Ford 2013 Edge v.1- User Manual

ABOUT THIS MANUAL Thank you for choosing Ford. We recommend that you take some time toget to know your vehicle by reading this manual. The more that youknow about it, the greater the safety and pleasure you will get fromdriving it. WARNING: Always drive with due care and attention when using and ope...

SYMBOL GLOSSARY WARNING: You risk death or serious injury to yourself and others if you do not follow the instruction highlighted by the warning symbol. These are some of the symbols you may see on your vehicle. Symbol Description Symbol Description Symbol Description Safety Alert See Owner’sManual ...

DATA RECORDING Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, st...

CALIFORNIA PROPOSITION 65 WARNING: Some constituents of engine exhaust, certain vehicle components, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to theState of California to cause cancer and birth defects or otherreproductive harm. PERCH...

WARNING: Front seat mounted rear-facing child or infant seats should NEVER be placed in front of an active passenger airbag. MOBILE COMMUNICATIONS EQUIPMENT Using mobile communications equipment is becoming increasinglyimportant in the conduct of business and personal affairs. However, youmust not c...

GENERAL INFORMATION See the following sections for directions on how to properly use safetyrestraints for children. WARNING: Always make sure your child is secured properly in a device that is appropriate for their height, age and weight. Child safety restraints must be purchased separately from the...

Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommendedrestraint type Infantsortoddlers Children weighing 40 lb (18 kg) or less(generally age four or younger). Use a child safetyseat (sometimescalled an infantcarrier, convertibleseat, or toddler seat). Small...

WARNING: Always restrain an unoccupied child seat or booster seat. These objects may become projectiles in a collision or sudden stop, which may increase the risk of serious injury. WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it r...

BOOSTER SEATS WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the riskof injury or death in a collision. Use a belt-positioning booster seat for children who ha...

Types of Booster Seats • Backless booster seats If your backless booster seat has a removable shield, remove the shield.If a vehicle seating position has a low seat back or no head restraint, abackless booster seat may place your child’s head (as measured at thetops of the ears) above the top of the...

Perform the following steps when installing the child seat withcombination lap/shoulder belts: Note: Although the child seat illustrated is a forward facing child seat, the steps are the same for installing a rear facing child seat. 1. Position the child safety seat in aseat with a combination lap a...

4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear a snap and feel the latchengage. Make sure the tongue islatched securely by pulling on it. 5. To put the retractor in theautomatic locking mode, grasp...

Use of Inboard Lower Anchors from the Outboard SeatingPositions (Center Seating Use) WARNING: The standardized spacing for LATCH lower anchors is 11 in. (28 cm) center to center. Do not use LATCH lower anchors for the center seating position unless the child seatmanufacturer’s instructions permit an...

4. Tighten the child safety seat tether strap according to themanufacturer’s instructions. If your child restraint system is equipped with a tether strap, and thechild restraint manufacturer recommends its use, Ford also recommendsits use. CHILD SAFETY LOCKS When these locks are set, the rear doors ...

PRINCIPLES OF OPERATION WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips. WARNING: To reduce the risk of injury, make sure children sit where they can be properly restrained. WARNING: Never let a passenger hold a child on his or her lap while th...

FASTENING THE SAFETY BELTS The front outboard and rear safety restraints in the vehicle arecombination lap and shoulder belts. 1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until you hear a snap and feelit latch. Make sure the tongue is...

To adjust the comfort guide: 1. Slip the shoulder belt into the belt guide. 2. Slide the guide up or down along thewebbing so that the belt is centered on theoccupant’s shoulder. Restraint of Pregnant Women WARNING: Always ride and drive with your seatback upright and the safety belt properly fasten...

Safety Belt Locking Modes WARNING: After any vehicle collision, the safety belt system at all passenger seating positions must be checked by an authorized dealer to verify that the automatic locking retractor feature for childseats is still functioning properly. In addition, all safety belts should ...

How to use the automatic locking mode 1. Buckle the combination lap and shoulderbelt. 2. Grasp the shoulder portion and pulldownward until the entire belt is pulled out. Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the autom...

SAFETY BELT HEIGHT ADJUSTMENT Front seats WARNING: Position the safety belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat beltand increase the risk of injury in a collision. Adjust the...

Deactivating/Activating the Belt-Minder 姞 Feature WARNING: While the system allows you to deactivate it, this system is designed to improve your chances of being safely belted and surviving an accident. We recommend you leave the system activatedfor yourself and others who may use the vehicle. To re...

One-time Belt-Minder 姞 disable If at any time the driver/front passenger quickly buckles then unbucklesthe safety belt for that seating position, the system is disabled for thecurrent ignition cycle. The feature will enable during the same ignitioncycle if the occupant buckles and remains buckled fo...

PERSONAL SAFETY SYSTEM™ The Personal Safety System provides an improved overall level of frontalcrash protection to front seat occupants and is designed to help furtherreduce the risk of airbag-related injuries. The system is able to analyzedifferent occupant conditions and crash severity before act...

WARNING: All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag supplemental restraint system is provided. The airbags are a supplemental restraint system and are designed towork with the safety belts to help protect the driver and ri...

DRIVER AND PASSENGER AIRBAGS WARNING: Never place your arm or any objects over an airbag module. Placing your arm over a deploying airbag can result in serious arm fractures or other injuries. Objects placed on or over theairbag inflation area may cause those objects to be propelled by theairbag int...

Proper Driver and Front Passenger Seating Adjustment WARNING: National Highway Traffic Safety Administration (NHTSA) recommends a minimum distance of at least 10 in. (25 cm) between an occupant’s chest and the driver airbag module. To properly position yourself away from the airbag: • Move your seat...

FRONT PASSENGER SENSING SYSTEM WARNING: Even with Advanced Restraints Systems, children 12 and under should be properly restrained in a rear seating position. WARNING: Sitting improperly out of position or with the seat back reclined too far can take off weight from the seat cushion and affect the d...

Note: When the passenger airbag status indicator OFF lamp is illuminated, the passenger side airbag (seat mounted) may be disabled toavoid the risk of airbag deployment injuries. After all occupants have adjusted their seats and put on safety belts, it’svery important that they continue to sit prope...

• Driver and/or adult passengers should check for any objects lodgedunderneath the front passenger seat or cargo interfering with the seat. • Remove the obstruction(s) (if found). • Restart the vehicle. • Wait at least two minutes and verify that the airbag readiness light inthe instrument cluster i...

CRASH SENSORS AND AIRBAG INDICATOR WARNING: Modifying or adding equipment to the front end of the vehicle (including frame, bumper, front end body structure and tow hooks) may affect the performance of the airbag system,increasing the risk of injury. Do not modify the front end of the vehicle. The v...

The fact that the safety belt pretensioners or airbags did not activate forboth front seat occupants in a collision does not mean that something iswrong with the system. Rather, it means the restraints control moduledetermined the accident conditions (crash severity, belt usage, etc.) werenot approp...

PRINCIPLE OF OPERATION The remote control allows you to: • remotely lock or unlock the vehicle doors • unlock the doors without actively using a key or remote control(intelligent access only) • remotely open the power liftgate (if equipped) • remotely start or stop the engine (if equipped) • arm and...

Intelligent Access (If Equipped) The system uses a radio frequency signal to communicate with yourvehicle and authorize your vehicle to unlock when commanded (either bytouching the inside of the driver door or front passenger exterior doorhandle, by activating the exterior power liftgate button, or ...

The intelligent access key alsocontains a removable mechanical keyblade that can be used to unlock thedriver door. Slide the release on theback of the transmitter to release thekey blade, then pull the blade out. Note: Your vehicle’s back-up keys were issued with a security tag thatprovides importan...

Memory Feature (If Equipped) This feature allows you to recall the driver seat and power mirrorsmemory positions. Press the unlock button on the remote control or activate intelligentaccess (if equipped) to recall memory. The seat and power mirrorsautomatically move to the memory position. The mirro...

Sounding a Panic Alarm Note: The panic alarm will only operate when the ignition is off. Press the button to activate the alarm. Press the button againor turn the ignition on to deactivate. Remote Start (If Equipped) WARNING: To avoid exhaust fumes, do not use remote start if your vehicle is parked ...

The ignition must be turned on and then back off or allow one hour topass before using remote start again if additional remote starts aredesired. Turning the Engine Off After Remote Starting Press the button once. The parking lamps will turn off. You may have to be closer to the vehicle than when st...

PRINCIPLES OF OPERATION MyKey 威 allows you to program keys with restricted driving modes to promote good driving habits. All but one of the keys programmed to thevehicle can be activated with these restricted modes. Any keys that havenot been programmed are referred to as an “administrator key” or“a...

• Audio system maximum volume of 45%. A message in the audiosystem is displayed when attempting to exceed the limited volume.Also, Speed sensitive compensated volume (sscv) feature will bedisabled. • Always on setting. When this is selected you will not be able to disable911 Assist, AdvanceTrac 威 or...

In addition to the key that they have already programmed as a MyKey 威 , owners of vehicles equipped with traditional keys may want to programthe non-Ford-approved remote start system as a MyKey 威 if the remote start fob is used by the MyKey 威 driver. To program a non-Ford-approved remote start syste...

LOCKING AND UNLOCKING You can use the power door lock control or the remote control to lockand unlock the vehicle. Power Door Locks A. Unlock B. Lock Remote Control The remote control can be used any time the vehicle is not running. Unlocking the Doors (Two-Stage Unlock) Press the button to unlock t...

Power Liftgate (If Equipped) WARNING: Make sure all persons are clear of the liftgate area before using power liftgate control. WARNING: Make sure the liftgate is closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out. If you m...

Smart Unlocks for Integrated Keyhead Transmitter This feature helps to prevent you from locking yourself out of the vehicleif your key is still in the ignition. When you open one of the front doors and lock the vehicle with thepower door lock control, all the doors will lock then unlock if your key ...

Autolock Feature (If Enabled) The autolock feature will lock all the doors when: • all the doors are closed, • the ignition is on, • you shift into any gear putting the vehicle in motion, and • the vehicle attains a speed greater than 12 mph (20 km/h). The autolock feature repeats when: • any door i...

Power Liftgate (If Equipped) WARNING: Make sure all persons are clear of the power liftgate area before using the power liftgate control. WARNING: Keep keys out of the reach of children. Do not allow children to operate the power liftgate, or to play near to an open or moving power liftgate. Note: C...

To open or close from the instrument panel: Press the instrument panel button. To open or close with the remote control: Press the remote control button twice within three seconds. To open with the outside liftgatecontrol button: 1. Unlock the liftgate with the remotecontrol or power door unlock con...

Resetting the Power Liftgate The liftgate may not operate properly and may need to be reset if any ofthese conditions occur: • a low voltage or dead battery • disconnected battery • the liftgate is manually closed and left ajar (unlatched) To reset the power liftgate: 1. Disconnect the battery for 2...

4. For memory recall feature, enter the sixth digit 1 • 2 to store driver 1 settings or 3 • 4 to store driver 2 settings. Note: Pressing 5 • 6, 7 • 8, or 9 • 0 keypad numbers as a sixth digit will not recall a driver memory setting. Note: The factory-set code cannot be associated with a memory setti...

Unlocking and Locking the Doors To unlock the driver’s door: enter the factory set 5-digit code or your personal code. Each number must be pressed within five seconds of eachother. The interior lamps will illuminate. Note: All doors will unlock if the two-stage unlocking feature is disabled. Refer t...

ADJUSTING THE STEERING WHEEL WARNING: Do not adjust the steering wheel when your vehicle is moving. Note: Make sure that you are sitting in the correct position. Refer to Sitting In the Correct Position in the Seats chapter. 1. Unlock the steering column. 2. Adjust the steering wheel to thedesired p...

VOICE CONTROL (IF EQUIPPED) A. Phone mode B. Voice recognition Refer to the SYNC 威 or MyFord Touch™ chapter. CRUISE CONTROL Type 1 Type 2 Refer to the Cruise Control chapter for information on this feature. SEEK VOL A B SET RES CNCL ON OFF GAP Steering Wheel 85 2013 Edge (edg) Owners Guide gf, 1st P...

INFORMATION DISPLAY CONTROL Refer to the Information Displays chapter for more information. Cluster Display Control Features If equipped with: MyFord™ system: This control functions the same as the centercontrol on the faceplate. Refer to MyFord system in the Audio Systems chapter. MyFord Touch™: Us...

WINDSHIELD WIPERS Note: Fully defrost the windshield in icy conditions before turning on the windshield wipers. Rotate the end of the control awayfrom you to increase the speed ofthe wipers. Rotate toward you todecrease the speed of the wipers. Press the stalk down and release fora single swipe of t...

WINDSHIELD WASHERS Note: Do not operate the wipers on a dry windshield. This may scratch the glass, damage the wiper blades or cause the wiper motor to burn out.Always use the windshield washer before wiping a dry windshield. Note: Do not operate the washer when the washer reservoir is empty. This m...

LIGHTING CONTROL A. Off B. Parking lamps, instrument panellamps, license plate lamps and taillamps C. Headlamps High Beams Push the lever forward to switch thehigh beams on. Push the lever forward again or pullthe lever toward you to switch thehigh beams off. Headlamp Flasher Pull toward you slightl...

AUTOLAMPS WARNING: In severe weather conditions, it may be necessary to switch your headlamps on manually. Note: If the vehicle is equipped with autolamps, it will have the windshield wiper rainlamp feature. When the windshield wipers are turned to low- or high-speed wiping during daylight, and the ...

HEADLAMP EXIT DELAY You can set the delay time to keep the headlamps on for up to threeminutes after the ignition is turned off. Follow the steps below to change the delay time (Steps 1 through 6 mustbe done within 10 seconds): 1. Turn the vehicle off. 2. Turn the lighting control to the autolamp po...

DIRECTION INDICATORS The turn signal lever does not mechanically lock in the upward ordownward position when activated. The turn signal control activation andcancellation is electronic. • Push down to activate the left turnsignal. • Push up to activate the right turnsignal. • Push the lever again in...

Map/dome lamp (if equipped) The dome lamp lights when: • any door is opened. • the dome lamp button on theinstrument panel is activated. • any of the remote entry controlsare pressed and the ignition is off. The map lamps are activated by pressing the controls on either side ofthe lens. Rear courtes...

POWER WINDOWS WARNING: Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure themselves. WARNING: When closing the power windows, you should verify they are free of obstructions and make sure that children and pets are not in t...

Window Lock A. Unlock B. Lock Press the control to lock or unlock the rear window controls. EXTERIOR MIRRORS Power Exterior Mirrors WARNING: Do not adjust the mirror while the vehicle is in motion. A. Left-hand mirror B. Off C. Right-hand mirror To adjust your mirrors: 1. Select the mirror you want ...

Heated Exterior Mirror (If Equipped) Note: Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions couldcause damage to the glass and mirrors. Note: Do not clean the housing or glass of any mirror with harsh abrasives, fuel or...

The approaching vehicle’s image issmall and near the inboard edge ofthe main mirror when it is at adistance. The image becomes largerand begins to move outboard acrossthe main mirror as the vehicleapproaches (A). Its image willtransition from the main mirror andbegin to appear in the blind spotmirro...

INTERIOR MIRROR WARNING: Do not adjust the mirror when your vehicle is moving. Note: Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum or ammonia based cleaning products. You can adjust the interior mirror to your preference. Some mirrors alsohave a second...

Illuminated Visor Vanity Mirror (If Equipped) Lift the cover to switch on the lamp. PANORAMIC VISTA ROOF™ AND POWER SUNSHADES(IF EQUIPPED) WARNING: Do not let children play with the panoramic Vista Roof™ and power sunshade or leave children unattended in the vehicle. They may seriously hurt themselv...

Opening the Sunshade and Moonroof Note: The moonroof will only open after sunshades are completely open. Press and release the control toopen the sunshade. The front andrear sunshades open simultaneously. Press and release the control to open the moonroof. The moonroof willstop short of the fully op...

GAUGES Type 1 Cluster shown in standard measure – metric clusters similar. A. Tachometer B. Information display. See Information displays for more information. C. Speedometer D. Fuel gauge Fuel Gauge Indicates approximately how much fuel is left in the fuel tank (when theignition is on). The fuel ga...

Type 2 Cluster shown in standard measure – metric clusters similar. A. Information display. See Information displays for more information. B. Speedometer C. Infotainment display. See MyFord Touch™ for more information. WARNING LAMPS AND INDICATORS These lights can alert you to a vehicle condition th...

• Engaged (green light): Illuminates when the adaptive cruise controlsystem is engaged. Turns off when the speed control system is disengaged. Airbag readiness If this light fails to illuminate when the ignition is turned on,continues to flash or remains on, contact your authorized dealeras soon as ...

Charging system (RTT) Illuminates when the battery is not charging properly. If it stayson while the engine is running, there may be a malfunction withthe charging system. Contact your authorized dealer as soon as possible. This indicates a problem with the electrical system or a relatedcomponent. D...

Low tire pressure warning Illuminates when your tire pressure is low. If the light remainson at start up or while driving, the tire pressure should bechecked. When the ignition is first turned to on, the light will illuminate for 3 seconds to ensure the bulb is working. If the light doesnot turn on ...

Menu You can access the menus using the information display control. Note: Some options may appear slightly different or not at all if the items are optional. †Trip 1 / 2 Trip Odometer Trip Timer Distance to E Inst Fuel Econ Average Fuel Fuel Used Compass (located in lower line of display). Note: th...

Settings Driver Assist Traction Control Blind Spot CollisionWarning Sensitivity High, Normal orLow Chimes (not selectable if using aMyKey) Warning (not selectable if using aMyKey) Cross Traffic Rear Park Aid Trailer Sway Display Language English, Español or Français Units Distance Miles andGallons o...

Settings MyKey Create MyKey Hold OK to Create MyKey 911 Assist Always On / User Selectable Traction Control Always On or User Selectable Max Speed 80 MPH (130 km/h) or Off Speed Warning 45 mph (75 km/h), 55 mph(90 km/h), 65 mph (105 km/h) orOff Volume Limiter Clear MyKeys Hold OK to Clear MyKeys Sys...

Fuel Used Shows the amount of fuel used for a given trip. Total Odometer Registers the total mileage of the vehicle. Compass (non MyFord/MyLincoln Touch units only) Displays the vehicle’s heading direction. To calibrate the compass: Enter the compass menu and select Calibrate.Follow the prompts. To ...

Information Display Controls(Type 2) • Press the up and down arrowbuttons to scroll through andhighlight the options within amenu. • Press the right arrow button toenter a sub-menu. • Press the left arrow button to exita menu. • Press the OK button to chooseand confirm a setting/messages. The small ...

Fuel Economy Use the left/right arrow buttons to choose the desired fueleconomy display. Fuel Economy Inst. Fuel Economy XX. Min Fuel History Instantaneous fuel usage x †Fuel usage over a 5, 10, or30 minute time span x Total odometer (lower left corner) Press and hold OK to reset the currently displ...

Vehicle Autolamp Delay Off or number of seconds Easy Entry/Exit On / Off Fuel DTE Calculation Normal, Towing Locks Autolock, On / Off Autounlock On / Off RemoteUnlocking All doors / Driver’s door Menu Control Standard / Memory On (See Menu control later in this section) Oil Life Reset Set to XXX % P...

Menu control To change the menu control between Standard or Memory On, refer to Vehicle > Menu Control found in the table under Settings in this chapter. • Standard: when in the Display, Trip or Fuel Economy sub-categories,scrolling up and down will always exit back to the main categories. • Memo...

Battery and Charging System Messages Action / Description Check ChargingSystem Displayed when the charging system needsservicing. If the warning stays on or continuesto come on, contact your authorized dealer assoon as possible. Turn Power Off toSave Battery Displayed when the battery managementsyst...

Collision Warning System Messages Action / Description Collision WarningMalfunction Displayed when there is a system malfunctionwith the collision warning system. The systemwill be disabled. Contact your authorizeddealer as soon as possible. Collision WarningDisplay Fault Displayed when there is a s...

Maintenance Messages Action / Description LOW Engine OilPressure Stop the vehicle as soon as safely possible,turn off the engine. Check the oil level. If thewarning stays on or continues to come on withyour engine running, contact your authorizeddealer as soon as possible. Change Engine OilSoon Disp...

Passenger Sensing System Message Action / Description Remove Objects NearPassenger Seat Displayed when objects are by the passengerseat. After the objects are moved away fromthe seat, if the warning stays on or continuesto come on contact your authorized dealer assoon as possible. Reminder Messages ...

GENERAL AUDIO INFORMATION Radio Frequencies and Reception Factors AM and FM frequencies are established by the Federal CommunicationsCommission (FCC) and the Canadian Radio and TelecommunicationsCommission (CRTC). Those frequencies are: AM: 530, 540–1700, 1710 kHz FM: 87.9–107.7, 107.9 MHz Radio rec...

Always handle discs by their edges only. Clean the disc with an approvedCD cleaner only, wiping from the center of the disc toward the edge. Donot clean in a circular motion. Do not expose discs to direct sunlight or heat sources for extendedperiods of time. MP3 Track and Folder Structure Audio syst...

MyFord™ SYSTEM WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that you use extreme caution when using any device or feature that may takeyour focus off the road. Your primary responsibility is the safe operationof the vehicle. W...

When you select: You can: G. OK Allows you to confirm commands with specialphone and media features. If your vehicle isequipped with SYNC, refer to the SYNC chapter for more information. H. Eject Eject the CD. I. Power and Volume Press the power control to turn the system onand off.Turn to adjust th...

AM/FM SINGLE CD PREMIUM AUDIO SYSTEM WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that you use extreme caution when using any device or feature that may takeyour focus off the road. Your primary responsibility is the safe oper...

AM/FM/SINGLE CD SONY 姞 AUDIO SYSTEM WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that you use extreme caution when using any device or feature that may takeyour focus off the road. Your primary responsibility is the safe opera...

When you select: You can: A. SOURCE Access different audio modes such as AM, FMand A/V Input. B. Seek/Reverse/FastForward In radio mode, select a frequency band and press one of the seek buttons. The systemstops at the first station it finds in thatdirection. In SIRIUS mode, select the previous or n...

USB PORT WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that you use extreme caution when using any device or feature that may takeyour focus off the road. Your primary responsibility is the safe operationof the vehicle. We reco...

SATELLITE RADIO INFORMATION (IF EQUIPPED) Satellite Radio Channels SIRIUS 威 broadcasts a variety of music, news, sports, weather, traffic and entertainment satellite radio channels. For more information and acomplete list of SIRIUS 威 satellite radio channels, visit www.siriusxm.com in the United Sta...

MANUAL HEATING AND AIR CONDITIONING SYSTEM A. Fan speed control: Controls the volume of air circulated in your vehicle. Turn to select the desired fan speed or switch off. If you switchthe fan off, the windshield may fog up. B. Defrost: Distributes air through the windshield defroster vents and de-m...

F. Temperature control: Controls the temperature of the air circulated in your vehicle. Turn to select the desired temperature. G. MAX A/C: Distributes recirculated air through the instrument panel vents to cool the vehicle. This position is more economical and efficientthan normal A/C. H. Air distr...

DUAL AUTOMATIC TEMPERATURE CONTROL SYSTEM Note: You can switch temperature units between Fahrenheit and Celsius. Refer to Menu features in the MyFord Touch or MyLincoln Touch chapter. A. Power/Driver temperature control: Press to turn the climate control system on and off. When the system is off, ou...

E. MAX A/C: Distributes recirculated air through the instrument panel vents to cool the vehicle. This position is more economical and efficientthan normal A/C. F. A/C: Press the button to turn air conditioning on or off. Air conditioning cools the vehicle using outside air. To improve air conditioni...

During extreme high ambient temperatures when idling stationary forextended periods of time in gear, it is recommended to run the A/C inthe MAX A/C mode, adjust the blower fan speed to the lowest settingand put the vehicle’s transmission into the P (Park) position (vehiclesequipped with an automatic...

During extreme high ambient temperatures when idling stationary forextended periods of time in gear, it is recommended to run the A/C inthe MAX A/C mode, adjust the blower fan speed to the lowest settingand put the vehicle’s transmission into the P (Park) position (vehiclesequipped with an automatic...

CABIN AIR FILTER Note: A cabin air filter must be installed at all times to prevent foreign objects from entering the system. Running the system without a filter inplace could result in degradation or damage to the system. Your vehicle is equipped with a cabin air filter, which is located just infro...

Manual Climate Systems In hot weather, the climate control system is set to MAX A/C. In moderate weather, the system either heats or cools (based on previoussettings). The rear defroster and/or heated mirrors are not automaticallyturned on. In cold weather, maximum heat is provided in floor/defrost ...

SITTING IN THE CORRECT POSITION WARNING: Sitting improperly out of position or with the seatback reclined too far can take off weight from the seat cushion and affect the decision of the passenger sensing system,resulting in serious injury or death in a crash. Always sit upright againstyour seatback...

• Lower: Press and hold the guide sleeve adjust/release button (D) and push down on the head restraint (A). • Remove: Pull up the head restraint until it reaches the highest adjustment position and then press and hold both the adjust/releasebutton (D) and the unlock/remove button (C), then pull up o...

Moving the seats backwards andforwards Adjusting the height of thedriver’s seat WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Recline adjustment WARNING: Cover sharp edges on the load to help prevent injury to occupants. Secure the load to h...

WARNING: Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull onthe seatback to ensure that it has fully latched. An unlatched seat maybecome dangerous in the event...

MEMORY FUNCTION (IF EQUIPPED) The memory control, located on theinstrument panel, allows automaticpositioning of the driver seat andpower mirrors to two programmablepositions. Programming a memory position Note: A memory position may be programmed at any time. • To program position 1, move the memor...

REAR SEATS WARNING: To prevent possible damage to the seat or safety belts, ensure that the safety belts are not buckled when folding the seatback. • Recline Seatback: With the seat occupied, pull the lever up to recline the seatback. • Fold Seatback: With the seat empty, pull the lever up to fold t...

REAR SEAT ARMREST Press the latch and pull the armrestforward for armrest/cupholder use. To access the cup holders, lift up one ofthe slotted areas on the cover. To close the armrest, close the cupholder cover and rotate the armrestrearward until the latch clicks. Seats 165 2013 Edge (edg) Owners Gu...

HOMELINK 姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED) WARNING: Make sure that the garage door and security device are free from obstruction when you are programming. Do not program the system with the vehicle in the garage. WARNING: Do not use the system with any garage door opener that does not have the...

Erasing the Function Button Codes Note: You can not erase individual buttons. 1. Press and hold the outer twofunction buttons simultaneously forapproximately 20 seconds until theindicator lights above the buttonsflash rapidly. 2. When the indicator lights flash,release the buttons. The codes forall ...

4. Press and release the Genie Intellicode 威 2 transmitter’s previously programmed button. Both LED’s on the garage door opener motor unitshould now flash purple. 5. Press and hold the previously programmed HomeLink 威 button for two seconds. Repeat this step up to three times until the garage door m...

AUXILIARY POWER POINTS Note: Do not insert objects other than an accessory plug into the power point. This will damage the outlet and blow the fuse. Note: Do not hang any type of accessory or accessory bracket from the plug. Note: Improper use of the power outlet can cause damage not covered by your...

CENTER CONSOLE WARNING: Use only soft cups in the cupholder. Hard objects can injure you in a collision. Your vehicle may be equipped with a variety of console features. A. Cupholders B. Two pen/pencil holders, traveltissue pack holder, and businesscard/paper holder. C. Rear powerpoint D. Utility co...

The fast restart feature allows you to restart your vehicle within20 seconds of switching the vehicle off, if a valid passive key is notpresent. Apply the brake pedal and press the start button for up to20 seconds. After 20 seconds have expired, you can no longer start yourvehicle without the passiv...

We recommend that you do the following for safe and correct operation: • Use a 16-gauge outdoor extension cord that is product certified byUnderwriter’s Laboratory or Canadian Standards Association. Thisextension cord must be able to be used outdoors, in coldtemperatures, and be clearly marked Suita...

SAFETY PRECAUTIONS WARNING: Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. WARNING: The fuel system may be under pressure. If you hear a hissing sound near the fuel filler door (Easy Fuel 威 “no cap” fuel system), do not refuel unt...

• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes,remove contact lenses (if worn), flush with water for 15 minutes andseek medical attention. Failure to seek proper medical attention couldlead to permanent injury. • Fuels can also be harmful if absorbed through the skin. If f...

Do not be concerned if your enginesometimes knocks lightly. However,if it knocks heavily while you areusing fuel with the recommendedoctane rating, see your authorizeddealer to prevent any enginedamage. RUNNING OUT OF FUEL Avoid running out of fuel because this situation may have an adverseeffect on...

When filling the vehicle’s fuel tank from a portable fuel container, use thefunnel included with the vehicle. 1. Locate the white plastic funnel in the spare tirecompartment. 2. Slowly insert the funnel into the capless fuelsystem. 3. Fill the vehicle with fuel from the portable fuelcontainer. 4. Wh...

Easy Fuel 姞 “No Cap” Fuel System WARNING: The fuel system may be under pressure. If you hear a hissing sound near the fuel filler door, do not refuel until the sound stops. Otherwise, fuel may spray out, which could cause seriouspersonal injury. When fueling your vehicle: 1. Turn the engine off. 2. ...

EMISSION CONTROL SYSTEM WARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. WARNING: Exhaust leaks may result in entry of harmful and potentially lethal fumes into th...

AUTOMATIC TRANSMISSION WARNING: Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the off position and remove the key whenever you leave your vehicle. Your vehicle has been designed to improve fuel economy by reducing fuelusage while coasting...

• Provides additional lower gear operation through the automatictransmission shift strategy which reacts to vehicle inputs (vehicleacceleration, accelerator pedal, brake pedal and vehicle speed). • Gears are selected more quickly and at higher engine speeds. Note: The system will stay in S (Sport) u...

Apply the parking brake and turn the ignition off before performing thisprocedure. 1. Using a screwdriver (or similar tool),carefully pry off and remove the BSIaccess panel. 2. Locate the brake shift interlock lever in front of theshifter assembly. 3. Apply the brake pedal. Gently push and hold the ...

DRIVING IN SPECIAL CONDITIONS WITH AWD AWD vehicles are equipped for driving on sand, snow, mud and roughroads and have operating characteristics that are somewhat differentfrom conventional vehicles, both on and off the highway. When driving at slow speeds in deep sand under high outsidetemperature...

WARNING: Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a passenger or bystander. Note: Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur. Note: Do not rock the vehicle for more than a few minutes or d...

GENERAL INFORMATION Note: Occasional brake noise is normal. If a metal-to-metal, continuous grinding or continuous squeal sound is present, the brake linings may beworn-out and should be inspected by an authorized dealer. If the vehiclehas continuous vibration or shudder in the steering wheel while ...

PRINCIPLES OF OPERATION The traction control system helps avoid drive wheel spin and loss oftraction. If your vehicle begins to slide, the system applies the brakes to individualwheels and, when needed, reduces engine power at the same time. If thewheels spin when accelerating on slippery or loose s...

PRINCIPLES OF OPERATION WARNING: Vehicle modifications involving braking system, aftermarket roof racks, suspension, steering system, tire construction and/or wheel/tire size may change the handlingcharacteristics of the vehicle and may adversely affect the performanceof the AdvanceTrac 威 system. In...

SENSING SYSTEM (IF EQUIPPED) WARNING: To help avoid personal injury, please read and understand the limitations of the system as contained in this section. Sensing is only an aid for some (generally large and fixed)objects when moving in reverse on a flat surface at parking speeds.Traffic control sy...

The system can be turned off using the information display control. Referto the Information Display chapter. If a fault is present in the system, a warning message appears in the information display and does not allowthe driver to switch the faulted system on. Note: If your vehicle is equipped with ...

Using the Rear View Camera System The rear view camera system displays what is behind your vehicle whenyou place the transmission in R (Reverse). The system uses two types ofguides to help you see what is behind your vehicle:1. Fixed guidelines: Show the actual path the vehicle is moving in while re...

Manual Zoom WARNING: When manual zoom is on, the full area behind the vehicle is not shown. Be aware of your surroundings when using the manual zoom feature. Note: Manual zoom is only available when the transmission is in R (Reverse). Note: When manual zoom is enabled, only the centerline is shown. ...

PRINCIPLES OF OPERATION Cruise control lets you maintain a set speed without keeping your foot onthe accelerator pedal. USING CRUISE CONTROL WARNING: Do not use cruise control in heavy traffic or on roads that are winding, slippery or unpaved. Note: Vehicle speed may vary momentarily when driving up...

At startup, the system sets the gap to the last selected setting. Onceactivated, the driver can deactivate the system at any time by pressingthe brake pedal, pressing the steering wheel ON/OFF control or pressingthe RES/CNCL control. In addition, the driver can temporarily increasethe vehicle speed ...

Following a Vehicle WARNING: When following a vehicle in front of you, the vehicle will not decelerate automatically to a stop, nor will the vehicle always decelerate quickly enough to avoid a collision without driverintervention. Always apply the brakes when necessary. Failing to do somay result in...

Detection Issues The radar sensor has a limited field of vision. It may not detect vehicles atall or detect a vehicle later than expected in some situations. The leadvehicle graphic will not illuminate if a vehicle is not detected in front of you. Detection issues can occur: A. When driving on a dif...

Blocked Sensor WARNING: Do not use ACC when towing a trailer with brake controls. Aftermarket trailer brakes will not function properly when ACC is activated because the brakes are electronically controlled.Failing to do so may result in loss of vehicle control, which could resultin serious injury. ...

Cause Action Swirling water, or snow or ice onthe surface of the road mayinterfere with the radar signals Do not use ACC in these conditionbecause it may not detect, warn,or respond to potential collisions. Desert / remote area with no othervehicles and no roadside objects Wait a short time or switc...

BLIND SPOT INFORMATION SYSTEM (BLIS 姞 ) WITH CROSS TRAFFIC ALERT (CTA) (IF EQUIPPED) WARNING: To help avoid injuries, NEVER use the BLIS 威 as a replacement for using the interior and exterior mirrors and looking over your shoulder before changing lanes. BLIS 威 is not a replacement for careful drivin...

Using the Systems BLIS 威 turns on when the engine is started and the vehicle is driven forward above 3 mph (5 km/h); it remains on while the transmission is inD (Drive) and N (Neutral). If shifted out of D (Drive) or N (Neutral), thesystem enters CTA mode. Once shifted back into D (Drive), BLIS 威 tu...

Zone coverage also decreases when parking at shallow angles. Here, theleft sensor is mostly obstructed; zone coverage on that side is severelylimited. System Lights and Messages The BLIS 威 and CTA systems illuminate a yellow alert indicator inthe outside mirror on the side of thevehicle the approach...

System Errors If either system senses a problem with the left or right sensor, the BLIS 威 indicator illuminates and remains on and BLIND SPOT SYSTEM FAULT or CROSS TRAFFIC SYSTEM FAULT appears in the information display. When problems that may cause the left or rightindicator not to illuminate, only...

If it is, a red warning lightilluminates and an audible warningchime sounds. The brake support system assists the driver in reducing the collisionspeed by charging the brakes. If the risk of collision further increasesafter the warning light illuminates, the brake support prepares the brakesystem fo...

System Limitations WARNING: The collision warning system’s brake support can only help reduce the speed at which a collision occurs if the driver applies the vehicle’s brakes. The brake pedal must be pressedjust like any typical braking situation. Due to the nature of radar technology, there may be ...

STEERING To help prevent damage to the power steering system: • Never hold the steering wheel at its furthest turning points (until itstops) for more than three to five seconds while the engine is running. • Do not operate the vehicle with a low power steering pump fluidreservoir level (below the MI...

CARGO NETS WARNING: This net is not designed to restrain objects during a collision or heavy braking. The cargo net secures lightweight objects in the cargo area. Attach the net to the anchors provided in one of the two configurations.Repeat the attachment on both sides of the vehicle. Type 1 Load C...

ROOF RACKS AND LOAD CARRIERS (IF EQUIPPED) WARNING: When loading the roof rail crossbars, it is recommended to evenly distribute the load, as well as maintain a low center of gravity. Loaded vehicles, with higher centers of gravity,may handle differently than unloaded vehicles. Extra precautions, su...

UTILITY HOOK The utility hook can be used tohang small items such as grocerybags, etc. Do not hang more than10 pounds (4.5 kilograms) on thehook. LOAD LIMIT Vehicle Loading – With and Without a Trailer This section will guide you in the proper loading of your vehicle and/ortrailer, to keep your load...

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-Pillar or the edge of the driver’s door(vehicles exported outside the US and Canada may not have a TireLabel). Look for “THE COMBINED WEI...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loadweight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb wei...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label.The label shall be affixed to either the door hinge pillar,door-latch post, or the door edge that meets the doo...

• Example only: WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structuraldamage, serious damage to the vehicle, loss of control and personalinjury. 238 Load Carrying 20...

GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo andpassengers – that the vehicle can handle without r...

Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that willbe riding in your vehicle. 3. Subtract the combin...

TOWING A TRAILER WARNING: Do not exceed the GVWR or the GAWR specified on the certification label. WARNING: Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage, transmission damage, structural damage, lossof vehicle c...

RECOMMENDED TOWING WEIGHTS Powertrain Maximum GCWR - lb (kg) Maximum Trailer Weight - lb (kg) FWD 2.0L 6170 (2799) 1500 (680) FWD 3.5L 1 8210 (3724) 2000 (907) FWD 3.5L 2 8210 (3724) 3500 (1588) AWD 3.5L 1 8400 (3810) 2000 (907) AWD 3.5L 2 8400 (3810) 3500 (1588) FWD 3.7L 6780 (3075) 2000 (907) AWD ...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift anddollies or flatbed equipment. Do not tow w...

TOWING THE VEHICLE ON FOUR WHEELS Emergency Towing In the event your vehicle becomes disabled (without access to wheeldollies, car-hauling trailer, or flatbed transport vehicle), it can beflat-towed (all wheels on the ground, regardless of thepowertrain/transmission configuration) under the followin...

BREAKING-IN Your vehicle does not need an extensive break-in. Try not to drivecontinuously at the same speed for the first 1,000 miles (1,600 km) ofnew vehicle operation. Vary your speed frequently in order to give themoving parts a chance to break in. Drive your new vehicle at least 1,000 miles (1,...

• Drive a heavily loaded vehicle or tow a trailer. • Carry unnecessary weight (approximately 1 mpg [0.4 km/L] is lost forevery 400 lb [180 kg] of weight carried). • Add particular accessories to your vehicle (e.g. bug deflectors,rollbars/light bars, running boards, ski racks). • Drive with the wheel...

FLOOR MATS WARNING: Always use floor mats that are designed to fit the foot well of your vehicle. Only use floor mats that leave the pedal area unobstructed. Only use floor mats that are firmly secured toretention posts so that they cannot slip out of position and interferewith the pedals or impair ...

WARNING (Continued) • Failure to properly follow floor mat installation or attachmentinstructions can potentially cause interference with pedal operationcausing loss of control of vehicle. • To install floor mats, position the floor mat so that the eyelet is overthe retention post and press down to ...

ROADSIDE ASSISTANCE Vehicles sold in the U.S. : Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24-hours,...

Vehicles sold in the U.S. : Using roadside assistance Complete the roadside assistance identification card and place it in yourwallet for quick reference. This card is found in the owner’s informationportfolio in the glove compartment. U.S. Ford vehicle customers who require Roadside Assistance, cal...

FUEL CUT-OFF SWITCH WARNING: Failure to inspect and if necessary repair fuel leaks after a collision may increase the risk of fire and serious injury. Ford Motor Company recommends that the fuel system be inspected byan authorized dealer after any collision. In the event of a moderate to severe coll...

Preparing Your Vehicle When the battery is disconnected or a new battery is installed, theautomatic transmission must relearn its shift strategy. As a result, thetransmission may have firm soft shifts, firm shifts or both. This operationis considered normal and will not affect function or durability...

1. Connect the positive (+) jumpercable to the positive (+) terminal ofthe discharged battery. 2. Connect the other end of thepositive (+) cable to the positive(+) terminal of the assisting battery. 3. Connect the negative (-) cable tothe negative (-) terminal of theassisting battery. 4. Make the fi...

Removing the Jumper Cables Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery. Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable fromthe ground metal surface. 2. Remove the jumper cable on thenega...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizeddealer. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfaction. Plea...

In Canada: Mailing address Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Additional assistance If you have questions or concerns, or are unsatisfied with the service youare receiving, follow ...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of ...

CHANGING A FUSE Fuses If electrical components in the vehicleare not working, a fuse may haveblown. Blown fuses are identified by abroken wire within the fuse. Checkthe appropriate fuses before replacingany electrical components. Note: Always replace a fuse with one that has the specified amperage r...

FUSE SPECIFICATION CHART Power Distribution Box WARNING: Always disconnect the battery before servicing high current fuses. WARNING: To reduce risk of electrical shock, always replace the cover to the power distribution box before reconnecting the battery or refilling fluid reservoirs. The power dis...

Fuse/Relay Number Fuse Amp Rating Protected Components 86 7.5A* PCM relay, PCM keep-alive(3.5/3.7L engines) 87 5A* Run/start relay 88 — Run/start relay 89 — Not used 5A* Headlamp leveling motors (Chinaonly) 90 10A* PCM, Transmission ControlModule (TCM) (2.0L engine) 91 10A* Adaptive cruise control (...

To reinstall the trim panel, align the tabs on the bottom of the panel withthe grooves, push the panel shut and slide the release lever to the left tosecure the panel. To remove a fuse, use the fuse puller tool provided on the fuse panelcover. The fuses are coded as follows. Fuse/Relay Number Fuse A...

Fuse/Relay Number Fuse Amp Rating Protected Components 28 15A Ignition switch (without IA), Keyinhibit solenoid, Push button start(with IA) 29 20A Radio, Multi-function displayscreen, Electronic finish panel,SYNC 威 module 30 15A Front park lamps, Auxiliary parklamps 31 5A Not used (spare) 32 15A Loc...

Fuse/Relay Number Fuse Amp Rating Protected Components 46 10A Climate control 47 15A LED signal mirrors 48 30A Circuit Breaker Power windows 49 — Delayed accessory relay 276 Fuses 2013 Edge (edg) Owners Guide gf, 1st PrintingUSA (fus)

GENERAL INFORMATION Have your vehicle serviced regularly to help maintain its roadworthinessand resale value. There is a large network of Ford authorized dealers thatare there to help you with their professional servicing expertise. Webelieve that their specially trained technicians are best qualifi...

OPENING AND CLOSING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column. 2. Go to the front of the vehicle andrelease the secondary hood latchthat is located under the frontcenter of the hood. 3. Lift the hood and suppor...

ENGINE OIL DIPSTICK A. – MIN B. – MAX ENGINE OIL CHECK Note: Check the level before starting the engine. Note: Make sure that the level is between the MIN and MAX marks. 1. Make sure that your vehicle is on level ground. 2. Turn the engine off and wait 10 minutes for the oil to drain into the oilpan...

ENGINE COOLANT CHECK Checking the coolant level The concentration and level of engine coolant should be checked at theintervals listed in scheduled maintenance information. Note: Make sure that the level is between the MIN and MAX marks on the coolant reservoir. Note: For best results, coolant conce...

Note: Do not use stop leak pellets or cooling system sealants/additives as they can cause damage to the engine cooling and/or heating systems.This damage would not be covered under your vehicle’s warranty. Note: During normal vehicle operation, the engine coolant may change color from orange to pink...

The air conditioning may also cycle on and off during severe operatingconditions to protect overheating of the engine. When the engine coolanttemperature decreases to a more normal operating temperature, the airconditioning will turn on once again. If you notice any of the following: • the engine co...

The service engine soon indicator will illuminate. If the engine reaches a preset over-temperature condition, the engine willautomatically switch to alternating cylinder operation. Each disabledcylinder acts as an air pump and cools the engine. When this occurs the vehicle will still operate. Howeve...

4. Check the coolant level and replenish if low. 5. Re-start the engine and take your vehicle to an authorized dealer. Note: Driving the vehicle without repairing the engine problem increases the chance of engine damage. Take your vehicle to an authorized dealeras soon as possible. TRANSMISSION FLUI...

Low fluid level If the fluid level is below the MINrange of the dipstick, add fluid toreach the hash mark level. Note: If the fluid level is below the MIN level, do not drive the vehicle. An underfill condition may cause shift and/orengagement concerns and/or possible damage. Correct fluid level The...

If an overfill occurs, excess fluidshould be removed by an authorizeddealer. Note: An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. Do not use supplemental transmission fluid additives, treatments orcleaning agents. The use of these mater...

5. If the fluid is low, add fluid in small amounts, continuously checkingthe level until it reaches the range between the MIN and MAX lines. Besure to put the cap back on the reservoir. Refer to the Capacities and Specifications chapter for the proper fluid type. FUEL FILTER Your vehicle is equipped...

If the battery has been disconnected or a new battery has been installed,the clock and the preset radio stations must be reset once the battery isreconnected. Note: Always dispose of automotive batteries in a responsible manner. Follow your local authorized standards for disposal. Call your local au...

CHANGING THE WIPER BLADES 1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Press the locktab to release the blade and pull thewiper blade down toward thewindshield to remove it from the arm. 2. Attach the new wiper to the wiperarm and press it into place unti...

4. Attach the new wiper to the wiperarm and press it into place until a clickis heard. If you find this procedure too difficult,please see your dealer. AIR FILTER CHECK WARNING: To reduce the risk of vehicle damage and/or personal burn injuries do not start your engine with the air cleaner removed a...

For vehicles with halogen headlamps: On the wall or screen you willobserve a flat zone of high intensitylight located at the top of the righthand portion of the beam pattern. Ifthe top edge of the high intensitylight zone is not at the horizontalreference line, the headlamp willneed to be adjusted. ...

Examples of acceptable condensation are: • Presence of thin mist (no streaks, drip marks or droplets) • Fine mist covers less than 50% of the lens Examples of unacceptable moisture (usually caused by a lamp waterleak) are: • Water puddle inside the lamp • Large water droplets, drip marks or streaks ...

WAXING • Wash the vehicle first. • Use a quality wax that does not contain abrasives. • Do not allow paint sealant to come in contact with any non-body(low-gloss black) colored trim, such as grained door handles, roofracks, bumpers, side moldings, mirror housings or the windshield cowlarea. The pain...

CLEANING THE ALLOY WHEELS Note: Do not use chrome cleaner, metal cleaner or polish on wheels and wheel covers. Aluminum wheels and wheel covers are coated with a clear coat paintfinish. In order to maintain their shine: • Clean weekly with Motorcraft 威 Wheel and Tire Cleaner. Heavy dirt and brake du...

Brakes • Make sure brakes and parking brake are fully released. Tires • Maintain recommended air pressure. Miscellaneous • Make sure all linkages, cables, levers and pins under vehicle arecovered with grease to prevent rust. • Move vehicles at least 25 feet (8 m) every 15 days to lubricateworking pa...

GENERAL INFORMATION Important Information for P265/40R22 Low-profile Tires and Wheels Note: Your vehicle’s warranty does not cover these types of damage. Tires should always be kept at the correct inflation pressures and extracaution should be taken when operating on rough roads to avoid impactsthat...

How Your Vehicle Differs from Other Vehicles Crossover vehicles can differ fromsome other vehicles in a fewnoticeable ways. Your vehicle may be: • Higher – to allow higher loadcarrying capacity. • Shorter – to give it the capabilityto approach inclines. All otherthings held equal, a shorterwheelbase...

U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford Motor Company to give youthe following information about tire grades exactly as the governmenthas written it. Treadwear The treadwear grade is a comparative rating based on the wear rate ofthe ...

Information Contained on the Tire Sidewall Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identifi...

Note: You may not find this information on all tires because it is not required by federal law. G. H: Indicates the tire’s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods oftime under a standard condition of load and inflation pressure. ...

Additional Information Contained on the Tire Sidewall for “LT ”Type Tires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below. Note: Tire Quality Grades do not apply to this type of tire. A. LT: Indicates a tire, designated by the Tire ...

Information on “T” Type Tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Grades donot apply ...

Inflating Your Tires Safe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air pressurewithout appearing flat. Every day before you drive, check your tires. If one looks lower than theothers, use a tire gauge to check pressure o...

WARNING: Age Tires degrade over time depending on many factors such as weather, storage conditions, and conditions of use (load, speed, inflationpressure, etc.) the tires experience throughout their lives.In general, tires should be replaced after six years regardless of treadwear. However, heat cau...

It is recommended that the two front tires or two rear tires generally bereplaced as a pair. The tire pressure sensors mounted in the wheels (originally installed onyour vehicle) are not designed to be used in aftermarket wheels. The use of wheels or tires not recommended by Ford Motor Companymay af...

Tire and Wheel Alignment A bad jolt from hitting a curb or pothole can cause the front end of yourvehicle to become misaligned or cause damage to your tires. If yourvehicle seems to pull to one side when you’re driving, the wheels may beout of alignment. Have an authorized dealer check the wheel ali...

USING SNOW CHAINS WARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety and performanceof your vehicle, which could result in an increased risk of loss of vehiclecontrol, vehicl...

TIRE PRESSURE MONITORING SYSTEM Each tire, including the spare (if provided), should be checkedmonthly when cold and inflated to the inflation pressurerecommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. As an added safety feature, your vehicle has been eq...

WARNING: The tire pressure monitoring system is NOT a substitute for manually checking tire pressure. The tire pressure should be checked periodically (at least monthly) using a tire gauge,see Inflating your tires in this chapter. Failure to properly maintain your tire pressure could increase the ri...

To restore the full functionality of the tire pressure monitoring system,have the damaged road wheel/tire repaired and remounted on yourvehicle. For additional information, refer to Changing tires with a TPMS in this section. When you believe your system is not operating properly The main function o...

Low tirepressurewarning light Possible cause Customer action required Flashingwarning light Spare tire in use Repair the damaged road wheel/tire and reinstall it on the vehicle torestore system functionality. For adescription on how the systemfunctions, refer to When your temporary spare tire is ins...

• Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability • All-wheel driving capability (if applicable) • Load leveling adjustment (if applicable) When driving with the full-size dissimilar spare tire and wheel assembly,additional caution should be...

Vehicle jacking 1. Block the diagonally oppositewheel. 2. Loosen each wheel lug nutone-half turn counterclockwise butdo not remove them until the wheelis raised off the ground. 3. The vehicle jacking points are shown here, and are depicted on theyellow warning label on the jack. Jack at the specifie...

TECHNICAL SPECIFICATIONS Wheel Lug Nut Torque Specifications Retighten the lug nuts to the specified torque within 100 miles (160 km)after any wheel disturbance (rotation, flat tire, wheel removal, etc.). Lug nut socket size/Bolt size Wheel lug nut torque* ft-lb N • m 1 ⁄ 2 x 20 100 135 * Torque spe...

The Vehicle Identification Number (VIN) contains the followinginformation: A. World manufacturer identifier B. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintDevices and their location C. Make, vehicle line, series, bodytype D. Engine type E. Check digit F. Model year G. Assembly plant ...

ACCESSORIES For a complete listing of the accessories that are available for yourvehicle, please contact your dealer or visit our online store at: Accessories.Ford.com (U.S. only). Ford Custom Accessories are available for your vehicle through yourlocal Ford or Ford of Canada dealer. Ford Motor Comp...

FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY) More than 32 million Ford and Lincoln owners have discovered thepowerful protection of Ford ESP. It is the only extended service planbacked by Ford Motor Company, and provides “peace of mind” protectionbeyond the New Vehicle Limited Warranty coverage. Up t...

FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY) You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is the only service contractbacked by Ford Motor Company of Canada, Limited. Depending on theplan you purchase, Ford ESP provides benefits such as: • R...

GENERAL MAINTENANCE INFORMATION Why Maintain Your Vehicle? Carefully following the maintenance schedule helps protect against majorrepair expenses resulting from neglect or inadequate maintenance andmay also help to increase the value of your vehicle when you sell ortrade it. Keep all receipts for c...

Convenience Many dealerships have extended evening and Saturday hours to makeyour service visit more convenient and they offer one stop shopping.They can perform any services that are required on your vehicle, fromgeneral maintenance to collision repairs. Note: Not all dealers have extended hours or...

Additives and Chemicals Ford Motor Company recommended additives and chemicals are listed inthis book and in the Workshop Manual. Additional chemicals or additives not approved by Ford and are not recommended as part ofnormal maintenance. Please consult your Warranty Manual for complete warranty inf...

Normal Scheduled Maintenance - At every oil change interval as indicated by the message center Change engine oil and filter Rotate tires, inspect tire wear and measure tread depth Perform multi-point inspection (recommended) Inspect automatic transmission fluid level (if equipped with dipstick);cons...

Maintenance Schedule Log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ...

SPECIAL OPERATING CONDITIONS If you operate your vehicle primarily in any of the following conditions, you need to perform additional maintenance as indicated. If you occasionally operate your vehicle under any of these conditions, it is not necessary to perform the additional maintenance. For speci...

Extensive idling and/or low-speed driving for long distances as in heavy commercial use (i.e. delivery, taxi, patrol car or livery) As required Change engine oil and filter as indicated bymessage center and perform services listed in theNormal Scheduled Maintenance chart Inspect frequently,service a...

Police Interceptor equipped with engine idle hour meter Inspect frequently,service as required Replace cabin air filter (if equipped) Every 5,000 miles(8,000 km) Inspect the brake system Lubricate control arm and steering ball joints ifequipped with grease fittings Rotate tires, inspect tires for we...

ENGINE IDLE HOUR METER (IF EQUIPPED): Your vehicle may be equipped with an idle meter to indicate how muchtime the vehicle is idling in P (Park) or N (Neutral). The meter isincorporated with the vehicle odometer. Depressing the odometer-resetbutton once will display the trip odometer (miles [km] fol...

Special Operating Condition Log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D A...

EXCEPTIONS There are several exceptions to the Normal Schedule. They are listedbelow: Normal vehicle axle maintenance: Rear axles and power take-off (PTO) units with synthetic fluid and light-duty trucks equipped withFord-design axles are lubricated for life; do not check or change fluidunless a lea...

Edge/MKX AWD only – vehicles operating off-road in sand during high ambient temperatures must replace the AWD PTU (All-wheel drivePower Transfer Unit) lube every 20,000 miles (32,000 km). Engine air filter & cabin air filter replacement: Engine air filter and cabin air filter life is dependent o...

GENERAL INFORMATION Ensure that you review your device’s user guide before using it withSYNC 威 . Support The SYNC support team is available to help you with any questions youcannot answer on your own. Monday-Saturday, 8:30 am-8pm EST In the United States, call: 1–888–270–1055 In Canada, call: 1–800–...

Privacy Information When a cellular phone is connected to SYNC 威 , the system creates a profile within your vehicle that is linked to that cellular phone. Thisprofile is created in order to offer you more cellular features and tooperate more efficiently. Among other things, this profile may containd...

Phone Options during an Active Call During an active call, you have additional menu features which becomeavailable such as putting a call on hold, joining calls, etc. Use the arrowbuttons to scroll through the menu options. To access:1. Press MENU during an active call.2. When Active Call Menu is se...

When you select: You can: Call History Access your call history log.1. Press OK to select, then scroll through yourcall history options (incoming, outgoing ormissed).2. Press OK when the desired selection appearsin the display.3. Press the phone button to call the selection. Return Exit the current ...

Text Messaging Note: This is a phone-dependent feature. SYNC allows you to receive, send, download and delete text messages.The system can also read incoming text messages to you so that you donot have to take your eyes off the road. Receiving a Text Message Note: This is a phone-dependent feature. ...

2. Scroll to cycle through the following options: Pre-defined text message options Be there in 10 minutes Be there in 20 minutes Call me Call you later Can’t talk right now Can’t wait to see you I love you I need more directions I’m stuck in traffic No Thanks Too funny Where R you? Why? Yes 9. Press...

Note: SYNC does not automatically download all of your unread text messages at every ignition cycle (as it does with call history andphonebook if automatic download is set to on). Return exits the current menu when you press OK. Accessing Your Phone Settings These are phone-dependent features. Your ...

When you select: You can: Modify Phonebook Modify the contents of your phone book (i.e. add,delete, download). Press OK to select and scrollbetween: Add Contacts: Press OK to add more contactsfrom your phone book. “Push” the desiredcontact(s) on your phone. Refer to your phone’suser guide on how to ...

System Settings System Settings provide access to your Bluetooth Devices andAdvanced menu features. Use the arrow buttons to scroll through themenu options. The Bluetooth Devices menu allows you to add, connect, delete and set aphone as “primary” as well as turn your Bluetooth feature on and off. Th...

If you select: You can: Connect BluetoothDevice Connect a previously paired Bluetooth-enabledphone.1. Press OK to select and view a list of previouslypaired phones.2. Scroll until the desired device is chosen, thenpress OK to connect the phone. Note: Only one device can be connected at a time. When ...

Vehicle Health Report WARNING: Always follow scheduled maintenance instructions, regularly inspect your vehicle, and seek repair for any damage or problem you suspect. Vehicle Health Report supplements, but cannotreplace normal maintenance and vehicle inspection. Vehicle HealthReport only monitors c...

To run a report (after the vehicle has been running a minimum of60 seconds):1. Press the phone button to enter Phone Menu.2. Scroll until Vehicle Health is selected and press OK.3. Scroll to select from the following options: Vehicle Health Report options User Preferences:Press OK to selectand enter...

SYNC 姞 Services: Traffic, Directions & Information (TDI) Note: SYNC 威 Services requires activation prior to use. Visit www.SYNCMyRide.com to register and check your eligibility forcomplimentary services. Standard phone and message rates may apply.Subscription may be required. You must also have ...

3. While on an active route, you can select or say “Route Summary” or “Route Status” to view the Route Summary turn list or the RouteStatus ETA. You can also turn voice guidance on or off, cancel theroute or update the route. If you miss a turn, SYNC automatically asks if you want the routeupdated. ...

“USB” “Search song <name>” 1 “Search track <name>” 1,3 “Shuffle off” “Shuffle on” “Similar music” “What’s playing?” 1 “<name>” is a dynamic listing, meaning that it could be the name of any desired group, artist, etc. 2 Voice commands which are only available in folder mode. For mo...

Voice Command Guide “Refine” This allows you to make your previouscommand more specific. For example, if youasked to search and play all music by acertain artist, you could then say “refinealbum” and choose a specific album from thelist to view. If you then select Play, the systemonly plays music fr...

When you select: You can: Select Source Select and play music from your USB port,auxiliary input jack (line in) or stream musicfrom your Bluetooth-enabled phone.Press OK to select, then scroll to choose from: USB: Press OK to access music plugged intoyour USB port. You can also plug in devices tocha...

Accessing Your Play Menu This menu allows you to select and play your media by artist, album,genre, playlist, track, similar music or even to explore what is on yourUSB device.1. Make sure that your device is plugged into the USB port and is turned on. 2. Press AUX and then MENU to enter the Media M...

When you select: You can: Explore USB Explore all supported digital media on yourmedia device connected to the USB port. Youcan only view media content which iscompatible with SYNC; other files saved arenot visible.Press OK to select. Then scroll to exploreindexed media on your flash drive. Similar ...

Advanced Menu Options This menu allows you to access settings such as prompts, language,performing a master reset as well as returning to factory defaults.1. Press AUX and then MENU to access the Media Menu.2. Scroll until System Settings appears and select OK.3. Scroll until Advanced appears.4. Pre...

When you select: You can: Master Reset Completely erase all information stored onSYNC (all phonebook, call history, textmessages and all paired devices) and returnto the factory default settings. Application Download new software applications (ifavailable) and then load the desiredapplications throu...

Phone issues Issue Possible Cause(s) Possible Solution(s) I’m having troubleconnecting myphone to SYNC. This is a phonedependentfeature, ORPossible phonemalfunction. Go to the website to review yourphone’s compatibility.Try turning off the device,resetting the device or removingthe device’s battery,...

INTRODUCTION WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that maytake their focus off the road. Your primary responsibility is the safeoperation of the vehicle...

Press to access your home screen. Depending on your vehicle’s option package and software, yourscreens may vary in appearance from the screens shown in this section. Your features may also be limited depending on your market.Check with your authorized dealer for availability. Customizing Your Home S...

• SOUND: Touch the word to access the Sound menu where you can makeadjustments to settings such as: Bass, Treble, Midrange, Balance andFade, THX Deep Note Demo (if equipped), DSP (if equipped),Occupancy Mode (if equipped), and Speed Compensated Volume settings. • Hazard flasher: Press the button to ...

Navigation Climate You can make selections from the menu by using the OK button ortouching the screen. If you make a selection by touching the screen, theselection menu expands and you are allowed different options. • Press the up and down arrows to scroll through the modes. • Press the right arrow ...

What Can I Say? To access the available voice commands for the current session, do oneof the following: • During a voice session, press the lower left status bar of the screen,OR • Say “What can I say?” for an on-screen listing of the possible voicecommands associated with your current voice session...

Helpful Hints • Make sure the interior of the vehicle is as quiet as possible. Wind noisefrom open windows and road vibrations may prevent the system fromcorrectly recognizing spoken commands. • After pressing the voice icon, wait until after the tone sounds and“Listening” appears before saying a co...

LISTENING TO MUSIC Your system offers many media options. You can access these optionsusing the touchscreen or voice commands. Browse Voice Commands When listening to any type of audio, you can browse through otherdevices without having to change sources. For example, if you arecurrently listening t...

When you select: You can: Options Adjust more audio system settings: Sound Settings allows you to adjust Bass, Treble, Midrange, Balance and Fade, THXDeep Note Demo (if equipped), DSP (ifequipped), Occupancy Mode (if equipped),and Speed Compensated Volume settings. Set PTY for Seek/Scan allows you t...

Radio Voice Commands If you are listening to the radio, press the voice button on thesteering wheel controls. When prompted, say any of thecommands in the following chart. If you are not listening to the radio, press the voice button and, after thetone, say “Radio”, then any of the commands in the f...

“TUNE” “<530–1710>” “AM” “AM <530–1710>” “AM Preset <#>” “AM Autoset” “AM Autoset Preset <#>” “<87.9–107.9>” “FM” “FM1” “FM2” “FM <87.9–107.9>” “FM Preset <#>” “FM 1 Preset <#>” “FM 2 Preset <#>” “FM Autoset” “FM Autoset Preset <#>” “<87...

When this feature is enabled and you are tuned to a station broadcastingHD Radio technology, you may notice the following indicators on yourscreen: HD) logo blinks when a digital station is being acquired and is solidwhen digital audio is playing. Whenthis logo is available, you may alsosee Title an...

HD Radio Reception/Station Troubleshooting Potential reception issues Reception area If you are listening to a multicast station andyou are on the fringe of the reception area,the station may mute due to weak signalstrength.If you are listening to HD1, the systemswitches back to the analog broadcast...

SIRIUS 姞 Satellite Radio Voice Commands If you are listening to SIRIUS 威 satellite radio, press the voice button on the steering wheel controls. When prompted, say anyof the commands in the following chart. If you are not listening to SIRIUS 威 satellite radio, press the voice button and, after the t...

CD Press the lower left corner of the touchscreen, then select theCD tab. You can choose from Repeat, Shuffle, Scan and Options.Options allows you to select additional sound settings: When you select: You can: Sound Settings Adjust Bass, Treble, Midrange, Balance andFade, THX Deep Note Demo (if equi...

CD voice commands “Shuffle Folder”* “Shuffle Off” “Help” *(WMA or MP3 only) SD Card Note: Your SD card slot is spring-loaded. To remove the SD card, press the card in and the system ejects it. Do not attempt to pull the card toremove it as this could cause damage. The card slot can be used for your ...

To view song information such as Title, Artist, File, Folder, Album, andGenre, touch the on-screen album art. You can also press What’s Playing to hear how the system pronounces the current band and song. This can be helpful when using voicecommands to make sure the system correctly plays your reque...

To view song information such as Title, Artist, File, Folder, Album, andGenre, touch the on-screen album art. You can also press What’s Playing to hear how the system pronounces the current band and song. This can be helpful when using voicecommands to make sure the system correctly plays your reque...

Bluetooth Audio Voice Commands If you are listening to a Bluetooth Audio device, press the voicebutton on the steering wheel controls. When prompted, say anyof the commands in the following chart. If you are not listening to a Bluetooth Audio device, press the voicebutton and, after the tone, say “B...

Phone Menu Options Press the top left corner on your touchscreen to select from thefollowing options: When you select: You can: Phone Access the on-screen numerical pad to enter anumber and place a call.During an active call, you can also choose tomute the call, put it on hold, activate privacy(retu...

When you select: You can: Messaging send text messages using your touchscreen.Refer to Text messaging later in this section. Settings Access various phone settings such asBluetooth on or off, Manage your Phone Bookand more. Refer to Phone settings later in this section. Text Messaging Note: Download...

Phone Settings Press Phone > Settings, or Menu > Settings > Phone, then select fromthe following settings: If you select: You can: Bluetooth Devices Connect, disconnect, add or delete a device, aswell as save it as a favorite. Bluetooth on/off Turn Bluetooth on or off. Do not disturb Have a...

Disconnecting from SYNC 姞 Services 1. Press and hold the phone button on the steering wheel.2. Say “Goodbye” from the SYNC Services main menu. TDI options Personalizing You can personalize your services feature toprovide quicker access to your most used orfavorite information. You can save address p...

When you select: You can: Sports Info. View scores and schedules from a variety ofsports. You can also save up to 10 favorite teamsfor easier access. The score automaticallyrefreshes when a game is in progress. Movie Listings View nearby movie theaters and their show times(if available). Ski Conditi...

Calendar Press the information button, then select Calendar. You canview the current calendar by day, week or month. 911 Assist™ (If Equipped) WARNING: Unless the 911 Assist™ setting is set on prior to a crash, the system will not dial for help which could delay response time, potentially increasing...

MENU FEATURES Under the menu setting, you can set your clock, access and makeadjustments to the display, sound and vehicle settings as well as accesssettings for specific modes or the help feature. Setting the Clock Note: The date is set by your vehicle’s GPS; you cannot manually set the date. Note:...

Photo Display Limitations Only the photograph(s) which meet the following conditions aredisplayed: • Compatible file formats are as follows: .jpg, .gif, .png, .bmp • Each file must be 1.5 MB or less. • Recommended dimensions: 800 x 378 Photographs with extremely large dimensions (i.e., 2048 x 1536) ...

Valet Mode Note: If you are locked out and need to reset the PIN, you can enter 3681 and the system unlocks. Valet mode allows you to lock the system so that none of yourinformation on the system can be accessed until it is unlocked with thecorrect PIN.1. Press Menu > Vehicle > Valet Mode.2. S...

Voice Settings Customize the level of system interaction, help and feedback. Press Menu > Settings > Voice. Voice settings Interaction Mode Standard interaction mode provides moredetailed interaction and guidance.Advanced mode has less audible interactionand more tone prompts. ConfirmationProm...

• Gracenote Media Management on/off: When turned on, this feature will pull in metadata information from the Gracenote Database for yourmusic files. This will override information from your device. Thisfeature defaults to off. • Gracenote Cover Art on/off: When turned on, this feature will pull in c...

To access, press Menu > Settings > Wireless and Internet > Wi-Fisettings, then select from the following options: If you select: You can: Wi-Fi Network(Client) Mode On/Off Turn the Wi-Fi feature on or off in yourvehicle. Make sure that On is selected forconnectivity purposes. Choose a Wirel...

Help! Your touchscreen system has a help feature which you can access at anytime. To access Help using the touchscreen, press Menu > Help, the choosefrom the following: If you select: You can: Where Am I? View the vehicle’s current location.If your vehicle is equipped with navigation,you see your...

TOUCHSCREEN CLIMATE CONTROLS Press the lower right corner on the touchscreen to access yourclimate control features. Depending on your vehicle line andoption package, your climate screen may look different than what is shown here. A. Power: Touch to turn the system on and off. Outside air cannot ent...

Additional climate control voice commands “Rear Defrost On” “Rear Defrost Off” “Recirc On” “Recirc Off” “Panel On” “Panel Floor On” “Floor On” “Windshield Floor On” “Temperature High” “Temperature Low” “Fan Increase” “Fan Decrease” “Temperature”* “Temperature Increase” “Temperature Decrease” “Temper...

When you are viewing additional information for hotels, cityseekr willalso tell you if the hotel has certain services and facilities using icons: Hotel services and facilities Restaurant 24 Hr Room Service Business Center Fitness Center Handicap Facilities Internet Access Laundry Pool Refrigerator W...

Setting Your Navigation Preferences Select settings for the system to take into account when planning yourroute. Press Menu > Settings > Navigation. When you select: You can: Map Preferences Turn breadcrumbs on and off. Choose how you want to view the turn list(top-to-bottom or bottom-to-top)....

When you select: You can: Avoid Areas Choose areas which you want the system to avoidwhen calculating a route for you. Press Add toselect a category.Once you make a selection, the system tries toavoid the area(s) if possible for all routes. Todelete a selection, choose the listing on thescreen; when...

North up always shows the northern direction to be upward on the screen. 3D map mode provides an elevated perspective of the map. This viewing angle can be adjusted and the map can be rotated 180degrees by dragging your finger along the shaded bar with arrowsat the bottom of the map. Re-centering th...

“NAVIGATION” “Zoom State” “Zoom Street” “Zoom to <Distance>” “Help” *If you have said, “Destination”, you may say any of the commands inthe Destination chart. If your vehicle is equipped with the SD card navigation feature, you havethe ability to enter in a street address using a new feature c...

GENERAL INFORMATION SYNC 姞 End User License Agreement (EULA) • You have acquired a device (“DEVICE”) that includes software licensed by FORD MOTOR COMPANY from an affiliate of Microsoft Corporation(“MS”). Those installed software products of MS origin, as well asassociated media, printed materials, ...

DEVICE downloads licenses for protected content, you agree thatMicrosoft may include a revocation list with the licenses. Contentowners may require you to upgrade the SOFTWARE on your DEVICEto access their content. If you decline an upgrade, you will not be ableto access content that requires the up...

laws and treaties. This EULA grants you no rights to use such content.All rights not specifically granted under this EULA are reserved by MS,Microsoft Corporation, FORD MOTOR COMPANY, third party softwareand service providers, their affiliates and suppliers. Use of any on-lineservices which may be a...

End user notice Microsoft 姞 Windows 姞 Mobile for Automotive Important Safety Information This system Ford SYNC™ contains software that is licensed toManufacturer FORD MOTOR COMPANY by an affiliate of MicrosoftCorporation pursuant to a license agreement. Any removal, reproduction,reverse engineering ...

NavTeq End User License Agreement END USER TERMS The content provided (“Data”) is licensed, not sold. By opening thispackage, or installing, copying, or otherwise using the Data, you agree tobe bound by the terms of this agreement. If you do not agree to theterms of this agreement, you are not permi...

Disclaimer of Liability: NT AND ITS LICENSORS (INCLUDING THEIR LICENSORS AND SUPPLIERS) SHALL NOT BE LIABLE TO YOU INRESPECT OF ANY CLAIM, DEMAND OR ACTION, IRRESPECTIVE OFTHE NATURE OF THE CAUSE OF THE CLAIM, DEMAND OR ACTIONALLEGING ANY LOSS, INJURY OR DAMAGES, DIRECT OR INDIRECT,WHICH MAY RESULT ...

Gracenote 姞 End User License Agreement (EULA) This device contains software from Gracenote, Inc. of 2000 Powell StreetEmeryville, California 94608 (“Gracenote”). The software from Gracenote (the “Gracenote Software”) enables thisdevice to do disc and music file identification and obtain music-relate...

THE GRACENOTE SOFTWARE, EACH ITEM OF GRACENOTE DATA ANDTHE GRACENOTE CONTENT ARE LICENSED TO YOU “AS IS.” NEITHERGRACENOTE MAKES ANY REPRESENTATIONS OR WARRANTIES,EXPRESS OR IMPLIED, REGARDING THE ACCURACY OF ANYGRACENOTE DATA FROM THE GRACENOTE SERVERS OR GRACENOTECONTENT. GRACENOTE COLLECTIVELY AN...

911 Assist™ ...................... 392, 473 A ABS (see Brakes) ..................... 202 Accessing and using yourUSB port .................................... 452 Accessing call history/phonebook during active call ............. 382 Accessing your calendar .......... 473 Accessing your media menufea...