Ford 2012 Taurus v.1- User Manual

SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? Inthis guide, answers to such questions are contained in commentshighlighted by the warning triangle symbol. These comments should beread and observed. Warning symbol...

DATA RECORDING Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, st...

CELL PHONE USE The use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,drivers must not compromise their own or others’ safety when usingsuch equipment. Mobile Communications can enhance personal safetyand security when app...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Standard instrument cluster shown, optional cluster similar Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many...

Solid illumination after the engine is started indicates the on-boarddiagnostics system (OBD-II) has detected a malfunction. Refer to On-board diagnostics (OBD-II) in the Maintenance and Specifications chapter. If the light is blinking, engine misfire is occurring which coulddamage your catalytic co...

Low fuel (RTT): Illuminates when the fuel level in the fuel tank is ator near empty. Refer to Fuel gauge in this chapter. Low washer fluid (RTT): Illuminates when the washer level inthe washer fluid reservoir is low. Door ajar (RTT): Illuminates in the message center display whenthe ignition is in t...

Low tire pressure warning: Illuminates when your tire pressureis low. If the light remains on atstart up or while driving, the tirepressure should be checked. Referto Inflating your tires in the Tires, Wheels and Loading chapter. When the ignition is first turned to on, the light will illuminate for...

High beams: Illuminates when the high beam headlamps are turned on. Heads up display (if equipped): A red bar will illuminate on thewindshield in certain instances whenusing adaptive cruise control and/orthe collision warning system. It willalso illuminate momentarily whenyou start your vehicle to m...

Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, the engine is overheating. Stopthe vehicle as soon as safelypossible, switch off the engineand let the engi...

MPG (L/km) This displays instantaneous fuel economy as a bar graph ranging from ↓ poor economy to ↑ excellent economy. Your vehicle must be moving to calculate instantaneous fuel economy.When your vehicle is not moving, this function shows ↓ , one or no bars illuminated. Instantaneous fuel economy c...

COLLISION WARN GAP (if equipped) This allows you to adjust the sensitivity setting of the collision warningsystem. See Collision Warning System in the Driving chapter for more information. Press RESET to change the sensitivity setting. COLLISION WARN CHIME (if equipped) This feature warns the driver...

TIRE MOBILITY KIT EXP 1, 2, 3, 4 YR (if equipped) Use this feature to set the expiration date that is listed on the tiremobility kit sealant canister. See Temporary mobility kit in the Roadside Emergencies chapter for more information on the expiration date. Press the RESET control to choose the pro...

TIRE PRESSURE SENSOR FAULT — Displayed when a tire pressure sensor is malfunctioning, or your spare tire is in use. For moreinformation on how the system operates under these conditions, refer to Tire Pressure Monitoring System (TPMS) in the Tires, Wheels and Loading chapter. If the warning stays on...

CRUISE OVERRIDE (if equipped) — Displayed when the accelerator pedal is being pressed while ACC is active. CRUISE NOT AVAILABLE (if equipped) — Displayed when a system malfunction is preventing ACC from engaging. CRUISE MALFUNCTION (if equipped) — Displayed when a radar malfunction is preventing the...

AUDIO SYSTEMS AM/FM CD/MP3 satellite compatible sound system WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that maytake their focus off the road. Your primary re...

CD/MP3 Player CD: Press to enter CD/MP3 mode. If a disc is already loaded into thesystem, CD/MP3 play will beginwhere it ended last. If no CD is loaded, NO DISC will appear in thedisplay. LOAD:For a single CD system– This control is not operational. To load aCD, simply insert the disc, label side up...

MEMORY PRESETS (0–9): There are 30 available presets, 10 each forSAT1, SAT2 and SAT3. To savesatellite channels in your memory presets, tune to the desired channelthen press and hold a memory preset number (0–9) until sound returns. TEXT: Press and release to display the artist and song title. While...

• CHANNEL LOCKOUT MENU- Press OK to enter the Channel Lockout menu. Press the SEEK to scroll through the following options: a. LOCK/UNLOCK THIS CHANNEL: Press OK when LOCK/UNLOCK THIS CHANNEL is displayed and the display will readENTER PIN. Enter your four-digit PIN number (initial PIN is 1234)and t...

SPEED COMPENSATED VOLUME: With this feature on, radio volume automatically gets louder with increasing vehicle speed to compensatefor road and wind noise. The default setting is off. Use SEEK to adjust between SPEED OFF and levels 1–7: Increasing the level from 1 (lowest setting) to 7 (highest setti...

Auxiliary input jack (Line in) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that maytake their focus off the road. Your primary responsibility is the safeoperat...

USB port (if equipped) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that maytake their focus off the road. Your primary responsibility is the safeoperation of t...

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommended that homemadeCDs be identified withpermanent felt tip marker ratherthan adhesive labels. Ballpoint pens may damage CDs. Pleasecontact your authori...

Sample MP3 structure If you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variousfiles may be present, (files withextensions other than mp3), onlyfiles with the .mp3 extension will beplayed. Other files will be ignoredby the syst...

Radio Display Condition Action Required NO TEXT Category information not available. Category information not available at this time on this channel. The system is working properly. NO SIGNAL Loss of signal from the SIRIUS 威 satellite or SIRIUS 威 tower to the vehicle antenna. You are in a location th...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) Temperature conversion: To switch between Fahrenheit and Celsius, refer to Message center in the Instrument Cluster chapter. 1. Defrost: Distributes outside air through the windshield defroster vents and de-mister vents. Can be used to clear th...

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL(IF EQUIPPED) Temperature conversion: To switch between Fahrenheit and Celsius, refer to Message center in the Instrument Cluster chapter. 1. + Fan speed control: Press to increase the fan speed. 2. Defrost: Distributes outside air through the windshield defros...

VOICE COMMANDS IN CLIMATE MODE Please refer to the Voice commands in climate mode section of the Navigation supplement for more information on using voice commands with the climate control system. Operating tips • To reduce fog build-up on the windshield during humid weather,select (defrost). • To r...

To increase airflow to the outer instrument panel vents, close the ventslocated in the middle of the instrument panel. REAR WINDOW DEFROSTER R The rear defroster control is located on the climate control panel andworks to clear the rear window of fog and thin ice. The ignition must be on to operate ...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the low beam headlamps on. Autolamp control The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the headlamp...

4. Turn the headlamp control to the autolamp position. The headlampswill turn on. 5. Wait the desired amount of time for the exit delay you want (up tothree minutes), then turn the headlamps off. High beams Push the lever toward theinstrument panel to activate. Pullthe lever towards you to deactivat...

Scenario 3: Conditions - The automatic high beam system is set to ON in the message center. The headlamp switch is in (off), (park lamps), or (on). Operation - The high beam switch can be used to turn the high beams on and off. Scenario 4: Conditions - The automatic high beam system is set to OFF in...

INTERIOR LAMPS Front row map lamps The map lamps are located on theoverhead console. Press the controlson either side of each map lamp toturn on the lamps. The map lampsalso light when: • any door is opened. • the instrument panel dimmerbutton is pressed until thecourtesy lamp comes on. • the remote...

The lights come on whenever the ignition is in either the on or accessoryposition and the headlamps or parking lamps are on. Note: The ambient lights will stay on until the ignition is placed in the off position and either of the front doors are opened or the accessorydelay timer expires. BULB REPLA...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate toward you to decrease thespeed of the wipers. Rain-sensing wipers (ifequipped): The rain-sensing wipers will automatically activate whenmoisture is present on thewindshield a...

Courtesy wipe feature: One extra wipe will occur a few seconds after washing the front window to clear any excess washer fluid remaining onthe windshield. Note: Do not operate the washer when the washer reservoir is empty. This may cause the washer pump to overheat. Check the washer fluidlevel frequ...

ILLUMINATED VISOR MIRROR Lift the mirror cover to turn on thevisor mirror lamp. Slide-on-rod feature Rotate the visor towards the sidewindow and extend it rearward foradditional sunlight coverage. Note: To stow the visor back into the headliner, visor must beretracted before moving it backtoward the...

ELECTRONIC COMPASS (IF EQUIPPED) The compass heading is displayed in the center integrated display (CID). The compass reading may be affected when you drive near largebuildings, bridges, power lines and powerful broadcast antenna. Magneticor metallic objects placed in, on or near the vehicle may als...

4. Press and release the 7 and 9radio preset buttons together,repeatedly until ZONE XX changesto the correct zone (1–15) in theCID. 5. The direction will display afterthe buttons are released. The zoneis now updated. Compass calibration adjustment Perform compass calibration in an open area free fro...

CENTER CONSOLE Your vehicle may be equipped with a variety of console features. Note: The appearance and features of the center console may be different thanshow based on your vehicle’s option level. These include: • Cupholders • Utility compartment with audioinput jack, USB port and powerpoint • Pe...

POWER WINDOWS WARNING: Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure themselves. WARNING: When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in t...

• If or is pressed during the opening operation, both windows and moon roof movement will stop. Note: The ignition must be in the off position and the accessory delay feature must be not activated in order for this feature to operate. Note: To disable this feature, contact your authorized dealer. Bo...

INTERIOR MIRROR The interior rearview mirror has two pivot points on the support armwhich lets you adjust the mirror up or down and from side to side. WARNING: Do not adjust the mirror while the vehicle is in motion. Automatic dimming interior rear view mirror (if equipped) The interior rear view mi...

EXTERIOR MIRRORS Power side view mirrors WARNING: Do not adjust the mirror while the vehicle is in motion. To adjust your mirrors: 1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror. 2. Move the control in the directionyou wish t...

Fold-away mirrors Fold the side mirrors in carefullywhen driving through a narrowspace, like an automatic car wash. Blind spot mirrors (if equipped) Your vehicle may be equipped with blind spot mirrors or a blind spotinformation system. Refer to Blind spot mirrors or Blind spot information system (B...

SPEED CONTROL With speed control set, you can maintain a set speed without keepingyour foot on the accelerator pedal. WARNING: Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved. Using speed control The speed controls are located on the steering wheel. Th...

WARNING: Always pay close attention to changing road conditions, especially when using Adaptive Cruise Control. Adaptive Cruise Control cannot replace attentive driving. Failing tofollow any of the warnings below or failing to pay attention to the roadmay result in a collision, serious injury or dea...

3. Press and release the SET +control. The vehicle speed will bestored in the memory and themessage center will display SETXXX MPH (your desired speed). 4. Take your foot off the acceleratorpedal. 5. The green cruise indicator light on the instrument cluster willilluminate if there are no vehiclesde...

Blocked sensor If a message regarding a blockedsensor is displayed, the radar signalsfrom the sensor have beenobstructed. The sensor is locatedbehind a fascia cover near the driverside of the lower grille. When theradar signals are obstructed, avehicle ahead cannot be detectedand the ACC will not fu...

WARNING: Do not use ACC when towing a trailer with brake controls. Aftermarket trailer brakes will not function properly when ACC is activated because the brakes are electronically controlled.Failing to do so may result in loss of vehicle control, which could resultin serious injury. WARNING: Do not...

SYNC 威 system hands-free control feature (if equipped) Press briefly to use the voice command feature. You will hear atone and LISTENING will appear inthe radio display. Press andhold to exit voice command. Press to activate phone mode or answer a phone call. Press andhold to end a call or exit phon...

To open the moon roof: Press and release the SLIDE control, the moonroof will open automatically. Pressthe switch again to stop the moonroof. WARNING: When closing the moon roof, you should verify that it is free of obstructions and ensure that children and/or pets are not in the proximity of the mo...

6 to complete programming of a rolling code equipped device (most commonly a garage door opener). 4. At the garage door opener receiver (motor-head unit) in the garage,locate the “learn” or “smart” button (usually near where the hangingantenna wire is attached to the unit). 5. Firmly press and relea...

Operating the HomeLink 姞 Wireless Control System To operate, simply press and releasethe appropriate HomeLink 威 button. Activation will now occur for thetrained product (garage door, gateoperator, security system, entrydoor lock, or home or office lightingetc.). For convenience, thehand-held transmi...

POSITIVE RETENTION FLOOR MAT WARNING: Always use floor mats that are designed to fit the foot well of your vehicle.Only use floor mats that leave thepedal area unobstructed. Only usefloor mats that are firmly securedto retention posts so that theycannot slip out of position andinterfere with the ped...

TRUNK RELEASE To open the trunk from insidethe vehicle: Press the trunk release buttonlocated on the instrument panelnear the radio. To open the trunk with theoutside release button (vehiclesequipped with intelligent accesskey): 1. Unlock the trunk with thetransmitter or power door lockcontrol. If t...

KEYS Integrated keyhead transmitters (IKTs) (if equipped) Your vehicle may be equipped withtwo integrated keyhead transmitters(IKTs). The key blade is used tostart the vehicle and unlock/lock thedriver’s door from outside thevehicle. The transmitter portionfunctions as the remote entrytransmitter. Y...

MYKEY 姞 The MyKey 威 feature allows you to program a restricted driving mode to promote good driving habits. All but one of the keys programmed to thevehicle can be activated as a MyKey 威 . The key will remain restricted until MyKey 威 is cleared. Any remaining keys are referred to as an “administrato...

5. Press SETUP to enter your choice. The next optional setting will bedisplayed. 6. Repeat Steps 4 and 5 until you are done changing the optionalsettings. Clear MyKey 威 To reset all MyKeys 威 as admin keys, do the following: 1. Turn the vehicle on using the admin key. 2. Press SETUP until PRESS RESET...

POWER DOOR LOCKS • Press the control to unlock all doors. • Press the control to lock all doors. Smart unlocks This feature helps to prevent you from locking yourself out of the vehicleif your key is still in the ignition. When you open one of the front doors and you lock the vehicle with thepower d...

REMOTE ENTRY SYSTEM The intelligent access keys (IA key) comply with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,includin...

Intelligent access (if equipped) Your vehicle will allow you to unlock and enter your vehicle withoutactively using a key or transmitter. You can use the Intelligent Accessfeature at the driver door or at the trunk. You can activate the intelligentaccess feature as long as you have one of your intel...

2. Press and release again within three seconds to unlock all the doors. The turn signals will flash. The remote entry system activates the illuminated entry feature; thisfeature turns on the lamps for 25 seconds or until the ignition is turnedon. The battery saver feature will turn off the lamps 10...

Sounding a panic alarm Press to activate the alarm. The horn will sound and the turn lamps will flash for a maximum of three minutes. Press again or turn theignition to the on position to deactivate, or wait for the alarm to time outin three minutes. Note: The panic alarm will only operate when the ...

• Vertically mounted • Horizontally mounted 2. Press and hold button 1 for five seconds. A tone will be heard aftertwo seconds confirming memory position has been set. Continue to holduntil a second tone is heard after five seconds. 3. Within three seconds press . 4. Wait 10 seconds, then press . 5....

2. Remove the old battery. Note: Please refer to local regulations when disposing oftransmitter batteries. 3. Insert the new battery. Refer tothe instructions inside the IA keyfor the correct orientation of thebattery. Press the battery down toensure that the battery is fullyseated in the battery ho...

The lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. Illuminated exit When all vehicle doors are closed, the ignition is turned off and the keyis removed from the ignition (IKT only), the interior dome lamps,parking lamps and the puddle lamps (i...

SECURICODE™ KEYLESS ENTRY SYSTEM The keypad, located near the driver’s window, is invisible until touchedand then it lights up so you can see and touch the appropriate buttons. Note: If you enter your entry code too fast on the keypad, the unlock function may not work. Re-enter your entry code more ...

Note: Touching 5 • 6, 7 • 8, or 9 • 0 keypad numbers as a sixth digit will not recall a driver memory setting. Note: The factory-set code cannot be associated with a memory setting. 5. The doors will lock then unlock to confirm that your personal entrycode has been programmed to the module. Tips: • ...

Note: If equipped with intelligent access, if the intelligent access key is within 3 feet (1 meter) of the driver door, your keyless entry keypadcode will still function the same way, but the driver’s door will alsounlock with each keypad button press. To open the trunk, enter the factory set code o...

Anti-theft indicator The anti-theft indicator is located in the instrument panel cluster. • When the ignition is off, theindicator will flash once every twoseconds to indicate theSecuriLock 威 system is functioning as a theft deterrent. • When the ignition is on, the indicator will glow for three sec...

2. Turn the ignition from off to on. Keep the ignition on for at least threeseconds, but no more than 10 seconds. 3. Turn the ignition off and remove the first coded key from the ignition. 4. After three seconds but within ten seconds of turning the ignition off,insert the second previously coded ke...

FRONT SEATS WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. WARNING: Before...

Properly adjust the head restraint so that the top of the head restraint iseven with the top of your head and positioned as close as possible to theback of your head. For occupants of extremely tall stature, adjust thehead restraint to its full up position. WARNING: To minimize the risk of neck inju...

Lift handle to move seat forward orbackward. Pull lever up to adjust seatback. WARNING: Before returning the seatback to its original position, make sure thatcargo or any objects are nottrapped behind the seatback. Afterreturning the seatback to itsoriginal position, pull on theseatback to ensure th...

Adjusting the front power seat (if equipped) WARNING: Never adjust the driver’s seat or seatback when the vehicle is moving. WARNING: Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. WARNING: Always drive and ride with your seatback upright and ...

• Continue pressing the control for approximately two seconds; you willfeel the seat bounce back slightly. Using the power lumbar support (if equipped) The power lumbar control is locatedon the outboard side of the seat. Press one side of the control toadjust firmness. Press the other side of the co...

Note: Do not do the following: • Place heavy objects on the seat • Operate the seat heater if water or any other liquid is spilled on theseat. Allow the seat to dry thoroughly. To operate the heated seats: Press the heated seat symbol/buttonto cycle through the various heatsettings and off. Warmer s...

Cooled seats The cooled seats will only function when the engine is running. To operate the cooled seats: Press the cooled seat symbol/buttonto cycle through the various coolingsettings and off. Cooler settings areindicated by more indicator lights. If the engine falls below 350 rpm while the cooled...

To remove an air filter: 1. Turn the vehicle off. 2. Push up on the outside rigid edgeof the filter until the tabs arereleased, then rotate the air filtertoward the front of the vehicle. 3. Remove filter. To install a filter: 1. First, position the filter in itshousing making sure that the farforwar...

Memory seats/power mirrors/adjustable pedals (if equipped) This system allows automatic positioning of the driver seat, powermirrors, and adjustable pedals to two programmable positions. The memory seat control is located on the seat side shield. The buttonsmay be configured either horizontally or v...

To remove the non-adjustable head restraint, do the following: 1. Simultaneously press and holdboth unlock/remove buttons, thenpull up on the head restraint. To reinstall the non-adjustable head restraint, do the following: 1. Insert the two stems into theguide sleeve collars. 2. Push the head restr...

WARNING: To minimize the risk of neck injury in the event of a crash, head restraints must be installed properly. Split-folding rear seat One or both rear seatbacks can be folded down to provide additionalcargo space. To lower the seatback(s) frominside the vehicle, pull the straplocated on the outb...

The heated seats only operate when the ignition is on. To operate theheated seats: • Press the indicated side of thecontrol for maximum heat. • Press again to deactivate. • Press the indicated side of thecontrol for minimum heat. • Press again to deactivate. The heated seat module resets at every ig...

• Restraints Control Module (RCM) with impact and safing sensors. • Restraint system warning light and back-up tone. • The electrical wiring for the airbags, crash sensor(s), safety beltpretensioners, front safety belt usage sensors, driver seat positionsensor, front passenger sensing system, and in...

Driver’s seat position sensor The driver’s seat position sensor allows your Personal Safety System totailor the deployment level of the driver dual-stage airbag based on seatposition. The system is designed to help protect smaller drivers sittingclose to the driver airbag by providing a lower airbag...

Front safety belt pretensioners The safety belt pretensioners at the front outboard seating positions aredesigned to tighten the safety belts firmly against the occupant’s bodyduring frontal collisions, and in side collisions and rollovers. This helpsincrease the effectiveness of the safety belts. I...

WARNING: Front and rear seat occupants, including pregnant women, should wear safety belts for optimum protection in an accident. Combination lap and shoulder belts 1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until you hear a snap and...

Pregnant women should alwayswear their safety belt. The lap beltportion of a combination lap andshoulder belt should be positionedlow across the hips below the bellyand worn as tight as comfort willallow. The shoulder belt should bepositioned to cross the middle ofthe shoulder and the center of thec...

How to use the automatic locking mode 1. Buckle the combination lap andshoulder belt. 2. Grasp the shoulder portion andpull downward until the entire beltis pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the auto...

Safety belt height adjustment Your vehicle has safety belt heightadjustments for the front outboardseating positions. Adjust the height of the shoulderbelt so the belt rests across themiddle of your shoulder. To adjust the shoulder belt height,squeeze the button and slide theheight adjuster up or do...

If... Then... The driver’s or frontpassenger’s safety belt becomesunbuckled for approximately1 minute while the vehicle istraveling at least 3 mph(5 km/h) and more than1-2 minutes have elapsed sincethe ignition has been switchedon... The Belt-Minder 威 feature is activated - the safety belt warning l...

Reasons given... Consider... “Traffic is light” Nearly 1 of 2 deaths occur insingle-vehicle crashes, many when no other vehicles are around. “Belts wrinkle my clothes” Possibly, but a serious crash can domuch more than wrinkle your clothes,particularly if you are unbelted. “The people I’m with don’t...

• This will enable the Belt-Minder 威 feature for that seating position if it is currently disabled. As confirmation, the safety belt warning light willflash four times per second for three seconds, followed by threeseconds with the light off, then followed by the safety belt warninglight flashing fo...

Important supplemental restraint system precautions Airbags DO NOT inflate slowly orgently and the risk of injury from adeploying airbag is greatest close tothe trim covering the airbag module. WARNING: All occupants of the vehicle, including the driver, should always properly wear their safety belt...

How does the airbag supplemental restraint system work? The airbag SRS is designed toactivate when the vehicle sustainslongitudinal deceleration sufficientto cause the sensors to close anelectrical circuit that initiates airbaginflation. The fact that the airbagsdid not inflate in a collision does n...

• the system determines that an infant is present in a rear-facing infantseat that is installed according to the manufacturer’s instructions, • the system determines that a small child is present in a forward-facingchild restraint that is installed according to the manufacturer’sinstructions, • the ...

WARNING: To reduce the risk of possible serious injury: Do not stow objects in seat back map pocket (if equipped) or hang objects off seat back if a child is in the front passenger seat.Do not place objects underneath the front passenger seat or betweenthe seat and the center console (if equipped).C...

WARNING: Any alteration/modification to the front passenger seat may affect the performance of the front passenger sensing system. Determining if the system is operational The supplemental restraint system uses a warning indicator light in theinstrument cluster or a backup tone to indicate the condi...

WARNING: Do not attempt to service, repair, or modify the Safety Canopy 威 system, its fuses, the A, B, or C pillar trim, or the headliner on a vehicle containing a Safety Canopy 威 . See your authorized dealer. WARNING: All occupants of the vehicle including the driver should always wear their safety...

WARNING: If the Safety Canopy system has deployed, the Safety Canopy willnot function again unless replaced.The Safety Canopy system(including the A, B and C pillartrim and headliner) must beinspected and serviced by anauthorized dealer. If the SafetyCanopy is not replaced, it will notfunction again...

• pressing the hazard control button, • or pressing the panic button on the remote entry transmitter. The feature will continue to operate until the vehicle runs out of power. Disposal of airbags and airbag equipped vehicles For disposal of airbags or airbag equipped vehicles, see your authorizeddea...

Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommendedrestraint type Infants ortoddlers Children weighing 40 lb (18 kg) orless (generally age four or younger) Use a child safetyseat (sometimescalled an infantcarrier, convertibleseat, or toddlerseat). Smallc...

Recommendations for attaching child safety restraints for children RestraintType Child Weight Use any attachment method as indicated below by “X” LATCH(loweranchorsandtoptetheranchor) LATCH(loweranchorsonly) Safetybeltandtoptetheranchor Safetybelt andLATCH(loweranchorsand toptetheranchor) Safetybelt...

WARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision, which may result in serious injury ordeath. WARNING: Never use pillows, books, or towels to boost a child. They can slide around and increase ...

Follow all the safety restraint and airbag precautions that apply to adultpassengers in your vehicle. If the child is the proper height, age, and weight (as specified by yourchild safety seat or booster manufacturer), fits the restraint and can berestrained properly, then restrain the child in the c...

Your vehicle has LATCH lower anchors for child seat installation at theseating positions marked with the child seat symbol. The LATCH anchors are located atthe rear section of the rear seatbetween the cushion and seatback,below the locator symbols on theseat back. Follow the child seatmanufacturer’s...

WARNING: Never attach two child safety seats to the same anchor. In a crash, one anchor may not be strong enough to hold two child safety seat attachments and may break, causing seriousinjury or death. Each time you use the safety seat, check that the seat is properlyattached to the lower anchors an...

The tether strap anchors in yourvehicle are in the following positions(shown from top view): Attach the tether strap only to the appropriate tether anchor as shown.The tether strap may not work properly if attached somewhere otherthan the correct tether anchor. Once the child safety seat has been in...

3. Open the tether anchor cover. 4. Clip the tether strap to theanchor as shown. If the tether strap is clippedincorrectly, the child safety seat maynot be retained properly in theevent of a collision. 5. Tighten the child safety seat tether strap according to themanufacturer’s instructions. If the ...

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, and lets you adjust the shoulder belt to cross the chest andrest snugly near the center of the shoulder. The drawings below comparethe ideal fit (cente...

Follow all instructions provided by the manufacturer of the booster seat. WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the riskof injury or death in a collis...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING Tire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperature A These Tire Quality G...

WARNING: Under-inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or “blowout”, with unexpected loss of vehicle control and increasedrisk of injury. Under-inflation increases sidewall flexing and rollingresistance, resulting in heat buildup a...

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, ...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

WARNING: When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautionslisted below. If the beads do not seat at the maximum pressureindicated, re-lubricate and try again.When inflating the ...

• Do not run over curbs or hit the tire against a curb when parking WARNING: If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to fiveseconds. WARNING: Do not spin th...

• Front-wheel drive (FWD) vehicles(front tires at top of diagram) • All-wheel drive (AWD) vehicles(front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel mis...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on aspecified government test course. For example, a tire graded 150would wear one and one-half (1 1 ⁄ 2 ) times as well ...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below. Note: Tire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the Tire a...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Grades donot apply ...

following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that may cause undesired operation. WARNING: The tire pressure monitoring system is NOT a substitute for manually checking tire pressure. The ...

To restore the full functionality of the tire pressure monitoring system,have the damaged road wheel/tire repaired and remounted on yourvehicle. For additional information, refer to Changing tires with a TPMS in this section. When you believe your system is not operating properly The main function o...

Low tirepressurewarning light Possible cause Customer action required Flashingwarning light Spare tire in use Repair the damaged road wheel/tire and reinstall it on the vehicle torestore system functionality. For adescription on how the systemfunctions, refer to When your temporary spare tire is ins...

SNOW TIRES AND CHAINS WARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety andperformance of your vehicle, which could result in an increased risk ofloss of vehicle control, ve...

SUMMER TIRES Your Taurus SHO may be equipped with summer tires to providesuperior performance on wet and dry roads. Summer tires do not havethe Mud and Snow (M+S or M/S) tire traction rating on the tire sidewall. Since summer tires do not have the same traction performance asAll-season or Snow tires...

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-Pillar or the edge of the driver’s door(vehicles exported outside the US and Canada may not have a TireLabel). Look for “THE COMBINED WEI...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loadweight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb wei...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

• Example only: WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structuraldamage, serious damage to the vehicle, loss of control and personalinjury. Tires, Wheels and Lo...

GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo andpassengers – that the vehicle can handle without r...

Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that willbe riding in your vehicle. 3. Subtract the combin...

WARNING: Do not operate Adaptive Cruise Control (ACC) when towing a trailer equipped with brakes. Aftermarket trailer brakes will not function properly when ACC is activated, which maylead to loss of vehicle control, increasing the risk of serious injury. The braking system of the tow vehicle is rat...

Trailer towing tips • Practice turning, stopping and backing-up before starting on a trip toget the feel of the vehicle-trailer combination. When turning, makewider turns so the trailer wheels will clear curbs and other obstacles. • To aid in engine/transmission cooling and A/C efficiency during hot...

STARTING Positions of the ignition (if equipped) If your vehicle is equipped with a push button start system, refer to Push button start system in this section for ignition modes. 1. Off— locks the gearshift leverand allows key removal. Thisposition also shuts the engine andall electrical accessorie...

3. After idling for a few seconds, release the parking brake, apply thebrake, shift into gear and drive. Note: If the engine does not start on the first try, turn the vehicle to the off position, wait 10 seconds and try Step 2 again. If the engine still failsto start, press the accelerator to the fl...

Fast Restart Feature: The Fast Restart feature allows you to re-start your vehicle within 20 seconds of switching the vehicle off, if a valid IAkey is not present when the vehicle is switched off. When you switchyour vehicle off without an IA key in the passenger compartment ortrunk, the message RES...

Important ventilating information If the engine is idling while the vehicle is stopped for a long period oftime, open the windows at least 1 inch (2.5 cm) or adjust the heating orair conditioning to bring in fresh air. ENGINE BLOCK HEATER (IF EQUIPPED) WARNING: Failure to follow engine block heater ...

Even when the ABS is disabled,normal braking is still effective. Ifyour BRAKE warning lampilluminates with the parking brakereleased, have your brake systemserviced immediately. Brake over accelerator This vehicle is equipped with a brake over accelerator feature. In theevent the accelerator pedal b...

Electronic stability control (ESC) Electronic stability control (ESC) may enhance your vehicle’s directionalstability during adverse maneuvers, for example when cornering severelyor avoiding objects in the roadway. Electronic stability control operatesby applying brakes to one or more of the wheels ...

AdvanceTrac 威 Features Controlfunctions Mode Stability control off light Message center display ESC TCS Default atstart-up System Initialization Turns on during bulb check Nothing displayed Enabled Enabled Controlpressedonce Traction control OFF On TRACTION CONTROL OFF Enabled Disabled Controlpresse...

STEERING 3.5L V6 engine (SHO): Your vehicle is equipped with an electric power steering (EPS) system. There is no fluid reservoir to check or fill. If your vehicle loses electrical power while you are driving (or if theignition is turned off), you can steer the vehicle manually, but it takesmore eff...

3.5L V6 engine: Your vehicle is equipped with a hydraulic steering system. To help prevent damage to the power steering system, never hold thesteering wheel at its furthest turning points (until it stops) for more thana few seconds when the engine is running. If the power steering systembreaks down ...

R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward.Always come to a complete stop before shifting into and out of R(Reverse). N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this p...

M (Manual) With the gearshift lever in M(Manual), the driver can changegears up or down (without a clutch)as desired. This is called SelectShiftAutomatic™ transmission (SST)mode. By moving the gearshift leverfrom drive position D (Drive) to M(Manual) you now have control ofselecting the gear you des...

Recommended shift speeds Upshift according to the following chart: Upshifts when accelerating (recommended for best fuel economy) Shift from: 1 - 2 15 mph (24 km/h) 2 - 3 25 mph (40 km/h) 3 - 4 40 mph (64 km/h) 4 - 5 45 mph (72 km/h) 5 - 6 50 mph (80 km/h) The instrument cluster will show thecurrent...

• (1) Rear bumper • (2) Red zone • (3) Yellow zone • (4) Green zone Always use caution while backing. Objects in the red zone are closest to your vehicle and objects in thegreen zone are further away. Objects are getting closer to your vehicle asthey move from the green zone to the yellow or red zon...

WARNING: This system is designed to be a supplementary driving aid. It is not intended to replace the driver’s attention, and judgment, or the need to apply the brakes. This system does NOTactivate the brakes automatically. Failure to press the brake pedal toactivate the brakes may result in a colli...

BLIND SPOT MIRRORS (IF EQUIPPED) Blind spot mirrors have an integrated convex spotter mirror built intothe upper outboard corner of the outside mirrors. They are designed toassist the driver by increasing visibility along the side of the vehicle. Formore information on your side view mirrors, refer ...

BLIND SPOT INFORMATION SYSTEM (BLIS 姞 ) WITH CROSS TRAFFIC ALERT (CTA) (IF EQUIPPED) The BLIS 威 is a convenience feature that aids the driver in assessingwhether a vehicle is within an areaon either side of the vehicleextending rearward from the outsidemirrors to approximately 10 feet(3 meters) beyo...

Cross traffic alert (CTA) system operation The CTA system warns the driver of approaching vehicles when R(Reverse) is selected and the vehicle is backing out of a front-in parkingspot. It sounds a series of tones and flashes the BLIS 威 indicator found on the exterior mirror on the side of the approa...

CTA coverage also decreases when parking at shallow angles (refer tofigure for approximate zone coverage areas [sensor obstructed for vehicle on left] ). CTA detection limitations: Due to the nature of radar technology, there may be certain instances where vehicles entering and exiting theblind spot...

CTA and reverse sensing system (RSS) interaction CTA works along with the reverse sensing system (RSS) (if equipped).Become familiar with the warning tones of both systems. BLIS 威 and/or CTA on/off and disable operation The BLIS 威 and/or the CTA can be turned off via the message center. If either th...

WARNING: Just prior to the system recognizing a blocked condition and alerting the driver, the number of missed objects will increase. To help avoid injuries, NEVER use the BLIS 威 as a replacement for using the side and rear view mirrors and looking overyour shoulder before changing lanes. BLIS 威 is...

driving surfaces are relatively level, obstruction-free and otherwisesimilar to normal on-road driving conditions. Operating your vehicleunder other than those conditions could subject the vehicle to excessivestress which might result in damage which is not covered under yourwarranty. Driving on sli...

Your vehicle is equipped with Traction Control™, it may be beneficial todisengage the Traction Control™ system while attempting to rock thevehicle. Do not rock the vehicle if the engine is not at normal operatingtemperature or damage to the transmission may occur. Do not rock the vehicle for more th...

Driving through deep water may damage the engine ortransmission. If the front or rear axle is submerged in water, the axle lubricant andPTU (Power Transfer Unit) lubricant should be checked and changed ifnecessary. After driving through mud, clean off residue stuck to rotating driveshaftsand tires. ...

Maintenance and modifications The suspension and steering systems on your vehicle have been designedand tested to provide predictable performance whether loaded or emptyand durable load carrying capability. For this reason, Ford MotorCompany strongly recommends that you do not make modifications suc...

ROADSIDE ASSISTANCE Vehicles sold in the U.S. : Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24-hours,...

Vehicles sold in the U.S. : Using roadside assistance Complete the roadside assistance identification card and place it in yourwallet for quick reference. This card is found in the Owner’s Guideportfolio in the glove compartment. U.S. Ford vehicle customers who require Roadside Assistance, call1-800...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

Passenger compartment fuse panel The fuse panel is located under the instrument panel to the left of thesteering wheel. The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Protected Circuits 1 30A Left front power window, Smartwindow motor 2 15A Brake on/off switch 3 15A Driver power...

Fuse/Relay Location Fuse Amp Rating Protected Circuits 29 5A Instrument panel cluster,Heads-up display 30 5A Not used (spare) 31 10A Not used (spare) 32 10A Airbag module 33 10A Not used (spare) 34 5A Anti-lock brake system (ABS),Electronic power steering 35 10A Rear heated seats, AWD, Rearpark assi...

Power distribution box The power distribution box is located in the engine compartment. Thepower distribution box contains high-current fuses that protect yourvehicle’s main electrical systems from overloads. WARNING: Always disconnect the battery before servicing high current fuses. WARNING: To red...

Fuse/Relay Location Fuse Amp Rating Power Circuits 59 Half ISO relay Left halogen headlamp relay 60 Half ISO relay Right halogen headlamp relay 61 — Not used 62 — Not used 63 Half ISO relay Daytime running lamps (DRL) 1relay 64 Half ISO relay DRL 2 high beam control relay 65 G8VA relay Run/start rel...

3. Full-size dissimilar spare without label on wheel When driving with the full-size dissimilar spare tire/wheel, do not: • Exceed 70 mph (113 km/h) • Use more than one dissimilar spare tire/wheel at a time • Use commercial car washing equipment • Use snow chains on the end of the vehicle with the d...

Stopping and securing the vehicle 1. Park on a level surface, set theparking brake and activate hazardflashers. 2. Place gearshift lever in P (Park)and turn engine off. Removing the spare tire and jack 1. Lift the trunk cargo cover, andremove the wing nut that securesthe spare tire by turning itcoun...

Tire change procedure WARNING: When one of the front wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the vehicle is in P (Park). WARNING: To help prevent the vehicle from moving when you change a tire, be sure to place the t...

WARNING: To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is onlymeant for changing the tire. 3. Put the jack in the jack notchnext to the tire you are changing.Turn the...

Stowing the tire and jack 1. Fully collapse the jack, fold thelug wrench socket into the handleand place the jack and wrench intothe felt bag as shown. Place theextension bolt into the externalpocket of the felt bag. Take care toposition the jack as shown to ensurethat the locating holes in the jack...

If you are stowing the flat tire: 1. Remove the extension bolt fromthe exterior pocket of the felt bag. 2. Install the jack as shown inStep 4 under Stowing the tire and jack . 3. Screw the extension bolt onto thethreaded stud of the jack retentionbracket. 4. With the temporary spare tire onthe vehic...

• Periodically monitor tire inflation pressure in the affected tire; if thetire is losing pressure, have the vehicle towed. • Read the information in the Tips for use of the temporary mobility kit section to ensure safe operation of the temporary mobility kit and your vehicle. Tips for use of the te...

• When inflating a tire or other objects, use the black air hose only. Donot use the transparent hose which is designed for sealant applicationonly. • Operating the temporary mobility kit could cause an electricaldisturbance in radio, CD, and DVD player operation (if equipped). What to do when a tir...

4. Plug the power cable into the 12Vpower point in the vehicle. 5. Remove the warning sticker found on the canister and place it on thetop of the instrument panel or the center of the dash. 6. Start the engine (only if the vehicle is outdoors or in a well-ventilated area) . 7. Turn dial (1) counterc...

Note: When the sealing compound is first added into the tire, theair pressure gauge reading on the compressor unit may indicate ahigher value; this is normal and should be no reason for concern.The pressure will drop after about 30 seconds of operation. Thetire pressure has to be checked with the co...

3. Turn the dial clockwise to the air position. Turn on the kit by pressingthe on/off button. 4. Adjust the tire to therecommended inflation pressurefrom the tire label located on thedriver’s door or door jamb area.Pressing the deflation button nearthe sealant canister removes airfrom the tire. Note...

Removal of the sealant canister from the temporary mobility kit 1. Unwrap the clear tube from thecompressor housing. 2. Press the button located on thetemporary mobility kit compressorhousing below the canister whilepulling up on the sealant canister. Installation of the sealant canister to the temp...

WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the specified torque within 100 miles (160 km)after any wheel disturbance (rotation, flat tire, wheel removal, etc.). Lug nut socket size/Bolt size Wheel lug nut torque* ft-lb N • m 1 ⁄ 2 x 20 100 135 * Torque specifications are for nut a...

Connecting the jumper cables Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery. 1. Connect the positive (+) jumpercable to the positive (+) terminal ofthe discharged battery. 2. Connect the other end of thepositive (+) cable to the positive(+)...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery. 1. Remove the jumper cable fromthe ground metal surface. 2. Remove the jumper cable on thenega...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift anddollies or flatbed equipment. Do not tow w...

If the vehicle is towed by other means or incorrectly, vehicledamage may occur. Ford Motor Company produces a towing manual for all authorized towtruck operators. Have your tow truck operator refer to this manual forproper hook-up and towing procedures for your vehicle. Emergency towing In case of a...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizeddealer. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfaction. Plea...

In Canada: Mailing address Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Additional assistance If you have questions or concerns, or are unsatisfied with the service youare receiving, follow ...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft 威 Detail Wash (ZC-3-A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can ...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with ...

PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your authorized dealer. • For routine cleaning, use Motorcraft 威 Detail Wash (ZC-3-A). • If tar or grease spots are present, use Motorcraft 威 Bug and Tar Remover (ZC-42). WINDOWS ...

INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENS Clean the instrument panel, interior trim areas and cluster lens with aclean, damp, white cotton cloth, then use a clean and dry white cottoncloth to dry these areas. • Avoid cleaners or polishes that increase the gloss of the upper portionof the instr...

INTERIOR For fabric, carpets, cloth seats, safety belts and seats equipped with sideairbags: • Remove dust and loose dirt with a vacuum cleaner. • Remove light stains and soil with Motorcraft 威 Professional Strength Carpet & Upholstery Cleaner (ZC-54). • If grease or tar is present on the materi...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide to find out wh...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column. 2. Go to the front of the vehicle andrelease the auxiliary latch that islocated under the front center ofthe hood. 3. Lift the hood. Maintenance and Specificat...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.5L V6 engine 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Brake fluid reservoir 4. Battery 5. Power distribution box 6. Air filter assembly 7. Automatic transmission fluid dipstick 8. Engine oil dipstick 9. Engine oil filler cap ...

Engine shield Some vehicles may be equipped with an aero-shield under the engine.This shield needs to be removed for service, including oil and filterchanges. It is secured with four quick release fasteners. WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold wea...

CHANGING THE WIPER BLADES 1. Pull the wiper blade and armaway from the glass. 2. Squeeze the locking tabs torelease the blade from the arm andpull the blade away from the arm toremove it. 3. Attach the new blade to the arm and snap it into place. Replace wiper blades at least once per year for optim...

5. Locate and carefully remove theengine oil level dipstick. 6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again. • If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added to raise the...

2. If the engine oil level is not within the normal operating range, addonly certified engine oil of the recommended viscosity. Remove theengine oil filler cap and use a funnel to pour the engine oil into theopening. 3. Recheck the engine oil level. Make sure the oil level is not above thenormal ope...

Ford production and Motorcraft 威 replacement oil filters are designed for added engine protection and long life. If a replacement oil filter is usedthat does not meet Ford material and design specifications, start-upengine noises or knock may be experienced. It is recommended you use the appropriate...

WARNING: When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle orbattery. Lift the battery with a battery carrier or with your hands onopposite corners. WARNING: Keep batteri...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant sho...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the FULL COLD level, or within theCOLD FILL or MIN / MAX range as listed on the engine coolantreservoir (depending upon application). • Refer to scheduled maintenance information for serv...

• DO NOT MIX different colors or types of coolant in your vehicle. Make sure the correct coolant is used. Mixing of engine coolants mayharm your engine’s cooling system. The use of an improper coolantmay harm engine and cooling system components and may void thewarranty. Refer to Maintenance product...

3. Step back while the pressure releases. 4. When you are sure that all the pressure has been released, use thecloth to turn it counterclockwise and remove the cap. 5. Fill the coolant reservoir slowly with the proper coolant mixture, towithin the COLD FILL RANGE or the FULL COLD level on the reserv...

Severe climates If you drive in extremely cold climates: • It may be necessary to increase the coolant concentrationabove 50%. • NEVER increase the coolant concentration above 60%. • A coolant concentration of 60% will provide improved freezepoint protection. Increased engine coolant concentrationsa...

• The service engine soon indicator will illuminate. If the engine reaches a preset over-temperature condition, the enginewill automatically switch to alternating cylinder operation. Each disabledcylinder acts as an air pump and cools the engine. When this occurs the vehicle will still operate. Howe...

Refueling WARNING: Fuel vapor burns violently and a fuel fire can cause severe injuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; ...

4. After you are done pumping fuel, slowly remove the fuel fillernozzle—allow about five seconds after pumping fuel before removing thefuel filler nozzle. This allows residual fuel to drain back into the fuel tankand not spill onto the vehicle. Note: A fuel spillage concern may occur if overfilling ...

Cleaner air Ford endorses the use of reformulated “cleaner-burning” gasolines toimprove air quality, per the recommendations in the Choosing the right fuel section. Running out of fuel Avoid running out of fuel because this situation may have an adverseeffect on powertrain components. If you have ru...

1. After lifting the trunk cargocover, locate the white plasticfunnel. It is attached to the rear,lower edge of the spare tirecompartment. 2. Slowly insert the funnel into theEasy Fuel 威 system. 3. Fill the vehicle with fuel from the portable fuel container.4. When done, clean the funnel or properly...

The advertised capacity is the amount of the indicated capacity and theempty reserve combined. Indicated capacity is the difference in theamount of fuel in a full tank and a tank when the fuel gauge indicatesempty. Empty reserve is the small amount of fuel remaining in the fueltank after the fuel ga...

Keep a record for at least one month and record the type of driving (cityor highway). This will provide an accurate estimate of the vehicle’s fueleconomy under current driving conditions. Additionally, keeping recordsduring summer and winter will show how temperature impacts fueleconomy. In general,...

• Perform all regularly scheduled maintenance items. Follow therecommended maintenance schedule and owner maintenance checksfound in scheduled maintenance information. Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economyat any speed. • Carrying unnecessary weight may re...

If other than Ford, Motorcraft 威 or Ford-authorized parts are used for maintenance replacements or for service of components affectingemission control, such non-Ford parts should be equivalent to genuineFord Motor Company parts in performance and durability. WARNING: Do not park, idle, or drive your...

BRAKE FLUID The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the MIN andMAX lines are within the normaloperating range; there is no need toadd fluid. If the fluid levels areoutside of the normal operatingrange, the performan...

C. Remove the bolt cover (ifequipped). D. Remove two bolts that attach the air filter assembly to the front ofthe vehicle (2). E. Loosen the clamp holding the air filter assembly to the rubber hose(1). F. Remove the harness retaining clip by pulling up (3). Do notdisconnect the sensor (4). G. Withou...

AIR FILTER Refer to scheduled maintenance information for the appropriate intervals for changing the air filter element. When changing the air filter element, use only the air filter elementlisted. Refer to Motorcraft 威 part numbers in this chapter. WARNING: To reduce the risk of vehicle damage and/...

4. Wipe the air filter housing and cover clean to remove any dirt ordebris and to ensure good sealing. 5. Install a new air filter element. Be careful not to crimp the filterelement edges between the air filter housing and cover. This could causefilter damage and allow unfiltered air to enter the en...

Brakes • Make sure brakes and parking brake are fully released. Tires • Maintain recommended air pressure. Miscellaneous • Make sure all linkages, cables, levers and pins under vehicle arecovered with grease to prevent rust. • Move vehicles at least 25 feet (8 m) every 15 days to lubricateworking pa...

MOTORCRAFT PART NUMBERS Component 3.5L V6 Engine 3.5L V6 SHO engine Air filter element FA-1884 FA-1884 Battery BXT-59 BXT-65–650 Oil filter FL-500-S FL-500-S Spark plugs SP-411 1 SP-528 1 Cabin air filter FP68 FP68 Windshield wiperblade WW-2601-PF (driver side)WW-2001-PF (passenger side) 1 Refer to ...

ENGINE DATA Engine 3.5L V6 engine 3.5L V6 SHO engine Cubic inches 214 214 Fuel See Octane recommendations earlier in this chapter. See Octane recommendations earlier in this chapter. Firing order 1–4–2–5–3–6 1–4–2–5–3–6 Ignition system Coil on plug Coil on plug Spark plug gap 0.052–0.056 inch (1.32–...

FORD CUSTOM ACCESSORIES FOR YOUR VEHICLE A wide selection of Ford Custom Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement the ...

Peace of mind • Remote start • Vehicle tracking and recovery* • Wheel locks • Locking fuel plug for capless fuel system • Bumper mounted parking sensors* *Ford Licensed Accessories (FLA) are warranted by the accessorymanufacturer’s warranty. Ford Licensed Accessories are fully designedand developed ...

FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY) More than 30 million Ford and Lincoln owners have discovered thepowerful protection of Ford ESP. It is the only extended service planbacked by Ford Motor Company, and provides “peace of mind”protection beyond the New Vehicle Limited Warranty coverage. Up t...

FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY) You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is the only service contractbacked by Ford Motor Company of Canada, Limited. Depending on theplan you purchase, Ford ESP provides benefits such as: • R...

GENERAL MAINTENANCE INFORMATION Why maintain your vehicle? This guide describes the scheduled maintenance required for yourvehicle. Carefully following this schedule helps protect against majorrepair expenses resulting from neglect or inadequate maintenance andmay also help to increase the value of ...

Your vehicle is very sophisticated and built with multiple complexperformance systems. Every manufacturer develops these systems usingdifferent specifications and performance features. That’s why it’simportant to rely upon your dealership to properly diagnose and repairyour vehicle. Ford Motor Compa...

Convenience Many dealerships have extended evening and Saturday hours to makeyour service visit more convenient. How’s that for quality service? Factory-trained technicians Service technicians participate in extensive factory-sponsoredcertification training to help them become experts on the operati...

Normal Scheduled Maintenance At every oil changeinterval as indicatedby the messagecenter Change engine oil and filter Rotate tires, inspect tire wear and measure treaddepth Perform multi-point inspection (recommended) Inspect automatic transmission fluid level (ifequipped with dipstick); consult de...

Maintenance schedule log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ...

SPECIAL OPERATING CONDITIONS If you operate your vehicle primarily in any of the following conditions, you need to perform additional maintenance as indicated. If you occasionally operate your vehicle under any of these conditions, it is not necessary to perform the additional maintenance. For speci...

Perform the services in the preceding table when specified or within3,000 miles (4,800 km) of the OIL CHANGE REQUIRED messageappearing in the message center. Example #1: The OIL CHANGE REQUIRED message comes on at 28,751 miles (46,270 km); perform the 30,000 mile (48,000 km)automatic transmission fl...

Special operating condition log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D A...

EXCEPTIONS There are several exceptions to the Normal Schedule. They are listedbelow: Normal vehicle axle maintenance: Rear axles and power take-off (PTO) units with synthetic fluid and light-duty trucks equipped withFord-design axles are lubricated for life; do not check or change fluidunless a lea...

using oils defined by the American Petroleum Institute (API)performance category of API SK or earlier (for example SJ, etc). Edge/MKX AWD only – vehicles operating off-road in sand during highambient temperatures must replace the AWD PTU (All-wheel drivePower Transfer Unit) lube every 20,000 miles (...

A Accessory delay ..........................84 Adaptive Cruise Control .............89 AdvanceTrac ..............................245 AdvanceTrac Sport Mode .........250 Airbag supplemental restraintsystem ................171–172, 180, 182 and child safety seats ............173description ..............

V Vehicle Identification Number(VIN) ..........................................374 Vehicle loading ..........................223 Ventilating your vehicle ...........241 W Warning lights (see Lights) .......12 Washer fluid ..............................332 Water, Driving through .............279 Wind...