Ford 2012 F-550 v.3- User Manual

Notice to owners of pickup trucks and utility type vehicles WARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles. Before you drive your vehicle, please read this Owner’s Guide carefully.Your vehicle is not a passenger car. As with other vehicles of this ty...

Using your vehicle as a stationary power source (PTO) Refer to the Driving chapter for more information and guidelines for operating a vehicle equipped with an aftermarket power take-off system. DATA RECORDING Service Data Recording Service data recorders in your vehicle are capable of collecting an...

Additionally, when you connect to Traffic, Directions andInformation (if equipped, U.S. only), the service uses GPStechnology and advanced vehicle sensors to collect the vehicle’scurrent location, travel direction, and speed (“vehicle travelinformation”), only to help provide you with the directions...

Mobile communication equipment includes, but is not limited to, cellularphones, pagers, portable email devices, text messaging devices andportable two-way radios. WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that you use extre...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Base instrument cluster with standard measure shown; metricsimilar Optional instrument cluster with standard measure shown; metricsimilar Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light...

Standard message center Note: Some warning lights are reconfigurable telltale (RTT)indicator lights and will illuminate inthe message center. These lightsfunction the same as the otherwarning lights. Optional message center Note: Some warning lights are reconfigurable telltale (RTT)indicator lights ...

WARNING: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possiblycausing a fire. Check fuel cap: Displays when the fuel cap may not be properlyinstalled. Continued driving wit...

WARNING: Driving a vehicle with the brake system warning light on is dangerous. A significant decrease in braking performance may occur. It will take you longer to stop the vehicle.Have the vehicle checked by your authorized dealer. Driving extendeddistances with the parking brake engaged can cause ...

Transmission Tow/Haul Feature(if equipped): Displays when the Tow/Haul feature has beenactivated. Refer to the Driving chapter for transmission function and operation. If the light flashessteadily, have the system serviced immediately, damage to thetransmission could occur. AdvanceTrac 威 /Traction c...

Electronic locking differential(RTT and static) (if equipped): Displays when using the electroniclocking differential. Speed control (if equipped): The speed control system indicator lightchanges color to indicate what modethe system is in: • On (amber light): Illuminates when the speed control syst...

Key-in-ignition warning chime: Sounds when the key is left in the ignition in the off or accessory position and the driver’s door is opened. Headlamps on warning chime: Sounds when the headlamps or parking lamps are on, the ignition is off (the key is not in the ignition) and thedriver’s door is ope...

TIMER Timer displays the trip elapsed drive time. To operate, do the following: 1. Press and release RESET in order to start the timer. 2. Press and release RESET to pause the timer. 3. Press and hold RESET until the timer resets. TBC GAIN (if equipped) Displays the level of trailer brake gain or if...

AUTOUNLOCK This feature automatically unlocks all vehicle doors when the driver’sdoor is opened within 10 minutes of the ignition being turned off. Press RESET to turn it off or on. COURTESY WIPE One extra wipe will occur a few seconds after washing the front windowto clear any excess washer fluid r...

TO EXIT 4X4 LOW SHIFT TO N (if equipped) — Displayed when 2WD is selected while the vehicle has been stopped in 4X4 LOW. Formore information, refer to Four-wheel drive (4WD) operation in the Driving chapter. TO EXIT 4X4 LOW APPLY BRAKE (if equipped) — Displayed when 2WD is selected from 4X4 LOW mode...

SPEED LIMITED XXMPH IN XXXMI EXHAUST FLUID SYSTEMFAULT (diesel engine only) — Displayed when the SCR system detects a fault. The vehicle’s top speed will become limited in thedisplayed distance and count down from this point. Refer to your dieselsupplement for more information. Contact your authoriz...

LOW FUEL PRESSURE SEE MANUAL (diesel engine only) — If this message appears during a cold start or during cold operation 32°F(0°C) up to 10 minutes after the initial cold start; monitor the messagecenter and if it disappears and does not re-appear after the engine hasfully warmed up, the low fuel pr...

Press the up/down buttons to moveup/down through the messagecenter choices. Press the left/right buttons to moveleft/right through the messagecenter choices. Press the OK button to selecthighlighted options and confirmchoices/messages. Main menu From the main menu screen you can choose the following...

Trailer* Change ActiveTrailer When this is highlighted, press the right arrow key tochange the currently selected trailer. Use the up anddown arrows to select a trailer and press the OKbutton to choose the highlighted trailer. Adding a new trailer– Use the up/down arrows tohighlight “New Trailer” fr...

Settings In this mode, you can configure different driver setting choices. Pressthe right arrow key (when in the Settings menu) to reach the DriverAssist menu: Driver Assist* Rear Park Aid On/Off Rear ViewCamera Camera Delay Trailer BrakeMode Electric or Elect. Over Hydraulic Trailer SwayControl On/...

System Reset Hold OK to Reset System to Factory Default Information In this mode, you can view different vehicle system information andperform a system check. When “Press OK for info” is displayed, pressing OK will give youinformation on the currently selected/displayed options. Information isonly a...

EXHAUST FLUID RANGE XXX MI (diesel engine only) — Displays the distance you can travel before depleting the remaining diesel exhaustfluid. Refer to your diesel supplement for more information. IN XX MILES, SPEED LIMITED TO XX MPH EXHAUST FLUIDEMPTY (diesel engine only) — Displayed when the diesel ex...

SPEED LIMITED TO 50 MPH EXHAUST FLUID SYSTEM FAULT(diesel engine only) — Displayed when the SCR system detects a fault. The vehicle’s top speed is limited. Refer to your diesel supplementfor more information. Contact your authorized dealer as soon as possible. ENGINE IDLED SOON EXHAUST FLUID SYSTEM ...

LOCKING DIFFERENTIAL DISENGAGED (if equipped) — Displayed when the electronic locking differential is disengaged. See Electronic locking differential in the Driving chapter for more information. FOR HILL DESCENT REDUCE SPEED (if equipped) — Displayed when the vehicle speed requirement for off-road m...

AUDIO SYSTEMS AM/FM stereo system (if equipped) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that maytake their focus off the road. Your primary responsibility ...

7. SHUFFLE: In CD/MP3 mode, press SHUFFLE to engage shufflemode. SHUFFLE ON will appear inthe display. If you wish to engage shuffle mode right away, press SEEKto begin random play. Otherwise, random play will begin when thecurrent track is finished playing. CD SHUF will appear in the display. Todis...

13. TEXT/SCAN: In radio and CD/MP3 mode, press and hold for a brief sampling of radio stations orCD tracks. Press again to stop. In CD/MP3 mode, press and release to display track title, artist name, and disc title. In satellite radio mode (if equipped), press and release to enter TEXT MODE and disp...

18. CD slot: Insert a CD label side up in the CD slot. Auxiliary input jack (if equipped) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that maytake their focus ...

USB port (if equipped) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take theirfocus off the road. Your primary responsibility is the safe operation ofthe vehicle....

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommended that homemadeCDs be identified withpermanent felt tip marker ratherthan adhesive labels. Ballpoint pens may damage CDs. Pleasecontact your authori...

Sample MP3 structure If you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variousfiles may be present, (files withextensions other than mp3), onlyfiles with the .mp3 extension will beplayed. Other files will be ignoredby the syst...

Radio Display Condition Action Required NO TEXT Category information not available. Category information not available at this time on this channel. The system is working properly. NO SIGNAL Loss of signal from the SIRIUS 威 satellite or SIRIUS 威 tower to the vehicle antenna. You are in a location th...

SINGLE ZONE CLIMATE CONTROL 1. Defrost: Distributes outside air through the windshield defroster vents and de-mister vents. Can be used to clear the windshield of fogand thin ice. The system will automatically provide outside air to reducewindow fogging. Press this button again to return to the prev...

• Do not put objects under the front seats that will interfere with theairflow to the back seats. • Remove any snow, ice or leaves from the air intake area at the base ofthe windshield. • To improve the A/C cool down, drive with the windows slightly openfor 2-3 minutes after start up or until the ve...

REAR WINDOW DEFROSTER (IF EQUIPPED) R The rear defroster control is located on the climate control panel andworks to defrost your rear window from fog and thin ice. If equipped, italso operates the heated mirror to remove snow and thin ice from theside mirrors. Ensure that the ignition on. Press to ...

For moderate weather conditions: • The interior cabin will be heated, cooled or off, based upon theprevious operating state (last ignition-on cycle). • Rear defrost/heated mirrors (if equipped) will be deactivated. Automatic climate control For hot weather conditions: • The interior cabin will be se...

HEADLAMP CONTROL Rotate the headlamp controlclockwise to the first position to turn on the parking lamps. Rotate clockwise to the secondposition to also turn on the headlamps. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights no...

2. Turn the headlamp control to off. 3. Turn the ignition switch to on and then back to off. 4. Turn the headlamp control to the autolamp position. The headlampswill turn on. 5. Wait the desired amount of time for the exit delay you want (up tothree minutes), then turn the headlamps off. Fog lamp co...

Vertical aim adjustment The headlamps on your vehicle can only be vertically adjusted. Yourvehicle does not require horizontal aim adjustments. To adjust the headlamps: 1. Park the vehicle directly in front of a wall or screen on a level surface,approximately 25 feet (7.6 meters) away. • (1) 8 feet ...

TURN SIGNAL CONTROL The turn signal lever does not mechanically lock in the upward ordownward position when activated. The turn signal control activation andcancellation is electronic. • To operate the left turn signal,push the lever down until it stopsand release. • To operate the right turn signal...

Rear dome/map lamps Your vehicle may have map lampswithin the rear dome lamp. Pressthe switches on either side of thedome lamp to turn the lamps on. BULB REPLACEMENT Lamp assembly condensation Exterior lamps are vented to accommodate normal changes in pressure.Condensation can be a natural by-produc...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Speed dependent wipers: When the wiper control is set on the intermittent settings, the speed of the wipers will automatically ...

TILT/TELESCOPE STEERING WHEEL To adjust the steering wheel: 1. Pull the lever down to unlock thesteering column. 2. While the lever is in the downposition, move the steering wheelup or down and in or out until youfind the desired position. 3. While holding the steering wheelin place, pull the lever ...

The power point can switch to a fault mode when it is overloaded,overheated, or shorted. For overloading and shorting conditions, unplugyour device and turn the ignition key off then on. For an overheatingcondition, let the system cool off, then turn the ignition key off then on. The 110V AC power p...

Rear Window Buffeting: When one or both of the rear windows are open, the vehicle may demonstrate a wind throb or buffeting noise. Thisnoise can be alleviated by lowering a front window approximately 2–3 in.(5–8 cm). One-touch down Allows the driver’s window to open fully without holding the control...

Accessory delay With accessory delay, the window switches may be used for up to10 minutes after the ignition switch is turned to the off position or untileither front door is opened. INTERIOR MIRROR The interior rearview mirror has two pivot points on the support armwhich lets you adjust the mirror ...

To adjust your mirrors: 1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror. 2. Move the control in the directionyou wish to tilt the mirror. 3. Return to the center position to lock mirrors in place. The spotter mirror below the ...

Mirror-mounted side turn signal indicator (if equipped) When the vehicle turn signals areactivated, the outer portion of themirror housing will blink amber. The turn signal feature can be seenby other drivers who may approachfrom the rear of the vehicle. Clearance lamps (if equipped) Illuminates whe...

The accelerator and brake pedal positions are saved when doing amemory set function and can be recalled along with the vehiclepersonality features when a memory position is selected. Refer to Memory seats/power mirrors/adjustable pedals in the Seating and Safety Restraints chapter. SPEED CONTROL (IF...

For further information on the SYNC 威 system, refer to the SYNC 威 supplement. Navigation system/SYNC 威 hands free control features (ifequipped) Press VOICE briefly until thevoice icon appears on the navigation display to use the voicecommand feature. Press to activate phone mode or answer a phone ca...

• Fixed code garage door openers were produced prior to 1996. Fixedcode uses the same coded signal every time. It is manuallyprogrammed by setting DIP switches for a unique personal code. If you do not know if your garagedoor opener is a rolling code orfixed code device, open your garagedoor opener’...

POSITIVE RETENTION FLOOR MAT (IF EQUIPPED) WARNING: Always use floor mats that are designed to fit the foot well of your vehicle. Only use floor mats that leave the pedal area unobstructed. Only use floor mats that are firmly secured toretention posts so that they cannot slip out of position and int...

1. Before removal of the tailgate,locate and disconnect the tailgatein-line connector under the pickupbox on the passenger side of thevehicle near the spare tire. 2. Install a protective cap (tetheredto the wire assembly) onto thein-line rearview camera systemconnector that remains under thepickup b...

3. Rotate the panels toward thetailgate. Repeat Steps 1–3 for the other side of the bed extender. 4. Connect the two panels, then rotate both knobs a quarter-turnclockwise to secure the panels. 5. Ensure the latch rod is insertedinto the tailgate hole and the lockingpins on both sides are engaged in...

KEYS Your vehicle may be equipped withtwo integrated keyhead transmitters(IKTs). The key blade functions as aprogrammed key which starts thevehicle and unlocks/locks all thedoors. The transmitter portionfunctions as the remote entrytransmitter. Your IKTs are programmed to your vehicle; using a non-p...

MyKey 威 restricted features Standard settings – These settings cannot be changed • The audio system will be muted whenever Belt-Minder 威 is activated until the safety belts are buckled. Refer to the Seating and Safety Restraints chapter for a detailed description of Belt-Minder 威 operation. • Low fu...

Refer to Message center in the Instrument Cluster chapter for MyKey 威 system warnings displays. Using MyKey 威 with remote start systems MyKey 威 is not compatible with non Ford-approved aftermarket remote start systems. If you choose to install a remote start system please seeyour authorized dealer f...

Keyless entry keypad autolock enable/disable procedure 1. Turn the ignition to the offposition. 2. Close all the doors. 3. Enter factory–set 5–digit entrycode. 4. Press and hold the 3 • 4. While holding the 3 • 4 press the 7 • 8. 5. Release the 7 • 8. 6. Release the 3 • 4. The user should receive a ...

The typical operating range for your IKT is approximately 33 feet(10 meters). A decrease in operating range could be caused by: • weather conditions, • nearby radio towers, • structures around the vehicle, or • other vehicles parked next to your vehicle. The IKT allows you to: • remotely unlock the ...

Switching from two step to one step door unlocking Your vehicle comes with two step unlocking enabled. Unlocking can beswitched between two step and one step door unlocking by pressing andholding both the and buttons simultaneously on the remote entry transmitter for approximately four seconds. The ...

Programming memory feature to transmitter To activate this feature: 1. Move the driver seat, power mirrors, and adjustable pedals to thedesired positions using the associated controls. 2. Press and hold control button 1for five seconds. A tone will beheard after two seconds confirmingmemory position...

Integrated keyhead transmitter (IKT) To replace the battery: 1. Twist a thin coin in the slot nearthe key ring to remove the batterycover (1). Note: Do not wipe off any grease on the battery terminals on the backsurface of the circuit board. 2. Carefully peel up the rubbergasket (2) from the transmi...

The remote start system will not work if: • The ignition is in the on position. • The alarm system is triggered. • The feature has been disabled. • The hood is not closed. • Two remote vehicle starts have already been attempted within the lasthour. • The vehicle is not in P (Park). Starting the engi...

The ignition switch must be turned to the on position and then back tothe off position or allow one hour to pass before using remote startagain. Turning the engine off after using remote start • Press one time. The parking lamps will turn off. You may have to be closer to the vehicle than when start...

SECURILOCK 姞 PASSIVE ANTI-THEFT SYSTEM (IF EQUIPPED) SecuriLock 威 passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from beingstarted unless a coded key programmed to your vehicle is used. The use of the wrong type of coded key may lead ...

Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by pressing the control on your remote entry transmitter. • Turn the ignition to the on position with a programmed coded ignitionkey. • Unlock the doors by using your keyless entry pad. • If using a ke...

WARNING: The non-adjustable head restraint is a safety device. It should be installed whenever the seat is occupied. WARNING: To minimize the risk of neck injury in the event of a crash, head restraints must be installed properly. Front seat • Lift the track release bar to movethe seat forward or re...

20 percent front seat armrest and console (if equipped) To release the armrest and gainaccess to the cupholders andseatback storage bin, press thebutton on the right-hand side of theseat and pull the seatback down. Pull up on the tab to open thestorage bin. Lift up on the seatback to return it to th...

The under-seat storagecompartment (if equipped) has aprogrammable lock. Use the ignitionkey to program the lock to thecompartment. Electronics may bepowered or charged using theunder-seat storage compartmentauxiliary power point. Refer to Auxiliary power point (12VDC) in the Drive Controls chapter. ...

Easy-access/easy-out feature (if equipped) The easy entry feature can be turned off or on through the vehiclemessage center. Refer to Message center in the Instrument Cluster chapter. The easy entry feature automatically moves the driver’s seat 2 inches(5 cm) forward when: • the transmission is in P...

Outboard head restraints (Crew Cab) Center head restraint (Crew Cab) The non-adjustable second row head restraints consist of : • a trimmed energy absorbing foam and structure (1), • two steel stems (2), • and two guide sleeve unlock/remove buttons (3). Removal of the second-row non-adjustable head ...

Rear under seat storage (if equipped) (Crew Cab) The rear seat has storage space located under the seat cushion. Lift up the lever and flip up the seatcushion to access the storage spaceand the power point (1). To remove the storage space divider,squeeze the sides and lift it from thestorage tub. Us...

SAFETY RESTRAINTS WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips. WARNING: To reduce the risk of injury, make sure children sit where they can be properly restrained. WARNING: Never let a passenger hold a child on his or her lap while the vehi...

WARNING: Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a childanywhere near them. WARNING: Front and rear seat occupants, including pregnant women, should wear safety belts fo...

While you are fastened in the safety belt, the combination lap/shoulderbelt with a cinch tongue adjusts to your movement. However, if youbrake hard, turn hard, or if your vehicle receives an impact of 5 mph(8 km/h) or more, the safety belt will become locked and help reduceyour forward movement. Res...

Automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to remove any slack in the shoulder belt. The automaticlocking mode is not available on the driver safety belt or the optionalfront or rear seat center safety belt. When to use the automati...

WARNING: BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the safety belt assembly “automatic locking retractor” feature or any other safety belt function is not operatingproperly when checked by an authorized dealer. Failure to replace thebelt and retractor assembly could increase the risk of injury...

Safety belt height adjustment Your vehicle has safety belt heightadjustments at the front outboardseating positions. Adjust the heightof the shoulder belt so the belt restsacross the middle of your shoulder. To adjust the shoulder belt height,pull on the center button and slidethe height adjuster do...

If... Then... The driver’s safety belt isbuckled before the ignitionswitch is turned to the onposition... The Belt-Minder 威 feature will not activate. The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... “Crashes are...

Reasons given... Consider... “The people I’m with don’twear belts” Set the example, teen deaths occur 4times more often in vehicles withTWO or MORE people. Children andyounger brothers/sisters imitatebehavior they see. “I have an airbag” Airbags offer greater protection whenused with safety belts. F...

WARNING: While the design allows you to deactivate your Belt-Minder 威 , this system is designed to improve your chances of being safely belted and surviving an accident. We recommend youleave the Belt-Minder 威 system activated for yourself and others who may use the vehicle. To reduce the risk of in...

WARNING: Never place your arm over the airbag module as a deploying airbag can result in serious arm fractures or other injuries. To properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching thepedals comfortably. • Recline the seat slightly...

WARNING: An infant in a rear-facing seat faces a high risk of serious or fatal injuries from a deploying passenger airbag. Rear facing infant seats should NEVER be placed in the front seats, unlessthe passenger airbag is turned off. See Passenger airbag ON/OFF switch. WARNING: Front seating position...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

WARNING: All occupants of the vehicle including the driver should always wear their safety belts even when an airbag SRS and Safety Canopy 威 System is provided. WARNING: To reduce risk of injury, do not obstruct or place objects in the deployment path of the inflatable Safety Canopy 威 . How does the...

restrained using a properly installed child or booster seat because it isdesigned to inflate downward from the headliner above the doors alongthe side window opening. The Safety Canopy system is designed to activate when the vehiclesustains lateral deceleration sufficient to cause the RCM to initiat...

A difficulty with the system is indicated by one or more of the following: • The readiness light (same light as for front airbag system) will eitherflash or stay lit. • The readiness light will not illuminate immediately after ignition isturned on. • A series of five beeps will be heard. The tone pa...

Turning the passenger airbag off 1. Insert the ignition key, turn theswitch to OFF position and hold inthe OFF position while removing thekey. 2. When the ignition is turned to theon position the “pass airbag off”light illuminates briefly, momentarilyshuts off and then turns back on.This indicates t...

2. Child age 1 to 12. A child age 1 to 12 must ride in the front seat because: • the vehicle has no rear seat; • although children ages 1 to 12 ride in the rear seat(s) wheneverpossible, children ages 1 to 12 sometimes must ride in the frontbecause no space is available in the rear seat(s) of the ve...

SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag supplemental restraint system (SRS) in this chapter for special instructions about using airbags. Important child restraint precautions WARNING: Always make ...

Recommendations for Safety Restraints for Children Child size, height, weight, or age Recommendedrestraint type Infantsortoddlers Children weighing 40 lb (18 kg) or less(generally age four or younger) Use a child safetyseat (sometimescalled an infantcarrier, convertibleseat, or toddlerseat). Smallch...

• When possible, always properly restrain children twelve (12) years ofage and under in a rear seating position of your vehicle. Accidentstatistics suggest that children are safer when properly restrained inthe rear seating positions than in a front seating position. Recommendations for attaching ch...

Transporting children Always make sure your child is secured properly in a device that isappropriate for their age, height and weight. All children are shapeddifferently. The child height, age and weight thresholds provided arerecommendations or the minimum requirements of law. The NationalHighway T...

SAFETY SEATS FOR CHILDREN Infant and/or toddler seats Use a safety seat that is recommended for the size and weight of thechild. When installing a child safety seat: • Review and follow the informationpresented in the Airbag supplemental restraint system(SRS) section in this chapter. • Carefully fol...

Installing the child safety seat Perform the following steps when installing the child seat in theoutboard combination lap/shoulder belts: Note: Although the child seat illustrated is a forward facing child seat, the steps are the same for installing a rear facing child seat. 1. Position the child s...

7. Try to pull the belt out of the retractor to make sure the retractor isin the automatic locking mode (you should not be able to pull more beltout). If the retractor is not locked, repeat Steps 5 and 6. 8. Remove remaining slack from thebelt. Force the seat down with extraweight, e.g., by pressing...

6. Attach the tether strap (if the child seat is equipped). Refer to Attaching child safety seats with tether straps later in this chapter. 7. Before placing the child in theseat, forcibly move the seat forwardand back to make sure the seat issecurely held in place. To checkthis, grab the seat at th...

• F-Series Crew Cab Attach the tether strap only to the appropriate tether anchor as shown.The tether strap may not work properly if attached somewhere otherthan the correct tether anchor. Once the child safety seat has been installed using the safety belt, youcan attach the top tether strap. Tether...

4. Remove tether cover. 5. Clip the tether strap to the anchor as shown. • Front seats (Regular Cab) • Rear seats (Crew Cab) If the tether strap is clipped incorrectly, the child safety seat may not beretained properly in the event of a collision. Seating and Safety Restraints 212 2012 F-250/350/450...

2. Attach the strap hook onto theloop behind an adjacent seatingposition. 3. Install the child safety seat tightlyusing the vehicle belts. Follow theinstructions in this chapter. 4. Tighten the tether strapaccording to the child seatmanufacturer’s instructions. A single loop can be used to route and...

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, and lets you adjust the shoulder belt to cross the chest and restsnugly near the center of the shoulder. The drawings below compare theideal fit (cente...

Follow all instructions provided by the manufacturer of the booster seat. WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the riskof injury or death in a collis...

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare encountered on streets,highways and off-road. Utilityvehicles and trucks are not designedfor cornering at speeds as high aspassenger cars any more tha...

Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary. Information on transfer case operation and shifting procedurescan be found in the Driving chapter. Information on transfer case maintenance can be f...

Treadwear The treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernment test course. For example, a tire graded 150 would wear oneand one-half (1 1 ⁄ 2 ) times as well on the government course as a tire graded 100. The ...

Note: Do not reduce tire pressure to change the ride characteristics of the vehicle. If you do not maintain the inflation pressure at the levelsspecified by Ford, your vehicle may experience a condition known as“shimmy”. Shimmy is a severe vibration and oscillation in the steeringwheel after the veh...

3. Add enough air to reach the recommended air pressure. Note: If you overfill the tire, release air by pushing on the metal stem in the center of the valve. Then recheck the pressure with your tire gauge. 4. Replace the valve cap. 5. Repeat this procedure for each tire, including the spare. Note: S...

WARNING: An inflated tire and rim can be very dangerous if improperly used, serviced or maintained. To reduce the risk of serious injury, never attempt to re-inflate a tire which has been run flator seriously under-inflated without first removing the tire from thewheel assembly for inspection. Do no...

other signs of damage or excessive wear. If internal damage to the tire issuspected, have the tire demounted and inspected in case it needs to berepaired or replaced. For your safety, tires that are damaged or showsigns of excessive wear should not be used because they are more likelyto blow out or ...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

Safety Practices WARNING: If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to fiveseconds. WARNING: Do not spin the wheels at over 35 mph (56 km/h). The tires may fa...

The tires should also be balanced periodically. An unbalanced tire andwheel assembly may result in irregular tire wear. Tire rotation Rotating your tires at the recommended interval (as indicated in the Scheduled Maintenance chapter) will help your tires wear more evenly, providing better tire perfo...

• Dual rear wheel (DRW) vehicles –Six tire rotation If your vehicle is equipped with dualrear wheels it is recommended thatthe front and rear tires (in pairs) berotated only side to side. We do notrecommend splitting up the dualrear wheels. Rotate them side toside as a set/pair. After tire rotation,...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

7. H: Indicates the tire’s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods oftime under a standard condition of load and inflation pressure. The tireson your vehicle may operate at different conditions for load and inflationpressure. The...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below. Note: Tire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the Tire a...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Grades donot apply ...

The tire pressure monitoring system complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that...

When your temporary spare tire is installed When one of your road tires needs to be replaced with the temporary spare,the TPMS will continue to identify an issue to remind you that the damagedroad wheel/tire needs to be repaired and put back on your vehicle.To restore the full functionality of the t...

Low tirepressurewarning light Possiblecause Customer action required Flashingwarning light Spare tire inuse Repair the damaged road wheel/tireand reinstall it on the vehicle torestore system functionality. For adescription on how the systemfunctions, refer to When your temporary spare tire is instal...

7. Remove the valve cap from the valve stem on the right front tire;decrease the air pressure until the horn sounds. 8. Remove the valve cap from the valve stem on the right rear tire;decrease the air pressure until the horn sounds. 9. Remove the valve cap from the valve stem on the left rear tire;d...

Follow these guidelines when using snow tires and chains: • If possible, avoid fully loading your vehicle. • Use only SAE Class S chains. • Install chains securely, verifying that the chains do not touch anywiring, brake lines or fuel lines. • Drive cautiously. If you hear the chains rub or bang aga...

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-Pillar or the edge of the driver’s door(vehicles exported outside the US and Canada may not have a TireLabel). Look for “THE COMBINED WEI...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehi...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label.The label shall be affixed to either the door hinge pillar,door-latch post, or the door edge that meets the doo...

• Example only: WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structuraldamage, serious damage to the vehicle, loss of control and personalinjury. Tires, Wheels and Lo...

GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo andpassengers – that the vehicle can handle without r...

WARNING: Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury. Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lb.” on your vehicle’s plac...

to transport the cement to your home? If you and your friend eachweigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12x 100) = 1400 - 440 - 1200 = - 240 lb. No, you do not have enoughcargo capacity to carry that much weight. In metric units, thecalculation would be: 635 kg - (2 x 9...

Towing a trailer places an additional load on your vehicle’s engine,transmission, axle, brakes, tires and suspension. Inspect thesecomponents carefully prior to and after any towing operation. Refer to Transmission fluid temperature gauge in the Instrument Cluster chapter for the transmission fluid ...

Vehicle type Rear axle ratio Maximum GCWR - lb (kg) F–250/F–350 Single Rear Wheel (SRW) 3.73 19000 (8617) 4.30 22000 (9977) F–350 Dual Rear Wheel (DRW) 3.73 19500 (8844) 4.30 22500 (10204) F–450/550 4.88 26000 (11791) Preparing to tow Use the proper equipment for towing a trailer and make sure it is...

Fifth-wheel and gooseneck towing Your vehicle may be equipped with a fifth-wheel prep package. Thispackage enables your vehicle to accept certain fifth-wheel trailer hitchesand gooseneck ball hitches. The fifth-wheel trailer hitch is attached tothe four mounting pads in the pick-up bed; an optional ...

If you use a rental trailer, follow the instructions that the rental agencygives to you. Do not attach safety chains to the bumper. Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes aresafe if installed properly and adjusted to the manufacturer’sspecifications. The tr...

The TBC user interface consists ofthe following: 1. +/- (GAIN adjustment buttons): Pressing these buttons adjusts the TBC’s power output tothe trailer brakes (in0.5 increments). The GAIN settingcan be increased to a maximum of10.0 or decreased to a minimum of 0 (no trailer braking). Pressing andhold...

activated while the brake is also applied, the greater of the two inputsdetermines the power sent to the trailer brakes. • Stop lamps: Activating the TBC manual control lever illuminates both the trailer brake lamps and the tow vehicle brake lamps except thecenter high-mount stop lamp (presuming pro...

Explanation of instrument cluster warning messages: The TBC interacts with the instrument cluster message center to displaythe following messages: TRAILER BRAKE MODULE FAULT: This message is displayed and accompanied by a single chime, in response to faults sensed by the TBC.In the event this messag...

• The TBC interacts with the brake system of the vehicle, includingABS, in order to reduce the likelihood of trailer wheel lock-up;therefore, if these systems are not functioning properly, the TBC maynot function at full performance. • Your vehicle’s brake system and the trailer brake system workind...

than the road tires on your vehicle, your spare tire is considered“temporary”. Consult information on the Tire Label or Safety ComplianceCertification Label for limitations when using. Trailer towing safety tips General • Ensure that the trailer, safety chains and 7–pin electrical connectorsare secu...

• The trailer brakes (including the shoes, drum and trailer brakemagnets) must be inspected and serviced at intervals specified by themanufacturer. • Electric brakes also require periodic adjustment to keep the shoesproperly spaced. If the brakes get hot when driving or if they will nothold, chances...

Note: Put your climate control system in recirculated air mode to prevent exhaust fumes from entering the vehicle. Refer to the Climate Controls chapter for more information. In case of a roadside emergency with a disabled vehicle, see Wrecker towing in the Roadside Emergencies chapter. These guidel...

Before using the recovery hooks: • Make sure all attaching points are secure and capable of withstandingthe applied load. • Never use chains, cables or tow straps with metal hook ends. • Only use recovery straps that have a minimum breaking strength twoto three times the GVW of the stuck vehicle. • ...

STARTING Positions of the ignition 1. Off— shuts off the engine and allaccessories/locks the steering wheeland allows key removal. Note: In order to switch off the engine whilethe vehicle is in motion, shift toneutral and use the brakes to bringthe vehicle to a safe stop. After thevehicle has stoppe...

WARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. WARNING: Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Alwa...

Note: Cranking may be stopped at any time by turning the key to the off position.3. After idling for a few seconds, release the parking brake, apply thebrake, shift into gear and drive. Note: If the engine does not start on the first try, turn the key to the off position, wait 10 seconds and try Ste...

2. When the engine starts, release the key, then gradually release theaccelerator pedal as the engine speeds up. If the engine still fails to start,repeat Step 1. Guarding Against Exhaust Fumes WARNING: If you smell exhaust fumes inside your vehicle, have this checked immediately. Do not drive your ...

Prior to using the engine block heater, follow these recommendations forproper and safe operation: • For your safety, use an outdoor extension cord that is productcertified by Underwriter’s Laboratory (UL) or Canadian StandardsAssociation (CSA). Use only an extension cord that can be usedoutdoors, i...

of power per hour. Your factory installed block heater system does nothave a thermostat; however, maximum temperature is attained afterapproximately three hours of operation. Block heater operation longerthan three hours will not improve system performance and willunnecessarily use additional electr...

application is detected, the system will remain activated as long as thebrake pedal is pressed or ABS is engaged. The system is deactivated byeither releasing the brake pedal or coming to a complete stop. When thesystem activates, noise from the ABS pump motor and brake pedalpulsation may be observe...

The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated until theparking brake is released. Pull the release lever to release theparking brake. To prevent the pedalfrom releasing too quickly, placeyour left foot on the service brakepedal, then slowly pull the releaselever ...

WARNING: Hill descent control cannot control descent in all surface conditions and circumstances, such as ice or extremely steep grades. Hill descent control is a driver assist system and cannotsubstitute for good judgment by the driver. Failure to do so may resultin loss of vehicle control, crash o...

Hill descent modes • At speeds below 20 mph (32 km/h): When the HDC switch is pressedand HDC is active, the HDC telltale will flash. • At speeds below 20 mph (32 km/h): When the HDC switch is pressedand conditions are not correct for hill descent activation, the HDCsystem will be enabled, the light ...

If any steering components are serviced or replaced, install newfasteners (many are coated with thread adhesive or have prevailingtorque features which may not be re-used). Never re-use a bolt or nut.Torque fasteners to specifications in Workshop Manual . A high crown in the road or high crosswinds ...

For 2WD vehicles and vehiclesequipped with a manual shift4WD system: Turn the control to ON. Theindicator light will display in theinstrument cluster. Once the light is displayed in the instrument cluster, both rear wheel axle shafts will be locked together providing added traction. If the indicator...

WARNING: Vehicles with a higher center of gravity such as utility vehicles and trucks handle differently than vehicles with a lower center of gravity. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slungsports cars are designed to per...

WARNING: If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. See your authorized dealer as soon as possible. AUTOMATIC TRANSMISSION OPERATION Understanding the shift positions of the 5–speed automatictransmission (if equippe...

WARNING: Do not use the tow/haul feature when driving in icy or slippery conditions as the increased engine braking can cause the rear wheels to slide and the vehicle to swing around with thepossible loss of vehicle control. 3 (Third) Transmission starts and operates in third gear only. Used for imp...

To return to normal D (Overdrive) position, move the shift lever backfrom M to D. • The transmission will operate in gears one through six. 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additionalengine braking on downgrades. 1 (First) • Provides maximum engine braking. • All...

All available gears will be displayed with the current gear indicated.Press the – button again to lock out gears beginning with the highestgear. Example: press the – button twice to lock out 6th and 5th gears.Only the available gears will be displayed and the transmission willautomatically shift bet...

If Your Vehicle Gets Stuck in Mud or Snow Note: Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur. Note: Do not rock the vehicle for more than a minute or damage to the transmission and tires may occur, or the engine may overheat. If...

• (1) Rear bumper • (2) Red zone • (3) Yellow zone • (4) Green zone • (5) Centerline of vehicle Always use caution while backing. Objects in the red zone are closestto your vehicle and objects in thegreen zone are further away. Objectsare getting closer to your vehicle as they move from the green zo...

4WD operation is not recommended on dry pavement. Doing so couldresult in difficult disengagement of the transfer case, increased tire wearand decreased fuel economy. Manual Shift On Stop (MSOS) 4x4 system (if equipped) The 4WD system is engaged ordisengaged by rotating the controlfor both front whe...

• auto-manual hub locks can bemanually overridden by rotatingthe hub lock control from AUTOto LOCK if desired. • automatic operation of thehub locks is recommended, and will increase fuel economy • For proper operation, makesure that each hub is fullyengaged and that both hublocks are set to the sam...

2H (2WD) – For general on-road driving. Sends power to the rear wheels only should be used for street and highway driving. Providesoptimal smoothness and fuel economy at high speeds. 4H (4x4 High) – Used for extra traction such as in snow or icy roads or in off road situations. This mode is not inte...

Shifting from 4H (4x4 High) to 2H (2WD) Move the transfer case lever to 2H(2WD) at a stop or a vehicle speedbelow 3 mph (5 km/h). With the vehicle at complete stop,disengage the locking hubs(optional) by rotating the hub lockcontrol from LOCK to FREE. • For proper operation, makesure that both indic...

3. Move the transfer case shift leverthrough N (Neutral) directly to 4H(4x4 High) or 2H (2WD). 4. If the transfer case will not engage into 4H (4x4 High) or 2H(2WD), perform a shift with thetransmission in N (Neutral) and thevehicle rolling at a speed below3 mph (5 km/h). 5. If shifting to 2H (2WD) ...

Note: Some noise may be heard as the system shifts or engages; this is normal. Note: 4x4 low mode is not intended for use on dry pavement. Driving off-road with truck and utility vehicles 4WD vehicles are specially equipped for driving on sand, snow, mud andrough terrain and have operating character...

• Be extremely careful when driving on pavement made slippery byloose sand, water, gravel, snow or ice. If your vehicle goes off the edge of the pavement • If your vehicle goes off the edge of the pavement, slow down, butavoid severe brake application, ease the vehicle back onto thepavement only aft...

WARNING: Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a passenger or bystander. Refer to Gauges in the Instrument Cluster chapter for transmission fluid temperature information. Emergency maneuvers • In an unavoidable emergency situation where a sudden sharp turnmus...

Mud and water If you must drive through highwater, drive slowly. Traction orbrake capability may be limited. When driving through water,determine the depth; avoid waterhigher than the bottom of the hubs(if possible) and proceed slowly. Ifthe ignition system gets wet, thevehicle may stall. Once throu...

Driving on hilly or sloping terrain Although natural obstacles may make it necessary to travel diagonally upor down a hill or steep incline, you should always try to drive straight upor straight down. Avoid driving crosswise or turning on steep slopes or hills . A danger lies in losing traction, sli...

Failure to maintain your vehicle properly may void the warranty, increaseyour repair cost, reduce vehicle performance and operational capabilitiesand adversely affect driver and passenger safety. Frequent inspection ofvehicle chassis components is recommended if the vehicle is subjected toheavy off-...

Operating the vehicle with the snowplow attached Do not use your vehicle for snow removal until it has been driven atleast 500 miles (800 km). The attached snowplow blade restricts airflow to the radiator, and maycause the engine to run at a higher temperature: Attention to enginetemperature is espe...

ROADSIDE ASSISTANCE Vehicles sold in the U.S. : Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24-hours,...

U.S. Ford vehicle customers who require Roadside Assistance, call1-800-241-3673. If you need to arrange roadside assistance for yourself, Ford MotorCompany will reimburse a reasonable amount for towing to the nearestdealership within 35 miles (56 km). To obtain reimbursementinformation, U.S. Ford ve...

FUEL PUMP SHUT-OFF In the event of a moderate to severe collision, this vehicle is equippedwith a fuel pump shut-off feature that stops the flow of fuel to theengine. Not every impact will cause a shut-off. Should your vehicle shut off after a collision due to this feature, you mayrestart your vehic...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Protected Circuits 1 30A Not used (spare) 2 15A Upfitter relay #4 3 30A Not used (spare) 4 10A Interior lights, Hood lamp 5 20A Moon roof 6 5A Driver seat module 7 7.5A Driver seat switch, Driver lumbarmotor 8 10A Power mirror switc...

Power distribution box The power distribution box is located in the engine compartment. Thepower distribution box contains high-current fuses that protect yourvehicle’s main electrical systems from overloads. WARNING: Always disconnect the battery before servicing high current fuses. WARNING: To red...

Fuse/Relay Location Fuse Amp Rating Protected Circuits 92 20A* Auxiliary power point #4 93 20A* Auxiliary power point #3 94 25A* Upfitter #1 95 25A* Upfitter #2 96 50A* ABS pump 97 40A* Invertor 98 — Not used 99 — Not used 100 25A* Trailer tow turn signals 101 Relay Starter 102 Relay Trailer tow bat...

WARNING: The use of tire sealants may damage your tire pressure monitoring system (TPMS) and should not be used. However, if you must use a sealant, the TPMS sensor and valve stemon the wheel must be replaced by an authorized Ford dealer. WARNING: Refer to Tire pressure monitoring system (TPMS) in t...

Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability It is...

Spare tire informationNote: If your vehicle is equipped the tire pressure monitoring system (TPMS), the system indicator light will illuminate when the spare is inuse. To restore the full functionality of the TPMS system, all road wheelsequipped with the tire pressure monitoring sensors must be moun...

Tool Location Jack handle, lug wrench, lugwrench extension (only availableon Dual Rear Wheel [DRW]vehicles) and wheel chock (onlyavailable on Single Rear Wheel[SRW] vehicles equipped with adiesel engine) Regular cab: Fastened to floorbehind driver seatSuperCab: Fastened to floor underrear seatCrew C...

2. Attach the spare tire lock key (A)to the jack handle (B). 3. Fully insert the jack handle (withone extension) through the bumperhole and into the guide tube. Thekey and lock will engage with aslight push and counterclockwiseturn. Some resistance will be feltwhen turning the jack handleassembly. 4...

WARNING: To prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block (in both directions) the wheel that is diagonally opposite (other side andend of the vehicle) to the tire being changed. WARNING: If the vehicle slips off the jack, you or someone else co...

13. Insert the jack handle into thepump linkage. 14. Use an up-and-down motionwith the jack handle to raise thewheel completely off the ground. Hydraulic jacks are equippedwith a pressure release valvethat prevents lifting loads whichexceed the jack’s rated capacity. 15. Remove the lug nuts with the...

10–lug nut torque sequence 19. Stow the flat tire. Refer to Stowing the flat/spare tire if the vehicle is equipped with a spare tire carrier. 20. Stow the jack, jack handle and lug wrench. Make sure the jack issecurely fastened so it does not rattle when driving. 21. Unblock the wheels. The followin...

If the ornament retention towers arealigned between the studs/lug nuts,the ornament is improperlyinstalled. This improper installationmay appear and sound correct, butwill not keep the ornament on thevehicle. Ornaments improperlyinstalled in this manner will fall offor become loose with minimal forc...

JUMP STARTING WARNING: The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. WARNING: Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted. Do not attempt to push-start your aut...

Connecting the jumper cables Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery. 1. Connect the positive (+) jumpercable to the positive (+) terminal ofthe discharged battery. 2. Connect the other end of thepositive (+) cable to the positive(+)...

Jump Starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that the vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingbe...

Note: Towing an ESOF 4x4 vehicle with the front wheels on the ground without disengaging the front hubs may cause damage to the automatictransmission. Note: Towing a 4x2 or an ESOF 4x4 vehicle with the rear wheels on the ground for more than 50 miles (80 km) and/or in excess of 35 mph(56 km/h) may c...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizeddealer. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfaction. Plea...

• Ford Genuine Accessories • Service specials and promotions. In Canada: Mailing address Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Additional assistance If you have questions or concerns,...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft 威 Detail Wash (ZC-3-A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can ...

• Do not spray a hot engine with cold water to avoid cracking theengine block or other engine components. • Spray Motorcraft 威 Engine Shampoo and Degreaser (ZC-20) on all parts that require cleaning and pressure rinse clean. • Never wash or rinse the engine while it is hot or running; water in theru...

• 6.8L V10 gasoline engine PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your authorized dealer. • For routine cleaning, use Motorcraft 威 Detail Wash (ZC-3-A). • If tar or grease spots are present, use Motorcraft 威 Bug and Ta...

• The wiper blades can be cleaned with isopropyl (rubbing) alcohol orMotorcraft 威 Premium Windshield Washer Concentrate (ZC-32-A) in the U.S., or Premium Quality Windshield Washer Fluid [CXC-37-(A, B,D, or F)] in Canada, available from your authorized dealer. Thiswasher fluid contains special soluti...

LEATHER SEATS FOR THE KING RANCH 姞 EDITION ONLY (IF EQUIPPED) Your vehicle is equipped with seating covered in premium, top-grainleather which is extremely durable, but still requires special care andmaintenance in order to ensure longevity and comfort.Regular cleaning and conditioning will maintain...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide to find out wh...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel. 2. Go to the front of the vehicle torelease the auxiliary latch located atthe top center of the grille. Slide thehandle left to release the auxiliarylatch. 3. Lift the hood...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specifications. Do not use anyspecial washer fluid such aswindshield water repellent type fluidor bug wash. They may causesque...

Poor wiper quality can be improved by cleaning the wiper blades and thewindshield. Refer to Windows and wiper blades in the Cleaning chapter. To prolong the life of the wiper blades, it is highly recommended toscrape off the ice on the windshield before turning on the wipers. Thelayer of ice has man...

• Oil levels above the upper hole may cause engine damage. Some oilmust be removed from the engine by a service technician. 7. Put the dipstick back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If ...

To protect your engine and engine’s warranty, use Motorcraft 威 SAE 5W-20 or an equivalent SAE 5W-20 oil meeting Ford specificationWSS-M2C945-A. SAE 5W-20 oil provides optimum fuel economy and durability performance meeting all requirements for yourvehicle’s engine. Refer to Maintenance product speci...

If you see any corrosion on the battery or terminals, remove the cablesfrom the terminals and clean with a wire brush. You can neutralize theacid with a solution of baking soda and water. It is recommended that the negative battery cable terminal bedisconnected from the battery if you plan to store ...

Because your vehicle’s engine is electronically controlled by a computer,some control conditions are maintained by power from the battery. Whenthe battery is disconnected or a new battery is installed, the engine mustrelearn its idle and fuel trim strategy for optimum driveability andperformance. To...

ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant should be checked at theintervals listed in scheduled maintenance information. The coolant concentration should be maintained at 50/50 coolant and distilled water.For best results, coolant concentration should be te...

• Do not add extra inhibitors or additives to the coolant. These can be harmful and compromise the corrosion protection of the enginecoolant. For vehicles with overflow coolant systems with a non-pressurized capon the coolant recovery system, add coolant to the coolant recoveryreservoir when the eng...

If you have to add more than 1.0 quart (1.0 liter) of engine coolant permonth, have your authorized dealer check the engine cooling system.Your cooling system may have a leak. Operating an engine with a lowlevel of coolant can result in engine overheating and possible enginedamage. Recycled engine c...

If you drive in extremely hot climates: • It is still necessary to maintain the coolant concentrationabove 40%. • NEVER decrease the coolant concentration below 40%. • Decreased engine coolant concentrations below 40% willdecrease the corrosion/freeze protection characteristics of theengine coolant ...

Once the engine temperature cools, the engine can be re-started. Takeyour vehicle to an authorized dealer as soon as possible to minimizeengine damage. When fail-safe mode is activated You have limited engine power when in the fail-safe mode, so drive thevehicle with caution. The vehicle will not be...

WARNING: To reduce the risk of collision and injury, be prepared that the vehicle speed may reduce and the vehicle may not be able to accelerate with full power until the fluid temperaturesreduce. The air conditioning may also cycle on and off during severe operatingconditions to protect overheating...

WARNING: Flexible fuel components and standard unleaded gasoline fuel components are not interchangeable. If your vehicle is not serviced in accordance with flexible fuel vehicles procedures,damage may occur and your warranty may be invalidated. WARNING: When refueling always shut the engine off and...

Your vehicle was not designed to use fuel or fuel additives with metalliccompounds, including manganese-based additives. Note: Use of any fuel other than those recommended may cause powertrain damage, a loss of vehicle performance, and repairs may notbe covered under warranty. Octane recommendations...

problems continue, fill the vehicle with regular unleaded gasoline anddrive vehicle normally until gasoline is used. See your authorized dealerif the problem persists. Do not add aftermarket fuel additive products to your fuel tank. Itshould not be necessary to add any aftermarket products to your f...

ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, thedriver. You must gather information as accurately and consistently aspossible. Fuel expense, frequency of fill-ups or fuel gauge readings areNOT accurate as a measure of fuel eco...

2. Each time you fill the tank, record the amount of fuel added (ingallons or liters). 3. After at least three to five tank fill-ups, fill the fuel tank and recordthe current odometer reading. 4. Subtract your initial odometer reading from the current odometerreading. 5. Follow one of the simple cal...

EMISSION CONTROL SYSTEM WARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. WARNING: Exhaust leaks may result in entry of harmful and potentially lethal fumes into th...

POWER STEERING FLUID Check the power steering fluid. Refer to scheduled maintenance information. If adding fluid is necessary, use only MERCON 威 ATF. • Gasoline engine shown; dieselengine similar. Refer to Identifying components in theengine compartment in the diesel supplement. Check the fluid leve...

BRAKE FLUID • Vacuum boost system • Hydroboost system The fluid level will drop slowly as the brakes wear, and will rise when thebrake components are replaced. Fluid levels between the top of the MINand MAX lines are within the normal operating range; there is no need toadd fluid. If the fluid level...

TRANSFER CASE FLUID (IF EQUIPPED) 1. Clean the filler plug. 2. Remove the filler plug andinspect the fluid level. 3. Add only enough fluid throughthe filler opening so that the fluidlevel is at the bottom of theopening. Use only fluid that meets Ford specifications. Refer to the Maintenance product ...

The following procedure is for vehicles equipped with a gasoline engine.If your vehicle is equipped with a diesel engine, refer to the dieselsupplement. Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. Changing the air filter element 1. Lo...

10. Reconnect the mass air flowsensor electrical connector to theoutlet tube. Make sure the lockingtab on the connector is in the“locked” position (connector shownfrom below for clarity). Note: Failure to use the correct air filter element may result in severeengine damage. The customerwarranty may ...

• Move vehicles at least 25 feet (8 m) every 15 days to lubricateworking parts and prevent corrosion. Removing vehicle from storage When your vehicle is ready to come out of storage, do the following: • Wash your vehicle to remove any dirt or grease film build-up onwindow surfaces. • Check windshiel...

FORD CUSTOM ACCESSORIES FOR YOUR VEHICLE A wide selection of Ford Custom Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement the ...

FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY) More than 32 million Ford and Lincoln owners have discovered thepowerful protection of Ford ESP. It is the only extended service planbacked by Ford Motor Company, and provides “peace of mind”protection beyond the New Vehicle Limited Warranty coverage. Up t...

FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY) You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is the only service contractbacked by Ford Motor Company of Canada, Limited. Depending on theplan you purchase, Ford ESP provides benefits such as: • R...

GENERAL MAINTENANCE INFORMATION The following information pertains to 6.2L V8 and 6.8L V10 gasolineengines only. Scheduled maintenance for the diesel engine can be foundin the diesel supplement. Why maintain your vehicle? Carefully following this schedule helps protect against major repairexpenses r...

Ford strongly recommends the use of genuine Ford replacement parts.Parts other than Ford, Motorcraft 威 or Ford-authorized remanufactured parts that are used for maintenance replacement or for the service ofcomponents affecting emission control must be equivalent to genuineFord Motor Company parts in...

Genuine Ford and Motorcraft 姞 replacement parts Dealerships stock Ford and Motorcraft 威 branded replacement parts. These parts meet or exceed Ford Motor Company’s specifications, andwe stand behind them. Parts installed at your dealership carry anationwide, 12 month/12,000 mile (20,000 km) parts and...

Multi-point inspection – Recommended each visit Accessory drive belt(s) Half-shaft dust boots (if equipped) Battery performance Horn operation Clutch operation (if equipped) Radiator, cooler, heater and A/C hoses Engine air filter Suspension component for leaks ordamage Exhaust system Steering and l...

NORMAL SCHEDULED MAINTENANCE AND LOG The following section contains the “Normal Schedule”. This schedule ispresented at specific mileage (kilometer) intervals with exceptionsnoted. Scheduled Maintenance 429 2012 F-250/350/450/550 (f23) Owners Guide, 3rd PrintingUSA (fus)

Maintenance Schedule Log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ...

SPECIAL OPERATING CONDITIONS The following information pertains to 6.2L V8 and 6.8L V10 gasolineengines only. Scheduled maintenance for the diesel engine can be foundin the diesel supplement. If you operate your vehicle primarily in one of the more demanding conditions listed below, you will need to...

Operating in dusty conditions such as unpaved or dusty roads Inspect frequently,service as required Replace cabin air filter (if equipped) Replace engine air filter Every 5,000 miles(8,000 km) Inspect the wheels and related components forabnormal noise, wear, looseness or drag Rotate tires*, inspect...

Off-road operation Inspect frequently,service as required Inspect steering linkage, ball joints and U-joints;lubricate if equipped with grease fittings Replace cabin air filter (if equipped) Replace engine air filter Every 5,000 miles(8,000 km) or6 months Change engine oil and filter Inspect wheels ...

Special Operating Condition Log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D A...

EXCEPTIONS There are several exceptions to the Normal Schedule. They are listedbelow: Normal vehicle axle maintenance: Rear axles and power take-off (PTO) units with synthetic fluid and light-duty trucks equipped withFord-design axles are lubricated for life; do not check or change fluidunless a lea...

Edge/MKX AWD only – vehicles operating off-road in sand during high ambient temperatures must replace the AWD PTU (All-wheel drivePower Transfer Unit) lube every 20,000 miles (32,000 km). Engine air filter & cabin air filter replacement: Engine air filter and cabin air filter life is dependent o...

A Accessory delay ........................106 AdvanceTrac ..............................277 Airbag supplemental restraintsystem ........................182, 186, 188 and child safety seats ............183description ..............182, 186, 188disposal ....................................196driver ai...

checking and adding ..............375dipstick ....................................375filter, specifications ........376, 409recommendations ...................376refill capacities ........................410 Event data recording ....................8 Exhaust fumes ..........................271 F Fai...

Washer fluid ..............................374 Water, Driving through .............315 Windows power .......................................104 Windshield washer fluid andwipers ..........................................99 checking and adding fluid .....374replacing wiper blades ...........374 Wreck...