until System Settings appears and select OK.3. Scroll until Advanced appears.4. Pre...

When you select: You can: Master Reset Completely erase all information stored onSYNC (all phonebook, call history, textmessages and all paired devices) and returnto the factory default settings. Application Download new software applications (ifavailable) and then load the desiredapplications throu...

Vehicle Health Report/Services (Traffic, Directions and Information) Issues Issue Possible Cause(s) Possible Solution(s) I received a textthat the VehicleHealth Report isnot activated. • Your account may not beactivated on thewebsite, OR • You may have the wrong VIN(vehicleidentificationnumber) list...

INTRODUCTION WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that maytake their focus off the road. Your primary responsibility is the safeoperation of the vehicle...

HOME Press to access your home screen. Depending on your vehicle’soption package and software, your screens may vary in appearance from the screens shown in this section. Your features mayalso be limited depending on your market. Check with your authorizeddealer for availability. Using the Touch-sen...

How to Use Voice Commands with Your System Press the voice icon; after the tone, speak your commandclearly. These commands can be said at any time. “Cancel” “Exit” “Go back” “List of commands” “Main menu” “Next page” “Previous page” “What can I say?” “Help” What Can I Say To access the available voi...

Voice Command List “Navigation list of commands” * “Phone list of commands” “Radio list of commands” “SD card list of commands” “Sirius satellite list of commands” * “Travel link list of commands” * “USB list of commands” “Voice instructions list of commands” “Voice settings list of commands” “Help”...

Phone/Media Candidate Lists: Candidate lists are lists of possible results from your voice commands. The system creates these lists whenit has the same confidence level of several options based on your voicecommand. To access these settings using the touchscreen:1. Press the Settings icon > Setti...

ENTERTAINMENT Your system offers many media options. You can access these optionsusing the touchscreen or voice commands. Browsing Device Content When listening to any type of audio, you can browse through otherdevices without having to change sources. For example, if you arecurrently listening to t...

AM/FM Radio Press the lower left corner of the touchscreen and then selectthe AM or FM tab. To change between AM and FM presets, just touch the AM or FM tab. When you select: You can: Presets Save a station by pressing and holding one ofthe memory preset areas. There is a briefmute while the station...

HD Radio Reception and Station Troubleshooting Potential Reception Issues Reception area If you are listening to a multicast station andyou are on the fringe of the reception area,the station may mute due to weak signalstrength.If you are listening to HD1, the systemswitches back to the analog broad...

Radio Voice Commands If you are listening to the radio, press the voice button on thesteering wheel control. When prompted, say any of thecommands in the following chart. If you are not listening to the radio, press the voice button and, after thetone, say “Radio”, then any of the commands in the fo...

“TUNE” “FM” “Preset <#>” “FM <87.9–107.9>” “Help” “FM <87.9-107.9> HD <#>” * * If available. SIRIUS 姞 Satellite Radio (If Activated) Press the lower left corner of the touchscreen, then select theSIRIUS tab. When you select: You can: Presets Save a station by pressing and hol...

Satellite Radio Voice Commands If you are listening to SIRIUS satellite radio, press the voicebutton on the steering wheel control. When prompted, say anyof the commands in the following chart. If you are not listening to SIRIUS satellite radio, press the voice buttonand, after the tone, say “Sirius...

“TUNE” “SAT 3” “SAT 3 preset <#>” “Help” SIRIUS Satellite Radio Information Note: SIRIUS reserves the unrestricted right to change, rearrange, add or delete programming including canceling, moving or adding particularchannels, and its prices, at any time, with or without notice to you. FordMot...

Potential Satellite Radio Reception Issues Station overload When you pass a ground-based broadcastrepeating tower, a stronger signal mayovertake a weaker one and the audio systemmay mute. Satellite radio signalinterference Your display may show ACQUIRING . . . toindicate the interference and the aud...

SIRIUS Troubleshooting Tips Radio Display Condition Possible Action Call SIRIUS1–888–539–7474. Satellite service hasbeen deactivated bySIRIUS Satellite Radio. Call SIRIUS at1–888–539–7474 toreactivate or resolvesubscription issues. No Channels Available. All the channels in the selected category are...

CD Voice Commands If you are listening to a CD, press the voice button on thesteering wheel control. When prompted, say any of thecommands in the following chart. If you are not listening to a CD, press the voice button and, after thetone, say “CD”, then any of the commands in the following chart. “...

USB Port The ports are located either in the centerconsole or behind a small access door in theinstrument panel. To access and play musicfrom your device, press the lower left cornerof the touchscreen. This feature allows you to plug in media playing devices, memory sticks,flash drives, thumb drives...

“BROWSE” “All songs” “Video playlist <name>” * “All TV shows” * “Video podcast <name>” * “All video playlists” * “Help” * These commands are only available in USB mode and are device-dependent. Bluetooth Audio Your system allows you to stream audio over your vehicle’s speakers fromyour c...

3. Press the lower left corner on the touchscreen. Select either a tuned station from the FM tab or the CD tab (if there is a CD alreadyloaded into the system). Adjust the volume to a comfortable listeninglevel. 4. Turn the portable music player on and adjust the volume to 1 ⁄ 2 the maximum. 5. Pres...

Phone Menu Options Press the top left corner on your touchscreen to select from thefollowing options: When you select: You can: Phone Access the on-screen numerical pad to entera number and place a call.During an active call, you can also choose tomute the call, put it on hold, activate privacy(retu...

When you select: You can: Messaging Send text messages using your touchscreen.See Text messaging later in this section. Settings Access various phone settings, such turningBluetooth on and off, managing yourphonebook and more. See Phone settings later in this section. Text Messaging Note: Downloadin...

Pre-defined Text Message Options I’ll call you back in a few minutes. I just left, I’ll be there soon. Can you give me a call? I’m on my way. I’m running a few minutes late. I’m ahead of schedule, so I’ll be there early. I’m outside. I’ll call you when I get there. OK Yes No Thanks Stuck in traffic....

If you select: You can: Do Not Disturb Have all calls go directly to your voice mailand not ring in the vehicle. With this featureturned on, text message notifications are alsosuppressed and do not ring inside the vehicle. 911 Assist Turn 911 Assist 威 on or off. See 911 Assist 威 in the SYNC Services...

SYNC Services Quick Tips Portable Your subscription is associated with yourBluetooth-enabled cellular phone number, notyour VIN (Vehicle Identification Number). Youcan pair and connect your phone to anyvehicle equipped with Traffic, Directions andInformation and continue enjoying yourpersonalized se...

SIRIUS Travel Link Voice Commands Note: In order to use SIRIUS Travel Link, your vehicle must be equipped with navigation and your navigation SD card must be in the SD card slot. Press the voice button and when prompted, say any of thefollowing: Travel Link Voice Commands “5–day weather forecast” “S...

Uploading Photos for Your Home Screen Wallpaper Note: You cannot load photos directly from your camera. You must access the photos from either your USB mass storage device or from anSD card. Note: Photographs with extremely large dimensions (i.e., 2048 x 1536) may not be compatible and appear as a b...

Ambient Lighting (If Equipped) When activated, ambient lighting illuminates footwells and cupholderswith a choice of colors. To access and make adjustments:1. Press the Settings icon > Vehicle > Ambient Lighting.2. Touch the desired color.3. Use the scroll bar to increase or decrease the inten...

Settings Access and adjust system settings, voice features, as well as phone,navigation and wireless settings. Some of these settings can also beaccessed with regard to their specific modes (i.e., phone and media). System Press the Settings icon > Settings > System, then select from thefollowi...

Voice Control Press the Settings icon > Settings > Voice Control, then select from thefollowing: Voice Control Interaction Mode Standard interaction mode provides moredetailed interaction and guidance. Advancedmode has less audible interaction and moretone prompts. ConfirmationPrompts Have the...

Media Player Press the Settings icon > Settings > Media Player, then select from thefollowing: Media Player Autoplay With this feature on, the system automaticallyswitches to the media source upon initialconnection and you can listen to music whichhas already been randomly indexed duringthe in...

Navigation Press the Settings icon > Settings > Navigation, then select from thefollowing: Navigation Map Preferences Turn breadcrumbs on and off. Have the system display your turn list top tobottom or bottom to top. Turn the Parking POI notification on and off. Route Preferences Have the syst...

Wireless & Internet Your system has a Wi-Fi feature which creates a wireless network withinyour vehicle, thereby allowing other devices (i.e., personal computers orphones) in your vehicle to speak to each other, share files, play games,etc. Using this Wi-Fi feature, everyone in your vehicle can ...

Wireless & Internet USB MobileBroadband Instead of using Wi-Fi, your system can alsouse a USB mobile broadband connection toaccess the internet. (You must activate yourmobile broadband device on your PC prior toconnecting it to the system.) This screenallows you to set up what is your typical ar...

Help Press the Settings icon > Help, then select from the following: Help Where Am I? View the vehicle’s current location, if yourvehicle is equipped with navigation. If yourvehicle is not equipped with navigation,nothing is displayed. System Information View the following information: Touchscree...

CLIMATE CONTROLS Depending on your vehicle line and option package, your climate screenmay look different than what is shown here. A. Power: Touch to turn the system on and off. Outside air cannot enter the vehicle when the system is off. B. Passenger settings: • Touch DUAL to turn on the passenger ...

Additional Climate Control Voice Commands “On” “Windshield floor on” “Panel floor on” “Help” * If you have said “Temperature”, you can say any of the commands in the following “Temperature” chart. “TEMPERATURE” “High” “Low” “<15.5–29.5> degrees” “<60–85> degrees” “Help” NAVIGATION SYSTEM...

Destination Selections Emergency Edit Route Cancel Route Previous Starting Point Freeway Entrance/Exit Latitude/Longitude 1. Enter the necessary information into the highlighted text fields (in any order). For address destination entry, the Go! button appearsonce all the necessary information has be...

This icon appears when your selection exists in multiplecategories within the system. When you are viewing additional information for hotels, cityseekr alsotells you if the hotel has certain services and facilities using icons: Hotel Services and Facilities Restaurant 24 Hr Room Service Business Cen...

Setting Your Navigation Preferences Select settings for the system to take into account when planning yourroute. Press the Settings icon > Settings > Navigation. When you select: You can: Map Preferences Turn breadcrumbs on and off. Have the system display your turn list top tobottom or bottom...

When you select: You can: Traffic Preferences Choose how you want the system to handletraffic problems along your route.Automatic: Have the system reroute you toavoid traffic incidents that develop andimpact the current route (no notification isprovided).Manual: Have the system always provide atraff...

Change the appearance of the mapdisplay by repeatedly pressing thearrow button in the upper leftcorner of the screen. It togglesbetween three different map modes;Heading up, North up, and 3D. Heading up (2D map) always shows the direction of forward travel to be upward on the screen. This view is av...

Map Icons Vehicle mark shows the current location of the vehicle. It stays in the center of the map display, except when in scroll mode. Scroll cursor allows you to scroll the map; the icon is fixed in the center of the screen. The map position closest to the cursoris in a window on the top center p...

“DESTINATION” “<nametag>” “<POI category>” “Favorites” “Home” “Intersection” “Nearest <POI category>” “Nearest POI” “Play nametags” “POI category” “Previous destination” “Street address” “Help” “NAVIGATION” “Destination” * “Zoom city” “Zoom country” “Zoom in minimum” “Zoom out maxi...

GENERAL INFORMATION SYNC 姞 End User License Agreement (EULA) • You have acquired a device (“DEVICE”) that includes software licensed by FORD MOTOR COMPANY from an affiliate of MicrosoftCorporation (“MS”). Those installed software products of MS origin, aswell as associated media, printed materials, ...

SOFTWARE’s ability to use WMDRM to play or copy protectedcontent. This action does not affect unprotected content. When yourDEVICE downloads licenses for protected content, you agree thatMicrosoft may include a revocation list with the licenses. Contentowners may require you to upgrade the SOFTWARE ...

property rights in and to the content which may be accessed through useof the SOFTWARE is the property of the respective content owner andmay be protected by applicable copyright or other intellectual propertylaws and treaties. This EULA grants you no rights to use such content.All rights not specif...

End user notice Microsoft 姞 Windows 姞 Mobile for Automotive Important Safety Information This system Ford SYNC™ contains software that is licensed toManufacturer FORD MOTOR COMPANY by an affiliate of MicrosoftCorporation pursuant to a license agreement. Any removal, reproduction,reverse engineering ...

Software. TeleNav also does not warrant the accuracy of the map orother data used for the TeleNav Software. Such data may not alwaysreflect reality due to, among other things, road closures, construction,weather, new roads and other changing conditions. You are responsiblefor the entire risk arising...

8.3 By using the TeleNav Software, you consent to receive from TeleNavall communications, including notices, agreements, legally requireddisclosures or other information in connection with the TeleNav Software(collectively, “Notices”) electronically. TeleNav may provide such Noticesby posting them o...

SAVINGS, OR ANY OTHER DIRECT, INDIRECT, INCIDENTAL, SPECIALOR CONSEQUENTIAL DAMAGES ARISING OUT OF YOUR USE OF ORINABILITY TO USE THIS DATA, ANY DEFECT IN THIS DATA, OR THEBREACH OF THESE TERMS OR CONDITIONS, WHETHER IN ANACTION IN CONTRACT OR TORT OR BASED ON A WARRANTY, EVENIF NT OR ITS LICENSORS ...

furnished shall be marked and embedded as appropriate with thefollowing “Notice of Use”, and be treated in accordance with such Notice: NOTICE OF USE CONTRACTOR (MANUFACTURER/ SUPPLIER) NAME: NAVTEQ CONTRACTOR (MANUFACTURER/SUPPLIER) ADDRESS: 425 West Randolph Street, Chicago, IL 60606. This Data is...

911 Assist™ ......................442, 515 A ABS (see Brakes) .....................227 Accessing and using yourUSB port ....................................494 Accessing call history/phonebook during active call .............432 Accessing your calendar ..........514 Accessing your media menufeatures...