Ford 2013 Expedition v.1- User Manual

ABOUT THIS MANUAL Thank you for choosing Ford. We recommend that you take some time toget to know your vehicle by reading this manual. The more that youknow about it, the greater the safety and pleasure you will get fromdriving it. WARNING: Always drive with due care and attention when using and ope...

SYMBOL GLOSSARY WARNING: You risk death or serious injury to yourself and others if you do not follow the instruction highlighted by the warning symbol. These are some of the symbols you may see on your vehicle. Symbol Description Symbol Description Symbol Description Safety alert See Owner’sManual ...

Symbol Description Symbol Description Symbol Description Heated rearwindow Interiorluggagecompartmentrelease Jack Lightingcontrol Low tirepressurewarning Maintaincorrect fluidlevel Panic alarm Parking aidsystem Parking brakesystem Powersteering fluid Powerwindowsfront and rear Powerwindowlockout Ser...

Note: Including to the extent that any law pertaining to Event DataRecorders applies to SYNC 威 or its features, please note the following: Once 911 Assist (if equipped) is enabled (set ON), 911Assist may, through any paired and connected cell phone, discloseto emergency services that the vehicle has...

FORD CREDIT (U.S. ONLY) Ford Credit offers a full range of financing and lease plans to help youacquire your vehicle. If you have financed or leased your vehicle throughFord Credit, thank you for your business. For your convenience we offer a number of ways to contact us, as wellas help manage your ...

SPECIAL NOTICES New Vehicle Limited Warranty For a detailed description of what is covered and what is not covered byyour vehicle’s New Vehicle Limited Warranty, see the warrantyinformation that is provided to you along with your owner’s manual. Special Instructions For your added safety, your vehic...

MOBILE COMMUNICATIONS EQUIPMENT Using mobile communications equipment is becoming increasinglyimportant in the conduct of business and personal affairs. However, youmust not compromise your own or others’ safety when using suchequipment. Mobile communications can enhance personal safety andsecurity ...

GENERAL INFORMATION See the following sections for directions on how to properly use safetyrestraints for children. WARNING: Always make sure your child is secured properly in a device that is appropriate for their height, age and weight. Child safety restraints must be bought separately from your v...

WARNING: Always restrain an unoccupied child seat or booster seat. These objects may become projectiles in a collision or sudden stop, which may increase the risk of serious injury. WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it r...

BOOSTER SEATS WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the riskof injury or death in a collision. Use a belt-positioning booster seat for children who ha...

Types of Booster Seats • Backless booster seats If your backless booster seat has a removable shield, remove the shield.If a vehicle seating position has a low seat back or no head restraint, abackless booster seat may place your child’s head (as measured at thetops of the ears) above the top of the...

Perform the following steps when installing the child seat withcombination lap/shoulder belts: Note: Although the child seat illustrated is a forward facing child seat, the steps are the same for installing a rear facing child seat. 1. Position the child safety seat in aseat with a combination lap a...

4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear a snap and feel the latchengage. Make sure the tongue islatched securely by pulling on it. 5. To put the retractor in theautomatic locking mode, grasp...

This is necessary to remove the remaining slack that will exist once theextra weight of the child is added to the child restraint. It also helps toachieve the proper snugness of the child seat to your vehicle.Sometimes, a slight lean toward the buckle will additionally help toremove remaining slack ...

Follow the instructions on attaching child safety seats with tether straps.See Using Tether Straps in this chapter. Attach LATCH lower attachments of the child seat only to the anchorsshown. Each time you use the safety seat, check that the seat is properlyattached to the lower anchors and tether an...

The tether strap anchors in your vehicle are in the following positions(shown from top view): • Second row bench seat • Second row bucket seats Attach the tether strap only to the appropriate tether anchor as shown.The tether strap may not work properly if attached somewhere otherthan the correct te...

2. Locate the correct anchor for the selected seating position. • Second row outboard seatingpositions • Second row center seatingposition (if equipped) 3. Grasp the tether strap andposition it to the seat frame. 4. Rotate the tether strap, and clipthe tether strap to the anchor onthe seat frame. Ch...

5. Rotate the tether strap clip. 6. Tighten the child safety seat tether strap according to themanufacturer’s instructions. Third row center seating position 1. Route the child safety seat tether strap over the back of the seat. 2. Locate the anchor webbing loop for the seating position. • You may n...

3. Clip the tether strap through the anchor loop as shown. If the tetherstrap is clipped incorrectly, the child safety seat may not be retainedproperly in the event of a collision. 4. Tighten the child safety seattether strap according to themanufacturer’s instructions. If thesafety seat is not anch...

PRINCIPLES OF OPERATION WARNING: Always drive and ride with your seat back upright and the lap belt snug and low across the hips. WARNING: To reduce the risk of injury, make sure children sit where they can be properly restrained. WARNING: Never let a passenger hold a child on his or her lap while t...

FASTENING THE SAFETY BELTS The front outboard and rear safety restraints in the vehicle arecombination lap and shoulder belts. 1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until you hear a snap and feelit latch. Make sure the tongue is...

Pregnant women should alwayswear their safety belts. The lap beltportion of a combination lap andshoulder belt should be positionedlow across the hips below the bellyand worn as tight as comfort willallow. The shoulder belt should bepositioned to cross the middle ofthe shoulder and the center of the...

Automatic Locking Mode In this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to remove any slack in the shoulder belt. The automaticlocking mode is not available on the driver safety belt. When to Use the Automatic Locking Mode This mode should be used any time a ch...

SAFETY BELT HEIGHT ADJUSTMENT WARNING: Position the safety belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat beltand increase the risk of injury in a collision. Adjust the height of t...

To adjust the comfort guide: 1. Slip the shoulder belt into the beltguide (the portion of the belt betweenthe latch tongue and the D-ring, notthe portion where the belt exits fromthe quarter trim panel). 2. Slide the guide up or down alongthe webbing so that the belt iscentered on the occupant’sshou...

• all vehicle doors are closed. • the driver’s safety belt is unbuckled. 1. Switch the ignition on. DO NOT START THE ENGINE. 2. Wait until the safety belt warning light turns off (approximately1–2 minutes). • Steps 3 and 4 must be completed within 60 seconds or the procedurewill have to be repeated....

The airbags are a supplemental restraint system and are designed towork with the safety belts to help protect the driver and right frontpassenger from certain upper body injuries. Airbags DO NOT inflateslowly; there is a risk of injury from a deploying airbag. Note: You will hear a loud bang and see...

• Restraint system warning light and backup tone. • The electrical wiring for the airbags, crash sensor(s), safety beltpretensioners, front safety belt usage sensors, driver seat positionsensor, and indicator lights. How does the Restraint Safety System work? The Restraint Safety System can adapt th...

The driver and front passengerairbags will deploy during significantfrontal and near frontal collisions. The driver and passenger front airbag system consists of: • Driver and passenger airbag modules • Crash sensors and monitoring system with readinessindicator. See Crash Sensors and Airbag Indicat...

WARNING: If the side airbag has deployed, the airbag will not function again. The side airbag system (including the seat) must be inspected and serviced by an authorized dealer. If the airbag is not replaced, the unrepaired area will increase the risk ofinjury in a collision. The side airbags are fi...

• A flexible headliner which opens above the side doors to allow aircurtain deployment. • Crash sensors and monitoring system with readinessindicator. See Crash Sensors and Airbag Indicator in this chapter. Children 12 years old and under should always be properly restrained inthe rear seats. The Sa...

A difficulty with the system is indicated by one or more of the following: • The readiness light will either flash or stay lit. • The readiness light will not illuminate immediately after theignition is turned on. • A series of five beeps will be heard. The tone pattern will repeatperiodically until...

GENERAL INFORMATION ON RADIO FREQUENCIES This device complies with part 15 of the FCC Rules and with IndustryCanada license-exempt RSS standard(s). Operation is subject to thefollowing two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference...

REMOTE CONTROL Integrated Keyhead Transmitters Your vehicle may be equipped withtwo integrated keyheadtransmitters. The key blade is usedto start the vehicle and unlock orlock the driver’s door from outsidethe vehicle. The transmitter portionfunctions as the remote control. Note: Your vehicle’s keys...

Car Finder Press the button twice within three seconds. The horn willchirp and the turn signals will flash. It is recommended thatthis method be used to locate your vehicle, rather than using the panic alarm. Sounding a Panic Alarm Note: The panic alarm will only operate when the ignition is off. Pr...

PRINCIPLES OF OPERATION MyKey 威 allows you to program keys with restricted driving modes to promote good driving habits. All but one of the keys programmed to thevehicle can be activated with these restricted modes. Any keys that havenot been programmed are referred to as an administrator key or adm...

• Audio system maximum volume of 45%. A message in the audiosystem is displayed when attempting to exceed the limited volume. • AdvanceTrac. The system cannot be turned off when Always-on hasbeen set. CREATING A MYKEY Use the information display controls to create a MyKey.1. Insert the key you want ...

In addition to the key that has been programmed as a MyKey, owners ofvehicles equipped with traditional keys have the option to program thenon-Ford-approved remote start system as a MyKey if the remote startfob is used by the MyKey driver. To program a non-Ford-approved remote start system as a MyKe...

LOCKING AND UNLOCKING You can use the power door lock control or the remote control to lockand unlock the vehicle. Power Door Locks The power door lock control is located on the driver and front passengerdoor panels. A. Unlock B. Lock Remote Control The remote control can be used anytime the vehicle...

Power Liftgate or Liftgate Window (If Equipped) WARNING: Make sure all persons are clear of the power liftgate area before using the control. WARNING: Make sure the power liftgate is closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from f...

Autolock and Unlock The autolock feature will lock all the doors, the liftgate and the liftgatewindow when: • all doors are closed, • the ignition is on, • you shift into any gear putting the vehicle in motion, and • the vehicle attains a speed greater than 12 mph (20 km/h). If the vehicle was autol...

Power Liftgate (If Equipped) WARNING: Make sure that the liftgate is closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out. If you must drive withthe liftgate door open, keep the vehicle well ventilated so outside aircomes int...

If the liftgate reverses and starts to close after a open request, a fastcontinuous chime indicates excessive load on the liftgate or a possiblestrut failure. If any excessive load is removed and you still have a fasterchime, have the system serviced immediately by your authorized dealer. Do not att...

To close with the rear cargo area button: WARNING: Keep clear of the liftgate when activating the rear switch. Note: The rear cargo area control button is disabled when the liftgate is latched. Press and release the control on theleft rear quarter panel. A chime willbeep once if conditions are notco...

Resetting the Power Liftgate If any of these conditions occur, the power liftgate may not operate andmust be reset: • A low voltage or dead battery • Disconnected battery • The liftgate is manually closed and left ajar (unlatched) To reset the power liftgate: 1. Disconnect the battery for 20 seconds...

SECURICODE™ KEYLESS ENTRY KEYPAD You can use the keyless entrykeypad to lock or unlock the doorsor release the liftgate glass withoutusing a key. The keypad can be operated with the factory set 5-digit entry code; this code is located on the owner’swallet card in the glove box and is available from ...

Replacement Keys Note: Your vehicle may come equipped with two integrated keyhead transmitters. The integrated keyhead transmitter functions as a programmed ignitionkey that operates all the locks and starts the vehicle, as well as a remotecontrol. If your programmed transmitters or standard SecuriL...

6. Turn the ignition off and remove the second previously programmedcoded key from the ignition. 7. After three seconds but within 20 seconds of turning the ignition offand removing the previously programmed coded key, insert the newunprogrammed key into the ignition. 8. Turn the ignition from off t...

Disarming the Alarm To disarm the alarm, do any of the following: • Press the power door unlock button within the 20-second pre-armedmode. • Press the unlock button on the remote control. • Unlock the doors with the keyless entry pad. • Turn the ignition on with a valid key. • Press the panic button...

ADJUSTING THE STEERING WHEEL WARNING: Do not adjust the steering wheel when your vehicle is moving. 1. Pull and hold the steering wheelrelease lever. 2. Adjust the steering wheel to thedesired position then release thelever. AUDIO CONTROL A. Media B. Volume up C. Volume down D. Seek down or previous...

VOICE CONTROL (IF EQUIPPED) A. Voice recognition B. Phone mode Press OK to confirm selection. See the SYNC or Navigation System chapter. CRUISE CONTROL See the Cruise Control chapter. B A + SET RES OFF ON 78 Steering Wheel 2013 Expedition (exd) Owners Guide gf, 1st PrintingUSA (fus)

ADJUSTABLE PEDALS (IF EQUIPPED) WARNING: Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving. The control is located on the left side of the steering column. Press andhold the appropriate control to move the pedals. A. Farther B. Closer The pedal position...

WINDSHIELD WIPERS Note: Fully defrost the windshield before turning on the windshield wipers. Note: Make sure the windshield wipers are turned off before entering a car wash. Note: Clean the windshield and wiper blades if they begin to leave streaks or smears. If that does not resolve the issue, ins...

LIGHTING CONTROL Rotate the control clockwise to thefirst position to turn on the parkinglamps. Rotate the control clockwise to thesecond position to turn on theheadlamps. Rotate the control to the verticalposition to turn the headlamps off. High Beams • Push the lever toward theinstrument panel to ...

AUTOLAMPS The autolamp system provides lightsensitive automatic on/off control ofthe exterior lights normallycontrolled by the headlamp control. The autolamp system also keeps thelights on for approximately20 seconds or, if equipped with amessage center, you can select adelay from 0–180 seconds afte...

DAYTIME RUNNING LAMPS (IF EQUIPPED) WARNING: Always remember to switch your headlamps on in low light situations or during inclement weather. The system does not activate the tail lamps and may not provide adequate lightingduring these conditions. Failure to activate your headlamps under thesecondit...

INTERIOR LAMPS Front Row Map Lamps (If Equipped) To turn on the map lamps, press theouter edge of the clear lens. Thefront row map lamp lights when: • any door is opened. • the instrument panel dimmerswitch is rotated until the courtesylamps come on. • the remote entry controls are pressed and the i...

Rear Cargo Lamp The rear cargo lamp lights when: • any door is opened, and theswitch is in the middle position. • the instrument panel dimmerswitch is rotated until thecourtesy lamps come on. • any of the remote entry controlsare pressed and ignition is off(and switch is in the middleposition). With...

POWER WINDOWS WARNING: Do not leave children unattended in the vehicle and do not let them play with the power windows. They may seriously injure themselves. WARNING: When closing the power windows, you should verify they are free of obstructions and make sure that children and pets are not in the p...

Window Lock A. Unlock B. Lock Press the control to lock or unlock the rear and front passenger windowcontrols. Accessory Delay You can use the window switches for several minutes after you switchthe ignition off, or until either front door is opened. EXTERIOR MIRRORS Power Exterior Mirrors WARNING: ...

Fold-Away Exterior Mirrors Push the mirror toward the door window glass. Make sure that you fullyengage the mirror in its support when returning it to its original position. Power-Folding Mirrors (If Equipped) Note: Activating the mirrors 10 or more times within one minute, or repeated folding and u...

Integrated Blind Spot Mirrors WARNING: Objects in the blind spot mirror are closer than they appear. Blind spot mirrors have an integrated convex mirror built into the upperoutboard corner of the exterior mirrors. They are designed to assist youby increasing visibility along the side of your vehicle...

INTERIOR MIRROR WARNING: Do not adjust the mirror when your vehicle is moving. Note: Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum or ammonia based cleaning products. You can adjust the interior mirror to your preference. Some mirrors alsohave a second...

GAUGES Cluster shown in standard measure. Metric similar. A. Tachometer B. Battery voltage gauge: C. Engine oil pressure gauge D. Speedometer E. Fuel gauge F. Information display. See Information displays for more information. G. Engine coolant temperature gauge Battery Voltage Gauge Indicates the b...

Fuel Gauge Indicates approximately how much fuel is left in the fuel tank (when theignition is on). The fuel gauge may vary slightly when the vehicle is inmotion or on a grade. The fuel icon and arrow indicates which side ofthe vehicle the fuel filler door is located. Information Display Odometer Lo...

Anti-Lock Braking System If it illuminates when you are driving, this indicates amalfunction. You will continue to have the normal brakingsystem (without ABS) unless the brake warning lamp is also illuminated. Have the system checked by your authorized dealer. Battery If it illuminates while driving...

Low Washer Fluid It will illuminate when the windshield washer fluid is low. Powertrain Malfunction/Reduced Power Illuminates when a powertrain fault has been detected. Contactyour authorized dealer as soon as possible. Security/Anti-Theft System Flashes when the SecuriLock 威 passive anti-theft syst...

Stability Control System Displays when the AdvanceTrac 威 /Traction control is active. If the light remains on, have the system serviced immediately. Stability Control System Off Illuminates when AdvanceTrac 威 /Traction control has been disabled by the driver. Transmission Tow/Haul Illuminates when t...

GENERAL INFORMATION WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that maytake their focus off the road. Your primary responsibility is the safeoperation of the ...

based on your recent driving history of 500 miles (800 km). This valueis not the same as the average fuel economy display. The runningaverage fuel economy is re-initialized to a factory default value if thebattery is disconnected. • AVG MPG (L/100km): Average fuel economy displays your average fuele...

Compass calibration adjustment Note: For optimum calibration, drive to an open, level location away from large metallic objects or structures. Switch off all non-essentialelectrical accessories (heated rear window, heater, A/C, map lamps,wiper, etc.) and make sure all the doors are closed Note: If t...

Press and hold the SELECT/RESET stem to get into the setup menusequence for the following displays: SETUP HOLD RESETFOR SYSTEMCHECK press and holdtheSELECT/RESETstem OIL LIFE CHARGING SYSTEM WASHER FLUID LEVEL DOOR AJAR STATUS LIFTGATE/GLASS AJAR STATUS BRAKE SYSTEM MYKEY DISTANCE(if programmed) X M...

Information Display Controls (Type 2) • Press the INFO button to scrollthrough trip, fuel usage, andMyKey 威 information. • Press the SETUP button to scrollthrough various vehicle featuresettings. • Press the RESET button to choose settings, reset information andconfirm messages. Info Press the INFO ...

GENERAL AUDIO INFORMATION Radio Frequencies and Reception Factors AM and FM frequencies are established by the Federal CommunicationsCommission (FCC) and the Canadian Radio and TelecommunicationsCommission (CRTC). Those frequencies are: AM: 530, 540–1700, 1710 kHz FM: 87.9–107.7, 107.9 MHz Radio rec...

MP3 Track and Folder Structure Audio systems capable of recognizing and playing MP3 individual tracksand folder structures work as follows: • There are two different modes for MP3 disc playback: MP3 trackmode (system default) and MP3 folder mode. • MP3 track mode ignores any folder structure on the ...

• If SYNC is selected, press + or – to scroll through the differentoptions: SYNC USB, SYNC BTST and SYNC LINE. For moreinformation on SYNC, see the SYNC 威 chapter. C. Right arrow button • In radio mode, press and release to scroll through memory presets.Press and hold to seek to the next station. • ...

To use any rear controls (whether in Single Play or Dual Play mode), therear seat controls must be switched on. To switch on Dual Play, the rearseat controls must be switched on and the headphone icon illuminated inthe audio display. See Activating the rear audio controls previously. AUXILIARY INPUT...

SATELLITE RADIO INFORMATION (IF EQUIPPED) Satellite Radio Channels SIRIUS 威 broadcasts a variety of music, news, sports, weather, traffic and entertainment satellite radio channels. For more information and acomplete list of SIRIUS 威 satellite radio channels, visit www.siriusxm.com in the United Sta...

REAR SEAT ENTERTAINMENT SYSTEM (IF EQUIPPED) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that you use extreme caution when using any device or feature that may takeyour focus off the road. Your primary responsibility is the s...

Wireless FM Transmitter Your device may be equipped with an external FM transmitter, whichallows you to listen to the audio signal by tuning your vehicle’s FM radioto the selected frequency and turning SOUND AROUND on with theremote. Whenever the SOUND AROUND is on, broadcast radio receptionmay be p...

K. SOURCE button: Press this button to select between Monitor A, Monitor B, AUX/TV (if available), and AUX 2 (if available). L. POWER button: Press this button to turn the system on or off. M. TFT LCD panel: Seven-inch TFT LCD panel. N. Level lock and release latch: Allows the user to adjust the vie...

Button Function Descriptions Note: The remote control only operates this device. It is not a universal remote control and does not control other equipment. 1. SOURCE: Any video equipment connected to the audio/video inputs can be used with the monitor by pressing this button. Each time thebutton is ...

8. UP/DOWN: • For DVD: Navigation button, you can use this button to move theselect bar to items among the menu or file list. • For TV: Use these buttons to advance to the next higher or lowerchannel. • For OSD: Increase or decrease the setting of selected item. 9. LEFT/RIGHT: Navigation button; you...

26. REPEAT: Press this button to switch the repeat mode by ALL, TITLE, CHAPTER and cancel the repeat mode while playing DVD-video.Other disc types such as VCD, CD, and SVCD only have two repeatmodes that can be selected: TRACK and ALL. Note: Both repeat functions of VCD and SVCD need the PBC status ...

DVD Basics To get the most use out of each DVD, make sure you read this sectioncompletely. Regional Coding Both the DVD player and disc are coded by region. These regional codesmust match in order for the disc to play. If the codes do not match, thedisc does not play by default. The system is preset...

Playing an Audio CD When playing an audio CD, the DISPLAY banner appears automatically. Itdisplays the current track and the amount of time the track has beenplaying, the total amount of time on the disc and the current timerunning on the disc. Press the DISPLAY button on the remote control to displ...

Selecting a Play Mode You can choose what order the songs play on a disc temporarily. TheFOLDER play mode is the default. To access the play mode operations,press the REPEAT button on the remote control. The play mode optionsare as follows: • Single: Play a selected song. • Repeat One: Repeat the so...

Connecting an MP3 Device Connecting an MP3 Device to Your DVD-headrest Module via USB Plug the MP3 Dock Connector to USB cable into a high-power USB porton your DVD-headrest module, and then connect the other end to theplayer. See the documentation that came with your device for more information. Ch...

Compliance Information FCC Notice This device has been tested and found to comply with the limits for aClass B digital device, pursuant to part 15 of the FCC Rules. These limitsare designed to provide reasonable protection against harmfulinterference in a residential installation. This device genera...

MANUAL HEATING AND AIR CONDITIONING SYSTEM WITHOUTAUXILIARY CLIMATE CONTROL A. Fan speed control: Controls the volume of air circulated in your vehicle. Turn to select the desired fan speed or switch off. If you switchthe fan off, the windshield may fog up. B. Temperature control: Controls the tempe...

O (Off): Turns the system on and off. When the system is off, outside air is prevented from entering the vehicle. Distributes air through the floor vents. Distributes air through the windshield defroster vents, demistervents and floor vents. Distributes air through the windshield defroster vents and...

O (Off): Turns the system on and off. When the system is off, outside air is prevented from entering the vehicle. Distributes air through the floor vents. Distributes air through the windshield defroster vents, demistervents and floor vents. Distributes air through the windshield defroster vents and...

When this button is pressed, the display only shows the rear temperaturesetting. After the rear setting changes are completed on the frontcontrol, the display automatically shows both climate settings. F. Passenger temperature control: Press and turn to increase or decrease the air temperature on th...

F. REAR (temperature control): Press to turn on the auxiliary climate control system and to set the desired rear temperature with the frontcontrol. The rear temperature is the same as the front temperature whenonly the center rear temperature bar is lit. The rear temperature isdifferent from the fro...

Distributes air through the floor vents. Distributes air through the windshield defroster vents, demistervents and floor vents. Distributes air through the windshield defroster vents anddemister vents. This setting can also be used to defog and clearthe windshield of a thin covering of ice. N. Drive...

AUXILIARY CLIMATE CONTROL (IF EQUIPPED) Your auxiliary climate controls are located on the rear of the centerconsole and can be used when REAR has been pressed on the frontclimate control system. The temperature is set by the front controls. Usethe rear control to adjust the fan speed or turn the au...

Recommended settings for cooling: • Adjust the air distribution control to the NORM A/C position. If your vehicle stationary for extended periods during extreme highambient temperatures • Select MAX A/C position. For maximum cooling performance, turn the air distribution control toMAX A/C. To aid in...

To aid in side window defogging and demisting in cold or humid weather:1. Select Floor/Panel.2. Select A/C.3. Adjust the temperature control to maintain comfort.4. Set the fan speed to the highest setting.5. Direct the outer instrument panel vents toward the side windows.6. To increase airflow to th...

SITTING IN THE CORRECT POSITION WARNING: Sitting improperly out of position or with the seatback reclined too far can take off weight from the seat cushion and affect the passenger sensing system, resulting in seriousinjury or death in a crash. Always sit upright against your seatback,with your feet...

Power Lumbar (if equipped) The control is located on theoutboard side of the seat. Press theforward or rearward side of thecontrol for more or less support. MEMORY FUNCTION (IF EQUIPPED) This feature will save and recall the positions of the driver seat, powermirrors and adjustable pedals. The memor...

Recalling Saved Memory Positions To recall position 1 settings, press and release memory button 1. Thememory features will move to the saved memory 1 position. The memory positions can also be recalled when you: • press your remote entry transmitter unlock control (if the transmitteris programmed to...

Heated and Cooled Seats Air Filter Replacement (If Equipped) The heated and cooled seat system includes air filters that must bereplaced periodically. See scheduled maintenance information for more information. There is a filter located under each front seat. The filter can be accessedfrom the secon...

REAR SEATS Folding Down the 2nd Row 40% Seat System WARNING: Use caution when folding the seat back to the flat back position as the system will move forward when you lift the release handle. WARNING: Before returning the seat back to its original position, make sure that cargo or any objects are no...

2. Locate handle on the side of theseat cushion by the door. 3. Pull up on the handle and pushthe seat back forward toward thefront of the vehicle. To return the seat to the upright position: 1. Lift the seat back toward the rearof the vehicle. 2. Rotate the seat back until youhear a click, locking ...

Placing the 2nd Row Outboard 40% Seats in Cargo Mode WARNING: Use caution when folding the seat back to the flat back position as the system will move forward when you lift the release handle. WARNING: Always return the seat from the kneel position prior to raising the seat back. Failure to do so co...

Adjusting the 2nd Row Outboard 40% Seat for E-Z Entry WARNING: Always latch the vehicle seat to the floor, whether the seat is occupied or empty. If not latched, the seat may cause injury during a sudden stop. WARNING: After using the E-Z Entry feature make sure there are not any objects, cargo or t...

To return the seat to a seating position: 1. Push the seat down and latch tothe floor. 2. Bring the seat back to an uprightposition. The seat back should lockinto position. Note : If the seat back will not return to the upright position, tumble the seat again and re-latch it to the floor. Be sure th...

Reclining the 2nd Row Outboard 40% Seatback WARNING: Reclining the seat back can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. Locate the release handle on theoutboard side of the seat cushion.Lift to allow the seatback to...

2. With the latch released theseatback can be lowered into theload floor position. 3. To return the seat to the uprightposition, lift the seatback until thelatch is fully engaged. Adjusting the 2nd Row Center 20% Seat (if equipped) Note: This seat can be moved forward to keep a child in a child rest...

Rear Heated Seats (if equipped) WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions,must exercise care when using the seat heater. The seat heater maycause b...

Folding Down the 3rd Row Seats to the Load Floor WARNING: To prevent possible damage to the seat or safety belts, make sure that the safety belts are not buckled when moving the seat to the load floor position. WARNING: Before returning the seat back to its original position, make sure that cargo or...

UNIVERSAL GARAGE DOOR OPENER The appearance of your vehicle’s universal garage door opener will varyaccording to your option package. Before programing, make sure youidentify which transmitter you have by comparing it to the graphics below. HomeLink 威 Car2U 威 Home Automation System Note: The program...

Rolling Code Programming Note: If you do not follow the time-sensitive instructions, the device will time out and you will have to repeat the complete procedure. Note: It may be helpful to have another person assist you in programming the transmitter. 1. Switch the ignition on. 2. Press and hold the...

8. The LED lamp will begin to flash rapidly until programming iscomplete. If your garage door does not operate, repeat the previoussteps. Otherwise, call the toll-free help line at 1-866-572-2728. The LED lamp above the selected button will illuminate to confirm thatthe system is responding to the b...

4. Press and hold the function button you programmed for 5 seconds,then release. You may need to do this twice to activate the door. If yourgarage door does not operate, observe the indicator light. If the indicator light stays on, programming is complete. Press andrelease the programmed button to a...

Reprogramming a single button To program a device to a previously trained button, follow these steps: 1. Press and hold the desired button. Do NOT release the button. 2. The indicator light will begin to flash after 20 seconds. Withoutreleasing the button, follow Step 1 in the Programming section. F...

AUXILIARY POWER POINTS WARNING: Do not plug optional electrical accessories into the cigarette lighter socket (if equipped). Improper use of the lighter can cause damage not covered by your warranty, and can result in fireor serious injury. Note: If used when the engine is not running, the battery w...

CENTER CONSOLE (IF EQUIPPED) WARNING: Use only soft cups in the cupholder. Hard objects can injure you in a collision. Your vehicle may be equipped with a variety of console features. Theseinclude: 1. Cupholders 2. Utility compartment, coin holderslots, tissue box holder, audio inputjack and USB por...

3. Turn the key to start the engine. The engine may continue cranking for up to 15 seconds or until the vehicle starts. Note: If the engine does not start on the first try, wait for a short period of time and try again. If you have difficulty starting the engine when the temperature is below-13°F (-...

We recommend that you do the following for safe and correct operation: • Use a 16-gauge outdoor extension cord that is product certified byUnderwriter’s Laboratory or Canadian Standards Association. Thisextension cord must be able to be used outdoors, in coldtemperatures, and be clearly marked Suita...

SAFETY PRECAUTIONS WARNING: Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. WARNING: The fuel system may be under pressure. If you hear a hissing sound near the fuel filler door (Easy Fuel 威 no cap fuel system), do not refuel until...

• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes,remove contact lenses (if worn), flush with water for 15 minutes andseek medical attention. Failure to seek proper medical attention couldlead to permanent injury. • Fuels can also be harmful if absorbed through the skin. If f...

It is best not to alternate repeatedly between gasoline and E85. If you doswitch fuels, it is recommended that you add as much fuel aspossible—at least half a tank. Do not add less than five gallons (18.9L)when refueling. You should drive the vehicle immediately after refuelingfor at least 5 miles (...

Refilling With a Portable Fuel Container WARNING: Do not insert the nozzle of portable fuel containers or aftermarket funnels into the Easy Fuel 威 system. This could damage the fuel system and its seal, and may cause fuel to run onto theground instead of filling the tank, which could result in serio...

4. Slowly insert the fuel filler nozzle fully into the fuel system, and leavethe nozzle fully inserted until you are done pumping. 5. After you are done pumping fuel, slowly remove the fuel fillernozzle—allow about ten seconds after pumping fuel before removing thefuel filler nozzle. This allows res...

For consistent results when filling the fuel tank: • Turn the ignition off before fueling; an inaccurate reading results if theengine is left running. • Use the same fill rate (low–medium–high) each time the tank is filled. • Allow no more than two automatic click–offs when filling. Results are most...

EMISSION CONTROL SYSTEM WARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. WARNING: Exhaust leaks may result in entry of harmful and potentially lethal fumes into th...

AUTOMATIC TRANSMISSION WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the off position and remove the key whenever you leave your vehicle. WARNING: Do not use the Tow/Haul feature when driving in icy or slippery conditions as the ...

Brake-Shift Interlock – Floor-Shift Transmission WARNING: Do not drive your vehicle until you verify that the brake lamps are working. WARNING: When doing this procedure, you will be taking the vehicle out of park which means the vehicle can roll freely. To avoid unwanted vehicle movement, always fu...

If the fuse is not blown, perform the following procedure: 1. Apply the parking brake. 2. Turn the key to the off position. 3. Remove the access plug on top ofthe steering column. 4. Using a flat-head screwdriver orsimilar tool, move the brake-shiftinterlock actuator spindle towardthe left, apply th...

USING FOUR-WHEEL DRIVE (4WD) (IF EQUIPPED ) WARNING: For important information regarding safe operation of this type of vehicle, see General Information in the Wheels and Tires chapter. Note: Do not use 4X4 mode on dry, hard surfaced roads. Doing so will produce excessive noise, increase tire wear a...

4WD switch positions WARNING: Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorilyunder off-road conditions. Avoid sharp turns or abrupt maneuvers inthese vehicles. Note: If...

• 4L (4X4 LOW) provides electronically locked four-wheel drive when extra power at reduced speeds is required. The message center willdisplay 4X4 LOW when this mode is selected. This mode is notrecommended for use on dry pavement. Use this mode for off-roadlow-speed operation or when extra power is ...

How Your Vehicle Differs From Other Vehicles WARNING: Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drivevehicles are not designed for cornering at speeds as high as passe...

GENERAL INFORMATION Note: Occasional brake noise is normal. If a metal-to-metal, continuous grinding or continuous squeal sound is present, the brake linings may beworn-out and should be inspected by an authorized dealer. If yourvehicle has continuous vibration or shudder in the steering wheel while...

PRINCIPLES OF OPERATION The traction control system helps avoid drive wheel spin and loss oftraction. If your vehicle begins to slide, the system applies the brakes to individualwheels and, when needed, reduces engine power at the same time. If thewheels spin when accelerating on slippery or loose s...

PRINCIPLES OF OPERATION WARNING: Vehicle modifications involving braking system, aftermarket roof racks, suspension, steering system, tire construction or wheel/tire size may change the handling characteristicsof the vehicle and may adversely affect the performance of theAdvanceTrac 威 system. In add...

SENSING SYSTEM (IF EQUIPPED) WARNING: To help avoid personal injury, please read and understand the limitations of the system as contained in this section. Sensing is only an aid for some (generally large and fixed)objects when moving in reverse on a flat surface at parking speeds.Traffic control sy...

Using the Front and Rear Sensing System Rear Sensing System The rear sensors are only active when the transmission is in R (Reverse).As the vehicle moves closer to the obstacle, the rate of the audiblewarning increases. When the obstacle is fewer than 10 inches (25centimeters) away, the warning soun...

Front Sensing System The front sensors are active when the gearshift is in any position otherthan P (Park) or N (Neutral) and the vehicle speed is below 8 mph(13 km/h). A. Coverage area of up to 27 inches(70 centimeters) from the front ofthe vehicle and about 6–9 inches(15–23 centimeters) to the sid...

Using the Rear View Camera System The rear view camera system displays what is behind your vehicle whenyou place the transmission in R (Reverse). The system uses two types ofguides to help you see what is behind your vehicle:1. Fixed guidelines: Show the actual path the vehicle is moving in while re...

Guidelines and the Centerline Note: Fixed guidelines are only available when the transmission is in R (Reverse). Note: The centerline is only available if fixed guidelines are on. A. Rear bumper B. Fixed guideline: Red zone C. Fixed guideline: Yellow zone D. Fixed guideline: Green zone E. Centerline...

STEERING Your vehicle is equipped with power steering. Power steering uses energyfrom the engine to decrease the driver’s effort in steering the vehicle. To help prevent damage to the power steering pump: • Never hold the steering wheel to the extreme right or the extreme leftfor more than a few sec...

ROOF RACKS AND LOAD CARRIERS WARNING: When loading the roof rail crossbars, it is recommended to evenly distribute the load, as well as maintain a low center of gravity. Loaded vehicles, with higher centers of gravity,may handle differently than unloaded vehicles. Extra precautions, suchas slower sp...

LOAD LIMIT Vehicle Loading – With and Without a Trailer This section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehicle weight within its design ratingcapability, with or without a trailer. Properly loading your vehicle willprovide maximum return of vehic...

Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weigh...

• Example only: WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structuraldamage, serious damage to the vehicle, loss of control and personalinjury. 244 Load Carrying 20...

GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo andpassengers – that the vehicle can handle without r...

WARNING: Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tires with ahigher limit than the original tires do not increase the GVWR andGAWR limitations. WARNING: Exceeding any vehicle ...

To move the shelf to the dividerposition: Pull up and pivot the shelf over the channels on the sidetrim panels and snap vertically inplace. POWER DEPLOYABLE RUNNING BOARDS (IF EQUIPPED) WARNING: In extreme climates, excessive ice buildup may occur, causing the running boards not to deploy. Be sure t...

The running boards automaticallymove when the doors are opened toassist entering and exiting thevehicle. Automatic Power Deploy The running boards will extend down and out when the doors areopened. Automatic Power Stow The running boards will return to the stowed position after a two seconddelay whe...

TOWING A TRAILER WARNING: Do not exceed the GVWR or the GAWR specified on the certification label. WARNING: Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage, transmission damage, structural damage, lossof vehicle c...

This feature applies the vehicle brakes at individual wheels and, ifnecessary, reduces engine power. If the trailer begins to sway, thestability control light flashes and the message TRAILER SWAY REDUCE SPEED appears in the information display. The first thing to do is slow the vehicle down, then pu...

2WD/4WD Towing Package Maximum GCWR - lb (kg) 4WD EL (U.S.)4WD Max (Canada) Standard 12300 (5579) 4WD EL (U.S.)4WD Max (Canada) Optional 15000 (6804) ESSENTIAL TOWING CHECKS Follow these guidelines for safe towing: • Do not tow a trailer until your vehicle has been driven at least1000 miles (1600 ki...

The standard integrated hitch has two ratings depending on mode ofoperation: • Weight-carrying requires a draw bar and hitch ball. The draw bar supports all the vertical tongue load of the trailer. • Weight-distributing requires an aftermarket weight-distributing system which includes draw bar, hitc...

Weight-distributing Hitch – Vehicles with Air Suspension WARNING: Do not adjust a weight-distributing hitch to any position where the rear bumper of the vehicle is higher than it was before attaching the trailer. Doing so will defeat the function of theweight-distributing hitch, which may cause unpr...

Trailer Brakes WARNING: Do not connect a trailer’s hydraulic brake system directly to your vehicle’s brake system. Your vehicle may not have enough braking power and your chances of having a collision greatlyincrease. Electric brakes and manual, automatic or surge-type trailer brakes aresafe if inst...

The TBC user interface consists of the following: A. +/- (GAIN adjustment buttons): Pressing these buttons adjusts the TBC’s power output to the trailer brakes (in 0.5 increments). The GAINsetting can be increased to a maximum of 10.0 or decreased to aminimum of 0 (no trailer braking). Pressing and ...

B. Manual control lever: Slide the control lever to the left to activate power to the trailer’s electric brakes independent of the tow vehicle’sbrakes (see the following Procedure for adjusting GAIN section for instructions on proper use of this feature). If the manual control isactivated while the ...

Explanation of Information Display Warning Messages Note: Your TBC can be diagnosed by your authorized dealer to determine exactly which trailer fault has occurred. However, if the faultis with the trailer this diagnosis is not covered under your Ford warranty. TRAILER BRAKE MODULE FAULT: Displays i...

• Your vehicle’s brake system and the trailer brake system workindependently of each other. Changing the GAIN setting on the TBCdoes not affect the operation of your vehicle’s brakes whether atrailer is attached or not. • When the vehicle is turned off, the TBC output is disabled and thedisplay and ...

• If your vehicle is equipped with AdvanceTrac™ with RSC, you mayexperience AdvanceTrac™ with RSC activations during typicalcornering maneuvers with a heavily loaded trailer; this is normal.Cornering at a slower speed while towing reduces the tendency of theAdvanceTrac™ stability enhancement system ...

Replace the rear axle lubricant anytime the rear axle has beensubmerged in water. Water may have contaminated the rear axlelubricant, which is not normally checked or changed unless a leak issuspected or other axle repair is required. WRECKER TOWING Note: Vehicles equipped with air suspension must t...

Two-wheel drive (2WD) vehicles can be towed with the front wheels onthe ground (without dollies) and the rear wheels off the ground. It is recommended that four-wheel drive (4WD) vehicles are to be towedwith a wheel lift and dollies or flatbed equipment with all the wheels offthe ground. TOWING THE ...

BREAKING-IN You need to break in new tires for approximately 300 miles(480 kilometers). During this time, your vehicle may exhibit some uniquedriving characteristics. Avoid driving too fast during the first 1000 miles(1600 kilometers). Vary your speed frequently and change up throughthe gears early....

• Carry unnecessary weight (approximately 1 mpg [0.4 km/L] is lost forevery 400 lb [180 kg] of weight carried). • Add particular accessories to your vehicle (e.g. bug deflectors,rollbars/light bars, running boards, ski racks). • Drive with the wheels out of alignment. DRIVING THROUGH WATER Note: Dri...

FLOOR MATS WARNING: Always use floor mats that are designed to fit the foot well of your vehicle. Only use floor mats that leave the pedal area unobstructed. Only use floor mats that are firmly secured toretention posts so that they cannot slip out of position and interferewith the pedals or impair ...

WARNING (Continued) • Failure to properly follow floor mat installation or attachmentinstructions can potentially cause interference with pedal operationcausing loss of control of vehicle. • To install floor mats, position the floor mat so that the eyelet is overthe retention post and press down to ...

ROADSIDE ASSISTANCE Vehicles Sold in the U.S. : Getting Roadside Assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24-hours ...

U.S. Ford vehicle customers who require Roadside Assistance, call1-800-241-3673. If you need to arrange roadside assistance for yourself, Ford MotorCompany will reimburse a reasonable amount for towing to the nearestdealership within 35 miles (56 kilometers). To obtain reimbursementinformation, U.S....

Connecting the Jumper Cables WARNING: Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery. Note: Do not attach the negative (-) cable to fuel lines, engine rocker covers, the intake...

Removing the Jumper Cables Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery. Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable fromthe ground metal surface. 2. Remove the jumper cable on thenega...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizeddealer. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfaction. Plea...

• Ford Genuine Accessories • Service specials and promotions. In Canada: Mailing address Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Additional assistance If you have questions or concerns,...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

CHANGING A FUSE Fuses WARNING: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. If electrical components in the vehicleare not working, a fuse may haveblown. Blown fuses are identifi...

FUSE SPECIFICATION CHART Power Distribution Box WARNING: Always disconnect the battery before servicing high current fuses. WARNING: To reduce risk of electrical shock, always replace the cover to the power distribution box before reconnecting the battery or refilling fluid reservoirs. The power dis...

Fuse/Relay Location Fuse Amp Rating Protected Circuits 82 — Not used 83 — Not used 84 — Not used 85 — Wiper motor relay * Mini Fuses ** Cartridge Fuses Passenger Compartment Fuse Panel The fuse panel is located under the right-hand side of the instrumentpanel. To remove the trim panel for accessto t...

GENERAL INFORMATION WARNING: Turn off the power running boards, if equipped, before working under the vehicle, jacking or placing any object under the vehicle. Never place your hand between the extendedrunning board and the vehicle. A moving running board may causeinjury. Have your vehicle serviced ...

Working with the Engine On WARNING: To reduce the risk of vehicle damage and/or personal burn injuries, do not start your engine with the air cleaner removed and do not remove it while the engine is running. 1. Set the parking brake and shift to P (Park). 2. Block the wheels. OPENING AND CLOSING THE...

UNDER HOOD OVERVIEW 5.4L V8 A. Windshield washer fluid reservoir B. Engine oil dipstick C. Brake fluid reservoir D. Engine coolant reservoir E. Air filter assembly F. Power steering fluid reservoir G. Power distribution box H. Engine oil filler cap I. Battery A B C D E F G H I 292 Maintenance 2013 E...

ENGINE OIL DIPSTICK A. – MIN B. – MAX ENGINE OIL CHECK Refer to the scheduled maintenance information for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait 15 minutes for the oil to drain into theoil pan. 3. Set the pa...

Only use oils certified for gasoline engines by theAmerican Petroleum Institute (API). An oil with thistrademark symbol conforms to the current engine andemission system protection standards and fueleconomy requirements of the International LubricantsSpecification Advisory Council (ILSAC), comprised...

Adding Engine Coolant WARNING: Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hotengine parts. WARNING: Do not put engine coolant in the windshield washer fluid contai...

• Do not add extra inhibitors or additives to the coolant. These can beharmful and compromise the corrosion protection of the engine coolant. Unscrew the cap slowly. Any pressure will escape as you unscrew thecap. Add prediluted engine coolant meeting the Ford specification. See Capacities and Speci...

What You Should Know About Fail-Safe Cooling If the engine coolant supply is depleted, this feature allows the vehicle tobe driven temporarily before incremental component damage is incurred.The “fail-safe” distance depends on ambient temperatures, vehicle loadand terrain. How Fail-Safe Cooling Work...

WARNING: Never remove the coolant reservoir cap while the engine is running or hot. You have limited engine power when in the fail-safe mode, so drive thevehicle with caution. The vehicle will not be able to maintain high-speedoperation and the engine will run rough. Remember that the engine iscapab...

POWER STEERING FLUID CHECK Check the power steering fluid. Refer to scheduled maintenance information. 1. Start the engine and let it run until it reaches normal operatingtemperature (the engine coolant temperature gauge indicator will benear the center of the normal area between H and C). 2. While ...

CHANGING THE VEHICLE BATTERY WARNING: Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near thebattery, always shield your face and protect your eyes. Always provideproper v...

If you see any corrosion on the battery or terminals, remove the cablesfrom the terminals and clean with a wire brush. You can neutralize theacid with a solution of baking soda and water. It is recommended that the negative battery cable terminal bedisconnected from the battery if you plan to store ...

CHANGING THE WIPER BLADES Replace wiper blades at least once per year for optimum performance. To replace the wiper blades: 1. Fold back the wiper arm andposition the wiper blade at a rightangle to the wiper arm. 2. To remove the wiper blade, pressthe retaining clip (A) to disengagethe wiper blade, ...

4. To attach the new wiper to thewiper arm, align the cross pin andkeyway (denoted with the arrows)and firmly press the wiper bladeinto the wiper arm until an audiblesnap is heard. If you find this procedure too difficult, please see your dealer. AIR FILTER CHECK WARNING: To reduce the risk of vehic...

Changing the Air Filter Element 1. Locate the mass air flow sensorelectrical connector on the airoutlet tube. This connector willneed to be unplugged. 2. Unlock the locking clip on theconnector (connector shown frombelow for clarity), then squeeze andpull the connector off of the airoutlet tube. 3. ...

ADJUSTING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant.If your vehicle has been in an accident, the alignment of your headlampsshould be checked by your authorized dealer. Vertical Aim Adjustment Before aim adjustment, disable the air suspension system. Refer ...

5. Locate the vertical adjuster oneach headlamp, then use a Phillips#2 screwdriver to turn the adjustereither counterclockwise orclockwise in order to adjust thevertical aim of the headlamp. Theupper edge of the light patternshould line up to the horizontal line. 6. Repeat Steps 3–5 for the otherhea...

Replacing Headlamp Bulbs WARNING: Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause thebulb to break the next time the headlamps are operated. 1. Make sure that the headlam...

Replacing Tail, Stop, Turn Signal, Side Marker, and Backup LampBulbs The tail, stop, turn signal, side marker, and backup lamp bulbs arelocated in the same portion of the tail lamp assembly, one just below theother. Follow the same steps to replace any bulb: 1. Make sure the headlamp switch isin the...

Replacing License Plate Lamp Bulbs The license plate bulbs are located in the license plate housing assemblyon the liftgate. To change the license plate bulbs: 1. Make sure the headlamp switch isin the off position. 2. Remove the license lamp screwfrom the assembly. 3. Pull the lamp down and twist t...

WAXING • Wash the vehicle first. • Use a quality wax that does not contain abrasives. • Do not allow paint sealant to come in contact with any non-body(low-gloss black) colored trim, such as grained door handles, roofracks, bumpers, side moldings, mirror housings or the windshield cowlarea. The pain...

For fabric, carpets, cloth seats, safety belts and seats equipped with sideairbags: • Remove dust and loose dirt with a vacuum cleaner. • Remove light stains and soil with Motorcraft 威 Professional Strength Carpet & Upholstery Cleaner. • If grease or tar is present on the material, spot-clean th...

CLEANING LEATHER SEATS(IF EQUIPPED WITH THE KING RANCH 姞 EDITION) Your vehicle is equipped with seating covered in premium, top-grainleather which is extremely durable, but still requires special care andmaintenance in order to ensure longevity and comfort. Regular cleaning and conditioning will mai...

CLEANING THE ALLOY WHEELS Note: Do not use chrome cleaner, metal cleaner or polish on wheels and wheel covers. Aluminum wheels and wheel covers are coated with a clear coat paintfinish. In order to maintain their shine: • Clean weekly with Motorcraft 威 Wheel and Tire Cleaner. Heavy dirt and brake du...

Brakes • Make sure brakes and parking brake are fully released. Tires • Maintain recommended air pressure. Miscellaneous • Make sure all linkages, cables, levers and pins under vehicle arecovered with grease to prevent rust. • Move vehicles at least 25 feet (8 meters) every 15 days to lubricateworki...

GENERAL INFORMATION Notice to Utility Vehicle, Van and Truck Owners WARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles. To reduce the risk of serious injury or death from a rollover or other crash you must: • Avoid sharp turns and abrupt maneuvers; • Dri...

How Your Vehicle Differs from Other Vehicles SUVs, vans and trucks can differfrom some other vehicles in a fewnoticeable ways. Your vehicle maybe: • Higher – to allow higher loadcarrying capacity and to allow itto travel over rough terrainwithout getting hung up ordamaging underbodycomponents. • Sho...

TIRE CARE Information About Uniform Tire Quality Grading Tire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereapplicable on the tire sidewall betweentread shoulder and maximum sectionwidth. For example: • Treadwear 200 Traction AA Temperature A These Tir...

INFORMATION CONTAINED ON THE TIRE SIDEWALL Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identifi...

E. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheeldiameter. F. 95: Indicates the tire’s load index. It is an index that relates to how much weight a tire can carry. You may find this information in yourowner...

Information on T Type Tires T type tires have some additionalinformation beyond those of P typetires; these differences aredescribed below. T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Gradesdo not apply to thi...

INFLATING YOUR TIRES Safe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air pressurewithout appearing flat. Every day before you drive, check your tires. If one looks lower than theothers, use a tire gauge to check pressure o...

Damage Periodically inspect the tire treads and sidewalls for damage (such asbulges in the tread or sidewalls, cracks in the tread groove andseparation in the tread or sidewall). If damage is observed or suspected,have the tire inspected by a tire professional. Tires can be damagedduring off-road us...

Tire Replacement Requirements WARNING: Only use replacement tires and wheels that are the same size, load index, speed rating and type (such as P-metric versus LT-metric or all-season versus all-terrain) as those originallyprovided by Ford. The recommended tire and wheel size may be found oneither t...

Important: Remember to replace the wheel valve stems when the road tires are replaced on your vehicle. It is recommended that the two front tires or two rear tires generally bereplaced as a pair. The tire pressure sensors mounted in the wheels (originally installed onyour vehicle) are not designed t...

Tire and Wheel Alignment A bad jolt from hitting a curb or pothole can cause the front end of yourvehicle to become misaligned or cause damage to your tires. If yourvehicle seems to pull to one side when you are driving, the wheels maybe out of alignment. Have an authorized dealer check the wheelali...

USING SNOW CHAINS WARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety and performanceof your vehicle, which could result in an increased risk of loss of vehiclecontrol, vehicl...

TIRE PRESSURE MONITORING SYSTEM WARNING: The tire pressure monitoring system is NOT a substitute for manually checking tire pressure. The tire pressure should be checked periodically (at least monthly) using a tire gauge.See Inflating Your Tires in this chapter. Failure to properly maintain your tir...

telltale after replacing one or more tires or wheels on your vehicle toensure that the replacement or alternate tires and wheels allow theTPMS to continue to function properly. The tire pressure monitoring system complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is...

When you believe your system is not operating properly The main function of the tire pressure monitoring system is to warn youwhen your tires need air. It can also warn you in the event the system isno longer capable of functioning as intended. Refer to the following chartfor information concerning ...

Low tirepressurewarning light Possible cause Customer action required Flashing warninglight Spare tire in use Repair the damaged road wheel/tireand reinstall it on the vehicle torestore system functionality. For adescription on how the systemfunctions, refer to When your temporary spare tire is inst...

CHANGING A ROAD WHEEL WARNING: The use of tire sealants may damage your tire pressure monitoring system (TPMS) and should not be used. However, if you must use a sealant, the TPMS sensor and valve stem onthe wheel must be replaced by an authorized Ford dealer. WARNING: See Tire Pressure Monitoring S...

The usage of a full-size dissimilar spare tire and wheel assembly can leadto impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability • All-wheel driving...

Removing the jack and tools 1. Open the liftgate, then locate theaccess panel on the floor behind the3rd row seat. Unlatch and removethe panel. 2. Remove the jack and tools assembly tray from the compartment byturning the wing-nut counterclockwise to relieve tension against the jackassembly tray. Re...

12. Raise the vehicle to provide sufficient ground clearance wheninstalling the spare tire; approximately 1/4 inch (6 mm). • Front • Rear • Jack at the specified locations to avoid damage to the vehicle. 13. Remove the lug nuts with the lug wrench. 14. Replace the flat tire with the spare tire, maki...

TECHNICAL SPECIFICATIONS Wheel Lug Nut Torque Specifications WARNING: When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum orbrake disc that contacts the wheel. Ensure that any fast...

VEHICLE IDENTIFICATION NUMBER The vehicle identification number islocated on the driver sideinstrument panel. Please note that in the graphic,XXXX is representative of yourvehicle identification number. The Vehicle Identification Number (VIN) contains the followinginformation: A. World manufacturer ...

ACCESSORIES For a complete listing of the accessories that are available for yourvehicle, please contact your dealer or visit our online store at: Accessories.Ford.com (U.S. only). Ford Custom Accessories are available for your vehicle through yourlocal Ford or Ford of Canada dealer. Ford Motor Comp...

FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY) More than 32 million Ford and Lincoln owners have discovered thepowerful protection of Ford ESP. It is the only extended service planbacked by Ford Motor Company, and provides “peace of mind”protection beyond the New Vehicle Limited Warranty coverage. Up t...

FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY) You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is the only service contractbacked by Ford Motor Company of Canada, Limited. Depending on theplan you purchase, Ford ESP provides benefits such as: • R...

GENERAL MAINTENANCE INFORMATION Why Maintain Your Vehicle? Carefully following the maintenance schedule helps protect against majorrepair expenses resulting from neglect or inadequate maintenance andmay also help to increase the value of your vehicle when you sell ortrade it. Keep all receipts for c...

Protecting Your Investment Maintenance is an investment that will pay dividends in the form ofimproved reliability, durability and resale value. To maintain the properperformance of your vehicle and its emission control systems, it isimperative that scheduled maintenance be completed at the designat...

NORMAL SCHEDULED MAINTENANCE AND LOG The following section contains the Normal Scheduled Maintenance. Thisschedule is presented at specific mileage (kilometer) intervals withexceptions as noted. Normal Scheduled Maintenance Every 7500 miles(12000 km) or sixmonths (whichevercomes first) Change engine...

Additional Maintenance Items Every 30000 miles(48000 km) Replace climate-controlled (heated andcooled) seat filter (if equipped). Replace engine air filter. Every 97500 miles(156000 km) Replace spark plugs. Every 105000 miles(168000 km) Change engine coolant. * Inspect accessory drive belt(s). ** Ev...

Maintenance Schedule Log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ...

Extensive Idling or Low-speed Driving for Long Distances as in Heavy Commercial Use (i.e., Delivery, Taxi, Patrol Car or Livery) Inspect frequently,service as required Replace engine air filter. Every 5000 miles(8000 km) Inspect brake system. Inspect wheels and related components forabnormal noise, ...

Off-road Operation Inspect frequently,service as required Inspect steering linkage, ball joints andU-joints. Lubricate if equipped with greasefittings. Replace engine air filter. Every 5000 miles(8000 km) Change engine oil and filter. * Inspect the wheels and related components forabnormal noise, we...

Special Operating Condition Log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D A...

EXCEPTIONS Normal vehicle axle maintenance: Rear axles and power take-off (PTO) units with synthetic fluid and light-duty trucks equipped withFord-design axles are lubricated for life; do not check or change fluidunless a leak is suspected, service is required or the assembly has beensubmerged in wa...

ENGINE COOLANT CHANGE RECORD Initial change Six years or 105000 miles (168000 km)(whichever comes first) After initial change Every three years or 45000 miles (72000 km) Engine Coolant Change Log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C O...

GENERAL INFORMATION Ensure that you review your device’s user guide before using it withSYNC. Support The SYNC support team is available to help you with any questions youcannot answer on your own. Monday-Saturday, 8:30am-8:00pm EST In the United States, call: 1–888–270–1055 In Canada, call: 1–800–5...

When using SYNC, do not: • Operate playing devices if the power cords or cables are broken, splitor damaged. Carefully place cords and cables where they cannot bestepped on or interfere with the operation of pedals, seats,compartments or safe driving abilities. • Leave playing devices in the vehicle...

Phone Options during an Active Call During an active call, you have additional menu features which becomeavailable such as putting a call on hold, joining calls, etc. Use the arrowbuttons to scroll through the menu options. To access:1. Press MENU during an active call.2. When Active Call Menu is se...

When you select: You can: Call History Access your call history log.1. Press OK to select, then scroll through yourcall history options (incoming, outgoing ormissed).2. Press OK when the desired selection appearsin the display.3. Press the phone button to call the selection. Return Exit the current ...

Text Messaging Note: This is a phone-dependent feature. SYNC allows you to receive, send, download and delete text messages.The system can also read incoming text messages to you so that you donot have to take your eyes off the road. Receiving a Text Message Note: This is a phone-dependent feature. ...

Download Unread Msgs allows you to download your unread messages (only) to SYNC. To download the messages, press OK to select. Thedisplay indicates your messages are being downloaded. When complete,SYNC takes you to your inbox. Delete All Messages? allows you to delete current text messages from SYN...

Pre-defined text message options I need more directions I love you Too funny Can’t wait to see you I’m stuck in traffic Accessing Your Phone Settings These are phone-dependent features. Your phone settings allow you toaccess and adjust features such as your ring tone, text messagenotification, modif...

When you select: You can: Modify Phonebook Modify the contents of your phone book (i.e.,add, delete, download). Press OK to select andscroll between: Add Contacts: Press OK to add more contactsfrom your phone book. Push the desiredcontact(s) on your phone. See your phone’suser guide on how to push c...

System Settings System Settings provide access to your Bluetooth Devices andAdvanced menu features. Use the arrow buttons to scroll through themenu options. The Bluetooth Devices menu allows you to add, connect, delete and set aphone as primary as well as turn your Bluetooth feature on and off. The ...

If you select: You can: Set Bluetooth On/Off Turn the Bluetooth feature on and off.Press OK and scroll to toggle between On andOff. When the desired selection is chosen,press OK. Note: Turning Bluetooth off disconnects all Bluetooth devices and deactivates allBluetooth features. Delete Device Delete...

SYNC APPLICATIONS AND SERVICES (IF EQUIPPED) Note: In order for the following features to work, your cellular phone must be compatible with SYNC. To check your phone’s compatibility, visitwww.SYNCMyRide.com, www.SYNCMyRide.ca or www.syncmaroute.ca. • SYNC Services (if equipped, U.S. only): Provides ...

Vehicle Health Report WARNING: Always follow scheduled maintenance instructions, regularly inspect your vehicle, and seek repair for any damage or problem you suspect. Vehicle Health Report supplements, but cannotreplace normal maintenance and vehicle inspection. Vehicle HealthReport only monitors c...

To run a report using the phone button:1. Press the phone button to enter Phone Menu.2. Scroll until Vehicle Health is selected and press OK.3. Scroll to select from the following options: Vehicle Health Report Options User Preferences:Press OK to selectand enter the menu.Scroll to select from: Auto...

Disconnecting from SYNC Services 1. Press and hold the phone button on the steering wheel.2. Say “Good-bye” from the SYNC Services main menu. SYNC Services Quick Tips Personalizing You can personalize your Services feature toprovide quicker access to your most used orfavorite information. You can sa...

“USB” “Search song <name>” 1 “Search track <name>” 1,3 “Shuffle off” “Shuffle on” “Similar music” “What’s playing?” 1 “<name>” is a dynamic listing, meaning that it could be the name of any desired group, artist, etc. 2 Voice commands which are only available in folder mode. 3 Voic...

Voice Command Guide “Refine” This allows you to make your previouscommand more specific. For example, if youasked to search and play all music by acertain artist, you could then say “refinealbum” and choose a specific album from thelist to view. If you then select Play, the systemonly plays music fr...

When you select: You can: Select Source SYNC USB: Press OK to access music plugged into your USB port. You can also plugin devices to charge them (if supported byyour device). Once connected, the systemindexes any readable media files. (The timerequired to complete this depends on the sizeof the med...

When you select: You can: Explore USB Explore all supported digital media on yourmedia device connected to the USB port. Youcan only view media content which iscompatible with SYNC; other files saved arenot visible.Press OK to select. Then scroll to exploreindexed media on your flash drive. Similar ...

Advanced Menu Options This menu allows you to access settings such as prompts, language,performing a master reset as well as returning to factory defaults.1. Press AUX and then MENU to access the Media Menu.2. Scroll until System Settings appears and select OK.3. Scroll until Advanced appears.4. Pre...

When you select: You can: Master Reset Completely erase all information stored onSYNC (all phonebook, call history, textmessages and all paired devices) and returnto the factory default settings. Application Download new software applications (ifavailable) and then load the desiredapplications throu...

Vehicle Health Report/Services (Traffic, Directions and Information) Issues Issue Possible Cause(s) Possible Solution(s) I received a textthat the VehicleHealth Report isnot activated. • Your account may not beactivated on thewebsite, OR • You may have the wrong VIN(vehicleidentificationnumber) list...

NAVIGATION CONTROLS WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that maytake their focus off the road. Your primary responsibility is the safeoperation of the ...

M. SOUND: • Access the sound menu. • Press while the sound menu is active to see the menu tabs ofBass/Treble, Balance/Fade, SCV (Speed Compensated Volume), DSP(Digital Signal Processing) and Visualizer. N. MEDIA: • Press to access the media menu. • Press while the media menu is active to see the ava...

STATUS BARS The top status bar shows thecurrent mode, exterior temperature,time and display icons if you haveenabled Bluetooth or other options. The bottom status bar shows theHome icon and may also show theArtist and Title of the currentlyplaying CD, Artist and Title forJukebox and radio. Customizi...

To load photos:1. Touch the left side of the home screen.2. Select Add. When the disclaimer appears asking to confirm the supported photo formats, press OK. 3. Insert a CD-ROM which contains your photos.4. Press OK. The photos are listed on the right half of the screen.5. Select either Add or Add Al...

Helpful Hints • Make sure the interior of the vehicle is as quiet as possible. Windnoise from open windows and road vibrations may prevent the systemfrom correctly recognizing spoken commands. • After pressing the voice icon, wait until after the tone sounds andListening appears before saying a comm...

SYSTEM MENU FEATURES Your system offers many menu features, such as allowing you to adjustthe touchscreen brightness, time and language, feedback and systemsettings. You can access these options by pressing the MENU hardbutton. If you select: You can: Display Brightness allows you to adjust screen b...

ENTERTAINMENT Your system offers many media options. You can access these optionsusing the touchscreen or voice commands. AM/FM Radio Press the RADIO hard button. To change between AM and FM1/FM2, touch the AM or FM tab. When you select: You can: Show Options Scan allows you to hear a brief sampling...

When you select: You can: Show Presets View the preset stations. To save a station,press and hold one of the memory presethard buttons or memory preset areas on thetouchscreen. There is a brief mute while thestation is being saved, then sound returnswhen it is done. Set PTY/All Select a category of ...

HD Radio™ Information (If Available) Note: HD Radio broadcasts are not available in all markets. HD Radio technology is the digital evolution of analog AM/FM radio. Yoursystem has a special receiver which allows it to receive digital broadcasts(where available) in addition to the analog broadcasts i...

When you select: You can: Tune Go up and down the frequency in individualincrements.If the current station has multiple digitalbroadcasts, the multicast indicator appears.Press Tune repeatedly to advance through allavailable broadcasts. If you are on the lastbroadcast channel, press to advance to th...

HD Radio Reception and Station Troubleshooting Potential Reception Issues Reception area If you are listening to a multicast station andyou are on the fringe of the reception area,the station may mute due to weak signalstrength.If you are listening to HD1, the systemswitches back to the analog broad...

HD Radio Voice Commands If you are listening to the radio, press the voice button on thesteering wheel control. When prompted, say any of thecommands in the following chart. If you are not listening to the radio, press the voice button and, after thetone, say “Radio”, then any of the commands in the...

SIRIUS 姞 Satellite Radio Voice Commands If you are listening to SIRIUS satellite radio, press the voicebutton on the steering wheel control. When prompted, say anyof the commands in the following chart. If you are not listening to SIRIUS satellite radio, press the voice buttonand, after the tone, sa...

SIRIUS 姞 Information Note: SIRIUS reserves the unrestricted right to change, rearrange, add or delete programming including canceling, moving or adding particularchannels, and its prices, at any time, with or without notice to you. FordMotor Company shall not be responsible for any such programming ...

SIRIUS troubleshooting tips Radio Display Condition Possible Action Acquiring Radio requires more thantwo seconds to produceaudio for the selectedchannel. None. This messageshould disappear shortly. Sat Fault/SIRIUSsystem failure Internal module orsystem failure present. If this message does notclea...

CD Press the MEDIA hard button, then select the CD tab on thetouchscreen. If there is no disc in the system, NO DISC appearsin the status bar and you cannot access the CD screen. Once a disc is loaded, you can choose from Scan, Compress, Repeat,Shuffle, Track List and Record. When you select: You ca...

MP3 Press the MEDIA hard button, then select the CD tab on thetouchscreen. If there is no disc in the system, NO DISC appearsin the status bar and you cannot access the CD screen. Once a disc is loaded, you can choose from Scan, Compress, Repeat,Shuffle, Folder Mode and Folder List. When you select:...

Disc Voice Commands If you are listening to or watching a disc, press the voice buttonon the steering wheel control. When prompted, say any of thecommands in the following chart. If you are not listening to or watching a disc, press the voice button and,after the tone, say “Disc”, then any of the co...

Video CD Voice Commands If you are watching a video CD, press the voice button on thesteering wheel control. When prompted, say any of thecommands in the following chart. If you are not watching a video CD, press the voice button and, after thetone, say “Video CD”, then any of the commands in the fo...

Accessing the Music in Your Jukebox Once you have saved music to your jukebox, you can then choosedifferent ways to play the music.1. Press the MEDIA hard button on the navigation system.2. Select the Jukebox tab on the touchscreen. You can then select from the following options: When you select: Yo...

Creating a Playlist Press the MEDIA hard button, then select the Jukebox tab on thetouchscreen.1. Select Options.2. Select Edit Playlists, then which playlist you would like to create.3. Select which category you would like to access from your saved music.4. Select the desired songs and then press A...

User Device If your vehicle is equipped with SYNC 威 , there is a User Device tab. For more information, see the SYNC 威 chapter. Line In (Auxiliary Input Jack) Your vehicle is equipped with an audio input jack which allows a portableaudio device to be plugged into your vehicle’s audio system. To turn...

Press the I (information) button, then select Sirius Travel Link.Choose from any of the following services: When you select: You can: Traffic On Route Identify traffic incidents on your route, nearbyyour vehicle’s current location or near any ofyour favorite places (if programmed). Traffic Nearby My...

SOUND The sound menu allows you to access and adjust settings, such as Bass,Treble, Fade, Balance, Speed Compensated Volume (SCV) and thevisualizer. Press the SOUND hard button. When you select: You can: Bass/Treble Increase or decrease levels by pressing + or -. Balance/Fade Adjust the sound betwee...

When you select: You can: Traffic Preferences Have the system color code roads accordingto speed of traffic flow or add special icons tothe map for things such as road work,accidents, etc.You can also choose to receive traffic alerts. * NavigationPreferences Access and adjust guidance prompts, avera...

Map Icons Vehicle mark shows the current location of the vehicle. It stays in the center of the map display, except when in scroll mode. Scroll cursor allows you to scroll the map; the icon is fixed in the center of the screen. The map position closest to the cursoris in a window on the top center p...

No GPS symbol indicates that insufficient GPS satellite signals are available for accurate map positioning. This icon may beintermittently displayed under normal operation in an area with poor GPS access. Quick-touch Buttons When in map mode, touch anywhere on the map display to access thefollowing ...

Troubleshooting Symptoms Possible Cause Action Focus error. System unable to playreproduced disc. Contact your dealer. Bad disc. Disc was insertedupside down or thesystem is unable toread the informationon the disc. The systemautomatically ejectsthe disc. Track error. The system is unableto reproduc...

GENERAL INFORMATION SYNC 姞 End User License Agreement (EULA) • You have acquired a device (“DEVICE”) that includes software licensed by FORD MOTOR COMPANY from an affiliate of MicrosoftCorporation (“MS”). Those installed software products of MS origin, aswell as associated media, printed materials, ...

SOFTWARE’s ability to use WMDRM to play or copy protectedcontent. This action does not affect unprotected content. When yourDEVICE downloads licenses for protected content, you agree thatMicrosoft may include a revocation list with the licenses. Contentowners may require you to upgrade the SOFTWARE ...

property rights in and to the content which may be accessed through useof the SOFTWARE is the property of the respective content owner andmay be protected by applicable copyright or other intellectual propertylaws and treaties. This EULA grants you no rights to use such content.All rights not specif...

End user notice Microsoft 姞 Windows 姞 Mobile for Automotive Important Safety Information This system Ford SYNC™ contains software that is licensed toManufacturer FORD MOTOR COMPANY by an affiliate of MicrosoftCorporation pursuant to a license agreement. Any removal, reproduction,reverse engineering ...

device. If you desire to withdraw your consent to receive Noticeselectronically, you must discontinue your use of the TeleNav Software.8.4 TeleNav’s or your failure to require performance of any provision shallnot affect that party’s right to require performance at any time thereafter,nor shall a wa...

If the Contracting Officer, federal government agency, or any federalofficial refuses to use the legend provided herein, the ContractingOfficer, federal government agency, or any federal official must notifyNAVTEQ prior to seeking additional or alternative rights in the Data. Wi-Fi hotspot data prov...

911 Assist™ ..............................404 A ABS (see Brakes) .....................225 Accessing call history/phonebook during active call .............394 Accessing the help screen .......463 Accessing the music inyour jukebox .....................457–458 Accessing your media menufeatures .........

Troubleshooting ................142, 472 Turn signal ..................................84 U Universal garage door opener ..179 USB port ....................................124 Using privacy mode ..................394 V Vehicle health report ................407 Vehicle Identification Number(VIN) .......