Ford 2012 Fiesta v.3- User Manual

SPECIAL NOTICES New Vehicle Limited Warranty For a detailed description of what is covered and what is not covered byyour vehicle’s New Vehicle Limited Warranty, refer to the Warranty Guide that is provided to you along with your Owner’s Guide. Special instructions For your added safety, your vehicl...

involving the deployment of an airbag or, in certain vehicles, theactivation of the fuel pump shut-off. Certain versions or updatesto 911 Assist may also be capable of being used to electronicallyor verbally provide to 911 operators the vehicle location (such aslatitude and longitude), and/or other ...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Warning lights can alert you to a vehicle condition that may becomeserious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make sure thebul...

WARNING: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possiblycausing a fire. Low fuel: Displays when the fuel level in the fuel tank is at or nearempty (refer to Fuel gaug...

Anti-lock brake system: If the ABS light stays illuminated orcontinues to flash, a malfunction hasbeen detected, have the systemserviced immediately by yourauthorized dealer. Normal braking is still functional unless the brakewarning light also is illuminated. Airbag readiness: If this light fails t...

AdvanceTrac 威 /Traction control (if equipped): Displays when the AdvanceTrac 威 /Traction control is active. If the light remains on, havethe system serviced immediately, refer to the Driving chapter for more information. AdvanceTrac 威 /Traction control off light (if equipped): Illuminates when Advan...

GAUGES Shown in standard measure. Metric similar. 1. Tachometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scalemay damage the engine. Refer to Filling the tank in the Maintenance and Specifications chapter for more info...

TRIP COMPUTER (IF EQUIPPED) Press the end of the lever, locatedon the left side of the steeringwheel to scroll through the displays. To reset the trip odometer andaverage speed, scroll to the requireddisplay and press and hold the endof the multifunction lever. The trip computer includes thefollowin...

Information messages : The message indicator will illuminate when there is a new message stored in the multifunction display. Message Warning Lamp at Instrument Cluster System ABS MALFUNCTIONSERVICE NOW ABS ESP OFF — ABS ESP MALFUNCTIONNEXT SERVICE — ABS BRAKE SYSTEMMALFUNCTIONSTOP SAFELY BRAKE or B...

Message Warning Lamp at Instrument Cluster System ENGINE OILPRESSURE LOWSTOP SAFELY Engine Oil BRAKE FLUIDLEVEL LOWSERVICE NOW BRAKE or Brakes Oil life monitoring system reset To reset the oil service light and clear the oil change message afterservicing use the following procedure: 1. Begin with th...

AUDIO SYSTEMS AM/FM stereo or AM/FM stereo single CD/MP3 (if equipped) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that maytake their focus off the road. Your ...

The auxiliary input jack (AIJ)provides a way to connect yourportable music player to thein-vehicle audio system. This allowsthe audio from a portable musicplayer to be played through thevehicle speakers with high fidelity.To achieve optimal performance,please observe the followinginstructions when a...

GENERAL AUDIO INFORMATION Radio frequencies: AM and FM frequencies are established by the Federal CommunicationsCommission (FCC) and the Canadian Radio and TelecommunicationsCommission (CRTC). Those frequencies are: AM: 530, 540–1700, 1710 kHz FM: 87.9–107.7, 107.9 MHz Radio reception factors: There...

CD units are designed to play commercially pressed 4.75 in(12 cm) audio compact discs only. Due to technicalincompatibility, certain recordable and re-recordable compactdiscs may not function correctly when used in Ford CD players. Do not use any irregular shapedCDs or discs with a scratchprotection...

SYNC 姞 (IF EQUIPPED) Ford ingenuity brings you SYNC 威 – an in-car connectivity system designed with convenience in mind. SYNC literally ‘syncs up’ with your Bluetooth 威 enabled cellular phone and portable media player, creating a comprehensive and easy-to-usesystem offering features such as: • Makin...

Added benefits SYNC 威 even has some benefits which extend beyond your car. You can: • Access on-line support • Chat with other SYNC 威 owners • Search for and download new applications • Check frequently asked questions (FAQs) • Check your phone and other devices’ compatibility • Register and set up ...

• “ Services” (if equipped, U.S. only): Say to access the SYNC Services portal. • “Mobile Apps” (if equipped, U.S. only) : Say to access Mobile Applications (if available). System interaction and feedback The system provides feedback through audible tones, prompts, questionsand spoken confirmations ...

For example, “Say 1 after the tone to call John Doe at home. Say 2after the tone to call Johnny Doe on mobile. Say 3 after the toneto call Jane Doe at home.” Or, “Say 1 after the tone to play JohnDoe, Say 2 after the tone to play Johnny Doe. Helpful Hints • Ensure that the interior of the vehicle is...

Pairing a phone for the first time The first thing you must do to use a phone with the system is towirelessly pair your phone with SYNC. Doing so allows your phone tocommunicate with the hands-free system, thereby enabling you to makeand receive hands-free calls. Note: To scroll through the menus, p...

Phone voice commands Press and when prompted, say, “Phone”. You may then say any of the following: • Call <name> 2 • Call <name> at home 2 • Call <name> on mobile OR cell 2 • Call <name> at work OR Call <name> in office 2 • Call <name> on other 2 • Dial* 2 • Phone...

Answering an incoming call During an incoming call, you will hear an audible ring. You can then: • Answer the call by pressing or PHONE. • Reject the call by pressing and holding or PHONE. • Ignore the call by doing nothing. Phone options during an active call During an active call, you have additio...

Maneuvering the phone menu Below is a graphical representation of how the phone menu lays out inyour system. It will be explained in more detail in this chapter, but thismay help you to better visualize the menu structure. + Denotes submenus with additional menu items PHONE or Phone Redial Call Hist...

Text messaging SYNC allows you to receive, send, download and delete text messages.The system will even read incoming text messages to you so that you donot have to take your eyes off the road. Note: This is a phone dependent feature. Receiving a text message Note: This is a phone dependent feature....

3. Scroll to select from the following options: Send Text Message? : Enables you to send a new text message based on a predefined set of 15 messages. 1. Press OK to select. If the system detects your phone does notsupport this feature, Unsupported will appear in the display and SYNC will return you ...

Modify Phonebook : Allows you to modify the contents of your phone book (i.e. add, delete, download). Press OK to select and scroll to cycle through the followingoptions: • Add Contacts: Press OK to add more contacts from your phone book. ’Push’ the desired contact(s) on your phone. Refer to yourpho...

Scrolling through the menus: Press / on your audio system to scroll through the menu options. Bluetooth Device menu options This menu allows you to add, connect, delete, set a phone as primary, aswell as turn Bluetooth on and off. To access: 1. Press PHONE or to enter the Phone Menu. 2. Scroll until...

Set As Primary Phone? : Select to set a previously paired phone as your primary phone. SYNC will attempt to connect with the primaryphone at every ignition cycle. • Press OK to select and scroll to select the desired phone. Press OK to confirm. Note: When a phone is selected as primary, it will appe...

Accessing and using your SYNC applications and Services(if equipped) In addition to the standard phone and media options which SYNC offers,your system also includes advanced features such as: • 911 Assist™: Can alert 911 in the event of an emergency. • Vehicle Health Report (if equipped, U.S. only):...

To connect to SYNC 威 Traffic, Directions & Information Services using the phone menu: 1. Press or PHONE to enter the Phone Menu. 2. Scroll repeatedly until Services appears in the display. 3. Press OK to confirm and enter the Services menu. The display willindicate the system is connecting. 4. P...

Portable: Your SYNC TDI Services subscription is associated with your Bluetooth enabled cellular phone number, not your VIN (Vehicle Identification Number). Thus, you can use your SYNC TDI Service withany vehicle equipped with Traffic, Directions and Information. Simplypair and connect your phone to...

911 Assist™ (if equipped) For 911 Assist™ to function properly, the vehicle must havebattery power after the crash, the cell phone must be previouslypaired, connected to SYNC 威 , and continue to function properly with the ability to make and maintain a 911 call initiated bySYNC 威 , and the 911 Assis...

Vehicle health report (if equipped, U.S. only) WARNING: Always follow scheduled maintenance instructions, regularly inspect your vehicle, and seek repair for any damage or problem you suspect. Vehicle Health Reports supplements, but cannotreplace normal maintenance and vehicle inspection. Vehicle He...

You can initiate a Vehicle Health Report in the vehicle and view thecomplete report with all information listed above on SyncMyRide.com.You can also choose for SYNC 威 to automatically remind you to run reports at specific mileage intervals. After you’ve registered for theVehicle Health Report servic...

SYNC 姞 AppLink™ (if equipped, U.S. only) SYNC 威 AppLink™ is a software application which allows you to connect to and use applications on your smartphone such as Pandora andStitcher via your SYNC system (provided your phone is compatible withthese features). To see trouble shooting tips, available a...

To access from the phone menu: 1. Press or PHONE to enter the Phone Menu. 2. Scroll repeatedly until Mobile Apps appears in the display. 3. Press OK to enter the menu and view a list of availableapplications (for example, Pandora). 4. Scroll to access the desired application menu (for example,Pandor...

Media voice commands Press and when prompted, say, “USB” . You may then say any of the following: • Play all • Play • Pause • What’s playing? • Play next track • Play previous track • Play song <name> • Search song <name> • Refine song <name> • Similar music • Play next folder 2 • ...

Maneuvering the media menu Below is a graphical representation of how the phone menu lays out inyour system. It will be explained in more detail in this chapter, but thismay help you to better visualize the menu structure. + Denotes submenus with additional menu items Scrolling through the menus: Pr...

Accessing the features of your media menu SYNC’s media menu allows you to select which source you would like tolisten to, how you would like to play your music (by artist, genre, shuffle,repeat, etc.), and also if you need to add, connect or delete devices. To access your media menu: 1. Press AUX an...

Media Settings : Allows you to choose to shuffle or repeat your music in addition to setting your Autoplay settings. Press OK to select and thenscroll to choose from: • Shuffle : Press OK to shuffle available media files in the current playlist. Note: To shuffle all media tracks, you must select Pla...

4. If there are no media files to access, the display will indicate there isno media. If there are media files, you will then have the followingoptions to scroll through and select from: Play all: Allows you to play all indexed media (tracks) from your playingdevice in flat file mode, one at a time ...

Application (if available): You can download new software application (if available) and then load the desired applications onto SYNC throughyour USB port. Refer to the web site for more information. Return : Press OK to exit the current menu. Troubleshooting Your SYNC 威 system is easy to use. Howev...

upgrades, and, if applicable, the Certificate(s) of Authenticity), andthe recipient agrees to the terms of this EULA. If the SOFTWARE isan upgrade, any transfer must include all prior versions of theSOFTWARE. • Termination: Without prejudice to any other rights, FORD MOTOR COMPANY or MS may terminat...

• Additional Software/Services: The SOFTWARE may permit FORD MOTOR COMPANY, third party software and service suppliers, MS,Microsoft Corporation, their affiliates and/or their designated agent toprovide or make available to you SOFTWARE updates, supplements,add-on components, or Internet-based servi...

MOTOR COMPANY instructions provided in the documentation for theDEVICE. Should you have any questions concerning this EULA, or if youdesire to contact FORD MOTOR COMPANY for any other reason, pleaserefer to the address provided in the documentation for the DEVICE. No Liability for Certain Damages: E...

WARNING: Operating certain parts of this system while driving can distract your attention away from the road, and possibly cause an accident or other serious consequences. Do not changesystem settings or enter data non-verbally (using your hands) whiledriving. Stop the vehicle in a safe and legal ma...

MANUAL HEATING AND AIR CONDITIONING SYSTEM Manual system with A/C shown; heater only system similar. 1. : Turn to select the desired fan speed. 2. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control setting: MAX A/C (if...

: Distributes outside air through the windshield defroster and demister vents. Can be used to clear thin ice or fog from thewindshield. The system will automatically provide outside air to reducewindow fogging. To exit select another mode. 3. Temperature: Controls the temperature of the airflow in t...

and put the vehicle’s transmission into the P (Park) gear position(automatic transmission only) to continue to receive cool air from yourA/C system. For maximum cooling performance in MAX A/C mode: 1. Select MAX A/C. 2. Select the coolest temperature setting. 3. Set the fan to the highest speed init...

CABIN AIR FILTER Your cabin air filter is located behind the instrument panel. The cabin airfilter element is designed to reduce the concentration of airborneparticles such as dust, spores and pollen in the air being supplied to theinterior of the vehicle. The presence of a particulate filter elemen...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the low beam headlamps on. High beams Pull the lever fully past the detentto activate. Pull the lever fully againto deactivate. Flash-to-pass Pull the lever toward you s...

Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the ignition must be in the on position and • the headlamp control is in the off or parking lamp position. WARNING: Always remember to turn on your headlamps at dusk or during inclement weather. Th...

• (1) 8 feet (2.4 meters) • (2) Center height of lamp toground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height of theheadlamp bulb center from theground and mark an 8 foot(2.4 meter) horizontal reference lineon the vertical wall or screen at thisheight. 3. Turn on th...

TURN SIGNAL CONTROL • Push down to activate the leftturn signal. • Push up to activate the right turnsignal. When changing lanes, the turn signal indicator can be programmed toflash either one or three times when the stalk is tapped. See Multifunction display in the Instrument cluster section for mo...

BULB REPLACEMENT Lamp assembly condensation Exterior lamps are vented to accommodate normal changes in pressure.Condensation can be a natural by-product of this design. When moist airenters the lamp assembly through the vents, there is a possibility thatcondensation can occur when the temperature is...

Function Number of bulbs Trade number 5-door rear lamp(stop/reverse) 2 3157K 5-door rear lamp (turn) 1 3157A (amber) License plate lamp 1 W5W * 5–door high-mountedbrake lamp 1 LED * 4–door high-mountedbrake lamp 5 W5W Interior lamp 1 W6W Reading lamp 1 W5W Luggage compartmentlamp 1 W5W To replace al...

Replacing the rear stop lamp (5-door) 1. Turn the bulb holdercounterclockwise and remove it. 2. Remove the bulb from the holder. 3. Reverse the procedure to install the new bulb. Replacing the reverse signal rear lamp (5-door) 1. Turn the bulb holdercounterclockwise and remove it. Lights 116 2012 Fi...

WINDSHIELD WIPERS Move the lever down for a singlewipe. For intermittent operation, move control up one position andadjust the rotary control to thedesired speed. For normal operation, move control up two positions and up three positions for high-speed wiping. Windshield washer To activate the winds...

To prevent the fuse from being blown, do not use the power point(s)over the vehicle capacity of 12V DC/180W. If the power point or cigarlighter socket is not working, a fuse may have blown. Refer to Fuses and relays in the Roadside Emergencies chapter for information on checking and replacing fuses....

EXTERIOR MIRRORS Power side view mirrors WARNING: Do not adjust the mirror while the vehicle is in motion. To adjust your mirrors: 1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror. 2. Move the control in the directionyou wish t...

Signal indicator mirrors (if equipped) When the turn signal is activated,the outer portion of the appropriatemirror housing will blink. This provides an additional warningto other drivers that your vehicle isabout to turn. SPEED CONTROL (IF EQUIPPED) With speed control set, you can maintain a set sp...

KEYS Integrated keyhead transmitters (IKTs) (if equipped) Your vehicle may be equipped withtwo integrated keyhead transmitters(IKTs). The key blade is used tostart the vehicle and unlock/lock thedriver’s door from outside thevehicle. The transmitter portionfunctions as the remote entrytransmitter. Y...

Central locking/unlocking To centrally lock/unlock all doors (from the driver’s side only) using thekey from the outside when they are closed: • Turn the key counterclockwise to lock all doors. The turn signal lampswill flash twice. • Turn the key clockwise once to unlock the driver’s door or twice ...

Autounlock (if equipped) If the doors have been autolocked, the doors will autounlock only when: • the ignition is on, • all doors are closed, • the vehicle has been in motion at a speed greater than 12 mph(20 km/h) for more than two seconds, • the vehicle comes to a stop, • the ignition is turned o...

REMOTE ENTRY SYSTEM (IF EQUIPPED) FCC ID: LXP-RX4318 IC: 2298A-RX4318 The integrated keyhead transmitters (IKTs) and intelligent access keys(IA key) comply with part 15 of the FCC rules and with RSS-210 ofIndustry Canada. Operation is subject to the following two conditions:(1) This device may not c...

Activating intelligent access atthe front doors: If your IA key is within 3 feet (1 meter) of thedriver’s door or passenger frontdoor, you can activate yourintelligent access system by pressingthe lock button. To lock/unlock the doors, press thelock button on the handle. Pressing the driver’s door l...

2. Release the retaining clips with aflat object and separate the twohalves of the transmitter. 3. Carefully pry out the battery witha flat object. Be careful not to touchthe battery contacts or the printedcircuit board with the flat object. Note: Please refer to local regulations when disposing oft...

3. Twist a flat object in the positionshown to separate the two halves ofthe transmitter. 4. Carefully insert a flat object inthe position show to open thetransmitter. 5. Carefully pry out the battery with a flat object. Note: Please refer to local regulations when disposing of transmitter batteries...

Please read and understand the entire procedure before you begin. Reprogramming remote entry transmitters 1. Insert the first programmed key into the ignition and turn the keyfrom off to run (maintain the key in run for approximately 3 seconds). 2. Turn the first key to off and remove it from the ig...

Replacement keys If your keys are lost or stolen and you don’t have an extra coded key,you will need to have your vehicle towed to an authorized dealer. Thekey codes need to be erased from your vehicle and new coded keys willneed to be programmed.Replacing coded keys can be very costly. Store an ext...

Front seat head restraints Rear seat outboard headrestraints Rear seat center head restraints The head restraints consist of: A. An energy absorbing head restraint B. Two steel stems C. Guide sleeve adjust and release button D. Guide sleeve unlock and remove button E. Fold button D B A B C Seating a...

Note: Adjust the seatback to an upright driving position before adjusting any head restraint. Adjust the head restraint so that the top of it is levelwith the top of your head and as far forward as possible, remainingcomfortable. For occupants of extremely tall stature, adjust the headrestraint to i...

• Recline adjustment Lift the control to adjust the angleof the seatback. WARNING: Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. Using the armrest (if equipped) Move the armrest up or down. Youca...

The adjustable outboard headrestraints consist of : • a trimmed energy absorbing foamand structure (1), • two steel stems (2), • a guide sleeve adjust releasebutton (3), • and a guide sleeve unlock/removebutton (4). Center seat position Your vehicle is equipped with a second row center head restrain...

Driver and passenger dual-stage airbag supplemental restraints The dual-stage airbags offer the capability to tailor the level of airbaginflation energy. A lower, less forceful energy level is provided for morecommon, moderate-severity impacts. A higher energy level is used forthe most severe impact...

The front passenger sensing system can automatically turn off thepassenger front airbag. The system is designed to help protect small(child size) occupants from airbag deployments when they areimproperly seated or restrained in the front passenger seat contrary toproper child-seating or restraint us...

Determining if the Personal Safety System is operational The Personal Safety System uses a warning light in the instrumentcluster or a backup tone to indicate the condition of the system. Refer tothe Warning lights and chimes section in the Instrument Cluster chapter. Routine maintenance of the Pers...

Combination lap and shoulder belts The front outboard and rear safety restraints in the vehicle arecombination lap and shoulder belts. 1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until you hear a snap and feelit latch. Make sure the t...

Pregnant women should alwayswear their safety belt. The lap beltportion of a combination lap andshoulder belt should be positionedlow across the hips below the bellyand worn as tight as comfort willallow. The shoulder belt should bepositioned to cross the middle ofthe shoulder and the center of thec...

How to use the automatic locking mode 1. Buckle the combination lap andshoulder belt. 2. Grasp the shoulder portion andpull downward until the entire beltis pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the auto...

Safety belt extension assembly If the safety belt is too short when fully extended, a safety belt extensionassembly can be obtained from an authorized dealer. Use only extensions manufactured by the same supplier as the safetybelt. Manufacturer identification is located at the end of the webbing ont...

Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and achime sounds to remind the occupants to fasten their safety belts. Conditions of operation If... Then... The driver’s safety belt is notbuckled before the ignitionswitch is turned t...

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... “Crashes are rare events” 36700 crashes occur every day. The more we drive, the more we areexposed to “rare” events, even forgood drivers. 1 in 4 of us will be ser...

Reasons given... Consider... “I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate in rear andside crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likelyto DIE. Safety be...

Children and airbags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating position. Failure to followthese instructions may increase therisk of injury in a collision. WARNING: Airb...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

• a readiness light and tone • and the electrical wiring which connects the components • Side curtain airbag system. Refer to Side curtain airbag system later in this chapter. • Front passenger sensing system. Refer to Front passenger sensing system later in this chapter. • “Passenger airbag off” or...

WARNING: To reduce the risk of possible serious injury: Do not stow objects in seat back map pocket (if equipped) or hang objects off seat back if a child is in the front passenger seat.Do not place objects underneath the front passenger seat or betweenthe seat and the center console (if equipped).C...

The airbag SRS is designed to activate when the vehicle sustains lateraldeceleration sufficient to cause the sensors to close an electrical circuitthat initiates airbag inflation. The fact that the airbags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, i...

Side-curtain airbag system WARNING: Do not place objects or mount equipment on or near the headliner at thesiderail that may come intocontact with a deploying side aircurtain. Failure to follow theseinstructions may increase the riskof personal injury in the event of acollision. WARNING: Do not plac...

The side air curtains are mounted to the sheet metal above the first andsecond row seats. In certain lateral collisions, the air curtain andseat-mounted side airbag on the side affected by the collision will beinflated, except that the passenger sensing system will deactivate thepassenger seat-mount...

Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Refer to Warning lights and chimes in the Instrument Cluster chapter. Routine maintenance of the side airbag is not required. A difficulty with the syst...

SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag supplemental restraint system (SRS) in this chapter for special instructions about using airbags. Important child restraint precautions WARNING: Always make ...

Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommendedrestraint type Infantsortoddlers Children weighing 40 lb (18 kg) or less(generally age four or younger) Use a child safetyseat (sometimescalled an infantcarrier, convertibleseat, or toddlerseat). Smallch...

Recommendations for attaching child safety restraints for children RestraintType Child Weight Use any attachment method as indicated below by “X” LATCH(loweranchorsandtoptetheranchor) LATCH(loweranchorsonly) Safetybeltandtoptetheranchor Safetybelt andLATCH(loweranchorsand toptetheranchor) Safetybelt...

WARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision, which may result in serious injury ordeath. WARNING: Never use pillows, books, or towels to boost a child. They can slide around and increase ...

Follow all the safety restraint and airbag precautions that apply to adultpassengers in your vehicle. If the child is the proper height, age, and weight (as specified by yourchild safety seat or booster manufacturer), fits the restraint and can berestrained properly, then restrain the child in the c...

Perform the following steps when installing the child seat withcombination lap/shoulder belts: Note: Although the child seat illustrated is a forward facing child seat, the steps are the same for installing a rear facing child seat. 1. Position the child safety seat in aseat with a combination lap a...

4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear a snap and feel the latchengage. Make sure the tongue islatched securely by pulling on it. 5. To put the retractor in theautomatic locking mode, grasp...

Use of inboard lower anchors from the outboard seating positions(center seating use) The lower anchors at the center of the second row rear seat are spaced390 mm (15 inches) apart. The standardized spacing for LATCH loweranchors is 280 mm (11 inches) center to center. A child seat with rigidLATCH at...

Attaching child safety seats with tether straps Many forward-facing child safety seats include a tether strap whichextends from the back of the child safety seat and hooks to an anchoringpoint called the top tether anchor. Tether straps are available as anaccessory for many older safety seats. Conta...

Child booster seats The belt-positioning booster (booster seat) is used to improve the fit ofthe vehicle safety belt. Children outgrow a typical child seat (e.g.,convertible or toddler seat) when they weigh about 40 lb (18 kg) and arearound four (4) years of age. Consult your child safety seat owner...

• High back booster seats If, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boosterseat would be a better choice. Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the...

Child restraint and safety belt maintenance Inspect the vehicle safety belts and child safety seat systems periodicallyto make sure they work properly and are not damaged. Inspect thevehicle and child seat safety belts to make sure there are no nicks, tearsor cuts. Replace if necessary. All vehicle ...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING Tire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperature A These Tire Quality G...

WARNING: Under-inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or “blowout”, with unexpected loss of vehicle control and increasedrisk of injury. Under-inflation increases sidewall flexing and rollingresistance, resulting in heat buildup a...

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, ...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

Safety Practices WARNING: If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to fiveseconds. WARNING: Do not spin the wheels at over 35 mph (56 km/h). The tires may fa...

Tire and Wheel Alignment A bad jolt from hitting a curb or pothole can cause the front end of yourvehicle to become misaligned or cause damage to your tires. If yourvehicle seems to pull to one side when you’re driving, the wheels may beout of alignment. Have an authorized dealer check the wheel ali...

7. H: Indicates the tire’s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods oftime under a standard condition of load and inflation pressure. The tireson your vehicle may operate at different conditions for load and inflationpressure. The...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below. Note: Tire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the Tire a...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Grades donot apply ...

following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that may cause undesired operation. WARNING: The tire pressure monitoring system is NOT a substitute for manually checking tire pressure. The ...

To restore the full functionality of the tire pressure monitoring system,have the damaged road wheel/tire repaired and remounted on yourvehicle. For additional information, refer to Changing tires with a TPMS in this section. When you believe your system is not operating properly The main function o...

Low tirepressurewarning light Possible cause Customer action required Flashingwarning light Spare tire in use Repair the damaged road wheel/tire and reinstall it on the vehicle torestore system functionality. For adescription on how the systemfunctions, refer to When your temporary spare tire is ins...

Vehicle Curb Weight – is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarketequipment. Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. Tires, Wheels and Loading 226 2012 Fiesta (fie) Owners Guide, 3rd PrintingUSA (fus)

GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance...

WARNING: Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tireswith a higher limit than the original tires do not increase the GVWRand GAWR limitations. WARNING: Exceeding any vehicle ...

• A final example for your vehicle with 1400 lb. (635 kg) of cargo andluggage capacity. You and one of your friends decide to pick upcement from the local home improvement store to finish that patioyou have been planning for the past 2 years. Measuring the inside ofthe vehicle with the rear seat fol...

Follow these guidelines if you have a need for recreational (RV) towing.An example of recreational towing would be towing your vehicle behinda motor home. These guidelines are designed to ensure that yourtransmission is not damaged. Before you tow your vehicle, follow these directions for your speci...

STARTING Positions of the ignition If your vehicle is equipped with a push button start system, refer to Push button start system in this section for ignition modes. 1. 0 (off) — locks the steeringwheel, automatic transmissiongearshift lever and allows keyremoval. This position also shuts theengine ...

Starting the engine Note: If your vehicle is equipped with a push button start system, refer to Push button start system in this section for starting. 1. Turn the key to II (on) withoutturning the key to III (start). 2. Turn the key to III (start), thenrelease the key as soon as theengine begins cra...

2. On — press the START/STOP button without applying the brake pedal(automatic transmission) or clutch pedal (manual transmission). This willpower your vehicle’s electrical system and the warning lights in theinstrument cluster will illuminate, but the engine will remain off. 3. Start — press the ST...

Fast restart feature: The fast restart feature allows you to re-start your vehicle within 10 seconds of switching the vehicle off, if a valid IA key isnot present when the vehicle is switched off. You can re-start the vehicle(by applying the brake/clutch pedal and pressing the START/STOP button)for ...

• Be sure that areas where the vehicle is parked are clean and clear ofall combustibles such as petroleum products, dust, rags, paper andsimilar items. • Be sure that the engine block heater, heater cord and extension cordare solidly connected. A poor connection can cause the cord tobecome very hot ...

Brake over accelerator This vehicle is equipped with a brake over accelerator feature. In theevent the accelerator pedal becomes stuck or entrapped, applying steadyand firm pressure to the brake pedal will both slow the vehicle andreduce engine power. If you experience this condition, apply the brak...

Anti-lock braking, and ESC are not affected by this condition and willcontinue to function during the cool-down period. Electronic stability control (ESC) Electronic stability control (ESC) may enhance your vehicle’s directionalstability during adverse maneuvers, for example when cornering severelyo...

AdvanceTrac 威 Features TCS switchinmulti-functiondisplay Stability control light Stability control off light ESC TCS Default atstart-up Illuminated during bulb check Illuminated during bulb check Enabled Enabled De-select TCS Not illuminated Illuminated solid Enabled Disabled Select TCSagain afterde...

may display in the multifunction display. Refer to the Message center in the Instrument Cluster chapter for more information. WARNING: The EPS has diagnostics checks that continuously monitor the EPS to ensure proper operation of the electronic system. When an electronic error is detected, the messa...

• Allows the transmission to select gears that will provide the desiredengine braking based on the vehicle inputs mentioned above. This willincrease engine RPM during engine braking. Overdrive cancel with grade assist is designed to provide optimal gearselection in hilly terrain or mountainous areas...

MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Using the clutch Manual transmission vehicles have a starter interlock that preventscranking the engine unless the clutch pedal is fully pressed. To start the vehicle: 1. Make sure the parking brake is fully set. 2. Press the clutch pedal to thefloor, then...

HILL START ASSIST (HSA) SYSTEM (IF EQUIPPED) The hill start assist (HSA) system makes it easier to pull away when thevehicle is on a slope without the need to use the parking brake. WhenHSA is active, the vehicle will remain stationary on the slope for two tothree seconds after you release the brake...

3. When you remove your foot from the brake pedal, the vehicle willremain on the slope without rolling away for approximately two to threeseconds. This hold time will automatically be extended if you are in theprocess of driving off. 4. Drive off in the normal manner. The brakes will be releasedauto...

BLIND SPOT MIRRORS Blind spot mirrors have an integrated convex spotter mirror built intothe upper outboard corner of the outside mirrors. They are designed toassist the driver by increasing visibility along the side of the vehicle. Formore information on your side view mirrors, refer to Exterior mi...

DRIVING THROUGH WATER If driving through deep or standingwater is unavoidable, proceed veryslowly. Never drive through waterthat is higher than the bottom ofthe wheel rims (for cars) or thebottom of the hubs (for trucks). When driving through water, traction or brake capability may be limited.Also, ...

ROADSIDE ASSISTANCE Vehicles sold in the U.S. : Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24-hours,...

Vehicles sold in the U.S. : Using roadside assistance Complete the roadside assistance identification card and place it in yourwallet for quick reference. This card is found in the owner’s informationportfolio in the glove compartment. U.S. Ford vehicle customers who require Roadside Assistance, cal...

FUEL PUMP SHUT-OFF In the event of a moderate to severe collision, this vehicle is equippedwith a fuel pump shut-off feature that stops the flow of fuel to theengine. Not every impact will cause a shut-off. Should your vehicle shut off after a collision due to this feature, you mayrestart your vehic...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Protected circuits F1 15A Ignition switch, Keyless entryignition relay, Keyless entryaccessory relay F2 10A Electronic mirror, A/C clutch,Engine compartment fuse panel F3 7.5A Instrument cluster F4 7.5A Passenger airbag deactivation...

CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily.Instead, gradually decrease your speed. Hold the steering wheel firmlyand slowly move to a safe place on the side of the road. Note: The tire pressure monitoring system (TPMS) indicator light will illuminate when...

WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the specified torque within 100 miles (160 km)after any wheel disturbance (tire rotation, changing a flat tire, wheelremoval, etc.). Bolt size Wheel lug nut torque* ft-lb N • m M12 x 1.5 100 135 * Torque specifications are for nut and bol...

Connecting the jumper cables Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery. 1. Connect the positive (+) jumpercable to the positive (+) terminal ofthe discharged battery. 2. Connect the other end of thepositive (+) cable to the positive(+)...

Jump Starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift anddollies or flatbed equipment. Do not tow w...

Emergency towing In case of a roadside emergency with a disabled vehicle (without accessto wheel dollies, car hauling trailer, or flatbed transport vehicle) yourvehicle (regardless of transmission powertrain configuration) can be flattowed (all wheels on the ground) under the following conditions: •...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizeddealer. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfaction. Plea...

In Canada: Mailing address Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Additional assistance If you have questions or concerns, or are unsatisfied with the service youare receiving, follow ...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft 威 Detail Wash (ZC-3-A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can ...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with ...

PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your authorized dealer. • For routine cleaning, use Motorcraft 威 Detail Wash (ZC-3-A). • If tar or grease spots are present, use Motorcraft 威 Bug and Tar Remover (ZC-42). WINDOWS ...

INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENS Clean the instrument panel, interior trim areas and cluster lens with aclean, damp, white cotton cloth, then use a clean and dry white cottoncloth to dry these areas. • Avoid cleaners or polishes that increase the gloss of the upper portionof the instr...

INTERIOR For fabric, carpets, cloth seats, safety belts and seats equipped with sideairbags: • Remove dust and loose dirt with a vacuum cleaner. • Remove light stains and soil with Motorcraft 威 Professional Strength Carpet & Upholstery Cleaner (ZC-54). • If grease or tar is present on the materi...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide to find out wh...

WARNING: To reduce the risk of vehicle damage and/or personal burn injuries, do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under theinstrument panel. 2. Raise the hoo...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 1. Engine coolant reservoir 2. Engine oil filler cap 3. Battery 4. Brake/Clutch fluid reservoir 5. Power distribution box 6. Windshield washer fluid reservoir 7. Air filter assembly 8. Engine oil dipstick 8 7 6 5 1 2 3 4 Maintenance and Specifications...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specifications. Do not use anyspecial washer fluid such aswindshield water repellent type fluidor bug wash. They may causesque...

To replace the wiper blades: 1. Pull the wiper arm away from thewindshield. 2. Press the locking button (1). 3. Remove the wiper blade (2). Note: Make sure the wiper blade locks into place. ENGINE OIL Checking the engine oil Refer to the scheduled maintenance information for the appropriate interval...

Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler capand use a funnel to pour the engine oil...

Do not use supplemental engine oil additives, cleaners or other enginetreatments. They are unnecessary and could lead to engine damage thatis not covered by Ford warranty. Change your engine oil and filter according to the appropriate schedulelisted in the scheduled maintenance information. Ford pro...

• If you do not allow the engine to relearn its idle trim, the idlequality of your vehicle may be adversely affected until the idletrim is eventually relearned. When the battery is disconnected or a new battery installed, theautomatic transmission must relearn its adaptive strategy. As a result ofth...

• Improved boiling protection. • Protection against rust and other forms of corrosion. • Proper function of calibrated gauges. When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the FULL COLD level, or within theCOLD FILL or MIN / MAX ran...

WARNING: Do not put engine coolant in the windshield washer fluid container. If sprayed on the windshield, engine coolant could make it difficult to see through the windshield. • DO NOT MIX different colors or types of coolant in your vehicle. Make sure the correct coolant is used. Mixing of engine ...

Add the proper mixture of coolant and water to the cooling system byfollowing these steps: 1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the coolantpressure relief cap on the coolant reservoir (a translucent plastic bottle).Slowly tur...

Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Maintenance product specifications and capacities in this chapter. Fill your engine coolant reservoir as outlined previously in the Adding engine coolant section. Severe climates If you drive in extrem...

Refueling WARNING: Fuel vapor burns violently and a fuel fire can cause severe injuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; ...

Note: A fuel spillage concern may occur if overfilling the fuel tank. Do not overfill the tank to the point that the fuel is able to bypass the fuelfiller nozzle. If the check fuel fill inlet lamp comes on, the fuel fill inlet may not haveproperly closed. The inlet may have stuck open or debris may ...

Do not be concerned if your engine sometimes knocks lightly. However, ifit knocks heavily under most driving conditions while you are using fuelwith the recommended octane rating, see your authorized dealer toprevent any engine damage. Fuel quality If you are experiencing starting, rough idle or hes...

Refilling with a portable fuel container With the Easy Fuel 威 “no cap” fuel system, use the following directions when filling from a portable fuel container: WARNING: Do not insert the nozzle of portable fuel containers or aftermarket funnels into the Easy Fuel 威 system. This could damage the fuel s...

Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers). 2. Each time you fill the tank, record the amount of fuel added (ingallons or liters). 3. After at least three to five tank fill-ups, fill the fuel tank and recordthe current od...

EMISSION CONTROL SYSTEM WARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. WARNING: Exhaust leaks may result in entry of harmful and potentially lethal fumes into th...

BRAKE/CLUTCH FLUID Brake and clutch (if equipped) systems are supplied from the samereservoir. The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced. Fluid levels between the MIN andMAX lines are within the normaloperating range; there is no need toa...

Do not use supplemental transmission fluid additives, treatments orcleaning agents. The use of these materials may affect transmissionoperation and result in damage to internal transmission components. Checking 5-speed manual transmission fluid (if equipped) The manual transmission does not have a t...

Changing the air filter element 1. Remove the four screws thatsecure the air filter housing cover. 2. Carefully separate the two halvesof the air filter housing. 3. Remove the air filter elementfrom the air filter housing. 4. Wipe the air filter housing andcover clean to remove any dirt ordebris and...

MOTORCRAFT 姞 PART NUMBERS Component 1.6L engine Air filter element FA-1904 Oil filter FL-910S 1 Battery BXT-96R-500 Spark plugs 2 Cabin air filter FP69 Windshield wiper blade WW-2601-PF (driver side)WW-1601-PF (passenger side) 1 Only use the specified replacement oil filter. The use of a non-specifi...

TRANSMISSION CODE DESIGNATIONS You can find a transmission code onthe Safety Compliance CertificationLabel. The following table tells youwhich transmission each coderepresents. Description Code Five-speed manual transmission C Six-speed automatic transmission A Maintenance and Specifications 330 201...

FORD CUSTOM ACCESSORIES FOR YOUR VEHICLE A wide selection of Ford Custom Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement the ...

Peace of mind • Keyless entry keypad • Seat covers* • Remote start • Car covers* • Wheel locks • Bumper mounted parking sensors* *Ford Licensed Accessories (FLA) are warranted by the accessorymanufacturer’s warranty. Ford Licensed Accessories are fully designedand developed by the accessory manufact...

FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY) More than 32 million Ford and Lincoln owners have discovered thepowerful protection of Ford ESP. It is the only extended service planbacked by Ford Motor Company, and provides “peace of mind”protection beyond the New Vehicle Limited Warranty coverage. Up t...

FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY) You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is the only service contractbacked by Ford Motor Company of Canada, Limited. Depending on theplan you purchase, Ford ESP provides benefits such as: • R...

GENERAL MAINTENANCE INFORMATION Why maintain your vehicle? Carefully following this schedule helps protect against major repairexpenses resulting from neglect or inadequate maintenance and may alsohelp to increase the value of your vehicle when you sell or trade it. It is your responsibility to see ...

Genuine Ford parts and service When planning your maintenance services, consider your dealership forall your vehicle’s needs. There are a lot of reasons why visiting your dealership for all yourservice needs is a great way to help keep your vehicle running great. Convenience Many dealerships have ex...

NORMAL SCHEDULED MAINTENANCE AND LOG Your vehicle is equipped with a oil minder system that indicates whenthe engine oil should be changed under normal operating conditions.This means you won’t have to remember to change the oil on amileage-based schedule; the vehicle lets you know when an oil chang...

Maintenance Schedule Log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ...

SPECIAL OPERATING CONDITIONS If you operate your vehicle primarily in any of the following conditions, you need to perform additional maintenance as indicated. If you occasionally operate your vehicle under any of these conditions, it is not necessary to perform the additional maintenance. For speci...

Operating in dusty or sandy conditions such as unpaved or dusty roads Inspect frequently,service as required Replace cabin air filter (if equipped) Replace engine air filter (except Fusion Hybridand MKZ Hybrid)* Every 5,000 miles(8,000 km) Inspect the wheels and related components forabnormal noise,...

Special Operating Condition Log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D A...

EXCEPTIONS There are several exceptions to the Normal Schedule. They are listedbelow: Normal vehicle axle maintenance: Rear axles and power take-off (PTO) units with synthetic fluid and light-duty trucks equipped withFord-design axles are lubricated for life; do not check or change fluidunless a lea...

Edge/MKX AWD only – vehicles operating off-road in sand during high ambient temperatures must replace the AWD PTU (All-wheel drivePower Transfer Unit) lube every 20,000 miles (32,000 km). Engine air filter & cabin air filter replacement: Engine air filter and cabin air filter life is dependent o...

911 Assist™ ................................69 A Accessing call history/phonebook during active call ...............52 Accessing your media menufeatures ........................................80 Accessing your phone menufeatures ........................................56 Active call menu options .....

coolant .....................................302idle speed control ...................300lubrication specifications .......325refill capacities ........................325service points ..................296–297 Engine block heater .................239 Engine fan .................................296...

Vehicle Identification Number(VIN) ..........................................329 Vehicle loading ..........................224 Ventilating your vehicle ...........238 Voice commands in mediamode ............................................77 Voice commands in phonemode .................................