Ford 2013 Edge v.4- User Manual

Symbol Description Symbol Description Symbol Description Heated rearwindow Interiorluggagecompartmentrelease Jack Lightingcontrol Low tirepressurewarning Maintaincorrect fluidlevel Panic alarm Parking aidsystem Parkingbrake system Powersteering fluid Powerwindowsfront andrear Powerwindowlockout Serv...

Note: Including to the extent that any law pertaining to Event DataRecorders applies to SYNC® or its features, please note thefollowing: Once 911 Assist (if equipped) is enabled (set ON), 911Assist may, through any paired and connected cell phone, discloseto emergency services that the vehicle has b...

FORD CREDIT (U.S. ONLY) Ford Credit offers a full range of financing and lease plans to help youacquire your vehicle. If you have financed or leased your vehicle throughFord Credit, thank you for your business. For your convenience, we offer a number of ways to contact us, as wellas help manage your...

SPECIAL NOTICES New Vehicle Limited Warranty For a detailed description of what is covered and what is not covered byyour vehicle’s New Vehicle Limited Warranty, see the warrantyinformation that is provided to you along with your owner’s manual. Special Instructions For your added safety, your vehic...

GENERAL INFORMATION See the following sections for directions on how to properly use safetyrestraints for children. WARNING: Always make sure your child is secured properly in a device that is appropriate for their height, age and weight. Child safety restraints must be bought separately from your v...

Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommendedrestraint type Infantsortoddlers Children weighing 40 lb (18 kg) orless (generally age four or younger). Use a child safety seat(sometimes called aninfant carrier,convertible seat, ortoddler seat). Small...

Note: The child seat must rest tightly against the vehicle seat upon which it is installed. It may be necessary to lift or remove the headrestraint. See the Seats chapter for information on head restraints. BOOSTER SEATS WARNING: Never place, or allow a child to place, the shoulder belt under a chil...

Types of Booster Seats • Backless booster seats If your backless booster seat has a removable shield, remove the shield.If a vehicle seating position has a low seat back or no head restraint, abackless booster seat may place your child’s head (as measured at thetops of the ears) above the top of the...

4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear a snap and feel the latchengage. Make sure the tongue islatched securely by pulling on it. 5. To put the retractor in theautomatic locking mode, grasp...

This is necessary to remove the remaining slack that will exist once theextra weight of the child is added to the child restraint. It also helps toachieve the proper snugness of the child seat to your vehicle.Sometimes, a slight lean toward the buckle will additionally help toremove remaining slack ...

The LATCH system is composed of three vehicle anchor points: twolower anchors located where your vehicle seatback and seat cushionmeet (called the seat bight) and one top tether anchor located behindthat seating position. LATCH compatible child safety seats have two rigid or webbing mountedattachmen...

Use of Inboard Lower Anchors from the Outboard SeatingPositions (Center Seating Use) WARNING: The standardized spacing for LATCH lower anchors is 11 inches (28 centimeters) center to center. Do not use LATCH lower anchors for the center seating position unless the childseat manufacturer’s instructio...

3. Pull the gap cover reward toexpose the anchors. Clip the tetherstrap to the anchor as shown. 4. Tighten the child safety seat tether strap according to themanufacturer’s instructions. If your child restraint system is equipped with a tether strap, and thechild restraint manufacturer recommends it...

PRINCIPLES OF OPERATION WARNING: Never let a passenger hold a child on his or her lap while your vehicle is moving. The passenger cannot protect the child from injury in a crash. WARNING: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a crash, people riding in ...

FASTENING THE SAFETY BELTS The front outboard and rear safety restraints in your vehicle arecombination lap and shoulder belts. 1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until you hear a snap and feelit latch. Make sure the tongue i...

To adjust the comfort guide: 1. Slip the shoulder belt into thebelt guide. 2. Slide the guide up or down alongthe webbing so that the belt iscentered on the occupant’sshoulder. Restraint of Pregnant Women WARNING: Always ride and drive with your seatback upright and the safety belt properly fastened...

How to Use the Automatic Locking Mode 1. Buckle the combination lap and shoulderbelt. 2. Grasp the shoulder portion and pulldownward until the entire belt is pulled out. 3. Allow the belt to retract. As the beltretracts, you will hear a clicking sound. Thisindicates the safety belt is now in theauto...

Adjust the height of the shoulder belt so thebelt rests across the middle of your shoulder. To adjust the shoulder belt height: 1. Pull on the center button and slide the height adjuster up or down. 2. Release the button and pull down on the height adjuster to make sureit is locked in place. SAFETY ...

Deactivating and Activating the Belt-Minder® Feature WARNING: While the system allows you to deactivate it, this system is designed to improve your chances of being safely belted and surviving an accident. We recommend you leave the systemactivated for yourself and others who may use the vehicle. To...

One-time Belt-Minder® Disable If at any time the driver or front passenger quickly buckles thenunbuckles the safety belt for that seating position, the system is disabledfor the current ignition cycle. The feature will enable during the sameignition cycle if the occupant buckles and remains buckled ...

PERSONAL SAFETY SYSTEM™ The Personal Safety System provides an improved overall level of frontalcrash protection to front seat occupants and is designed to help furtherreduce the risk of airbag-related injuries. The system is able to analyzedifferent occupant conditions and crash severity before act...

The airbags are a supplemental restraint system and are designed towork with the safety belts to help protect the driver and right frontpassenger from certain upper body injuries. Airbags do not inflate slowly;there is a risk of injury from a deploying airbag. Note: You will hear a loud bang and see...

DRIVER AND PASSENGER AIRBAGS WARNING: Never place your arm or any objects over an airbag module. Placing your arm over a deploying airbag can result in serious arm fractures or other injuries. Objects placed on or over theairbag inflation area may cause those objects to be propelled by theairbag int...

Proper Driver and Front Passenger Seating Adjustment WARNING: The National Highway Traffic Safety Administration recommends a minimum distance of at least 10 inches (25 centimeters) between an occupant’s chest and the driver airbagmodule. To properly position yourself away from the airbag: • Move yo...

FRONT PASSENGER SENSING SYSTEM WARNING: Even with Advanced Restraints Systems, children 12 and under should be properly restrained in a rear seating position. Failure to follow this could seriously increase the risk of injuryor death. WARNING: Sitting improperly out of position or with the seat back...

The front passenger sensing systemuses a passenger airbag statusindicator which will illuminateindicating that the front passengerfrontal airbag is either ON(enabled) or OFF (disabled). Theindicator lamp is located in thecenter stack of the instrumentpanel. Note: When the ignition is first turned on...

SIDE AIRBAGS WARNING: Do not place objects or mount equipment on or near the airbag cover, on the side of the seatbacks (of the front seats), or in front seat areas that may come into contact with a deployingairbag. Failure to follow these instructions may increase the risk ofpersonal injury in the ...

The system consists of thefollowing: • a tag on the seatback indicatingthat side airbags are found onyour vehicle • side airbags located inside theseatback of the driver and frontpassenger seats. • crash sensors and monitoring system with readinessindicator. See Crash Sensors and Airbag Indicator la...

Children 12 years old and under should always be properly restrained inthe rear seats. The Safety Canopy will not interfere with childrenrestrained using a properly installed child or booster seat because it isdesigned to inflate downward from the headliner above the doors alongthe side window openi...

If any of these things happen, even intermittently, have the supplementalrestraint system serviced at an authorized dealer immediately. Unlessserviced, the system may not function properly in the event of a crash. The safety belt pretensioners and the airbag supplemental restraintsystem are designed...

PRINCIPLE OF OPERATION The remote control allows you to: • remotely lock or unlock the vehicle doors • unlock the doors without actively using a key or remote control(intelligent access only) • remotely open the power liftgate (if equipped) • remotely start or stop the engine (if equipped) • arm and...

The radio frequency used by your remote control can also be used byother short-distance radio transmissions, for example amateur radios,medical equipment, wireless headphones, remote controls and alarmsystems. If the frequencies are jammed, you will not be able to use yourremote control. You can loc...

Replacing the Battery Note: Refer to local regulations when disposing of transmitter batteries. Note: Do not wipe off any grease on the battery terminals or on the back surface of the circuit board. Note: Replacing the battery will not delete the transmitter from your vehicle. The transmitter should...

3. Remove the old battery. 4. Insert a new battery with the + facing downward. Press the battery down to make sure it is fully in the housing. 5. Snap the battery cover back onto the transmitter and install thebackup key. Memory Feature (If Equipped) This feature allows you to recall the driver seat...

Deactivating from the Remote Control 1. Press and hold the desired memory button for five seconds. A tonewill sound after about two seconds. Continue to hold until you hear asecond tone. 2. Press the unlock button on the remote control within three seconds. Repeat this procedure for each additional ...

Extending the Vehicle Run Time Repeat Steps 1 and 2 with your vehicle still running to extend the runtime for another remote start duration. If the duration is set to last10 minutes, the duration will extend by another 10 minutes beginningafter what is left of the first activation time. For example,...

PRINCIPLES OF OPERATION MyKey allows you to program keys with restricted driving modes topromote good driving habits. All but one of the keys programmed to thevehicle can be activated with these restricted modes. Any keys that have not been programmed are referred to asadministrator keys or admin ke...

• Vehicle speed minders of 45, 55 or 65 mph (75, 90 or 105 km/h). Onceyou select a speed, it will be shown in the display, followed by anaudible tone when the preselected vehicle speed is exceeded. • Audio system maximum volume of 45%. A message will be shown inthe display when you attempt to exceed...

USING MYKEY WITH REMOTE START SYSTEMS MyKey is not compatible with non-Ford-approved aftermarket remotestart systems. If you choose to install a remote start system, please seeyour Ford authorized dealer for a Ford-approved remote start system . Vehicles With Ford-approved Aftermarket Remote Start S...

Vehicles With Non-Ford-approved Aftermarket Remote StartSystems MyKey is not compatible with non-Ford-approved aftermarket remotestart systems. If you choose to install a remote start system, please see aFord authorized dealer for a Ford-approved system. The following information may help customers ...

LOCKING AND UNLOCKING You can use the power door lock control or the remote control to lockand unlock your vehicle. Power Door Locks The power door lock control is located on the driver and front passengerdoor panels. A. Unlock B. Lock Remote Control You can use the remote control anytime your vehic...

Note: If any door or the luggage compartment is open, or if the hood is open on vehicles with an anti-theft alarm or remote start, the hornsounds twice and the lamps will not flash. Power Liftgate (If Equipped) WARNING: Make sure all persons are clear of the liftgate area before using power liftgate...

At the Liftgate Press the exterior liftgate release button on the top of the liftgatepull-cup handle. Smart Unlocks for Integrated Keyhead Transmitter This feature helps to prevent you from locking yourself out of yourvehicle if your key is still in the ignition. When you open one of the front doors...

Autolock Feature (If Enabled) The autolock feature will lock all the doors when: • all the doors are closed, • the ignition is on, • you shift into any gear putting your vehicle in motion, and • your vehicle reaches a speed greater than 12 mph (20 km/h). The autolock feature repeats when: • you open...

Note: Cycling the ignition while the liftgate is power closing and is near the latch may cause the liftgate to reverse to full open position. Makesure you close the liftgate before operating or moving the vehicle,especially in an enclosure, like a garage or a parking structure. You coulddamage the l...

To open with the outside liftgatecontrol button: 1. Unlock the liftgate with the remotecontrol or power door unlock button.If an intelligent access transmitter iswithin 3 feet (1 meter) of the liftgate,the liftgate will unlock when youpress the liftgate release button. 2. Press the control button lo...

To reset the power liftgate: 1. Disconnect the battery for 20 seconds then, reconnect the battery. 2. Manually close and fully latch the liftgate. 3. Power open the liftgate by using the remote control or the instrumentpanel button. SECURICODE™ KEYLESS ENTRY KEYPAD (IF EQUIPPED) You can use the keyp...

Tips: • Do not set a code that uses five of the same number. • Do not use five numbers in sequential order. • The factory-set code will work even if you have set your own personalcode. Erasing a Personal Code 1. Enter the factory-set 5-digit code. 2. Press and release 1 • 2 on the keypad within five...

5. Press and release the brake pedal one time. The indicator on the START/STOP button should begin to rapidly flash, indicating the programming mode has been entered and two programmed intelligentaccess keys have been detected in the vehicle. 6. Press the START/STOP button within one minute. A messa...

Disarming the Alarm To disarm the alarm, do any of the following: • Press the power door unlock button within the 20-second pre-armedmode. • Press the unlock button on the remote control. • Unlock the doors with the keyless entry pad. • Enter the vehicle using intelligent access (if equipped). • Tur...

ADJUSTING THE STEERING WHEEL WARNING: Do not adjust the steering wheel when your vehicle is moving. Note: Make sure that you are sitting in the correct position. See Sitting in the Correct Position in the Seats chapter. 1. Unlock the steering column. 2. Adjust the steering wheel to thedesired positi...

VOICE CONTROL (IF EQUIPPED) A. Phone mode B. Voice recognition See the SYNC or MyFord Touch chapter. CRUISE CONTROL Type 1 Type 2 See the Cruise Control chapter for information on this feature. SEEK VOL A B SET RES CNCL ON OFF GAP Steering Wheel 87 2013 Edge (edg) Owners Guide gf, 4th Printing, Nove...

INFORMATION DISPLAY CONTROL See the Information Displays chapter for more information. Cluster Display Control Features If equipped with: MyFord system: This control functions the same as the centercontrol on the faceplate. See MyFord system in the Audio Systems chapter. MyFord Touch: Use this contr...

WINDSHIELD WIPERS Note: Fully defrost the windshield in icy conditions before turning on the windshield wipers. Note: Make sure the windshield wipers are switched off before entering a car wash. Note: Clean the windshield and wiper blades if they begin to leave streaks or smears. If that does not re...

LIGHTING CONTROL A. Off B. Parking lamps, instrument panellamps, license plate lamps and taillamps C. Headlamps High Beams Push the lever forward to switch thehigh beams on. Push the lever forward again or pullthe lever toward you to switch thehigh beams off. Headlamp Flasher • Pull toward you sligh...

AUTOLAMPS Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the headlamp control. • To turn autolamps on, rotate thecontrol to . • To turn autolamps off, rotate thecontrol from the autolampposition. The aut...

DIRECTION INDICATORS The turn signal lever does not mechanically lock in the upward ordownward position when activated. The turn signal control activation andcancellation is electronic. • Push down to activate the left turnsignal. • Push up to activate the right turnsignal. • Push the lever again in...

Map/dome lamp (if equipped) The dome lamp lights when: • any door is opened. • the dome lamp button on theinstrument panel is activated. • any of the remote entry controlsare pressed and the ignition is off. The map lamps are activated by pressing the controls on either side ofthe lens. Rear courtes...

POWER WINDOWS WARNING: Do not leave children unattended in your vehicle and do not let children play with the power windows. They may seriously injure themselves. WARNING: When closing the power windows, you should verify they are free of obstructions and make sure that children and pets are not in ...

Pull up the window switch and hold within two seconds of the windowreaching the bounce-back position. The window will travel up with nobounce-back protection. The window will stop if you release the switchbefore the window is fully closed. Accessory Delay You can use the window switches for several ...

Foldaway Exterior Mirrors Push the mirror toward the door window glass. Make sure that you fullyengage the mirror in its support when returning it to its original position. Memory Mirrors (If Equipped) You can save and recall the mirror positions through the memoryfunction. See Memory function in th...

The image of the approachingvehicle is small and near the inboardedge of the main mirror when it is ata distance. The image becomeslarger and begins to move outboardacross the main mirror as the vehicleapproaches (A). The image willtransition from the main mirror andbegin to appear in the blind spot...

Note: Do not attempt to move the sunshades manually or sunshade damage or malfunction may occur. The sunshade track clips are designedto release the sunshade crossbar in order to prevent damage to thesystem. If this occurs the sunshade crossbar ends may just need to beslid back into position to rega...

Closing the Moonroof and Sunshades Note: The sunshades will only close after the moonroof is completely closed. Pull and release the control. Themoonroof will stop short of the fullyclosed position. Pull the controlagain and hold to fully close themoonroof. Pull and release the control to close the ...

GAUGES Type 1 Cluster shown in standard measure – metric clusters similar. A. Tachometer B. Information display. See Information displays for more information. C. Speedometer D. Fuel gauge Fuel Gauge Indicates approximately how much fuel is left in the fuel tank (when theignition is on). The fuel ga...

Type 2 Cluster shown in standard measure – metric clusters similar. A. Left information display. See Information displays for more information. B. Speedometer C. Right information display. See MyFord Touch® for more information. WARNING LAMPS AND INDICATORS These lights can alert you to a vehicle co...

Adaptive cruise control (if equipped) (RTT) The speed control system indicator light changes color to indicate whatmode the system is in: • On (gray light): Illuminates when the adaptive cruise control system isturned on. Turns off when the speed control system is turned off. • Engaged (green light)...

WARNING: Driving a vehicle with the brake system warning light on is dangerous. A significant decrease in braking performance may occur. It will take you longer to stop the vehicle.Have the vehicle checked by your authorized dealer as soon as possible.Driving extended distances with the parking brak...

Grade assist (if equipped) (RTT) Illuminates when grade assist is turned on. Heads up display (if equipped) A red beam of lights will illuminate on the windshield in certaininstances when using adaptive cruise control and/or thecollision warning system. It will also illuminate momentarily when you s...

Safety belt Reminds you to fasten your safety belt. A Belt-Minder® chimewill also sound to remind you to fasten your safety belt. Service engine soon The service engine soon indicator light illuminates when the ignition is first turned to the on position to check the bulb andto indicate whether the ...

GENERAL INFORMATION WARNING: Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus offthe road. Your primary responsibility is the safe operation of yourvehicle. We recommend...

†Trip 1 / 2 Trip Odometer Trip Timer Distance to E Inst Fuel Econ Average Fuel Fuel Used Compass (located in lower line of display). Note: this will also display in other menus. Total Odometer (located in lower line of display). Note: this will also display in other menus. †See Trip computer later i...

Settings Driver Assist Traction Control Blind Spot Collision Warning Sensitivity High, Normal orLow Chimes (not selectable if using aMyKey) Warning (not selectable if using aMyKey) Cross Traffic Rear Park Aid Trailer Sway Display Language English, Español or Français Units Distance Miles andGallons ...

Settings MyKey Create MyKey Hold OK to Create MyKey 911 Assist Always On / User Selectable Traction Control Always On or User Selectable Max Speed 80 MPH (130 km/h) or Off Speed Warning 45 mph (75 km/h), 55 mph(90 km/h), 65 mph (105 km/h) orOff Volume Limiter Clear MyKeys Hold OK to Clear MyKeys Sys...

Total Odometer Registers the total mileage of the vehicle. Compass (non MyFord/MyLincoln Touch units only) Displays the vehicle’s heading direction.To calibrate the compass: Enter the compass menu and select Calibrate.Follow the prompts.To set the compass zone: Enter the compass menu and select Set....

Main menu From the main menu bar on the left side of the information display, youcan choose from the following categories: Display Mode Trip 1 & 2 Fuel Economy Settings Information Scroll up/down to highlight one of the categories, then press the rightarrow key or OK to enter into that category....

Fuel Economy Use the left/right arrow buttons to choose the desired fueleconomy display. Fuel Economy Inst. Fuel Economy XX. Min Fuel History Instantaneous fuel usage x †Fuel usage over a 5, 10, or30 minute time span x Total odometer (lower left corner) Press and hold OK to reset the currently displ...

Vehicle Autolamp Delay Off or number of seconds Easy Entry/Exit On / Off Fuel DTE Calculation Normal, Towing Locks Autolock, On / Off Autounlock On / Off Remote Unlocking All doors / Driver’s door Menu Control Standard / Memory On (See Menu control later in this section) Oil Life Reset Set to XXX % ...

Menu control To change the menu control between Standard or Memory On, refer to Vehicle > Menu Control found in the table under Settings in this chapter. • Standard: when in the Display, Trip or Fuel Economy sub-categories,scrolling up and down will always exit back to the main categories. • Memo...

AdvanceTrac® / Traction Control Messages Action / Description Service AdvanceTrac Displayed when the AdvanceTrac® system hasdetected a condition that requires service.Contact your authorized dealer as soon aspossible. Traction control off Displayed when the traction control has beendisabled by the d...

AWD Messages Action / Description AWD Off Displayed when the AWD system has beenautomatically disabled to protect itself. This iscaused by operating the vehicle with thecompact spare tire installed or if the system isoverheating. The AWD system will resumenormal function and clear this message after...

Brake System Messages Action / Description Park Brake Engaged Displayed when the parking brake is set, theengine is running and the vehicle is drivenmore than 3 mph (5 km/h). If the warningstays on after the parking brake is released,contact your authorized dealer as soon aspossible. Collision Warni...

Keys and Intelligent Access Messages Action / Description Starting System Fault This message is displayed when there is aproblem with your vehicle’s starting system.See your authorized dealer for service. Maintenance Messages Action / Description LOW Engine OilPressure Stop the vehicle as soon as sa...

Passenger Sensing System Message Action / Description Remove Objects NearPassenger Seat Displayed when objects are by the passengerseat. After the objects are moved away fromthe seat, if the warning stays on or continuesto come on contact your authorized dealer assoon as possible. Reminder Messages ...

GENERAL INFORMATION Radio Frequencies and Reception Factors AM and FM frequencies are established by the Federal CommunicationsCommission (FCC) and the Canadian Radio and TelecommunicationsCommission (CRTC). Those frequencies are: AM: 530, 540–1700, 1710 kHz FM: 87.9–107.7, 107.9 MHz Radio reception...

MP3 Track and Folder Structure Audio systems capable of recognizing and playing MP3 individual tracksand folder structures work as follows: • There are two different modes for MP3 disc playback: MP3 trackmode (system default) and MP3 folder mode. • MP3 track mode ignores any folder structure on the ...

MyFord® SYSTEM WARNING: Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus offthe road. Your primary responsibility is the safe operation of yourvehicle. We recommend agai...

C. Memory presets: • In radio mode, store your favorite radio stations. To store a radiostation, tune to the station, then press and hold a preset button untilsound returns. • In CD mode, press one of these buttons to select a track. D. Function buttons: Select different functions of the audio syste...

M. PHONE: Press this button to access the phone features of the SYNC system. See the SYNC chapter for more information. N. AUX: Press this button to access your auxiliary input jack or switch between devices you plug into the input jack or USB port. See Auxiliary input jack later in this chapter. O....

SIRIUS Channel Guide Select to view available satellite radiochannels. Press OK to open a list of the following options for this channel: TuneChannel, Skip Channel or Lock Channel. Onceyou skip or lock a channel, you can only accessit by pressing Direct and entering the channelnumber. Locking or unl...

AM/FM/CD SONY® AUDIO SYSTEM (IF EQUIPPED) WARNING: Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus offthe road. Your primary responsibility is the safe operation of you...

The auxiliary input jack allows you to connect and play music from yourportable music player through your vehicle speakers. You can use anyportable music player designed for use with headphones. Your audioextension cable must have male 1 ⁄ 8 -inch (3.5 millimeter) connectors at each end.1. Switch of...

MEDIA HUB (IF EQUIPPED) The media hub is located in the center console and has the followingfeatures: A. A/V inputs B. SD card slot C. USB ports For more information, see the MyFord Touch chapter. SATELLITE RADIO INFORMATION (IF EQUIPPED) Satellite Radio Channels Sirius broadcasts a variety of music...

Radio display Condition Possible action Call SIRIUS1–888–539–7474 Your satellite service isno longer available. Call Sirius at1–888–539–7474 toresolve subscriptionissues. None Found. CheckChannel Guide. All the channels in theselected category areeither skipped orlocked. Use the channel guideto turn...

MANUAL HEATING AND AIR CONDITIONING SYSTEM A. Fan speed control: Controls the volume of air circulated in your vehicle. Turn to select the desired fan speed or switch off. If you switchthe fan off, the windshield may fog up. B. Defrost: Distributes air through the windshield defroster vents and demi...

H. Air distribution control: Press to set the air distribution to a position listed below: Distributes air through the windshield defroster vents, demistervents and floor vents. Distributes air through the instrument panel vents. Distributes air through the instrument panel vents, floor vents,and de...

F. A/C: Press to turn air conditioning off and on. Air conditioning cools the vehicle using outside air. To improve air conditioning when startingyour vehicle, drive with the windows slightly open for two to threeminutes.Use air conditioning with recirculated air to improve cooling performanceand ef...

During extreme high ambient temperatures when idling stationary forextended periods in gear, run the air conditioning in the MAX A/C mode,adjust the blower fan speed to the lowest setting and put the vehicle’stransmission into position P (automatic transmission) to continue to receive cool air from ...

For maximum cooling performance in AUTO mode, press MAX A/C. For maximum cooling performance in manual override control:1. Choose the Panel, A/C, and recirculated air controls.2. Set the temperature to LO.3. Set the fan to the highest blower setting. To aid in side window defogging and demisting in ...

CABIN AIR FILTER Note: Make sure you have a cabin air filter installed at all times. This prevents foreign objects from entering the system. Running the systemwithout a filter in place could result in degradation or damage to thesystem. Your vehicle is equipped with a cabin air filter, which is loca...

Manual Climate Systems In hot weather, the climate control system is set to MAX A/C. In moderate weather, the system either heats or cools (based onprevious settings). The rear defroster and heated mirrors are notautomatically turned on. In cold weather, maximum heat is provided in floor/defrost mod...

SITTING IN THE CORRECT POSITION WARNING: Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the decision of the passenger sensing system, resulting inserious injury or death in a crash. Always sit upright against your seatba...

B. two steel stems C. guide sleeve unlock and remove button D. guide sleeve adjust and release button • Raise: Pull up on the head restraint (A). • Lower: Press and hold the guide sleeve adjust and release button (D)and push down on the head restraint (A). • Remove: Pull up the head restraint until ...

Tilting Head Restraints (If Equipped) The front head restraints may have a tilting feature for extra comfort. Totilt the head restraint, do the following: 1. Adjust the seatback to an upright driving or ridingposition. 2. Tilt the head restraint forward by gently pullingthe top of the head restraint...

Adjusting the Height of theDriver Seat WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Recline Adjustment WARNING: Cover sharp edges on the load to help prevent injury to occupants. Secure the load to help prevent shifting during sudden stops....

Folding the Front PassengerSeatback The front passenger seatback can be folded to a horizontal position tomake room for a long load. Lumbar Adjustment POWER SEATS (IF EQUIPPED) WARNING: Never adjust the driver’s seat or seatback when the vehicle is moving. WARNING: Before returning the seatback to i...

MEMORY FUNCTION (IF EQUIPPED) The memory control, located on theinstrument panel, allows automaticpositioning of the driver seat andpower mirrors to two programmablepositions. Programming a Memory Position Note: You can program a memory position at any time. • To program position 1, move the memory ...

REAR SEATS WARNING: To prevent possible damage to the seat or safety belts, make sure that the safety belts are not buckled when folding the seatback. • Reclining the seatback: With the seatoccupied, pull the lever up to recline theseatback. • Folding the seatback: With the seat empty,pull the lever...

REAR SEAT ARMREST Press the latch and pull the armrestforward for armrest or cupholder use. Lift up one of the slotted areas on thecover to access the cup holders. To close the armrest, close the cupholder cover and rotate the armrestrearward until the latch clicks. 168 Seats 2013 Edge (edg) Owners ...

HOMELINK® WIRELESS CONTROL SYSTEM (IF EQUIPPED) WARNING: Make sure that the garage door and security device are free from obstruction when you are programming. Do not program the system with the vehicle in the garage. WARNING: Do not use the system with any garage door opener that does not have the ...

6. Return to your car. 7. Press and hold the function button youwant to program for two seconds, thenrelease. Repeat this step. Depending onyour brand of garage door opener, youmay need to repeat this sequence a thirdtime. To program additional buttons, repeat Steps 1 – 4 . For questions or comments...

Programming HomeLink to the Genie Intellicode garage dooropener motor Note: You may need a ladder to access the garage door opener motor. To program HomeLink to the garagedoor opener motor: 1. Press and hold the PROGRAMbutton on the garage door openermotor until both blue LED’s turn on. 2. Release t...

AUXILIARY POWER POINTS Note: Do not insert objects other than an accessory plug into the power point. This will damage the outlet and blow the fuse. Note: Do not hang any type of accessory or accessory bracket from the plug. Note: Improper use of the power outlet can cause damage not covered by your...

CENTER CONSOLE Stow items in the cupholder carefully as items may become loose duringhard braking, acceleration or collisions, including hot drinks which mayspill. Available console features include: A. Cupholders B. Cover: Two pen holders, traveltissue pack holder, and business cardor paper holder....

GENERAL INFORMATION WARNING: Extended idling at high engine speeds can produce very high temperatures in the engine and exhaust system, creating the risk of fire or other damage. WARNING: Do not park, idle, or drive your vehicle on dry grass or other dry ground cover. The emission system heats up th...

A. Off: The ignition is off. B. Accessory: Allows the electrical accessories, such as the radio, to operate while the engine is not running. C. On: All electrical circuits are operational and the warning lamps and indicators illuminate. D. Start: Cranks the engine. KEYLESS STARTING (IF EQUIPPED) Not...

Off: Turns the ignition off. • Without applying the brake pedal, press and release the button oncewhen the ignition is in the on mode, or when the engine is runningbut the vehicle is not in motion. Accessory: Allows some electrical accessories to operate while the engine is not running. • Without ap...

Important Ventilating Information If you stop your vehicle and leave the engine idling for long periods, werecommend that you do one of the following: • Open the windows at least 1 inch (2.5 centimeters). • Set your climate control to outside air. ENGINE BLOCK HEATER (IF EQUIPPED) WARNING: Failure t...

• Make sure the system is unplugged and properly stowed before drivingyour vehicle. Make sure the protective cover seals the prongs of theblock heater cord plug when not in use. • Keep plug terminals clean and free of dirt and corrosion. • Make sure the heater system is checked for proper operation ...

SAFETY PRECAUTIONS WARNING: Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. WARNING: The fuel system may be under pressure. If you hear a hissing sound near the fuel filler inlet, do not refuel until the sound stops. Otherwise, fue...

• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes,remove contact lenses (if worn), flush with water for 15 minutes andseek medical attention. Failure to seek proper medical attention couldlead to permanent injury. • Fuels can also be harmful if absorbed through the skin. If f...

octane levels below 87 are not recommended. Premium fuel will provideimproved performance and is recommended for severe duty usage suchas trailer tow. Do not be concerned if your enginesometimes knocks lightly. However,if it knocks heavily while you areusing fuel with the recommendedoctane rating, s...

When filling the vehicle’s fuel tank from a portable fuel container, use thefunnel included with the vehicle. 1. Locate the white plastic funnel in the spare tirecompartment. 2. Slowly insert the funnel into the capless fuelsystem. 3. Fill the vehicle with fuel from the portable fuelcontainer. 4. Wh...

Easy Fuel® “No Cap” Fuel System WARNING: The fuel system may be under pressure. If you hear a hissing sound near the fuel filler door, do not refuel until the sound stops. Otherwise, fuel may spray out, which could cause seriouspersonal injury. When fueling your vehicle: 1. Turn the engine off. 2. O...

EMISSION CONTROL SYSTEM WARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. WARNING: Exhaust leaks may result in entry of harmful and potentially lethal fumes into th...

AUTOMATIC TRANSMISSION WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the off position and remove the key whenever you leave your vehicle. Your vehicle has been designed to improve fuel economy by reducingfuel usage while coasting...

S (Sport) (if equipped) Moving the gearshift lever to S (Sport mode): • Provides additional grade (engine) braking and extends lower gearoperation to enhance performance for uphill climbs, hilly terrain ormountainous areas. This will increase engine RPM during enginebraking. • Provides additional lo...

If your vehicle is equipped with paddles on the steering wheel: • Pull the left paddle (–) todownshift the transmission. • Pull the right paddle (+) to upshiftthe transmission. Upshift to the recommended shift speeds according to the followingchart: Upshifts when accelerating (recommended for best f...

Brake-shift interlock WARNING: Do not drive your vehicle until you verify that the brake lamps are working. WARNING: When doing this procedure, you will be taking the vehicle out of park which means the vehicle can roll freely. To avoid unwanted vehicle movement, always fully set the parking brakepr...

3. Apply the brake pedal. Gently push and hold the brake shift interlocklever while pulling the gearshift lever out of the P (Park) position andinto the N (Neutral) position. 4. Install the trim panel. 5. Apply the brake pedal, start the vehicle, and release the parkingbrake. Note: See your authoriz...

This feature makes it easier to pull away when the vehicle is on a slopewithout the need to use the parking brake. When this feature is active,the vehicle will remain stationary on the slope for two to three secondsafter you release the brake pedal. This allows you time to move your footfrom the bra...

Maintenance and Modifications The suspension and steering systems on your vehicle have been designedand tested to provide predictable performance whether loaded or emptyand durable load carrying capability. For this reason, Ford MotorCompany strongly recommends that you do not make modifications suc...

GENERAL INFORMATION Note: Occasional brake noise is normal. If a metal-to-metal, continuous grinding or continuous squeal sound is present, the brake linings may beworn out. Have them inspected by an authorized dealer. If your vehiclehas continuous vibration or shudder in the steering wheel while br...

PRINCIPLES OF OPERATION The traction control system helps avoid drive wheel spin and loss oftraction. If your vehicle begins to slide, the system applies the brakes to individualwheels and, when needed, reduces engine power at the same time. If thewheels spin when accelerating on slippery or loose s...

PRINCIPLES OF OPERATION WARNING: Vehicle modifications involving braking system, aftermarket roof racks, suspension, steering system, tire construction or wheel and tire size may change the handlingcharacteristics of the vehicle and may adversely affect the performanceof the AdvanceTrac® system. In ...

A Vehicle without AdvanceTrac® with RSC® skidding off its intendedroute. B Vehicle with AdvanceTrac® with RSC® maintaining control on aslippery surface. USING ADVANCETRAC® WITH RSC® The system automatically activates when you start your engine. TheAdvanceTrac® with RSC® system cannot be completely t...

SENSING SYSTEM (IF EQUIPPED) WARNING: To help avoid personal injury, please read and understand the limitations of the system as contained in this section. Sensing is only an aid for some (generally large and fixed)objects when moving in reverse on a flat surface at parking speeds.Traffic control sy...

If a fault is present in the system, a warning message appears in theinformation display and does not allow the driver to switch the faultedsystem on. Note: If your vehicle is equipped with MyKey®, it is possible to prevent turning the sensing system off. Refer to the MyKey® chapter. Using the Rear ...

Using the Rear View Camera System The rear view camera system displays what is behind your vehicle whenyou place the transmission in R (Reverse). The system uses two types ofguides to help you see what is behind your vehicle:1. Fixed guidelines: Show the actual path the vehicle is moving in while re...

Guidelines and the Centerline Note: Fixed guidelines are only available when the transmission is in R (Reverse). Note: The centerline is only available if fixed guidelines are on. A. Rear bumper B. Fixed guideline: Red zone C. Fixed guideline: Yellow zone D. Fixed guideline: Green zone E. Centerline...

Manual Zoom WARNING: When manual zoom is on, the full area behind the vehicle is not shown. Be aware of your surroundings when using the manual zoom feature. Note: Manual zoom is only available when the transmission is in R (Reverse). Note: When manual zoom is enabled, only the centerline is shown. ...

PRINCIPLES OF OPERATION Cruise control lets you maintain a set speed without keeping your footon the accelerator pedal. USING CRUISE CONTROL WARNING: Do not use cruise control in heavy traffic, on winding roads or when the road surface is slippery. This could result in loss of vehicle control, serio...

WARNING: Do not use in poor visibility, specifically fog, rain, spray or snow. Note: It is your responsibility to stay alert, drive safely and be in control of your vehicle at all times. The system adjusts your speed to maintain a proper distance betweenyou and the vehicle in front of you in the sam...

4. Take your foot off the accelerator pedal. 5. A lead vehicle graphic willilluminate if there is a vehicledetected in front of you. Note: When adaptive cruise control is active, the set speed displayed in the information display may vary slightly from the speedometer. Following a Vehicle WARNING: W...

engine braking in these situations to reduce the load on the vehicle’sregular brake system to prevent them from overheating. Switching Off Adaptive Cruise Control Note: The set speed memory will erase when you switch the system off. Press and release OFF or turn off the ignition. Detection Issues Th...

Cause Action The surface of the radar in thegrille is dirty or obstructed insome way. Clean the grille surface in front ofthe radar or remove the objectcausing the obstruction. The surface of the radar in thegrille is clean but the messageremains in the display. Wait a short time. It may takeseveral...

BLIND SPOT INFORMATION SYSTEM (BLIS®) WITH CROSSTRAFFIC ALERT (CTA) (IF EQUIPPED) WARNING: To help avoid injuries, NEVER use the BLIS® as a replacement for using the interior and exterior mirrors and looking over your shoulder before changing lanes. BLIS® is not areplacement for careful driving and ...

Using the Systems BLIS® turns on when the engine is started and the vehicle is drivenforward above 3 mph (5 km/h); it remains on while the transmission is inD (Drive) and N (Neutral). If shifted out of D (Drive) or N (Neutral),the system enters CTA mode. Once shifted back into D (Drive), BLIS®turns ...

System Lights and Messages The BLIS® and CTA systemsilluminate a yellow alert indicator inthe outside mirror on the side ofthe vehicle the approaching vehicleis coming from. Note: The alert indicator dims when the headlamp switch is not in the off position and nighttime darkness is detected. CTA als...

System Sensors WARNING: Just prior to the system recognizing a blocked condition and alerting the driver, the number of missed objects will increase. To help avoid injuries, NEVER use the BLIS® as areplacement for using the side and rear view mirrors and looking overyour shoulder before changing lan...

If it is, a red warning lightilluminates and an audible warningchime sounds. The brake support system assists the driver in reducing the collisionspeed by charging the brakes. If the risk of collision further increasesafter the warning light illuminates, the brake support prepares the brakesystem fo...

Blocked Sensors If a message regarding a blockedsensor appears in the informationdisplay, the radar signals from thesensor have been obstructed. Thesensors are located behind a fasciacover near the driver side of thelower grille. When the sensors areobstructed, a vehicle ahead cannot bedetected and ...

System Limitations WARNING: The collision warning system’s brake support can only help reduce the speed at which a collision occurs if the driver applies the vehicle’s brakes. The brake pedal must be pressedjust like any typical braking situation. Due to the nature of radar technology, there may be ...

STEERING To help prevent damage to the power steering system: • Never hold the steering wheel at its furthest turning points (until itstops) for more than three to five seconds while the engine is running. • Do not operate the vehicle with a low power steering pump fluidreservoir level (below the MI...

CARGO NETS (IF EQUIPPED) WARNING: This net is not designed to restrain objects during a collision or heavy braking. The cargo net secures lightweight objects in the cargo area. Attach the net to the anchors provided in one of the two configurations.Repeat the attachment on both sides of the vehicle....

ROOF RACKS AND LOAD CARRIERS (IF EQUIPPED) WARNING: When loading the roof racks, we recommend you evenly distribute the load, as well as maintain a low center of gravity. Loaded vehicles, with higher centers of gravity, may handledifferently than unloaded vehicles. Take extra precautions, such asslo...

UTILITY HOOK You can use the utility hook to hangsmall items such as grocery bags.Do not hang more than 10 pounds(4.5 kilograms) on the hook. LOAD LIMIT Vehicle Loading – With and Without a Trailer This section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded v...

Vehicle Curb Weight – is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarketequipment. Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-...

Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loadweight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all pa...

GVWR (Gross Vehicle Weight Rating) – is the maximum allowable weight of the fully loaded vehicle (including all options, equipment,passengers and cargo). The GVWR is shown on the Safety Compliance Certification Label. The label shall be affixed toeither the door hinge pillar, door-latch post, or the...

WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structuraldamage, serious damage to the vehicle, loss of control and personalinjury. GCW (Gross Combined Weight) – is the...

WARNING: Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury. Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.” on your vehicle’s pla...

TOWING A TRAILER WARNING: Do not exceed the GVWR or the GAWR specified on the certification label. WARNING: Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of your vehicle and could result in engine damage, transmission damage, structural damage, lossof vehicle ...

TRAILER SWAY CONTROL (IF EQUIPPED) WARNING: Turning off trailer sway control increases the risk of loss of vehicle control, serious injury or death. Ford does not recommend disabling this feature except in situations where speedreduction may be detrimental (such as hill climbing), the driver hassign...

Powertrain Maximum GCWR Maximum trailer weight 2.0L GTDI front-wheeldrive 6170 lb (2799 kg) 1500 lb (680 kg) 3.5L TiVCT front-wheeldrive * 8210 lb (3724 kg) 2000 lb (907 kg) 3.5L TiVCT front-wheeldrive ** 8210 lb (3724 kg) 3500 lb (1588 kg) 3.5L TiVCT all-wheeldrive * 8400 lb (3810 kg) 2000 lb (907 ...

Trailer Towing Connector (Vehicles Equipped with a Trailer-towingor Prep Package) The trailer towing connector is located under the rear bumper, on theleft side of your vehicle. You must use a four-pin trailer wiring connector foryour vehicle and the trailer lighting equipment. Color Function 1. Dar...

Trailer Brakes WARNING: Do not connect a trailer’s hydraulic brake system directly to your vehicle’s brake system. Your vehicle may not have enough braking power and your chances of having a collision greatlyincrease. Electric brakes and manual, automatic or surge-type trailer brakes aresafe if you ...

TRANSPORTING THE VEHICLE If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. We recommend the use of a wheel lift and dollies or flatbed equipmentto tow your vehicle. Do not t...

Front-wheel drive vehicles must have the front wheels placed on a towdolly when towing your vehicle from the rear using wheel lift equipment.This prevents damage to the transmission. Towing an all-wheel drive vehicle requires that all wheels be off theground, such as using a wheel lift and dollies o...

BREAKING-IN You need to break in new tires for approximately 300 miles(480 kilometers). During this time, your vehicle may exhibit some uniquedriving characteristics. Avoid driving too fast during the first 1000 miles(1600 kilometers). Vary your speed frequently and change up throughthe gears early....

• Add particular accessories to your vehicle (e.g.; bug deflectors,rollbars or light bars, running boards, ski racks). • Drive with the wheels out of alignment. DRIVING THROUGH WATER WARNING: Drive through water in an emergency only, and not as part of normal driving. WARNING: Engine damage can occu...

FLOOR MATS WARNING: Always use floor mats that are designed to fit the footwell of your vehicle. Only use floor mats that leave the pedal area unobstructed. Only use floor mats that are firmly secured toretention posts so that they cannot slip out of position and interferewith the pedals or impair s...

WARNING (Continued) • Failure to properly follow floor mat installation or attachmentinstructions can potentially cause interference with pedal operationcausing loss of control of vehicle. • To install floor mats, position the floor mat so that the eyelet is overthe retention post and press down to ...

ROADSIDE ASSISTANCE Vehicles Sold in the U.S.: Getting Roadside Assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24 hours a...

U.S. Ford vehicle customers who require Roadside Assistance, call1-800-241-3673. If you need to arrange roadside assistance for yourself, Ford MotorCompany will reimburse a reasonable amount for towing to the nearestdealership within 35 miles (56 kilometers). To obtain reimbursementinformation, U.S....

Connecting the Jumper Cables WARNING: Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery. Note: Do not attach the negative (-) cable to fuel lines, engine rocker covers, the intake...

Jump Starting 1. Start the engine of the booster vehicle and run the engine at amoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizeddealer. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfaction.Pleas...

In Canada: Mailing address Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6K 1C8 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Additional Assistance If you have questions or concerns, or are unsatisfied with the service youare receiving, follow ...

UTILIZING THE MEDIATION or ARBITRATION PROGRAM (CANADAONLY) This pertains to vehicles delivered to authorized Canadian dealers. Inthose cases, where you continue to feel that the efforts by Ford ofCanada and the authorized dealer to resolve a factory-related vehicleservice concern have been unsatisf...

CHANGING A FUSE Fuses WARNING: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. If electrical components in yourvehicle are not working, a fuse mayhave blown. Blown fuses areidentifi...

FUSE SPECIFICATION CHART Power Distribution Box WARNING: Always disconnect the battery before servicing high current fuses. WARNING: To reduce risk of electrical shock, always replace the cover to the power distribution box before reconnecting the battery or refilling fluid reservoirs. The power dis...

Passenger Compartment Fuse Panel The fuse panel is located behind a trim panel on the left side of thedriver’s footwell near the parking brake. To remove the trim panel, slidethe release lever to the right then pull the trim panel out. To remove the fuse panel cover, press in the tabs on both sides ...

Fuse or relay number Fuse amp rating Protected components 23 15A Steering wheel control, Intelligentaccess, Headlamp switch 24 15A On-board diagnostics 25 15A Liftgate release 26 5A Global positioning system module 27 20A Intelligent access 28 15A Ignition switch (withoutintelligent access), Key inh...

Fuse or relay number Fuse amp rating Protected components 41 7.5A Occupant classification sensor,Restraints control module 42 5A Grade assist control switch (2.0Lengine) 43 10A Not used (spare) 44 10A Not used (spare) 45 5A Not used (spare) 46 10A Climate control 47 15A LED signal mirrors 48 30A Cir...

GENERAL INFORMATION Have your vehicle serviced regularly to help maintain its roadworthinessand resale value. There is a large network of Ford authorized dealerswho are there to help you with their professional servicing expertise. Webelieve that their specially trained technicians are best qualifie...

OPENING AND CLOSING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column. 2. Go to the front of the vehicle andrelease the secondary hood latchthat is located under the frontcenter of the hood. 3. Lift the hood and suppor...

ENGINE OIL DIPSTICK A. MIN B. MAX ENGINE OIL CHECK Note: Check the level before starting the engine. Note: Make sure that the level is between the MIN and MAX marks. 1. Make sure that your vehicle is on level ground. 2. Turn the engine off and wait 10 minutes for the oil to drain into theoil pan. 3....

ENGINE COOLANT CHECK Checking the Engine Coolant The concentration and level of engine coolant should be checked at theintervals listed in Scheduled Maintenance Information. Note: Make sure that the level is between the COLD FILL RANGE marks on the coolant reservoir. Note: Coolant expands when it is...

Recycled Engine Coolant Ford Motor Company does NOT recommend the use of recycled enginecoolant since a Ford-approved recycling process is not yet available. Used engine coolant should be disposed of in an appropriate manner. Follow your community’s regulations and standards for recyclingand disposi...

You may notice a reduction in the vehicle’s speed caused by reducedengine power. Your vehicle has been designed to enter this mode ifcertain high temperature/high load conditions take place in order tomanage the engine’s fluid temperatures. The amount of speed reductionwill depend on the vehicle loa...

You have limited engine power when in the fail-safe mode, so drive thevehicle with caution. The vehicle will not be able to maintain high-speedoperation and the engine will run rough. Remember that the engine iscapable of completely shutting down automatically to prevent enginedamage, therefore: 1. ...

Adjusting automatic transmission fluid levels Note: Use of a non-approved automatic transmission fluid may cause internal transmission component damage. Before adding any fluid, make sure the correct type is used. The type offluid used is normally indicated on the dipstick and also in the Capacities...

POWER STEERING FLUID CHECK Check the power steering fluid. Refer to scheduled maintenance information. 1. Start the engine and let it run until it reaches normal operatingtemperature (the engine coolant temperature gauge indicator will benear the center of the normal area between H and C). 2. While ...

CHANGING THE VEHICLE BATTERY WARNING: Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near thebattery, always shield your face and protect your eyes. Always provideproper v...

• Note: If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim iseventually relearned. If the battery has been disconnected or a new battery has been installed,the clock and radio settings must be reset once the battery...

Changing rear window wiper blade The rear wiper arm is designed without a service position. This reducesthe risk of damage to the blade in an automatic car wash. To replace the wiper blade: 1. Grab the wiper arm with one handclose to the arm/blade joint and pullit as far away from the glass aspossib...

4. Locate the vertical adjuster oneach headlamp. Using a Hex headdriver, turn the adjuster eitherclockwise or counterclockwise inorder to adjust the vertical aim ofthe headlamp. 5. Close the hood and turn off the lamps. HORIZONTAL AIM IS NOT REQUIRED FOR THIS VEHICLE AND ISNON-ADJUSTABLE. CHANGING A...

Replacing headlamp bulbs WARNING: Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause thebulb to break the next time the headlamps are operated. Note: If the bulb is accident...

• Spray Motorcraft Engine Shampoo and Degreaser on all parts thatrequire cleaning and pressure rinse clean. In Canada, use MotorcraftEngine Shampoo. • Never wash or rinse the engine while it is hot or running; water in therunning engine may cause internal damage. • Never wash or rinse any ignition c...

CLEANING THE INTERIOR WARNING: Do not use cleaning solvents, bleach or dye on the vehicle’s safety belts, as these actions may weaken the belt webbing. WARNING: On vehicles equipped with seat-mounted airbags, do not use chemical solvents or strong detergents. Such products could contaminate the side...

CLEANING THE ALLOY WHEELS Note: Do not use chrome cleaner, metal cleaner or polish on wheels and wheel covers. A clearcoat paint finish coats aluminum wheels and wheel covers. Inorder to maintain their condition: • Clean weekly with Motorcraft Wheel and Tire Cleaner. Use a sponge toremove heavy depo...

Brakes • Make sure brakes and parking brake are fully released. Tires • Maintain recommended air pressure. Miscellaneous • Make sure all linkages, cables, levers and pins under vehicle arecovered with grease to prevent rust. • Move vehicles at least 25 feet (8 meters) every 15 days to lubricateworki...

GENERAL INFORMATION Important Information for P265/40R22 Low-profile Tires and Wheels Note: Your vehicle’s warranty does not cover these types of damage. Tires should always be kept at the correct inflation pressures and extracaution should be taken when operating on rough roads to avoid impactsthat...

How Your Vehicle Differs from Other Vehicles Crossover vehicles can differ fromsome other vehicles in a fewnoticeable ways. Your vehicle maybe: • Higher – to allow higher loadcarrying capacity. • Shorter – to give it the capabilityto approach inclines. All otherthings held equal, a shorterwheelbase ...

Tire Quality Grades apply to new pneumatic passenger car tires. They donot apply to deep tread, winter-type snow tires, space-saver ortemporary use spare tires, light truck or LT type tires, tires with nominalrim diameters of 10 to 12 inches or limited production tires as defined inTitle 49 Code of ...

• Tread area of the tire: Area of the perimeter of the tire that contacts the road when mounted on the vehicle. • Rim: The metal support (wheel) for a tire or a tire and tube assembly upon which the tire beads are seated. INFORMATION CONTAINED ON THE TIRE SIDEWALL Both U.S. and Canada Federal regula...

D. R: Indicates a radial type tire. E. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheeldiameter. F. 95: Indicates the tire’s load index. It is an index that relates to how much weight a tire can carry. You ma...

Information on T Type Tires T type tires have some additionalinformation beyond those of P typetires. These differences aredescribed below. T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Gradesdo not apply to thi...

INFLATING YOUR TIRES Safe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air pressurewithout appearing flat. Every day before you drive, check your tires. If one looks lower than theothers, use a tire gauge to check pressure o...

WARNING: Age Tires degrade over time depending on many factors such as weather, storage conditions, and conditions of use (such as load, speed,inflation pressure) the tires experience throughout their lives.In general, tires should be replaced after six years regardless of treadwear. However, heat c...

Tire Replacement Requirements WARNING: Only use replacement tires and wheels that are the same size, load index, speed rating and type (such as P-metric versus LT-metric or all-season versus all-terrain) as those originallyprovided by Ford. The recommended tire and wheel size may be found oneither t...

Your vehicle is equipped with tires designed to provide a safe ride andhandling capability. Important: Remember to replace the wheel valve stems when the road tires are replaced on your vehicle. The two front tires or two rear tires should generally be replaced as apair. The tire pressure sensors mo...

If you feel a sudden vibration or ride disturbance while driving, or yoususpect your tire or vehicle has been damaged, immediately reduce yourspeed. Drive with caution until you can safely pull off the road. Stop andinspect the tires for damage. If a tire is under-inflated or damaged,deflate it, rem...

• Front-wheel drive/All-wheel drivevehicles (front tires at left ofdiagram) Sometimes irregular tire wear can be corrected by rotating the tires. USING SNOW CHAINS WARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not r...

• Do not exceed 30 mph (48 km/h) with tire cables on your vehicle. • Remove the tire cables when they are no longer needed. Do not usetire cables on dry roads. TIRE PRESSURE MONITORING SYSTEM WARNING: The tire pressure monitoring system is NOT a substitute for manually checking tire pressure. The ti...

may occur for a variety of reasons, including the installation ofreplacement or alternate tires or wheels on the vehicle that prevent theTPMS from functioning properly. Always check the TPMS malfunctiontelltale after replacing one or more tires or wheels on your vehicle toensure that the replacement...

To restore the full function of the tire pressure monitoring system, havethe damaged road wheel and tire assembly repaired and remounted onyour vehicle. For additional information, see Changing Tires with a Tire Pressure Monitoring System in this section. When You Believe Your System Is Not Operatin...

Low tirepressurewarning light Possible cause Customer action required Flashingwarning light Spare tire in use Repair the damaged road wheel and tire assembly and reinstall it onthe vehicle to restore systemfunction. For a description on howthe system functions, see When Your Temporary Spare Tire isI...

CHANGING A ROAD WHEEL WARNING: The use of tire sealants may damage your tire pressure monitoring system and should not be used. However, if you must use a sealant, have an authorized dealer install a new tirepressure monitoring system sensor and valve stem. WARNING: See Tire Pressure Monitoring Syst...

• Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability • All-wheel driving capability (if applicable) • Load leveling adjustment (if applicable) When driving with the full-size dissimilar spare tire and wheel assembly,additional caution should be...

Stowing the Flat/Spare Tire and Jack Note: If you are stowing a flat 22 inch tire and wheel assembly, temporarily remove the load floor, plastic stowage bins, and the foamload floor supports to make space. Place the 22 inch tire and wheelassembly in the spare tire well with the valve stem facing dow...

Retighten the lug nuts to the specified torque within 100 miles(160 kilometers) after any wheel disturbance (such as rotation, flat tire,wheel removal). Lug nut socket size/Bolt size Wheel lug nut torque* ft-lb N • m 1 ⁄ 2 x 20 100 135 * Torque specifications are for nut and bolt threads free of dir...

ENGINE SPECIFICATIONS Engine 3.5L V6 engine 3.7L V6 engine 2.0L EcoBoost engine Cubic inches 214 227 122 Required fuel Minimum87 octane Minimum87 octane Minimum87 octane Firing order 1–4–2–5–3–6 1–4–2–5–3–6 1–3–4–2 Ignition system Coil on plug Coil on plug Coil on plug Spark plug gap 0.049–0.053 inc...

MOTORCRAFT PART NUMBERS Component 3.5L/3.7L V6engines 2.0L EcoBoost engine Air filter element FA-1884 FA-1884 Battery (non-pushbutton startsystems) BXT-59 BXT-59 Battery (pushbutton startsystems) BXT-65-650 BXT-65-650 Oil filter FL-500-S FL-910S Spark plugs SP-520 1 SP-537 1 Cabin air filter FP65 FP...

The Vehicle Identification Number (VIN) contains the followinginformation: A. World manufacturer identifier B. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintDevices and their location C. Make, vehicle line, series, bodytype D. Engine type E. Check digit F. Model year G. Assembly plant ...

ACCESSORIES For a complete listing of the accessories that are available for yourvehicle, please contact an authorized dealer or visit our online store at www.Accessories.Ford.com (United States only). Ford Motor Company will repair or replace any properly authorizeddealer-installed Ford Genuine Acc...

Peace of mind • Remote start • Keyless entry keypad • Cargo security shade • Vehicle security • Bumper protector • Wheel locks • Locking fuel plug • Cargo area protector • Bumper and hitch mounted parking sensors* • Car cover* *The accessory manufacturer designs, develops and therefore warrantsFord ...

FORD ESP EXTENDED SERVICE PLANS PROTECT YOURSELF FROM THE RISING COST OF VEHICLE REPAIRSWITH A FORD EXTENDED SERVICE PLAN. SERVICE PLANS (U.S. only) More than 32 Million Ford and Lincoln owners have discovered thepowerful protection Ford ESP. It is the only extended service planbacked by Ford Motor ...

Interest Free Financing Options Available Take advantage of our interest free installment payment plan. Just a 10%down payment will provide you with an affordable, no interest, no feepayment program. Complete the information below and mail to: Ford ESPPO Box 8072Royal Oak Michigan 48068-0039 To lear...

GENERAL MAINTENANCE INFORMATION Why Maintain Your Vehicle? Carefully following the maintenance schedule helps protect against majorrepair expenses resulting from neglect or inadequate maintenance andmay help to increase the value of your vehicle when you sell or trade it.Keep all receipts for comple...

Note: Not all dealers have extended hours or body shops. Please contact your dealer for details. Protecting Your Investment Maintenance is an investment that will pay dividends in the form ofimproved reliability, durability and resale value. To maintain the properperformance of your vehicle and its ...

chemicals or additives not approved by Ford Motor Company are notrecommended as part of normal maintenance. Please consult yourwarranty information. Oils, Fluids and Flushing In many cases, fluid discoloration is a normal operating characteristicand, by itself, does not necessarily indicate a concer...

Normal scheduled maintenance * At every oil changeinterval as indicated bythe information display Change engine oil and filter. ** Rotate tires, inspect tire wear and measuretread depth. Perform multi-point inspection(recommended). Inspect automatic transmission fluid level (ifequipped with dipstick...

Other maintenance items 1 Every 20000 miles(32000 km) Replace cabin air filter, or clean screen. Every 30000 miles(48000 km) Replace engine air filter. At 100000 miles(160000 km) Change engine coolant. 2 Every 100000 miles(160000 km) Replace spark plugs. Inspect accessory drive belt(s). 3 Every 1500...

Maintenance Schedule Log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ...

Extensive idling or low-speed driving for long distances as in heavy commercial use (such as delivery, taxi, patrol car or livery) Every 30000 miles(48000 km) Change automatic transmission fluid. Every 60000 miles(96000 km) Replace spark plugs. Operating in dusty or sandy conditions such as unpaved ...

Special Operating Condition Log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D A...

EXCEPTIONS There are several exceptions to the Normal Schedule. They are listedbelow: Normal vehicle axle maintenance: Rear axles and power take-off units with synthetic fluid and light-duty trucks equipped withFord-design axles are lubricated for life; do not check or change fluidunless a leak is s...

Engine air filter & cabin air filter replacement: Engine air filter and cabin air filter life is dependent on exposure to dusty and dirtyconditions. Vehicles operated in these conditions require frequentinspection and replacement of the engine air filter and cabin air filter. ENGINE COOLANT CHAN...

When using SYNC: • Do not operate playing devices if the power cords or cables arebroken, split or damaged. Place cords and cables out of the way, sothey do not interfere with the operation of pedals, seats,compartments or safe driving abilities. • Do not leave playing devices in your vehicle during...

Phone Options during an Active Call During an active call, you have additional menu features which becomeavailable such as putting a call on hold, joining calls, etc. Use the arrowbuttons to scroll through the menu options. To access:1. Press MENU during an active call.2. When Active Call Menu is se...

When you select: You can: Phonebook Access your phonebook contacts.1. Press OK to select, then scroll throughyour phonebook contacts.2. Press OK again when the desired selectionappears in the display.3. Press the phone button. Call History Access your call history log.1. Press OK to select, then scr...

Accessing Features through the Phone Menu SYNC’s phone menu allows you to redial a number, access your callhistory and phone book and send text messages as well as access phoneand system settings. You can also access advanced features, such as 911Assist, Vehicle Health Report and SYNC Services.1. Pr...

When you select: You can: Text Message 1 Enables you to send, download and deletetext messages. Phone Settings 1 Allows you to view your phone’s status, setring tones, select your message notification,change phone book entries and automaticallydownload your cellular phone among otherfeatures. SYNC S...

Receiving a Text Message Note: This is a phone-dependent feature. Your phone must support downloading text messages using Bluetooth to receive incoming textmessages. Note: Forwarding a text message is a speed-dependent feature and can only be done when the vehicle is traveling at 3 mph (5 km/h) or l...

Note: SYNC does not automatically download all of your unread text messages at every ignition cycle (as it does with call history andphonebook if automatic download is set to on). Return exits the current menu when you press OK. If you select Send Text Message? : 1. Press OK to select. If the system...

When you select: You can: Modify Phonebook Modify the contents of your phone book(such as add, delete, download). Press OK toselect and scroll between: Add Contacts: Press OK to add more contactsfrom your phone book. Push the desiredcontact(s) on your phone. See your phone’suser guide on how to push...

System Settings System Settings provide access to your Bluetooth Devices andAdvanced menu features. Use the arrow buttons to scroll through themenu options. The Bluetooth Devices menu allows you to add, connect, delete and set aphone as primary as well as turn your Bluetooth feature on and off. The ...

If you select: You can: Set Bluetooth On/Off Turn the Bluetooth feature on and off.Press OK and scroll to toggle between On andOff. When the desired selection is chosen,press OK. Note: Turning Bluetooth off disconnects all Bluetooth devices and deactivates allBluetooth features. Delete Device Delete...

Advanced Menu Options This menu allows you to access settings such as prompts, languages,defaults, perform a master reset, install an application and view systeminformation.1. Press the phone button to enter the Phone Menu.2. Scroll until System Settings appears and press OK.3. Scroll until Advanced...

If you select: You can: Master Reset Completely erase all information stored onSYNC (phonebook, call history, text messagesand paired devices) and return to the factorydefault settings.Press OK to select. The display indicateswhen complete and SYNC takes you back tothe Advanced menu. Install Applica...

911 Assist Privacy Notice Once 911 Assist is set on, it may disclose to emergency services that thevehicle has been in a crash involving the deployment of an airbag oractivation of the fuel pump shut-off. Certain versions or updates to 911Assist may also be capable of electronically or verbally disc...

The system allows you to check your vehicle’s overall health in the formof a diagnostic report card. The vehicle health report contains valuableinformation such as: • Vehicle Diagnostic Information • Scheduled maintenance • Open Recalls and Field Service Actions • Unserviced items from vehicle inspe...

2. Follow the voice prompts to select your destination. Once your destination is selected, your current vehicle location is uploaded anda route based on current traffic conditions is calculated and sentback to your vehicle. After the route download is complete, thephone call is automatically ended. ...

SYNC Services quick tips Portable Your subscription is associated with yourBluetooth-enabled cellular phone number, notyour VIN (Vehicle Identification Number). Youcan pair and connect your phone to anyvehicle equipped with Traffic, Directions andInformation and continue enjoying yourpersonalized se...

“USB” “Play previous folder” 2 “Play previous track” “Play song <name>” 1,3 “Play track <name>” 1,3 “Refine album <name>” 1,3 “Refine artist <name>” 1,3 “Refine song <name>” 1,3 “Refine track <name>” 1,3 “Repeat off” “Repeat on” “Search album <name>” 1,3 “Se...

Press the voice icon and when prompted say “Bluetooth Audio” and thenany of the following: “BLUETOOTH AUDIO” “(Phone) (Media) (Bluetooth) Connections” “Pause” “Play” “Play next track ” “Play previous track ” Media Menu Features The media menu allows you to select your media source, how to playyour m...

When you select: You can: Select Source SYNC USB: Press OK to access music plugged into your USB port. You can also plugin devices to charge them (if supported byyour device). Once connected, the systemindexes any readable media files. (The timerequired to complete this depends on the sizeof the med...

When you select: You can: Explore USB Explore all supported digital media on yourmedia device connected to the USB port. Youcan only view media content which iscompatible with SYNC; other files saved arenot visible.Press OK to select. Then scroll to exploreindexed media on your flash drive. Similar ...

When you select: You can: Master Reset Completely erase all information stored onSYNC (all phonebook, call history, textmessages and all paired devices) and returnto the factory default settings. Application Download new software applications (ifavailable) and then load the desiredapplications throu...

Vehicle Health Report and SYNC Services (Traffic, Directions and Information) issues Issue Possible cause(s) Possible solution(s) I received a textthat the VehicleHealth Report isnot activated. • Your account may not beactivated on thewebsite, OR • You may have the wrong VIN(vehicleidentificationnum...

INTRODUCTION WARNING: Driving while distracted can result in loss of vehicle control, crash and injury. We strongly recommend that you use extreme caution when using any device that may take your focus offthe road. Your primary responsibility is the safe operation of yourvehicle. We recommend agains...

SETTINGS Press to select any of the following: • Clock • Display • Sound • Vehicle • Settings • Help HOME Press to access your home screen. Depending on your vehicle’soption package and software, your screens may vary in appearance from the descriptions in this section. Your features may alsobe limi...

Support The SYNC support team is available to help you with any questions youcannot answer on your own. Monday-Saturday, 8:30am-9:00pm EST. Sunday, 10:30am-7:30pm EST. In the United States, call: 1–800–392–3673. In Canada, call: 1–800–565–3673. Times are subject to change due to holidays. Safety Inf...

ACCESSING AND ADJUSTING MODES THROUGH YOUR RIGHTVEHICLE INFORMATION DISPLAY (IF EQUIPPED) The display is located on the right side of your instrument cluster. Youcan use your steering wheel controls to view and make minoradjustments to active modes without taking your hands off the wheel.For example...

How to Use Voice Commands with Your System Press the voice icon. After the tone, speak your commandclearly. These commands can be said at any time. “Cancel” “Exit” “Go back” “List of commands” “Main menu” “Next page” “Previous page” “What can I say?” “Help” What Can I Say? To access the available vo...

Browsing Device Content When listening to audio on a device, you can browse through otherdevices without having to change sources. For example, if you arecurrently listening to audio on an SD card, you can browse all the artiststhat are stored on your USB device. Press the voice icon on the steering...

Your voice system allows you to change audio sources with a simplevoice command. For example, if you are listening to music on a USBdevice, then want to switch to a satellite radio channel, simply press thevoice button on the steering wheel controls and say the name of theSirius station (such as, “t...

• Memory presets allow you to save an active channel as a memory preset. Touch and hold a memory preset slot until the sound returns.There is a brief mute while the radio saves the station. Sound returnswhen finished. When switching to an HD2 or HD3 memory preset, thesound mutes before the digital a...

Radio Voice Commands If you are listening to the radio, press the voice button on thesteering wheel control. When prompted, say any of thecommands in the following chart. If you are not listening to the radio, press the voice button and, after thetone, say “Radio”, then any of the commands in the fo...

Sirius Satellite Radio (If Activated) Press the lower left corner of the touchscreen, then select the SIRIUS tab. Presets Save a channel by pressing and holding one of the memory preset areas.There is a brief mute while the radio saves the channel. Sound returnswhen finished. ALERT Save the current ...

Sirius Satellite Radio Information Note: Sirius reserves the unrestricted right to change, rearrange, add or delete programming including canceling, moving or adding particularchannels, and its prices, at any time, with or without notice to you. FordMotor Company shall not be responsible for any suc...

Sirius troubleshooting tips Radio display Condition Possible action Acquiring... Radio requires morethan two seconds toproduce audio for theselected channel. No action required.This message shoulddisappear shortly. Sat Fault/SIRIUSsystem failure. There is an internalmodule or systemfailure present. ...

Sirius troubleshooting tips Radio display Condition Possible action None Found. CheckChannel Guide. All the channels in theselected channels areeither skipped orlocked. Use the channel guideto turn off the Lock or Skip function on that station. Subscription Updated. Sirius has updated thechannels av...

Compression allows you to turn the compression feature on and off. Browse Touch this button to look through all available CD tracks. CD Voice Commands If you are listening to a CD, press the voice button on thesteering wheel control. When prompted, say any of thecommands in the following chart. If y...

• Occupancy Mode • Speed Compensated Volume. Note: Your vehicle may not have all these sound settings. • Media Player Settings allows you to select more settings, which is under Media Player. See Settings. • Device Information displays software and firmware information about the currently connected ...

Supported Media Players, Formats and Metadata Information SYNC is capable of hosting nearly any digital media player, includingiPod®, Zune™, plays from device players, and most USB drives.Supported audio formats include MP3, WMA, WAV and AAC.It is also able to organize your indexed media from your p...

PHONE A. Phone B. Quick Dial C. Phonebook D. History E. Messaging F. Settings Hands-free calling is one of the main features of SYNC. Once you pairyour phone, you can access many options using the touchscreen or voicecommands. While the system supports a variety of features, many aredependent on you...

Phone Menu Options Press the top left corner on your touchscreen to select from thefollowing options: Phone Touch this button to access the on-screen numerical pad to enter anumber and place a call. During an active call, you can also choose to: • Mute the call • Put it on hold • Turn on privacy (re...

Text Messaging Note: Downloading and sending text messages using Bluetooth are phone-dependent features. Note: Certain features in text messaging are speed-dependent and not available when your vehicle is traveling at speeds over 3 mph (5 km/h). Note: SYNC does not download read text messages from y...

You can then preview the message, verify the recipient as well as updatethe message list. Pre-defined text message options I’ll call you back in a few minutes. I just left, I’ll be there soon. Can you give me a call? I’m on my way. I’m running a few minutes late. I’m ahead of schedule, so I’ll be th...

INFORMATION If your vehicle is equipped with Navigation, touch the i(Information) button to access these features. If your vehicle isnot equipped with Navigation, touch the corner of the touchscreen with the green tab. Under the Information menu, you can access features, such as:A. SYNC Services B. ...

Connecting to SYNC Services Using the Touchscreen If your vehicle is equipped with Navigation, touch the i(Information) button to access these features. If your vehicle isnot equipped with Navigation, touch the corner of the touchscreen with the green tab. Press Services. 1. Select Connect to Servic...

SYNC Services Voice Commands When a route has been downloaded (non-navigation systems),press the voice button on the steering wheel control. Whenprompted, say any of the following commands: “SERVICES” “Cancel route” “Navigation voice off” “Navigation voice on” “Next turn” “Route status” “Route summa...

If your vehicle is equipped with Navigation, touch the i(Information) button to access these features. If your vehicle isnot equipped with Navigation, touch the corner of the touchscreen with the green tab. Traffic On Route and Traffic Nearby Touch these buttons to identify traffic incidents on your...

Sirius Travel Link Voice Commands Note: In order to use Sirius Travel Link, your vehicle must be equipped with navigation and your navigation SD card must be in the SD card slot. Press the voice button on the steering wheel controls and, whenprompted, say any of the following: Travel Link voice comm...

Setting 911 Assist On If your vehicle is equipped with Navigation, touch the i(Information) button to access these features. If your vehicle isnot equipped with Navigation, touch the corner of the touchscreen with the green tab. Press Apps > 911 Assist, > On. You can also access 911 Assist by:...

Note: In order to allow a break-in period for your vehicle, you may not be able to create a Vehicle Health Report until your vehicle odometer hasreached 200 miles. Note: Cellular phone and SMS charges may apply when making a report. Register for Vehicle Health Report and set your report preferences ...

SETTINGS A. Clock B. Display C. Sound D. Vehicle E. Settings F. Help Under this menu, you can set your clock, access and adjust the display, sound and vehicle settings as well as access settings for specificmodes or the help feature. Clock Note: You cannot manually set the date. Your vehicle’s GPS d...

From this screen, you can also make other adjustments, such as 12– or24–hour mode, activate GPS time synchronization and have the systemautomatically update for daylight savings time and new time zones. You can also turn the outside air temperature display on and off. Itappears at the top center of ...

To access, press the Settings icon > Display > Edit Wallpaper, and then follow the system prompts to upload your photographs. Only the photograph(s), which meets the following conditions, display: • Compatible file formats are as follows: .jpg, .gif, .png, .bmp. • Each file must be 1.5 MB or l...

Voice Control Press the Settings icon > Settings > Voice Control, then select from the following: Voice control Interaction Mode Standard interaction mode provides moredetailed interaction and guidance. Advancedmode has less audible interaction and moretone prompts. ConfirmationPrompts Have th...

Navigation Press the Settings icon > Settings > Navigation, then select from the following: Navigation Map Preferences Turn breadcrumbs on and off. Have the system display your turn list top tobottom or bottom to top. Turn the Parking POI notification on and off. Route Preferences Have the sys...

Wireless & Internet USB MobileBroadband Instead of using Wi-Fi, your system can alsouse a USB mobile broadband connection toaccess the internet. (You must turn on yourmobile broadband device on your personalcomputer before connecting it to the system.)This screen allows you to set up what is you...

K. Manual controls: Select any of the following airflow distribution modes: • Floor and Defrost: Distributes air through the windshield defroster vents, demister vents, floor vents and rear seat floor vents, andprovides outside air to reduce window fogging. • Panel: Distributes air through the instr...

Your navigation system is comprised of two main features, destinationmode and map mode. To set a destination, press the green corner of your touchscreen, then Dest when it appears. See Setting a destination later in this chapter. To view the navigation map and your vehicle’s current location, touch ...

When programming a point of interest destination, the system allows youto sort the resulting lists alphabetically, by distance or by cityseekrlistings (if available). cityseekr (If Available) Note: cityseekr point of interest information is limited to approximately 154 cities (132 in the United Stat...

Nightlife Attraction This icon appears when your selection exists in multiplecategories within the system. When you are viewing more information for hotels, cityseekr also tellsyou if the hotel has certain services and facilities using icons. Hotel services and facilities Restaurant 24 Hr Room Servi...

For hotels, cityseekr can provide information, such as star rating, pricecategory, review, check-in and check-out times, hotel service icons andwebsite address. Setting Your Navigation Preferences Select settings for the system to take into account when planning yourroute. Press the Settings icon &g...

When you select: You can: Traffic Preferences Choose how you want the system to handletraffic problems along your route. Automatic: Have the system reroute you to avoid traffic incidents that develop andimpact the current route (no notification isprovided). Manual: Have the system always provide a t...

Change the appearance of the mapdisplay by repeatedly pressing thearrow button in the upper leftcorner of the screen. It togglesbetween three different map modes:Heading up, North up, and 3D. Heading up (2D map) always shows the direction of forward travel to be upward on the screen. This view is av...

In 3D mode, rotate the map view by swiping your finger across theshaded bar with the arrows. Map Icons Vehicle mark shows the current location of your vehicle. It stays in the center of the map display, except when in scrollmode. Scroll cursor allows you to scroll the map; the fixed icon is in the c...

“DESTINATION” “Intersection” “Nearest <POI category>” “Nearest POI” “Play nametags” “POI category” “Previous destination” “Street address” “Help” “NAVIGATION” “Destination” * “Zoom city” “Zoom country” “Zoom in minimum” “Zoom out maximum” “Zoom province” “Zoom state” “Zoom street” “Zoom to <...

GENERAL INFORMATION SYNC® End User License Agreement (EULA) • You have acquired a device (“DEVICE”) that includes software licensed by Ford Motor Company and its affiliates (“FORD MOTORCOMPANY”) from an affiliate of Microsoft Corporation (“MS”). Thoseinstalled software products of MS origin, as well...

DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS: • Speech Recognition: If the SOFTWARE includes speech recognition component(s), you should understand that speech recognition is aninherently statistical process and that recognition errors are inherentin the process. Neither FORD MOTOR COMPANY nor its su...

• Security Updates/Digital Rights Management: Content owners use the WMDRM technology included in your DEVICE to protect theirintellectual property, included copyrighted content. Portions of theSOFTWARE on your DEVICE use WMDRM software to accessWMDRM-protected content. If the WMDRM software fails t...

INTELLECTUAL PROPERTY RIGHTS: All title and intellectual property rights in and to the SOFTWARE (including but not limited toany images, photographs, animations, video, audio, music, text and“applets,” incorporated into the SOFTWARE), the accompanying printedmaterials, and any copies of the SOFTWARE...

No Liability for Certain Damages: EXCEPT AS PROHIBITED BY LAW, FORD MOTOR COMPANY, ANY THIRD PARTY SOFTWARE ORSERVICES SUPPLIERS, MS, MICROSOFT CORPORATION AND THEIRAFFILIATES SHALL HAVE NO LIABILITY FOR ANY INDIRECT,SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISINGFROM OR IN CONNECTION WITH THE ...

Keep User’s Guide in Vehicle When kept in the vehicle, the User’s Guide will be a ready reference foryou and other users unfamiliar with the Windows Automotive-basedsystem. Please make certain that before using the system for the firsttime, all persons have access to the User’s Guide and read itsins...

8.4 TeleNav’s or your failure to require performance of any provisionshall not affect that party’s right to require performance at any timethereafter, nor shall a waiver of any breach or default of this Agreementconstitute a waiver of any subsequent breach or default or a waiver ofthe provision itse...

WARNING: This Data may contain inaccurate or incomplete information due to the passage of time, changing circumstances, sources used and the nature of collecting comprehensive geographicData, any of which may lead to incorrect results. No Warranty: This Data is provided to you “as is”, and you agree...

Export Control: You agree not to export from anywhere any part of the Data or any direct product thereof except in compliance with, and withall licenses and approvals required under, applicable export laws, rulesand regulations, including but not limited to the laws, rules andregulations administere...

NOTICE OF USE 425 West Randolph Street, Chicago, IL 60606. This Data is a commercial item as defined in FAR 2.101 and is subject to the EndUser License Agreement under which this Data was provided. 娀 2011 NAVTEQ. All rights reserved. If the Contracting Officer, federal government agency, or any fede...

NOT OBLIGATED TO PROVIDE YOU WITH ANY ENHANCED ORADDITIONAL DATA TYPES THAT GRACENOTE MAY CHOOSE TOPROVIDE IN THE FUTURE AND IS FREE TO DISCONTINUE ITSONLINE SERVICES AT ANY TIME. GRACENOTE DISCLAIM ALLWARRANTIES EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITEDTO, IMPLIED WARRANTIES OF MERCHANTABILITY...

911 Assist™ ......................397, 475 A ABS (see Brakes) .....................206 Accessing and using your USBport ............................................452 Accessing call history/phonebook during active call .............386 Accessing your calendar ..........474 Accessing your media menu...

Blind Spot InformationSystem .......................................226 Booster seats ...............................22 Brakes ........................................206 anti-lock ...................................206anti-lock brake system (ABS)warning light ...........................206brake war...

fluid, checking and adding(automatic) .....................293, 295fluid, refill capacities ..............347lubricant specifications ..........347 Turn signal ..................................94 U USB port ....................141–142, 452 Using privacy mode ..................386 V Vehicle health r...