Ford 2012 Expedition v.2- User Manual

DATA RECORDING Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, st...

CELL PHONE USE The use of mobile communications equipment has become increasinglyimportant in the conduct of business and personal affairs. However,drivers must not compromise their own or others’ safety when usingsuch equipment. Mobile communications can enhance personal safetyand security when app...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Instrument cluster shown in standard measure; metric similar. Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Ma...

Solid illumination after the engine is started indicates the on-boarddiagnostics system (OBD-II) has detected a malfunction. Refer to On-board diagnostics (OBD-II) in the Maintenance and Specifications chapter. If the light is blinking, engine misfire is occurring which coulddamage your catalytic co...

WARNING: Driving a vehicle with the brake system warning light on is dangerous. A significant decrease in braking performance may occur. It will take you longer to stop the vehicle.Have the vehicle checked by your authorized dealer. Driving extendeddistances with the parking brake engaged can cause ...

Transmission Tow/Haul Feature(RTT): Displays when the Tow/Haul feature has been activated. Refer tothe Driving chapter for transmission function and operation. If the light flashes steadily, have thesystem serviced immediately, damage to the transmission could occur. AdvanceTrac 威 /Traction control ...

Four-wheel drive auto (RTT) (ifequipped): Displays when four-wheel drive automatic mode isengaged. If the light fails to displaywhen the ignition is turned on, orremains on, have the system serviced immediately by your authorizeddealer. Door ajar (RTT) (if equipped): Displays when the ignition is in...

GAUGES Instrument cluster shown in standard measure; metric similar. 1. Tachometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scalemay damage the engine. 2. Battery voltage gauge: Indicates the battery voltage when the i...

Distance to empty is calculated using a running average fuel economy,which is based on your recent driving history of 500 miles (800 km).This value is not the same as the average fuel economy display. Therunning average fuel economy is re-initialized to a factory default value ifthe battery is disco...

Compass calibration adjustment NOTE: For optimum calibration, drive to an open, level location away from large metallic objects or structures. Switch off all non-essentialelectrical accessories (heated rear window, heater, A/C, map lamps,wiper, etc.) and make sure all the doors are closed. 1. Start ...

UNITS ENG / METRIC Displays the current units English or Metric. Press and hold the SELECT/RESET stem to change from English to Metric. Press the SELECT/RESET stem for the next SETUP MENU item or waitfor more than four seconds to return to the INFO MENU. AUTOLAMP This feature keeps your headlights o...

TIMER Timer displays the trip elapsed drive time. To operate, do the following: 1. Press and release RESET in order to start the timer. 2. Press and release RESET to pause the timer. 3. Press and hold RESET until the timer resets. System check and vehicle feature customization Press the SETUP button...

COMPASS The compass heading is displayed as one of N, NE, E, SE, S, SW, W andNW in the message center display. The compass reading may be affected when you drive near largebuildings, bridges, power lines and powerful broadcast antenna. Magneticor metallic objects placed in, on or near the vehicle ma...

AUDIO SYSTEMS AM/FM single CD/MP3 satellite compatible sound system(if equipped) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that maytake their focus off the r...

Track/Folder mode: Available only on MP3 discs in CD mode. In Track mode, pressing SEEK, SEEK will scroll through all tracks on the discIn Folder mode, pressing SEEK, SEEK will scroll only through tracks within the selected folder.Press FOLDER, FOLDER to access the previous/next folder (if available...

In TEXT MODE, press SEEK, SEEK to view the previous/additional display text. Satellite radio is available only with a valid SIRIUS 威 radio subscription. Check with your authorized dealer for availability. 6. / OK(Play/Pause): This control is operational in CD andDVD mode (if equipped). When aCD or D...

11. REW (Rewind): In CD mode, press REW to manually reverse in atrack.In DVD mode (if equipped), press and hold to reverse through thecurrent chapter. 12. Memory presets: To set a station, select the desired frequencyband, AM, FM1 or FM2. Tune to thedesired station. Press and hold a preset button un...

Your vehicle is equipped with anAuxiliary Input Jack (AIJ) locatedinside the center console. TheAuxiliary Input Jack provides a wayto connect your portable musicplayer to the in-vehicle audiosystem. This allows the audio from aportable music player to be playedthrough the vehicle speakers withhigh f...

1. MEDIA: Push repeatedly to cycle through available playing mediassuch as AM, FM1, FM2, CD, SAT1,SAT2, SAT3 (satellite radio ifequipped), DVD (if equipped) andSYNC 威 (if equipped). If in Dual Play mode, SHARED illuminates in theradio display when the front andrear modes are set to the samemedia. No...

Parental control The multimedia system allows forthree varying levels of parentalcontrol over rear-seat controls. Bysimultaneously pressing the 3 and 5 buttons, the rear passengers may beallowed to access FULL or LOCAL control or be LOCKED out of rearseat controls altogether. After the ignition has ...

The front speakers remain playing for the front passengers. Press thespeaker button, or the 2/4 preset buttons simultaneously on the radioagain to deactivate the headphones and dual play mode. The wordsSINGLE PLAY will illuminate on the radio display and fade control andsound from rear speakers will...

• Wipe discs from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periodsof time. • Clean using a circular motion. CD units are designed to play commercially pressed 4.75 in(12 cm) audio compact discs only. Due to technicalincompatibility, certain recordable and...

MP3 track and folder structure Your MP3 system recognizes MP3 individual tracks and folder structureas follows: • There are two different modes for MP3 disc playback: MP3 track mode(system default) and MP3 folder mode. For more information on trackand folder mode, refer to Sample MP3 structure in th...

NAVIGATION SYSTEM (IF EQUIPPED) Your vehicle may be equipped with a navigation system. Refer to the Navigation System supplement for further information. SYNC 姞 (IF EQUIPPED) Your vehicle may be equipped with SYNC 威 , a hands-free communications and entertainment system with special phone and media ...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) 1. Temperature selection: Controls the temperature of theairflow in the vehicle. 2. Air flow selections: Controls the direction of the airflow in thevehicle. See the following for a briefdescription on each control. MAX A/C: Distributes recircu...

4. REAR Rear temperature control: Press to enable the auxiliary system and to set the desired rear cabin airflow temperaturewith the front control. The rear cabin airflow temperature will match thedriver airflow temperature setting when only the center rear temperaturelight ( REAR ) is illuminated. ...

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITH REARPASSENGER COMPARTMENT CLIMATE CONTROL (IF EQUIPPED) 1. Defrost: Distributes outside air through the windshield defroster vents and demister vents. Can be used to clear thin ice or fog from thewindshield. 2. Rear temperature control: Press to enable th...

REAR WINDOW DEFROSTER R The rear defroster control is locatedon the climate control panel andworks to clear the rear window offog and thin ice. The engine must be running to operate the rear window defroster. Press the control to turn the rear window defroster on. An indicator lighton the button wil...

HEADLAMP CONTROL Rotate the headlamp control to thefirst position to turn on the parking lamps. Rotate to the second position to turn on the headlamps. Rotate back to to turn the headlamps off. Autolamp control The autolamp system provides lightsensitive automatic on/off control ofthe exterior light...

High beams • Push the lever toward theinstrument panel to activate. • Pull the lever toward you todeactivate. Flash-to-pass Pull toward you slightly to activateand release to deactivate. Daytime running lamps (DRL) (if equipped) Turns the headlamps on at reduced intensity output. To activate: • the ...

PANEL DIMMER CONTROL Use to adjust the brightness of theinstrument panel and all applicableswitches in the vehicle duringheadlamp and parking lampoperation. Move the control to the full uprightposition, past detent, to turn on theinterior lamps. Move the control to the full downposition, past detent...

2. Measure the height from the center of your headlamp (indicated by a3.0 mm circle on the lens) to the ground and mark an 8 foot (2.4 meter)horizontal reference line on the vertical wall or screen at this height (apiece of masking tape works well). 3. Turn on the low beam headlamps to illuminate th...

INTERIOR LAMPS Front row map lamps (if equipped) To turn on the map lamps, press theouter edge of the clear lens. Thefront row map lamp lights when: • any door is opened. • the instrument panel dimmerswitch is rotated until thecourtesy lamps come on. • the remote entry controls arepressed and the ig...

Rear cargo lamp The dome lamp lights when: • any door is opened, and theswitch is in the middle position. • the instrument panel dimmerswitch is rotated until thecourtesy lamps come on. • any of the remote entry controlsare pressed and ignition is off (andswitch is in the middle position). With the ...

Replacing exterior bulbs Check the operation of all the bulbs frequently. Replacing headlamp bulbs 1. Make sure that the headlamp control is in the off position. 2. Open the hood. 3. At the back of the headlamp,remove the two headlamp assemblyretainer bolts. 4. Slide headlamp assembly forwardand off...

Replacing front parking lamp/turn/sidemarker signal bulbs 1. Make sure that the headlamp control is in the off position.2. Open the hood. 3. At the back of the headlamp,remove the two headlamp assemblyretainer bolts. 4. Slide headlamp assembly forwardand off the retaining tab to exposethe back of th...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Speed dependent wipers: When the wiper control is on, the speed ofthe wipers will automatically adjustwith the vehicle speed. T...

Courtesy wipe feature: One extra wipe will occur a few seconds after washing the front window to clear any excess washer fluid remaining onthe windshield. Note: Do not operate the washer when the washer reservoir is empty. This may cause the washer pump to overheat. Check the washer fluidlevel frequ...

TILT STEERING WHEEL 1. Pull and hold the steering wheelrelease control toward you. 2. Move the steering up or downuntil you find the desired location. 3. Release the steering wheelrelease control. This will lock thesteering wheel in position. WARNING: Never adjust the steering column when the vehicl...

OVERHEAD CONSOLE The appearance of your vehicle’s overhead console will vary according toyour option package. Forward storage bin (if equipped) The storage compartment may beused to store a pair of sunglasses.Press the release area on the rearedge of the bin door to open thestorage compartment. The ...

Note: The 110V AC power point is equipped with a cap which providesprotection from inserting objects intothe socket. The cap should always bein a closed position whenever thepower point outlet is not in use. The 110V AC power point is locatedon the back of the center console. The power outlet is not...

One-touch up or down (driver’s window only) This feature allows the driver’s window to open or close fully withoutholding the control down. To operate one-touch down, press the switch completely down to thesecond detent and release quickly. The window will open fully.Momentarily press the switch to ...

INTERIOR MIRROR The interior rearview mirror has two pivot points on the support armwhich lets you adjust the mirror up or down and from side to side. WARNING: Do not adjust the mirror while the vehicle is in motion. Automatic dimming interior rear view mirror The interior rear view mirror has an au...

The power-folding mirrors may be moved inward/outward manually.However, if a mirror is moved manually, it will need to be reset. A mirrorwhich has not been reset may appear to be loose. To reset: with theswitch in the center position, momentarily pull the switch rearward tofold the mirrors in. An au...

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is in the P (Park) position. Press and hold the rocker control toadjust accelerator and brake pedal. • Press the top of the control toadjust the pedals ...

SPEED CONTROL With speed control set, you can maintain a set speed without keepingyour foot on the accelerator pedal. WARNING: Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved. Using speed control The speed controls are located on the steering wheel. Th...

STEERING WHEEL CONTROLS (IF EQUIPPED) Audio control features MEDIA: Press repeatedly to scroll through available audio modes. SEEK: Press to select the previous/next radio stationpreset, CD track or satellite radiostation preset depending on whichmedia mode you are in. + VOL – (Volume): Press to inc...

For further information on the SYNC 威 system, refer to the SYNC 威 supplement. Navigation system/SYNC 威 hands free control features (ifequipped) Press VOICE briefly until thevoice icon appears on the Navigation display to use the voicecommand feature. Press to activate phone mode or answer a phone ca...

Bounce-back: When an obstacle has been detected in the moon roof opening as the moon roof is closing, the moon roof will automaticallyopen and stop at a prescribed position. Bounce-back override: To override bounce-back function, pull and hold the SLIDE switch within two seconds of a bounce-back eve...

If you do not know if your garagedoor opener is a rolling code orfixed code device, open your garagedoor opener’s remote control batterycover. If a panel of DIP switches ispresent your garage door opener isa fixed code device. If not, yourgarage door opener is a rolling codedevice. Note: Programming...

POSITIVE RETENTION FLOOR MAT WARNING: Always use floor mats that are designed to fit the foot well of your vehicle. Only use floor mats that leave the pedal area unobstructed. Only use floor mats that are firmly secured toretention posts so that they cannot slip out of position and interferewith the...

WARNING (Continued) • Failure to properly follow floor mat installation or attachmentinstructions can potentially cause interference with pedal operationcausing loss of control of vehicle. • To install floor mats, position the floor mat so that the eyelet is overthe retention post and press down to ...

Note: Cycling the ignition prior to completely latching the liftgate could result in damage to the liftgate and/or its power components. Make surethe liftgate is fully latched before operating the vehicle. Care should be exercised in starting the engine before the liftgate is fullyclosed (latched). ...

To close the liftgate with therear cargo area control button: Press and release the control on theleft rear quarter panel to close theliftgate. The chime will beep once ifconditions are not correct to startan operation (i.e., the vehicle is outof park). In a normal close, thechime will begin just be...

Liftgate window To open the liftgate window, pressthe button in the center of theliftgate above the license plate. MANUAL LIFTGATE (IF EQUIPPED) The liftgate area is only intended for cargo, not passengers. You can openand close the liftgate from outside the vehicle. The liftgate cannot beopened fro...

WARNING: Do not load any objects on the shelf that may obstruct your vision or strike occupants of the vehicle in the case of a sudden stop or collision. WARNING: Do not place people or pets on or under the parcel shelf. LUGGAGE RACK Your vehicle is equipped with a roofrack for transporting items on...

KEYS Your vehicle may be equipped withtwo integrated keyhead transmitters(IKTs). The key blade functions as aprogrammed key which starts thevehicle and unlocks/locks all thedoors. The transmitter portionfunctions as the remote entrytransmitter. Your IKTs are programmed to your vehicle; using a non-p...

MYKEY 姞 The MyKey 威 feature allows you to program a restricted driving mode to promote good driving habits. All but one of the keys programmed to thevehicle can be activated as a MyKey 威 . The key will remain restricted until MyKey 威 is cleared. Any remaining keys are referred to as an “administrato...

3. Press and release the RESET button. HOLD RESET TO CONFIRMCLEAR is displayed. 4. Press and hold the RESET button for two seconds until ALL MYKEYSCLEARED is displayed. Check MyKey 威 system status The vehicle system check will provide the status of the following MyKey 威 parameters: • MYKEY MILES — T...

POWER DOOR LOCKS Press control to unlock all doors. Press control to lock all doors. Smart locks This feature helps to prevent you from locking yourself out of the vehicleif your key is still in the ignition. When you open one of the front doors or the liftgate and you lock thevehicle with the power...

Keyless entry keypad procedure 1. Turn the ignition to the off position. 2. Close all doors, the liftgate and liftgate window. 3. Enter 5–digit entry code 4. Press and hold the 3 • 4. While holding the 3 • 4 press the 7 • 8. 5. Release the 7 • 8. 6. Release the 3 • 4. The user should receive a horn ...

Power door lock switch autounlock enable/disable procedure Before starting, ensure the ignition is in the off position and all vehicledoors are closed. You must complete Steps 1–5 within 30 seconds or theprocedure will have to be repeated. If the procedure needs to berepeated, wait a minimum of 30 s...

WARNING: Make sure the power liftgate is closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out. If you must drive withthe liftgate open, keep the vents open so outside air comes into thevehicle. Car finder Press twice within t...

3. Within three seconds press the . 4. A tone will be heard when the transmitter programming is complete. 5. Press the . 6. Repeat this procedure for memory 2 and another transmitter if desired. Deprogramming memory feature from the transmitter To deactivate this feature: 1. Press and hold either th...

Replacing lost integrated keyhead transmitters (IKTs) If you would like to have your integrated keyhead transmittersreprogrammed because you lost one, or would like to buy additionalIKTs, you can either reprogram them yourself, or take all IKTs to your authorized dealer for reprogramming. How to rep...

SECURILOCK 姞 PASSIVE ANTI-THEFT SYSTEM SecuriLock 威 passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from beingstarted unless a coded integrated keyhead transmitter (IKT) programmed to your vehicle is used. The use of the wrong type of ...

Anti-theft indicator The anti-theft indicator is located in the instrument panel cluster. • When the ignition is in the offposition, the indicator will flashonce every two seconds to indicatethe SecuriLock 威 system is functioning as a theft deterrent. • When the ignition is in the on position, the i...

The turn signal lamps will flash once when all doors, the hood and theliftgate are closed indicating the vehicle is locked and entering the20 second countdown. Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by using the remote entry transmitter por...

Properly adjust the head restraint so that the top of the head restraint iseven with the top of your head and positioned as close as possible to theback of your head. For occupants of extremely tall stature, adjust thehead restraint to its full up position. WARNING: To minimize the risk of neck inju...

Note: On vehicles with memory seats, to prevent damage to the seat, the power seats are designed to set a stopping position just short of theend of the seat track. If the seat encounters an object while movingforward or backward, a new stopping position will be set. To reset theseat to its normal st...

Climate Controlled Seats (if equipped) Note: It is recommended for optimal performance that the vehicle air conditioning system be run in the same mode (either heating or cooling)as the climate control seat system. During start-up of the climate controlseat system, a slight difference in seat surfac...

Cooled Seats The cooled seats will only function when the engine is running. To operate the cooled seats: Press the cooled seat symbol tocycle through the various coolingsettings and off. Cooler settings areindicated by more indicator lights. If the engine falls below 350 RPMs while the cooled seats...

3. Remove filter. To install a filter: • First, position the filter in itshousing making sure that the farforward end is all the way up inthe housing. Then push in on thecenter of the outside edge of thefilter and rotate up into thehousing until it clips into position. REAR SEATS Second and third ro...

The non-adjustable head restraintsconsist of: • a trimmed energy absorbing foamand structure (1), • and a fold strap (2). To fold the outboard head restraint, pull the fold strap. To place thehead restraint back to the upright position, pull up on the head restraint. Second row center seat head rest...

Folding Down the 2nd Row 40% Seat System WARNING: Use caution when folding the seatback to the flat back position as the system will move forward when you lift the release handle. WARNING: Before returning the seatback to its original position, make sure that cargo or any objects are not trapped beh...

To return the seat to the upright position: 1. Lift the seatback toward the rearof the vehicle. 2. Rotate the seatback until youhear a click, locking it in the uprightposition. 3. Lift up on the head restraint untilit locks into its original position. Placing the 2nd Row Outboard 40% Seats in Cargo ...

WARNING: Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. After returning the seatback to its originalposition, pull on the seatback to ensure that it has fully latched. Anunlatched seat may become dangerous in the event...

Note: If a squeak is heard from the latch area, the latch striker pinshould be wiped clean of dust ordebris. Exiting the 3rd Row 1. Pull the strap located at thebottom outboard of the seat back torelease the seat from the floor, androtate the seat up towards the frontseat. 2. Follow the directions a...

Note: Do not do the following: • Place heavy objects on the seat • Operate the seat heater if water or any other liquid is spilled on theseat. Allow the seat to dry thoroughly. The rear seat heat controls are located on the rear of the center console. The heated seats only operate when the ignition ...

Note : Be sure that the head restraints are folded down beforepowering the 3rd row seat down. The control buttons are located onthe right-hand rear quarter trimpanel (accessible from the liftgatearea). Press the bottom portion of thecontrol button to lower the desiredseatback. Press the top of the c...

RESTRAINT SAFETY SYSTEM The restraint system provides an improved overall level of frontal crashprotection to front seat occupants and is designed to help further reducethe risk of airbag-related injuries. The system is able to analyze differentoccupant conditions and crash severity before activatin...

Determining if the restraint system is operational The restraint system uses a warning light in the instrument cluster or aback-up tone to indicate the condition of the system. Refer to the Warning lights and chimes section in the Instrument Cluster chapter. Routine maintenance of the restraint syst...

Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest tothe direction the tongue is coming from) until you hear a snap and feel itlatch. Make sure the tongue is securely fastened in the buckle. • Front and rear seats 2. To unfasten, push the release ...

Restraint of pregnant women WARNING: Always ride and drive with your seatback upright and the safety belt properly fastened. The lap portion of the safety belt should fit snug and be positioned low across the hips. Theshoulder portion of the safety belt should be positioned across thechest. Pregnant...

When to use the automatic locking mode This mode should be used any time a child safety seat, except a booster, is installed in passenger front or rear seating positions. Children12 years old and under should be properly restrained in a rear seatingposition whenever possible. Refer to Safety restrai...

Safety belt pretensioner Your vehicle is equipped with safety belt pretensioners at the driver andright front passenger seating positions. The safety belt pretensioner removes some slack from the safety beltsystem at the start of a crash. The safety belt pretensioner uses thesame crash sensor system...

Second Row Comfort Guide WARNING: Position the safety belt comfort guide so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the safetybelt and increase the risk of injury in a collision. The second row outboard lap ...

Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and achime sounds to remind the occupants to fasten their safety belts. Conditions of operation If... Then... The driver safety belt is notbuckled before the ignitionswitch is turned to ...

If... Then... The driver’s safety belt is notbuckled approximately fiveseconds after the safety beltwarning light has turned off... The Belt-Minder 威 feature is activated - the safety belt warning light illuminatesand the warning chime sounds for sixseconds every 30 seconds, repeatingfor approximate...

Reasons given... Consider... “Safety belts don’t work” Safety belts, when used properly, reduce risk of death to front seat occupants by 45% in cars, and by 60% in light trucks. “Traffic is light” Nearly 1 of 2 deaths occur insingle-vehicle crashes, many when no other vehicles are around. “Belts wri...

Children and airbags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating position. Failure to followthese instructions may increase therisk of injury in a collision. WARNING: Airb...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

• one or more impact and safing sensors and diagnostic monitor (RCM), • a readiness light and tone • the electrical wiring which connects the components. The RCM (restraints control module) monitors its own internal circuitsand the supplemental airbag electrical system wiring (including theimpact se...

Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Refer to the Airbag readiness section in the Instrument Cluster chapter. Routine maintenance of the airbag is not required. Any difficulty with the syst...

SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag supplemental restraint system (SRS) in this chapter for special instructions about using airbags. Important child restraint precautions WARNING: Always make ...

Recommendations for attaching child safety restraints for children RestraintType Child Weight Use any attachment method as indicated below by “X” LATCH(loweranchorsandtoptetheranchor) LATCH(loweranchorsonly) Safetybeltandtoptetheranchor Safetybelt andLATCH(loweranchorsand toptetheranchor) Safetybelt...

WARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision, which may result in serious injury ordeath. WARNING: Never use pillows, books, or towels to boost a child. They can slide around and increase ...

Follow all the safety restraint and airbag precautions that apply to adultpassengers in your vehicle. If the child is the proper height, age, and weight (as specified by yourchild safety seat or booster manufacturer), fits the restraint and can berestrained properly, then restrain the child in the c...

Perform the following steps when installing the child seat withcombination lap/shoulder belts: Note: Although the child seat illustrated is a forward facing child seat, the steps are the same for installing a rear facing child seat. 1. Position the child safety seat in aseat with a combination lap a...

Combining safety belt and LATCH lower anchors for attachingchild safety seats When used in combination, either the safety belt or the LATCH loweranchors may be attached first, provided a proper installation is achieved.Attach the tether strap afterward, if included with the child seat. Referto Recom...

Once the child safety seat has been installed using either the safety belt,the lower anchors of the LATCH system, or both, you can attach the toptether strap. If you install a child seat with rigid LATCH attachments, and haveattached the top tether strap to the proper top tether anchor, do nottighte...

Third row center seating position 1. Route the child safety seat tether strap over the back of the seat. 2. Locate the anchor webbing loop for the seating position. • You may need to pull back thetop of the hinged panel along thebottom of the seat back to accessthe tether anchor. 3. Clip the tether ...

If your child restraint system is equipped with a tether strap, and thechild restraint manufacturer recommends its use, Ford also recommendsits use. Child booster seats The belt-positioning booster (booster seat) is used to improve the fit ofthe vehicle safety belt. Children outgrow a typical child ...

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, and lets you adjust the shoulder belt to cross the chest andrest snugly near the center of the shoulder. The drawings below comparethe ideal fit (cente...

Follow all instructions provided by the manufacturer of the booster seat. WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the riskof injury or death in a collis...

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare encountered on streets,highways and off-road. Utilityvehicles and trucks are not designedfor cornering at speeds as high aspassenger cars any more tha...

VEHICLE CHARACTERISTICS Four-wheel drive (4WD) system (if equipped) A vehicle equipped with 4WD (when selected) has the ability to use allfour wheels to power itself. This increases traction which may enable youto safely drive over terrain and road conditions that a conventionaltwo-wheel drive vehic...

How Your Vehicle Differs from Other Vehicles SUVs and trucks can differ fromsome other vehicles in a fewnoticeable ways. Your vehicle maybe: • Higher – to allow higher loadcarrying capacity and to allow itto travel over rough terrainwithout getting hung up ordamaging underbody components. • Shorter ...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING Tire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperature A These Tire Quality G...

You are strongly urged to buy a reliable tire pressure gauge, as automaticservice station gauges may be inaccurate. Ford recommends the use of adigital or dial-type tire pressure gauge rather than a stick-type tirepressure gauge. Use the recommended cold inflation pressure for optimum tireperformanc...

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, ...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

Safety Practices WARNING: If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to fiveseconds. WARNING: Do not spin the wheels at over 35 mph (56 km/h). The tires may fa...

The tires should also be balanced periodically. An unbalanced tire andwheel assembly may result in irregular tire wear. Tire Rotation Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanicalproblem involved before tir...

INFORMATION CONTAINED ON THE TIRE SIDEWALL Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identifi...

6. 95: Indicates the tire’s load index. It is an index that relates to how much weight a tire can carry. You may find this information in yourowner’s guide. If not, contact a local tire dealer. Note: You may not find this information on all tires because it is not required by federal law. 7. H: Indi...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Grades donot apply ...

replacement or alternate tires or wheels on the vehicle that prevent theTPMS from functioning properly. Always check the TPMS malfunctiontelltale after replacing one or more tires or wheels on your vehicle toensure that the replacement or alternate tires and wheels allow theTPMS to continue to funct...

To restore the full functionality of the tire pressure monitoring system,have the damaged road wheel/tire repaired and remounted on yourvehicle. For additional information, refer to Changing tires with a TPMS in this section. When You Believe Your System Is Not Operating Properly The main function o...

Low tirepressurewarning light Possible cause Customer action required Flashingwarning light Spare tire in use Repair the damaged road wheel/tire and reinstall it on the vehicle torestore system functionality. For adescription on how the systemfunctions, refer to When your temporary spare tire is ins...

SNOW TIRES AND CHAINS WARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety andperformance of your vehicle, which could result in an increased risk ofloss of vehicle control, ve...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehi...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label.The label shall be affixed to either the door hinge pillar,door-latch post, or the door edge that meets the doo...

• Example only: WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structuraldamage, serious damage to the vehicle, loss of control and personalinjury. Tires, Wheels and Lo...

GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo andpassengers – that the vehicle can handle without r...

WARNING: Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tireswith a higher limit than the original tires do not increase the GVWRand GAWR limitations. WARNING: Exceeding any vehicle ...

TRAILER TOWING Trailer towing puts additional loads on your vehicle’s engine, transmission,axle, brakes, tires and suspension. For your safety and to maximize vehicleperformance, be sure to use the proper equipment while towing. Follow these guidelines to ensure safe towing: • Do not tow a trailer u...

Note: Before towing a trailer, make sure the trailer brakes (if equipped) and lamps are properly connected and functional. If equipped withelectronic trailer brakes, refer to the instructions provided by theaftermarket electronic brake controller manufacturer for determiningtrailer brake functionali...

Preparing to tow Use the proper equipment for towing a trailer and make sure it isproperly attached to your vehicle. Contact your authorized dealer or areliable trailer dealer as soon as possible if you require assistance. Hitches Do not use a hitch that clamps onto the vehicle’s bumper; use aload-c...

Driving while you tow When towing a trailer: • Do not drive faster than 70 mph (113 km/h) during the first 500 miles(800 km) of trailer towing and don’t make full-throttle starts. • Turn off the speed control. The speed control may shut offautomatically when you are towing on long, steep grades. • A...

Launching or Retrieving a Boat or Personal Water Craft (PWC) Note: Disconnect the wiring to the trailer before backing the trailer into the water. Note: Reconnect the wiring to the trailer after the trailer is removed from the water. When backing down a ramp during boat launching or retrieval:1. Do ...

STARTING Positions of the ignition 1. Off— locks the steering wheel,automatic transmission gearshiftlever and allows key removal. Note: In order to switch off the engine while the vehicle is inmotion, shift to neutral and use thebrakes to bring the vehicle to a safestop. After the vehicle has stoppe...

Starting the engine 1. Turn the key to 3 (on) withoutturning the key to 4 (start). 2. Turn the key to 4 (start), thenrelease the key as soon as theengine begins cranking. Your vehiclehas a computer assisted crankingsystem that assists in starting theengine. After releasing the key fromthe 4 (start) ...

Do not use starting fluid such as ether in the air intake system. Suchfluid could cause immediate explosive damage to the engine and possiblepersonal injury. If you should experience cold weather starting problems on E85 ethanol,and neither an alternative brand of E85 ethanol nor an engine blockheat...

ENGINE BLOCK HEATER (IF EQUIPPED) If your vehicle is factory-equippedwith an engine block heater, arubber cap/plug assembly will bevisibly attached to the grille on thefront of the vehicle. This assembly isshipped in-vehicle for authorizeddealer installation. If notfactory-equipped, the engine block...

• Use a 16 gauge outdoor extension cord, minimum. • Use as short an extension cord as possible. • Do not use multiple extension cords. Instead, use one extension cordwhich is long enough to reach from the engine block heater cord tothe outlet without stretching. • Make certain that the extension cor...

BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance information for scheduled maintenance. Occasional brake noise is normal and often does not indicate aperformance concern with the vehicle’s brake system. In normaloperation, automotive brake systems may emit occasional...

Using ABS • In an emergency or when maximum efficiency from the four-wheelABS is required, apply continuous force on the brake. The four-wheelABS will be activated immediately, thus allowing you to retain steeringcontrol of your vehicle and, providing there is sufficient space, willenable you to avo...

Apply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops. The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned on) until theparking brake is released. The parking b...

Certain adverse driving maneuvers may activate the ESC system, whichinclude but are not limited to: • Taking a turn too fast • Maneuvering quickly to avoid an accident, pedestrian or obstacle • Driving over a patch of ice or other slippery surfaces • Changing lanes on a snow-rutted road • Entering a...

Note: The trailer sway control will only activate at speeds greater than 40 mph (64 km/h). Disabling trailer sway control Trailer sway control can be disabled during any key cycle. See Message center in the Instrument Cluster chapter. Note that regardless of chosen enable state, trailer sway control...

PREPARING TO DRIVE WARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles. WARNING: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Utility vehicles and trucks have larger tires and increased gro...

Brake-shift interlock – floor-shift transmission This vehicle is equipped with a brake-shift interlock feature that preventsthe gearshift lever from being moved from P (Park) when the ignition isin the on position unless the brake pedal is pressed. If you cannot move the gearshift lever out of P (Pa...

FORWARD AND REVERSE SENSING SYSTEMS (IF EQUIPPED) The forward and reverse sensing system will warn the driver of obstacleswithin a certain range of the front and rear bumpers. The front sensors will be activewhen the gearshift is in any positionother than P (Park) or N (Neutral)and the vehicle speed...

Note: If the system cannot be turned off, refer to MyKey 威 in the Locks and Security chapter for more information. The system defaults to enabled every time the ignition is switched on. Press the control to disable or enable the system Keep the sensors (located on the front and rear bumper/fascia)fr...

Objects in the red zone are closest to your vehicle and objects in thegreen zone are further away. Objects are getting closer to your vehicle asthey move from the green zone to the yellow or red zones. Use the side mirrors and rearview mirror to get better coverage on bothsides and rear of the vehic...

BLIND SPOT MIRRORS Blind spot mirrors have an integrated convex spotter mirror built intothe upper outboard corner of the outside mirrors. They are designed toassist the driver by increasing visibility along the side of the vehicle. Formore information on your side view mirrors, refer to Exterior mi...

CONTROL TRAC FOUR-WHEEL DRIVE (4X4) OPERATION(IF EQUIPPED) WARNING: For important information regarding safe operation of this type of vehicle, see Preparing to drive your vehicle in this chapter. If equipped with the Control Trac 威 4X4 System, and 4L (4X4 LOW) is selected while the vehicle is movin...

• 4X4 LOW - Illuminates when 4L is selected. • CHECK 4X4 (if equipped) - Displays when a 4X4 fault ispresent. Note: When a 4x4 system fault is present, the system will typically remain in whichever 4X4 mode was selected prior to the fault conditionoccurring. It will not default to 4X2 mode in all ci...

Note: If your vehicle is equipped with AdvanceTrac 威 with RSC 威 , the AdvanceTrac 威 with RSC 威 system will automatically turn off the stability enhancement feature when you shift the Control Trac 威 four-wheel drive system into 4L (4X4 LOW). The brake traction enhancement feature willstill be enabled...

Basic operating principles • Do not use 4H (4X4) or 4L (4X4 LOW) on dry, hard surfaced roads.Doing so will produce excessive noise, increased tire wear and maydamage drive components. 4H (4X4) and 4L (4X4 LOW) are onlyintended for consistently slippery or loose surfaces. Use of 4H (4X4)or 4L (4X4 LO...

Do not rock the vehicle if the engine is not at normal operatingtemperature or damage to the transmission may occur. Do not rock the vehicle for more than a few minutes or damage tothe transmission and tires may occur or the engine may overheat. WARNING: Always set the parking brake fully and make s...

Mud and water If you must drive through highwater, drive slowly. Traction orbrake capability may be limited. When driving through water,determine the depth; avoid waterhigher than the bottom of the hubs(if possible) and proceed slowly. If the ignition system gets wet, thevehicle may stall. Once thro...

slopes or hills . A danger lies in losing traction, slipping sideways and possibly rolling over. Whenever driving on a hill, determine beforehandthe route you will use. Do not drive over the crest of a hill withoutseeing what conditions are on the other side. Do not drive in reverseover a hill witho...

DRIVING THROUGH WATER If driving through deep or standingwater is unavoidable, proceed veryslowly. Never drive through waterthat is higher than the bottom ofthe wheel rims (for cars) or thebottom of the hubs (for trucks). When driving through water, traction or brake capability may be limited.Also, ...

ROADSIDE ASSISTANCE Vehicles sold in the U.S. : Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24-hours,...

Vehicles sold in the U.S. : Using roadside assistance Complete the roadside assistance identification card and place it in yourwallet for quick reference. This card is found in the owner’s informationportfolio in the glove compartment. U.S. Ford vehicle customers who require Roadside Assistance, cal...

FUEL PUMP SHUT-OFF SWITCH FUEL RESET The fuel pump shut-off switch is a device intended to stop the electricfuel pump when your vehicle has been involved in a substantial jolt. After a collision, if the engine cranks but does not start, the fuel pumpshut-off switch may have been activated. The fuel ...

FUSES AND RELAYS Fuses If electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinthe fuse. Check the appropriatefuses before replacing any electricalcomponents. Note: Always replace a fuse with one that has the specified amperage r...

Passenger Compartment Fuse Panel The fuse panel is located under the right-hand side of the instrumentpanel. To remove the trim panel for accessto the fuse box, pull the paneltoward you and swing it out awayfrom the side and remove it. Toreinstall it, line up the tabs with thegrooves on the panel, t...

Power distribution box The power distribution box is located in the engine compartment. Thepower distribution box contains high-current fuses that protect yourvehicle’s main electrical systems from overloads. WARNING: Always disconnect the battery before servicing high current fuses. WARNING: To red...

CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily.Instead, gradually decrease your speed. Hold the steering wheel firmlyand slowly move to a safe place on the side of the road. Note: The tire pressure monitoring system (TPMS) indicator light will illuminate when...

• Winter weather driving capability • Wet weather driving capability • All-wheel driving capability (if applicable) • Load leveling adjustment (if applicable) When driving with the full-size dissimilar spare tire/wheel additionalcaution should be given to: • Towing a trailer • Driving vehicles equip...

Tire change procedure WARNING: To help prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block the wheels (both front or both rear) on the opposite end of the vehiclefrom the wheel being changed. If on a grade, block both oppositewheels on the downward si...

Stowing the spare tire 1. Lay the tire on the ground, near the rear of the vehicle, with the valvestem side facing up. 2. Slide the wheel partially underthe vehicle and install the retainerthrough the wheel center. Ifequipped, you may have to removethe wheel center cap prior topushing the retainer t...

WHEEL LUG NUT TORQUE SPECIFICATIONS WARNING: When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum orbrake disc that contacts the wheel. Ensure that any fasteners thatattach the roto...

RUNNING OUT OF FUEL If you have run out of fuel and need to refill the vehicle with a portablefuel container, see Running out of fuel in the Maintenance and Specifications chapter for proper fuel filling method using a portable fuel container and the included fuel filler funnel. Do not insert the no...

Preparing your vehicle When the battery is disconnected or a new battery is installed, theautomatic transmission must relearn its shift strategy. As a result, thetransmission may have firm and/or soft shifts. This operation isconsidered normal and will not affect function or durability of thetransmi...

4. Make the final connection of thenegative (-) cable to the jumpstarting stud located in the enginecompartment, near the washer fluidbottle. Note: Do not attach the negative (-) cable to fuel lines, engine rocker covers, the intake manifold or electrical components as grounding points. WARNING: Do ...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery. 1. Remove the jumper cable fromthe jump starting stud. 2. Remove the jumper cable on thenegati...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

Ford Motor Company produces a towing manual for all authorized towtruck operators. Have your tow truck operator refer to this manual forproper hook-up and towing procedures for your vehicle. Emergency Towing In case of a roadside emergency with a disabled vehicle (without accessto wheel dollies, car...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizeddealer. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfaction. Plea...

• Ford Genuine Accessories • Service specials and promotions. In Canada: Mailing address Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Additional assistance If you have questions or concerns,...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft 威 Detail Wash (ZC-3-A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can ...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with ...

WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, substances on thevehicle’s glass or the wiper blades may be the cause. These may includehot wax treatments used by commercial car washes, water repellen...

LEATHER SEATS FOR THE KING RANCH 姞 EDITION ONLY (IF EQUIPPED) Your vehicle is equipped with seating covered in premium, top-grainleather which is extremely durable, but still requires special care andmaintenance in order to ensure longevity and comfort. Regular cleaning and conditioning will maintai...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide to find out wh...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel. 2. Go to the front of the vehicle andrelease the auxiliary latch that islocated under the front center ofthe hood. 3. Lift the hood until the liftcylinders hold it open. Maintenance a...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 5.4L V8 1. Windshield washer fluid reservoir 2. Engine oil dipstick 3. Brake fluid reservoir 4. Engine coolant reservoir 5. Air filter assembly 6. Power steering fluid reservoir 7. Power distribution box 8. Engine oil filler cap 9. Battery Maintenance...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specifications. Do not use anyspecial washer fluid such aswindshield water repellent type fluidor bug wash. They may causesque...

CHANGING THE WIPER BLADES Replace wiper blades at least once per year for optimum performance. To replace the wiper blades: 1. Fold back the wiper arm andposition the wiper blade at rightangles to the wiper arm. 2. To remove, press the retainingclip (A) to disengage the wiperblade, then pull the bla...

4. To attach the new wiper to thewiper arm, align the cross pin andkeyway (denoted with the arrows)and firmly press the wiper bladeinto the wiper arm until an audiblesnap is heard. If you find this procedure too difficult, please see your dealer. ENGINE OIL Checking the engine oil Refer to the sched...

• If the oil level is below this mark, engine oil must be added to raise the level within thenormal operating range. • If required, add engine oil to the engine. Refer to Adding engine oil in this chapter. • Do not overfill the enginewith oil. Oil levels above thismark may cause enginedamage. If the...

Engine oil and filter recommendations Look for this certificationtrademark. Use SAE 5W-20 engine oil Only use oils certified for gasoline engines by the American PetroleumInstitute (API). An oil with this trademark symbol conforms to thecurrent engine and emission system protection standards and fue...

BATTERY Your vehicle is equipped with a Motorcraft 威 maintenance-free battery which normally does not require additional water during its life ofservice. Note: If your battery has a cover/shield, make sure it isreinstalled after the battery hasbeen cleaned or replaced. For longer, trouble-free opera...

7. Drive the vehicle to complete the relearning process. • The vehicle may need to be driven 10 miles (16 km) or more torelearn the idle and fuel trim strategy. • If you do not allow the engine to relearn its idle trim, the idlequality of your vehicle may be adversely affected until the idletrim is ...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the FULL COLD level, or within theCOLD FILL or MIN / MAX range as listed on the engine coolantreservoir (depending upon application). • Refer to scheduled maintenance information for serv...

• DO NOT MIX different colors or types of coolant in your vehicle. Make sure the correct coolant is used. Mixing of engine coolants mayharm your engine’s cooling system. The use of an improper coolantmay harm engine and cooling system components and may void thewarranty. Refer to Maintenance product...

3. Step back while the pressure releases. 4. When you are sure that all the pressure has been released, use thecloth to turn it counterclockwise and remove the cap. 5. Fill the coolant reservoir slowly with the proper coolant mixture, towithin the FULL COLD level, or within the COLD FILL or MIN / MA...

Severe climates If you drive in extremely cold climates: • It may be necessary to increase the coolant concentrationabove 50%. • NEVER increase the coolant concentration above 60%. • A coolant concentration of 60% will provide improved freezepoint protection. Increased engine coolant concentrations ...

If the engine reaches a preset over-temperature condition, the enginewill automatically switch to alternating cylinder operation. Each disabledcylinder acts as an air pump and cools the engine. When this occurs the vehicle will still operate. However: • The engine power will be limited. • The air co...

WARNING: Flexible fuel components and standard unleaded gasoline fuel components are not interchangeable. If your vehicle is not serviced in accordance with flexible fuel vehicles procedures,damage may occur and your warranty may be invalidated. WARNING: When refueling always shut the engine off and...

Easy Fuel 姞 “no cap” fuel system Your fuel tank is equipped with an Easy Fuel 威 “no cap” fuel filler system. This allows you to simply open the fuel filler door and insert the fuelfiller nozzle into the fuel system. The Easy Fuel 威 system is self-sealing and protected against dust, dirt, water and s...

Flex fuel vehicle (FFV) fuel fill inlet Flex fuel vehicles have a yellow bezel placed over the fuel fill inlet. Choosing the right fuel Use only UNLEADED FUEL and FUEL ETHANOL (Ed75–Ed85). The use of leaded fuel is prohibited by law and could damage yourvehicle. Your vehicle was not designed to use ...

Fuel quality Unleaded gasoline engines If you experience starting, rough idle or hesitation driveability problemsduring a cold start, try a different brand of “Regular” unleaded gasoline. FFV engines If you experience starting, rough idle or hesitation driveability problemsduring a cold start, try a...

ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, thedriver. You must gather information as accurately and consistently aspossible. Fuel expense, frequency of fill-ups or fuel gauge readings areNOT accurate as a measure of fuel eco...

Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers). 2. Each time you fill the tank, record the amount of fuel added (ingallons or liters). 3. After at least three to five tank fill-ups, fill the fuel tank and recordthe current od...

EMISSION CONTROL SYSTEM WARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. WARNING: Exhaust leaks may result in entry of harmful and potentially lethal fumes into th...

POWER STEERING FLUID Check the power steering fluid. Refer to scheduled maintenance information. 1. Start the engine and let it rununtil it reaches normal operatingtemperature (the engine coolanttemperature gauge indicator will benear the center of the normal areabetween H and C). 2. While the engin...

TRANSMISSION FLUID Checking automatic transmission fluid The automatic transmission does not have a transmission fluid dipstick. Refer to your scheduled maintenance information for scheduled intervals for fluid checks and changes. Your transmission does notconsume fluid. However, the fluid level sho...

8. Replace the air filter housingcover and secure the clamps. Becareful not to crimp the filterelement edges between the air filterhousing and cover and ensure thatthe tabs on the edge are properlyaligned into the slots. 9. Slip the air tube onto the air filterhousing and tighten the air-tubeclamp b...

VEHICLE STORAGE If you plan on storing your vehicle for an extended period of time(30 days or more), refer to the following maintenance recommendationsto ensure your vehicle stays in good operating condition. All motor vehicles and their components were engineered and tested forreliable, regular dri...

Removing vehicle from storage When your vehicle is ready to come out of storage, do the following: • Wash your vehicle to remove any dirt or grease film build-up onwindow surfaces. • Check windshield wipers for any deterioration. • Check under the hood for any foreign material that may have collecte...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintDevices and their location 3. Make, vehicle line, series, bodytype 4. Engine type 5. Check digit 6. Model year 7. Assembly plant ...

FORD CUSTOM ACCESSORIES FOR YOUR VEHICLE A wide selection of Ford Custom Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement the ...

Peace of mind • Remote start • Vehicle security systems • Back up alarm* • Wheel locks • Locking gas plug for capless fuel system • Bumper and hitch mounted parking sensors* *Ford Licensed Accessories (FLA) are warranted by the accessorymanufacturer’s warranty. Ford Licensed Accessories are fully de...

FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY) More than 32 million Ford and Lincoln owners have discovered thepowerful protection of Ford ESP. It is the only extended service planbacked by Ford Motor Company, and provides “peace of mind”protection beyond the New Vehicle Limited Warranty coverage. Up t...

FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY) You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is the only service contractbacked by Ford Motor Company of Canada, Limited. Depending on theplan you purchase, Ford ESP provides benefits such as: • R...

GENERAL MAINTENANCE INFORMATION Why Maintain Your Vehicle? Carefully following this schedule helps protect against major repairexpenses resulting from neglect or inadequate maintenance and may alsohelp to increase the value of your vehicle when you sell or trade it. It is your responsibility to see ...

Chemicals or additives not approved by Ford are not required for factoryrecommended maintenance. In fact, Ford Motor Company recommendsagainst the use of such additive products unless specificallyrecommended by Ford for a particular application. Oils, Fluids and Flushing In many cases, fluid discolo...

Value Shopping for Your Vehicle’s Maintenance Needs Your dealership recognizes the competitive landscape of maintenance andlight repair automotive services. With factory-trained technicians, andone-stop service from routine maintenance like oil changes and tire rotationsto repairs like brake service...

NORMAL SCHEDULED MAINTENANCE AND LOG The following section contains the “Normal Schedule”. This schedule is presented at specific mileage (kilometer) intervals w ith exceptions noted. Miles (x 1,000)* 7.5 15 22.5 30 37.5 45 52.5 60 67.5 75 Kilometers (x 1,000)* 12 24 36 48 60 72 84 96 108 120 Months...

Maintenance Schedule Log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ...

SPECIAL OPERATING CONDITIONS If you operate your vehicle primarily in one of the more demanding conditions listed below, you will need to have some items maintainedmore frequently. If you only occasionally operate your vehicle under these conditions, it is not necessary to perform the additionalmain...

Extensive idling and/or low-speed driving for long distances as in heavy commercial use (i.e. delivery, taxi, patrol car or livery) Inspect frequently,service as required Replace cabin air filter (if equipped) Replace engine air filter Every 5,000 miles(8,000 km) Inspect brake system Inspect wheels ...

Operating in dusty conditions such as unpaved or dusty roads Inspect frequently,service as required Replace cabin air filter (if equipped) Replace engine air filter Every 5,000 miles(8,000 km) Inspect wheels and related components forabnormal noise, wear, looseness or drag Rotate tires*, inspect tir...

Off-road operation Inspect frequently,service as required Inspect steering linkage, ball joints and U-joints;lubricate if equipped with grease fittings Replace cabin air filter (if equipped) Replace engine air filter Every 5,000 miles(8,000 km) Change engine oil and filter Inspect wheels and related...

Special Operating Condition Log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D A...

EXCEPTIONS There are several exceptions to the Normal Schedule. They are listed below: Normal vehicle axle maintenance: Rear axles and power take-off (PTO) units with synthetic fluid and light-duty trucks equipped withFord-design axles are lubricated for life; do not check or change fluidunless a le...

Engines (Certification mark) oil of SM or SN quality, the normal oilchange interval is 5,000 miles (8,000 km).If the available API “SM” or “SN” oils are not available, then the oilchange service interval is 3,000 mile (4,800 km). Edge/MKX AWD only – vehicles operating off-road in sand during high am...

A ABS (see Brakes) .....................245 Accessory delay ..........................90 AdvanceTrac ..............................248 Airbag supplemental restraintsystem ........................173, 177, 179 and child safety seats ............175description ..............173, 177, 179disposal ........

filter, specifications ........330, 358recommendations ...................330refill capacities ........................359specifications ..........................359 Event data recording ....................7 Exhaust fumes ..........................242 F Fail safe cooling ........................33...

P Parental MyKeyprogramming .............................115 Parking brake ............................246 Parts(see Motorcraft 威 parts) ...........358 Pedals (see Power adjustablefoot pedals) .................................94 Power adjustable foot pedals .....94 Power deployable runningboards ......