Ford 2011 Fiesta v.3- User Manual

Protecting the environment We must all play our part inprotecting the environment. Correctvehicle usage and the authorizeddisposal of waste, cleaning andlubrication materials are significantsteps towards this aim. Information in this respect is highlighted in thisguide with the tree symbol. CALIFORN...

Special instructions For your added safety, your vehicle is fitted with sophisticated electroniccontrols. WARNING: Please read the section Airbag Supplemental Restraint System (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions couldresult in ...

Additionally, when you connect to Traffic, Directions andInformation (if equipped, U.S. only) the service uses GPStechnology and advanced vehicle sensors to collect the vehicle’scurrent location, travel direction, and speed (“vehicle travelinformation”) only to help provide you with the directions, ...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Warning lights can alert you to a vehicle condition that may becomeserious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make sure thebul...

WARNING: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possiblycausing a fire. Low fuel: Displays when the fuel level in the fuel tank is at or nearempty (refer to Fuel gaug...

Anti-lock brake system: If the ABS light stays illuminated orcontinues to flash, a malfunction hasbeen detected, have the systemserviced immediately by yourauthorized dealer. Normal braking is still functional unless the brakewarning light also is illuminated. Airbag readiness: If this light fails t...

AdvanceTrac 威 /Traction control (if equipped): Displays when the AdvanceTrac 威 /Traction control is active. If the light remains on, havethe system serviced immediately, refer to the Driving chapter for more information. AdvanceTrac 威 /Traction control off light (if equipped): Illuminates when Advan...

GAUGES Shown in standard measure. Metric similar. 1. Tachometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scalemay damage the engine. Refer to Filling the tank in the Maintenance and Specifications chapter for more info...

mi (km) TRIP — Trip odometer: Registers the mileage of individual journeys. mi (km) TO E — Distance to empty (if equipped): Indicates the approximate distance the vehicle will travel on the fuel remaining in thetank. Changes in driving pattern may cause the value to vary. AVG MPG (l/100km) — Average...

• Chimes: Move right to enter the menu, then up or down to select from warning chimes or info chimes. Press OK to confirm. Clock: Select Clock then move right to enter the menu. Scroll up or down to select from to select from: • Set time: Move right to enter the menu and adjust the time. • Set date:...

AUDIO SYSTEMS AM/FM stereo or AM/FM stereo single CD/MP3 (if equipped) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that maytake their focus off the road. Your ...

• Occupancy mode: Scroll to select Occupancy mode and move right or press OK to enter. Then, scroll to select from Optimize Allor Optimize Driver. Occupancy mode optimizes sound quality forthe chosen seating position. Press OK to confirm your selection. • DSP Equalizer: Scroll to select DSP Equalize...

• SYNC phone (if equipped): Scroll to select Phone Menu and then press OK to enter the menu. Refer to the SYNC 威 section in this chapter for more information. Note: SYNC Phone must be the selected feature to access this menu. • Audio: Scroll to select Audio and then move right to enter the menu. Scr...

The auxiliary input jack (AIJ)provides a way to connect yourportable music player to thein-vehicle audio system. This allowsthe audio from a portable musicplayer to be played through thevehicle speakers with high fidelity.To achieve optimal performance,please observe the followinginstructions when a...

WARNING: Store the portable music player in a secure location, such as the center console or the glove box, when the vehicle is in motion. Hard objects may become projectiles in a collision or suddenstop, which may increase the risk of serious injury. The audioextension cable must be long enough to ...

Radio reception factors: There are three factors that can affect radio reception: • Distance/strength: The further you travel from an FM station, theweaker the signal and the weaker the reception. • Terrain: Hills, mountains, tall buildings, power lines, electric fences,traffic lights and thundersto...

Do not use any irregular shapedCDs or discs with a scratchprotection film attached. CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommended that homemadeCDs be identified withpermanent felt tip marker r...

Sample MP3 structure If you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variousfiles may be present, (files withextensions other than mp3), onlyfiles with the .mp3 extension will beplayed. Other files will be ignoredby the syst...

SYNC 威 . In addition, if you connect a media device, SYNC 威 creates and retains an index of media content supported by SYNC 威 . SYNC 威 also records a short development log of approximately 10 minutes of allrecent SYNC 威 activity. The log profile and other SYNC 威 data may be used to improve SYNC 威 an...

SYNC 姞 voice recognition feature SYNC 威 is equipped with an advanced interactive Voice Recognition (VR) system. This system allows you to perform many operations by“speaking” certain commands to the system. The system will respondwith a series of audible tones, prompts, questions and spokenconfirmat...

If the system has a low confidence level of what was asked, it willprompt you to try again or ask for help. Note: Even with Confirmation prompts turned OFF, you may be asked to confirm certain settings occasionally. Clarification through candidate lists Candidate lists are created when the system ha...

Commands for voice settings In voice settings, you can customize the level of system interaction, helpand feedback. The system default settings include standard interaction aswell as candidate lists and confirmation prompts as all provide the mostguidance and feedback. At any time, while in voice se...

Voice commands in phone mode WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device that may take theirfocus off the road. Your primary responsibility is the safe operation ofthe ve...

While in phone mode, you may also say “Menu” and then any ofthe following commands: • [Phone] settings [message] notification on • [Phone] settings [message] notification off • [Phone] connections • Phone name • Signal • Battery • [Phone] settings [set] phone ringer • [Phone] settings [set] ringer 1...

At any time, you may say these commands: • SYNC • USB • Line in • Bluetooth Audio • Phone • Voice settings • Cancel • Vehicle health report (if equipped, U.S. only) • Help • Services (if equipped, U.S. only) Voice commands when using Traffic, Directions & Informationservices (if equipped, U.S. o...

The first thing you must do to use the system is to ’pair’ your Bluetooth 威 enabled phone with your vehicle’s SYNC 威 system. This process allows your phone to wirelessly communicate with the hands-free SYNC 威 system and ensures that other phones cannot inadvertently do so. Topair your phone for the ...

Note: You can also manually enter the desired number by pressing the presets (0–9). Ending a call At any time, you can end an active phone call by pressing andholding or PHONE. Exiting phone mode When in phone mode but not in an active call, press and hold or PHONE to exit phone mode. Answering an i...

3. When the desired selection appears in the display, press OK. If you choose Reply to Text Message , SYNC 威 will take you back to the text messaging menu and allow you to again cycle through the list ofpredefined messages to send. If you choose Forward Text Message , SYNC 威 will take you to your ca...

Note: SYNC 威 supports a maximum of three callers on a multiparty/conference call. Accessing your call history and phone book during an active call Note: Accessing your phone book is a speed dependent feature. The vehicle must be moving less than 3 mph (5 km/h) to use this feature. You can access you...

Phone redial Phone redial will prompt your cellular phone with Bluetooth wireless technology to redial the last number called (if available). Note: To scroll, press / . 1. Press PHONE to enter Phone Menu . 2. When Phone Redial is selected, press OK. 3. When Redial? appears, press OK. Redialing ѧ wil...

Note: To scroll, press / . 1. Press PHONE to enter Phone Menu . 2. Scroll until Phonebook is selected and press OK. If there are fewer than 255 listings, SYNC 威 will list them alphabetically in flat file mode. If there are more than 255 entries listed, SYNC 威 will organize them into quick select alp...

9. When the system asks if you want to send the message, press OK.SYNC 威 will take you back to your inbox. Note: Each text message sent by SYNC 威 will be followed by the signature: “This message was sent from my __”. The message will sayeither Ford, Lincoln or Mercury, depending on your vehicle. Dow...

4. Once your destination is selected, a route is downloaded to yourvehicle. Turn by Turn Direction features Once directions are downloaded, you can then access other featuressuch as: Next turn, Route status, Route summary, cancel route, updateroute and also voice guidance. To access these features t...

Personalizing Traffic, Directions and Information: Your Traffic, Directions and Information Services can be personalized toprovide quicker access to your most used or favorite information. Youcan save address points such as, ‘work’ or ‘home’. You can also savefavorite information like sports teams o...

911 Assist™ (if equipped) For 911 Assist™ to function properly, the vehicle must havebattery power after the crash, the cell phone must be previouslypaired, connected to SYNC 威 , and continue to function properly with the ability to make and maintain a 911 call initiated bySYNC 威 , and the 911 Assis...

Vehicle health report (if equipped, U.S. only) WARNING: Always follow scheduled maintenance instructions, regularly inspect your vehicle, and seek repair for any damage or problem you suspect. Vehicle Health Reports supplements, but cannotreplace normal maintenance and vehicle inspection. Vehicle He...

2. Scroll until Vehicle Health is selected and press OK. 3. When User Preferences is selected, press OK. 4. When Automatic Reports is selected, press OK. 5. When the desired mile interval is selected (5000, 7500, or 10000),press OK. When the chosen mileage is reached, SYNC 威 will automatically promp...

1. Press PHONE to enter the Phone Menu . 2. Scroll until System Settings is selected and press OK. 3. Scroll until Advanced is selected and press OK. 4. Scroll until Master Reset is selected and press OK. 5. Press OK to confirm when prompted. The display will confirm whenthe reset is complete. SYNC ...

1. Plug the device into the vehicle’s USB port. 2. Press AUX repeatedly until SYNC 威 USB appears in the radio display. 3. Depending on how many digital media files are on your connecteddevice, Indexing may appear in the radio display until indexing is complete. You will then be taken to the Play Men...

4. Scroll until Select Source is selected and press OK. 5. Scroll until Bluetooth Audio is selected and press OK. The display will show the name of the Bluetooth enabled cellular phone currently connected to SYNC 威 . Bluetooth Media Stream will appear in the radio display. While the music is streami...

Repeat: Allows you to repeat any song. Autoplay: Allows you to listen to music which has already been randomly indexed during the indexing process. Note: Depending on the amount of files on your device, SYNC 威 may take awhile to index all the metadata information. 5. When the desired choice is selec...

To access: 1. Press AUX. 2. Press MENU. 3. When MediaPlayer Menu appears in the display, press OK. 4. Use / to cycle through the following options: • Play menu • Select Source • Media Settings • Mobile Apps • System Settings • Exit Menu 5. When Mobile Apps appears in the display, press OK to enter t...

6. When the system asks if you would like to restore the defaults pressOK. The display will then confirm when they are restored. SYNC 威 will take you back to the Advanced menu. Performing a master reset A master reset allows you to completely erase all information stored inSYNC 威 (all phone book, ca...

SYNC 威 is able to organize and sort your indexed media from your playing device by metadata tags. Metadata tags are descriptive softwareidentifiers embedded in your media files which provide information aboutthe media file. SYNC 威 supports the following metadata tags: • Artist • Album • Genre • Trac...

Note: With certain playing devices, if your metadata tags (Artist, Album, Track, Genre) are not populated, the tracks won’t be available in voicerecognition, the Play Menu or Similar Music . However, if you place these tracks with unpopulated metadata tags onto your playing device in“Mass Storage De...

the recipient agrees to the terms of this EULA. If the SOFTWARE isan upgrade, any transfer must include all prior versions of theSOFTWARE. • Termination: Without prejudice to any other rights, FORD MOTOR COMPANY or MS may terminate this EULA if you fail to comply withthe terms and conditions of this...

• Additional Software/Services: The SOFTWARE may permit FORD MOTOR COMPANY, third party software and service suppliers, MS,Microsoft Corporation, their affiliates and/or their designated agent toprovide or make available to you SOFTWARE updates, supplements,add-on components, or Internet-based servi...

PRODUCT SUPPORT: Product support for the SOFTWARE is not provided by MS, its parent corporation Microsoft Corporation, or theiraffiliates or subsidiaries. For product support, please refer to FORDMOTOR COMPANY instructions provided in the documentation for theDEVICE. Should you have any questions co...

WARNING: Operating certain parts of this system while driving can distract your attention away from the road, and possibly cause an accident or other serious consequences. Do not changesystem settings or enter data non-verbally (using your hands) whiledriving. Stop the vehicle in a safe and legal ma...

MANUAL HEATING AND AIR CONDITIONING SYSTEM Manual system with A/C shown; heater only system similar. 1. : Turn to select the desired fan speed. 2. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control setting: MAX A/C (if...

: Distributes outside air through the windshield defroster and demister vents. Can be used to clear thin ice or fog from thewindshield. The system will automatically provide outside air to reducewindow fogging. To exit select another mode. 3. Temperature: Controls the temperature of the airflow in t...

and put the vehicle’s transmission into the P (Park) gear position(automatic transmission only) to continue to receive cool air from yourA/C system. For maximum cooling performance in MAX A/C mode: 1. Select MAX A/C. 2. Select the coolest temperature setting. 3. Set the fan to the highest speed init...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the low beam headlamps on. High beams Pull the lever fully past the detentto activate. Pull the lever fully againto deactivate. Flash-to-pass Pull the lever toward you s...

Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the ignition must be in the on position and • the headlamp control is in the off or parking lamp position. WARNING: Always remember to turn on your headlamps at dusk or during inclement weather. Th...

TURN SIGNAL CONTROL • Push down to activate the leftturn signal. • Push up to activate the right turnsignal. When changing lanes, the turn signal indicator can be programmed toflash either one or three times when the stalk is tapped. See Multifunction display in the Instrument cluster section for mo...

BULB REPLACEMENT Lamp assembly condensation Exterior lamps are vented to accommodate normal changes in pressure.Condensation can be a natural by-product of this design. When moist airenters the lamp assembly through the vents, there is a possibility thatcondensation can occur when the temperature is...

Function Number of bulbs Trade number 4-door rear deck lamp(backup) 1 921 5-door rear lamp(stop/reverse) 2 3157K 5-door rear lamp(turn) 1 3157A (amber) License plate lamp 1 W5W * High-mount brakelamp 1 LED Interior lamp 1 W6W Reading lamp 1 W5W Luggage compartmentlamp 1 W5W To replace all instrument...

Replacing the rear stop lamp (5-door) 1. Turn the bulb holdercounterclockwise and remove it. 2. Remove the bulb from the holder. 3. Reverse the procedure to install the new bulb. Replacing the reverse signal rear lamp (5-door) 1. Turn the bulb holdercounterclockwise and remove it. Lights 117 2011 Fi...

WINDSHIELD WIPERS Move the lever down for a singlewipe. For intermittent operation, move control up one position andadjust the rotary control to thedesired speed. For normal operation, move control up two positions and up three positions for high-speed wiping. Windshield washer To activate the winds...

Press and pull the window switchesto open and close windows. • Press down (to the first detent)and hold the switch to open. • Pull up (to the first detent) andhold the switch to close. Rear Window Buffeting: When one or both of the rear windows are open, the vehicle may demonstrate a wind throb or b...

3. If the window does not close after the third attempt, contact yourauthorized dealer as soon as possible. Resetting the bounce-back feature WARNING: The bounce-back function is deactivated until you have reset the memory. After the battery has been disconnected from the vehicle you must resetthe b...

Automatic dimming interior rear view mirror (if equipped) The interior rear view mirror has an auto-dimming function. Theelectronic day/night mirror will change from the normal (high reflective)state to the non-glare (darkened) state when bright lights (glare) reachthe mirror. When the mirror detect...

Heated outside mirrors (if equipped) Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated. Do not remove ice from themirrors with a scraper orattempt to readjust the mirrorglass if it is frozen in place.These actions could cause damage to the glass...

Using speed controls The speed controls are located on the steering wheel. The followingbuttons work with speed control: SET+: Press to set a speed or to increase a set speed. CAN (Cancel)/RES (Resume): Press to cancel or resume a setspeed. SET–: Press to decrease a set speed. OFF: Press to turn spe...

M (Mode): Press repeatedly to scroll through available audio modes. For further information on the SYNC 威 system, refer to the SYNC 威 supplement. MOON ROOF (IF EQUIPPED) The moon roof control is located on the overhead console. WARNING: Do not let children play with the moon roof or leave children u...

POSITIVE RETENTION FLOOR MAT WARNING: Do not install additional floor mats on top of the factory installed floor mats as they may interfere with the accelerator or the brake pedals. Position the floor mat so that theeyelets are over the retention postsand press down to lock in. Makesure that the mat...

KEYS Integrated keyhead transmitters (IKTs) (If equipped) Your vehicle may be equipped withtwo integrated keyhead transmitters(IKTs). The key blade starts thevehicle and unlocks/locks all thedoors. The transmitter portionfunctions as the remote entrytransmitter. Your IKTs are programmed to yourvehic...

The IA key also contains aremovable mechanical key bladethat can be used to unlock thedriver door. To release themechanical key blade, press therelease buttons on the edge of thetransmitter and remove the keyblade. Your IA keys are programmed toyour vehicle. You cannot enter orstart your vehicle wit...

If both front doors are closed, the vehicle can be locked by any method,regardless of whether the key is in the ignition or not. Smart locks for intelligent access keys (IA key) (if equipped) This feature is intended to prevent you from unintentionally locking yourIA key inside your vehicle. If your...

• the ignition is on, • you shift into any gear putting the vehicle in motion, and • the vehicle attains a speed greater than 12 mph (20 km/h). If a door(s) is unlocked, the autolock feature will repeat when: • the vehicle slows below 12 mph (20 km/h) and then attains a speedgreater than 12 mph (20 ...

• To program the autounlock feature, press the power door lock controlfor less than 1 second and release. Each short press of the power door lock control toggles the state of the autounlocking featurebetween enabled and disabled. A chime sounds when the feature isenabled or disabled. 7. Turn the ign...

• arm and disarm the perimeter anti-theft system. • operate the illuminated entry feature. The remote entry lock/unlock feature operates in any ignition positionexcept when the engine is running and vehicle speed is more than 4 mph(7 km/h). If there are problems with the remote entry system, make su...

may be necessary to mechanically unlock your door. The mechanical keyblade in your IA key can be used to open the driver’s door in thissituation (refer to Intelligent access key in this chapter for more information on the location and use of the mechanical key blade).A mechanical key is needed for a...

3. Twist a flat object in the positionshown to separate the two halves ofthe transmitter. 4. Carefully insert a flat object inthe position show to open thetransmitter. 5. Carefully pry out the batter with a flat object. Note: Please refer to local regulations when disposing of transmitter batteries....

Please read and understand the entire procedure before you begin. To reprogram the remote entry transmitters: 1. Insert the first programmed key into the ignition and turn the keyfrom off to run (maintain the key in run for approximately 3 seconds).2. Turn the first key to off and remove it from the...

Replacing coded keys can be very costly. Store an extra programmed keyaway from the vehicle in a safe place to help prevent anyinconveniences. Please visit an authorized dealer to purchase additionalspare or replacement keys. PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter anti-theft system will ...

3. Lower the head restraint by pressing and holding the guide sleeveadjust release button (3) and pushing down on the head restraint (1). Properly adjust the head restraint so that the top of the head restraint iseven with the top of your head and positioned as close as possible to theback of your h...

To operate the heated seats: • Press the button located on theinstrument panel to activate. • Press again to deactivate. The heated seats will activate when the ignition is in the on position andthe engine is running. REAR SEATS Second row head restraints Your vehicle is equipped with rear seat outb...

WARNING: Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. Make sure that the safety belt is not laying on theseat latch. After returning the seatback to its original position, pull onthe seatback to ensure that it has fu...

WARNING: Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, movethe seat all the way back. WARNING: Always transport children 12 years old and under in a rear seating ...

Front outboard safety belt energy management retractors The front safety belt energy management retractors allow webbing to bepulled out of the retractor in a gradual and controlled manner inresponse to the occupant’s forward momentum. This helps reduce therisk of force-related injuries to the occup...

Combination lap and shoulder belts The front outboard and rear safety restraints in the vehicle arecombination lap and shoulder belts. 1. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) until you hear a snap and feelit latch. Make sure the t...

Pregnant women should alwayswear their safety belt. The lap beltportion of a combination lap andshoulder belt should be positionedlow across the hips below the bellyand worn as tight as comfort willallow. The shoulder belt should bepositioned to cross the middle ofthe shoulder and the center of thec...

How to use the automatic locking mode 1. Buckle the combination lap andshoulder belt. 2. Grasp the shoulder portion andpull downward until the entire beltis pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the auto...

Use only extensions manufactured by the same supplier as the safetybelt. Manufacturer identification is located at the end of the webbing onthe label. Also, use the safety belt extension only if the safety belt is tooshort for you when fully extended. WARNING: Do not use extensions to change the fit...

Conditions of operation If... Then... The driver’s safety belt is notbuckled before the ignitionswitch is turned to the onposition... The safety belt warning lightilluminates 1-2 minutes and thewarning chime sounds 4-8 seconds. The driver’s safety belt isbuckled while the indicatorlight is illuminat...

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... “Crashes are rare events” 36700 crashes occur every day. The more we drive, the more we areexposed to “rare” events, even forgood drivers. 1 in 4 of us will be ser...

Children and airbags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating position. Failure to followthese instructions may increase therisk of injury in a collision. WARNING: Airb...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

WARNING: To reduce the risk of possible serious injury: Do not stow objects in seat back map pocket (if equipped) or hang objects off seat back if a child is in the front passenger seat.Do not place objects underneath the front passenger seat or betweenthe seat and the center console (if equipped).C...

provided to occupants in side impact collisions. The seat-mounted sideairbag was designed to inflate between the door panel and occupant tofurther enhance the protection provided occupants in side impactcollisions. The side air curtain system SRS is designed to activate when the vehiclesustains late...

• The readiness light will not illuminate immediately after ignition isturned on. • A series of five beeps will be heard. The tone pattern will repeatperiodically until the problem and/or light are repaired. If any of these things happen, even intermittently, have the SRS servicedat your authorized ...

WARNING: All children are shaped differently. The Recommendations for Safety Restraints are based on probable child height, age and weight thresholds from NHTSA and other safetyorganizations or are the minimum requirements of law. Fordrecommends checking with a NHTSA Certified Child Passenger Safety...

Recommendations for attaching child safety restraints for children RestraintType Child Weight Use any attachment method as indicated below by “X” LATCH(loweranchorsandtoptetheranchor) LATCH(loweranchorsonly) Safetybeltandtoptetheranchor Safetybelt andLATCH(loweranchorsand toptetheranchor) Safetybelt...

WARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision, which may result in serious injury ordeath. WARNING: Never use pillows, books, or towels to boost a child. They can slide around and increase ...

Follow all the safety restraint and airbag precautions that apply to adultpassengers in your vehicle. If the child is the proper height, age, and weight (as specified by yourchild safety seat or booster manufacturer), fits the restraint and can berestrained properly, then restrain the child in the c...

4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear a snap and feel the latchengage. Make sure the tongue islatched securely by pulling on it. 5. To put the retractor in theautomatic locking mode, grasp...

Use of inboard lower anchors from the outboard seating positions(center seating use) The lower anchors at the center of the second row rear seat are spaced390 mm (15 inches) apart. The standardized spacing for LATCH loweranchors is 280 mm (11 inches) center to center. A child seat with rigidLATCH at...

2. Locate the correct anchor for theselected seating position. 3. Clip the tether strap to theanchor as shown. If the tether strap is clippedincorrectly, the child safety seat maynot be retained properly in theevent of a collision. 4. Tighten the child safety seat tether strap according to themanufa...

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, and lets you adjust the shoulder belt to cross the chest andrest snugly near the center of the shoulder. The drawings below comparethe ideal fit (cente...

Follow all instructions provided by the manufacturer of the booster seat. WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the riskof injury or death in a collis...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING Tire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperature A These Tire Quality G...

WARNING: Under-inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or “blowout”, with unexpected loss of vehicle control and increasedrisk of injury. Under-inflation increases sidewall flexing and rollingresistance, resulting in heat buildup a...

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, ...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

WARNING: When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautionslisted below. If the beads do not seat at the maximum pressureindicated, re-lubricate and try again.When inflating the ...

• Do not run over curbs or hit the tire against a curb when parking WARNING: If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to fiveseconds. WARNING: Do not spin th...

• Front-wheel drive (FWD) vehicles(front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanicalproblem involved before t...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on aspecified government test course. For example, a tire graded 150would wear one and one-half (1 1 ⁄ 2 ) times as well ...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below. Note: Tire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the Tire a...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Grades donot apply ...

The tire pressure monitoring system complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that...

Understanding your tire pressure monitoring system (TPMS) The tire pressure monitoring system measures pressure in your four roadtires and sends the tire pressure readings to your vehicle. The low tirepressure warning light will turn on if the tire pressure is significantly low.Once the light is ill...

When you believe your system is not operating properly The main function of the tire pressure monitoring system is to warn youwhen your tires need air. It can also warn you in the event the system is nolonger capable of functioning as intended. Please refer to the followingchart for information conc...

When inflating your tires When putting air into your tires (such as at a gas station or in yourgarage), the tire pressure monitoring system may not respondimmediately to the air added to your tires. It may take up to two minutes of driving over 20 mph (32 km/h) for thelight to turn off after you hav...

If you choose to install snow tires on your vehicle, they must be thesame size, construction, and load range as the original tires listed on thetire placard, and they must be installed on all four wheels. Mixing tires ofdifferent size or construction on your vehicle can adversely affect yourvehicle’...

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-Pillar or the edge of the driver’s door(vehicles exported outside the US and Canada may not have a TireLabel). Look for “THE COMBINED WEI...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. Tires, Wheels and Loading 223 2011 Fiesta (fie) ...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

WARNING: Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tireswith a higher limit than the original tires do not increase the GVWRand GAWR limitations. WARNING: Exceeding any vehicle ...

• A final example for your vehicle with 1400 lb. (635 kg) of cargo andluggage capacity. You and one of your friends decide to pick upcement from the local home improvement store to finish that patioyou have been planning for the past 2 years. Measuring the inside ofthe vehicle with the rear seat fol...

Before you tow your vehicle, follow these directions for your specificvehicle configuration after it is hooked-up to the RV or tow dolly: Vehicles with a manual transmission: 1. Release the parking brake. 2. Move the gearshift to the neutral position. 3. The maximum towing speed is 70 mph (113 km/h)...

STARTING Positions of the ignition If your vehicle is equipped with a push button start system, refer to Push button start system in this section for ignition modes. 1. 0 (off) — locks the steeringwheel, automatic transmissiongearshift lever and allows keyremoval. This position also shuts theengine ...

• Make sure the gearshift is in P(Park). If starting a vehicle with a manualtransmission: • Make sure the parking brake isset. • Press the clutch pedal to thefloor. 3. Turn the key to II (on) withoutturning the key to III (start). Some warning lights will briefly illuminate. See Warning lights and c...

1. Turn the key to II (on) withoutturning the key to III (start). 2. Turn the key to III (start), thenrelease the key as soon as theengine begins cranking. Your vehiclehas a computer assisted crankingsystem that assists in starting theengine. After releasing the key fromthe III (start) position, the...

2. On — press the START/STOP button without applying the brake pedal(automatic transmission) or clutch pedal (manual transmission). This willpower your vehicle’s electrical system and the warning lights in theinstrument cluster will illuminate, but the engine will remain off. 3. Start — press the ST...

Fast restart feature: The fast restart feature allows you to re-start your vehicle within 10 seconds of switching the vehicle off, if a valid IAkey is not present when the vehicle is switched off. You can re-start thevehicle (by applying the brake/clutch pedal and pressing theSTART/STOP button) for ...

Important ventilating information If the engine is idling while the vehicle is stopped for a long period oftime, open the windows at least 1 inch (2.5 cm) or adjust the heating orair conditioning to bring in fresh air. ENGINE BLOCK HEATER (IF EQUIPPED) An engine block heater warms the engine coolant...

Electronic stability control (ESC) Electronic stability control (ESC) may enhance your vehicle’s directionalstability during adverse maneuvers, for example when cornering severelyor avoiding objects in the roadway. ESC operates by applying brakes toone or more of the wheels individually and, if nece...

In R (Reverse), ABS and the engine and brake traction control featureswill continue to function; however, ESC is disabled. AdvanceTrac 威 Features TCS switch inmulti-functiondisplay Stability control light Stability control off light ESC TCS Default at start-up Illuminated during bulb check Illuminat...

WARNING: The EPS has diagnostics checks that continuously monitor the EPS to ensure proper operation of the electronic system. When an electronic error is detected, the message POWERSTEERING ASSIST FAULT will be displayed in the message center. Ifthis happens, stop the vehicle in a safe place and tu...

AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED) Understanding the gearshift positions of the 6–speed automatictransmission (if equipped) P (Park) This position locks the transmissionand prevents the front wheels fromturning. To put your vehicle in gear: • Press the brake pedal. • Move the gearshift l...

To return to D (Drive), press the transmission control switch again. • The grade assist lamp in the instrument cluster will not be illuminated. • The transmission will operate in gears one through five. L (Low) This position: • Provides maximum engine braking. • Will downshift to the lowest availabl...

Activating HSA 1. Press the brake pedal to bring the vehicle to a complete standstill.Keep the brake pedal pressed. 2. If the sensors detect that the vehicle is on a slope, the HSA systemwill be activated automatically in D (Drive) uphill or R (Reverse)downhill. 3. When you remove your foot from the...

MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Using the clutch Manual transmission vehicles have a starter interlock that preventscranking the engine unless the clutch pedal is fully pressed. To start the vehicle: 1. Make sure the parking brake is fully set. 2. Press the clutch pedal to thefloor, then...

Recommended shift speeds Do not downshift into 1 (First) when your vehicle is movingfaster than 15 mph (24 km/h). This will damage the clutch. Upshift according to the following chart: Recommended upshifts (for best fuel economy) when accelerating 5-speed manual transmission Shift from: 1 - 2 14 mph...

BLIND SPOT MIRRORS Blind spot mirrors have an integrated convex spotter mirror built intothe upper outboard corner of the outside mirrors. They are designed toassist the driver by increasing visibility along the side of the vehicle. Formore information on your side view mirrors, refer to Exterior mi...

DRIVING THROUGH WATER If driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive throughwater that is higher than the bottomof the wheel rims (for cars) or thebottom of the hubs (for trucks). When driving through water, traction or ...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24-hours, seven days a week • for the...

Canadian customers refer to your Warranty Guide or visit ourwebsite at www.ford.ca for information on: Using roadside assistance Complete the roadside assistance identification card and place it in yourwallet for quick reference. In the United States, this card is found in theOwner Guide portfolio i...

Should your vehicle shut off after a collision due to this feature, you mayrestart your vehicle by doing the following: 1. Turn the ignition switch to the off position. 2. Turn the ignition switch to the on position. In some instances the vehicle may not restart the first time you try torestart and ...

COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 20A Yellow Yellow Yellow Blue Blue 25A Natural Natural — Natural Natural 30A Green Green Green Pink Pink 40A — — Orange Green Green 50A — — Red Red Red 60A — — Blue Yellow Yellow 70A — — Tan — Brown 80A —...

To remove a fuse, use the fuse puller tool provided on the inside of thepassenger compartment fuse panel cover. The high-current fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Protected circuits F1 40A* Anti-lock brake system (ABS)pump F2 50A* Transmission control module(TCM) F3 40A...

Have a flat serviced by an authorized dealer in order to prevent damageto the TPMS sensors, refer to Tire pressure monitoring system (TPMS) in the Tires, Wheels and Loading chapter. Replace the spare tire with a road tire as soon as possible. During repairing or replacing ofthe flat tire, have the a...

• Tow a trailer • Use snow chains on the end of the vehicle with the dissimilar sparetire • Use more than one dissimilar spare tire at a time • Use commercial car washing equipment • Try to repair the dissimilar spare tire Use of one of the dissimilar spare tires listed above at any one wheellocatio...

5. Position the jack in the indentionson the sill next to the tire you arechanging. Turn the jack handleclockwise until the tire is off theground. 6. Remove the lug nuts with the lug wrench. 7. Replace the flat tire with the spare tire, making sure the valve stem isfacing outward. Reinstall the lug ...

WARNING: When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum orbrake disc that contacts the wheel. Ensure that any fasteners thatattach the rotor to the hub are secured so they do ...

1. Connect the positive (+) jumpercable to the positive (+) terminal ofthe discharged battery. 2. Connect the other end of thepositive (+) cable to the positive(+) terminal of the assisting battery. 3. Connect the negative (-) cable tothe negative (-) terminal of theassisting battery. 4. Make the fi...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery. 1. Remove the jumper cable fromthe ground metal surface. 2. Remove the jumper cable on thenega...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift anddollies or flatbed equipment. Do not tow w...

If the vehicle is towed by other means or incorrectly, vehicledamage may occur. Ford Motor Company produces a towing manual for all authorized towtruck operators. Have your tow truck operator refer to this manual forproper hook-up and towing procedures for your vehicle. Emergency towing In case of a...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizeddealer. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfaction. Plea...

In Canada: Mailing address (Ford vehicles) Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Mailing address (Lincoln vehicles) Lincoln CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oak...

You can get more information by calling BBB AUTO LINE at1-800-955-5100, or writing to: BBB AUTO LINE4200 Wilson Boulevard, Suite 800Arlington, Virginia 22203–1833 BBB AUTO LINE applications can also be requested by calling the FordMotor Company Customer Relationship Center at 1-800-392-3673. Note: F...

GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country, contact theappropriate foreign embassy or consulate. These officials can inform youof local vehicle registration regulations and where to find unleaded fuel. If you cannot find unleaded fuel or can onl...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft 威 Detail Wash (ZC-3-A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can ...

• Do not allow paint sealant to come in contact with any non-body(low-gloss black) colored trim, such as grained door handles, roofracks, bumpers, side moldings, mirror housings or the windshield cowlarea. The paint sealant will “gray” or stain the parts over time. PAINT CHIPS Your authorized dealer...

WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, substances on thevehicle’s glass or the wiper blades may be the cause. These may includehot wax treatments used by commercial car washes, water repellen...

Regular cleaning and conditioning will maintain the appearance of theleather. Cleaning For dirt, use a vacuum cleaner then use a clean, damp cloth or softbrush. For routine cleaning, wipe the surface with a soft, damp cloth. For morethorough cleaning, wipe the surface with a mild soap and water solu...

FORD AND LINCOLN CAR CARE PRODUCTS Your Ford or Lincoln authorized dealer has many quality productsavailable to clean your vehicle and protect its finishes. These qualityproducts have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement the style andap...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide to find out wh...

WARNING: To reduce the risk of vehicle damage and/or personal burn injuries, do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under theinstrument panel. 2. Raise the hoo...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 1. Engine coolant reservoir 2. Engine oil filler cap 3. Battery 4. Brake/Clutch fluid reservoir 5. Power distribution box 6. Windshield washer fluid reservoir 7. Air filter assembly 8. Engine oil dipstick 8 7 6 5 1 2 3 4 Maintenance and Specifications...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specifications. Do not use anyspecial washer fluid such aswindshield water repellent type fluidor bug wash. They may causesque...

To replace the wiper blades: 1. Pull the wiper arm away from thewindshield. 2. Press the locking button (1). 3. Remove the wiper blade (2). Note: Make sure the wiper blade locks into place. ENGINE OIL Checking the engine oil Refer to the scheduled maintenance information for the appropriate interval...

2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler capand use a funnel to pour the engine oil into the opening. 3. Recheck the engine oil level. Make sure the oil level is not above theMAX mark on the eng...

Change your engine oil and filter according to the appropriate schedulelisted in the scheduled maintenance information. Ford production and Motorcraft 威 replacement oil filters are designed for added engine protection and long life. If a replacement oil filter is usedthat does not meet Ford material...

WARNING: When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle orbattery. Lift the battery with a battery carrier or with your hands onopposite corners. WARNING: Keep batteri...

When the battery is disconnected or a new battery installed, theautomatic transmission must relearn its adaptive strategy. As a result ofthis, the transmission may shift firmly when first driven. This operation isconsidered normal and will fully update transmission operation to itsoptimum shift feel...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the FULL COLD level, or within theCOLD FILL or MIN / MAX range as listed on the engine coolantreservoir (depending upon application). • Refer to scheduled maintenance information for serv...

• DO NOT MIX different colors or types of coolant in your vehicle. Make sure the correct coolant is used. DO NOT MIX recycled coolant and new (unused) coolant together in the vehicle. Mixing of enginecoolants may harm your engine’s cooling system. The use of animproper coolant may harm engine and co...

4. When you are sure that all the pressure has been released, use thecloth to turn it counterclockwise and remove the cap. 5. Fill the coolant reservoir slowly with the proper coolant mixture, towithin the COLD FILL RANGE or the FULL COLD level on the reservoir.If you removed the radiator cap in an ...

Refueling WARNING: Fuel vapor burns violently and a fuel fire can cause severe injuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; ...

4. After you are done pumping fuel, slowly remove the fuel fillernozzle—allow about five seconds after pumping fuel before removing thefuel filler nozzle. This allows residual fuel to drain back into the fuel tankand not spill onto the vehicle. Note: A fuel spillage concern may occur if overfilling ...

Octane recommendations Your vehicle is designed to use“Regular” unleaded gasoline with apump (R+M)/2 octane rating of 87.Some stations offer fuels posted as“Regular” with an octane ratingbelow 87, particularly in high altitude areas. Fuels with octane levelsbelow 87 are not recommended. Do not be co...

• Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers). 2. Each time you fill the tank, record ...

EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and acatalytic converter which will enable your vehicle to comply withapplicable exhaust emission standards. To make sure that the catalyticconverter and other emission control components continue to workproper...

The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the MIN andMAX lines are within the normaloperating range; there is no need toadd fluid. If the fluid levels areoutside of the normal operatingrange, the performance of the sy...

AIR FILTER Refer to scheduled maintenance information for the appropriate intervals for changing the air filter element. When changing the air filter element, use only the air filter elementlisted. Refer to Motorcraft 威 part numbers in this chapter. WARNING: To reduce the risk of vehicle damage and/...

Cooling system • Protect against freezing temperatures. • When removing vehicle from storage, check coolant fluid level.Confirm there are no cooling system leaks, and fluid is at therecommended level. Battery • Check and recharge as necessary. Keep connections clean. • If storing your vehicle for mo...

• If the battery was removed, clean the battery cable ends and inspect. If you have any concerns or issues, contact your authorized dealer. MOTORCRAFT 姞 PART NUMBERS Component 1.6L engine Air filter element FA-1904 Oil filter FL-910S 1 Battery BXT-96R-500 Spark plugs 2 1 Only use the specified repla...

TRANSMISSION CODE DESIGNATIONS You can find a transmission code onthe Safety Compliance CertificationLabel. The following table tells youwhich transmission each coderepresents. Description Code Five-speed manual transmission C Six-speed automatic transmission A Maintenance and Specifications 326 201...

FORD CUSTOM ACCESSORIES FOR YOUR VEHICLE A wide selection of Ford Custom Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement the ...

Peace of mind • Keyless entry keypad • Seat covers* • Remote start • Windshield wiper shaker* • Wheel locks • Vehicle tracking and recovery* • Back-up camera* • Bumper mounted parking sensors* *Ford Licensed Accessories (FLA) are warranted by the accessorymanufacturer’s warranty. Ford Licensed Acces...

FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY) More than 30 million Ford and Lincoln owners have discovered thepowerful protection of Ford ESP. It is the only extended service planbacked by Ford Motor Company, and provides “peace of mind”protection beyond the New Vehicle Limited Warranty coverage. Up t...

FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY) You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is the only service contractbacked by Ford Motor Company of Canada, Limited. Depending on theplan you purchase, Ford ESP provides benefits such as: • R...

Ford strongly recommends the use of genuine Ford replacement parts.Parts other than Ford, Motorcraft 威 or Ford-authorized remanufactured parts that are used for maintenance replacement or for the service ofcomponents affecting emission control must be equivalent to genuineFord Motor Company parts in...

Genuine Ford and Motorcraft 姞 replacement parts Dealerships stock Ford and Motorcraft 威 branded replacement parts. These parts meet or exceed Ford Motor Company’s specifications, andwe stand behind them. Parts installed at your dealership carry anationwide, 12 month/12,000 mile (20,000 km) parts and...

NORMAL SCHEDULED MAINTENANCE AND LOG The following section contains the “Normal Schedule”. This schedule ispresented at specific mileage (kilometer) intervals with exceptionsnoted. Reset your oil life monitoring system after each engine oil andfilter change; refer to the Instrument Cluster chapter. ...

Miles (x 1,000) 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 Kilometers (x 1,000) 16 32 48 64 80 96 112 128 144 160 176 192 208 224 240 Months 12 24 36 48 60 72 84 96 108 120 132 144 156 168 180 Change engine oil and filter • ••••• ••••••••• Rotate tires, inspect tire wear and measure tread de...

Every 20,000 miles(32,000 km) Replace cabin air filter (if equipped) Every 30,000 miles(48,000 km) Replace climate-controlled seat filter (ifequipped) Replace engine air filter Every 100,000 miles(160,000 km) Change engine coolant 1 Replace spark plugs Inspect accessory drive belt(s) 2 Every 150,000...

Maintenance schedule log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ...

SPECIAL OPERATING CONDITIONS If you operate your vehicle primarily in one of the more demanding conditions listed below, you will need to have some items maintainedmore frequently. If you only occasionally operate your vehicle under these conditions, it is not necessary to perform the additionalmain...

Operating in dusty conditions such as unpaved or dusty roads Inspect frequently, service as required – Replace cabin air filter (if equipped) – Replace engine air filter Every 5,000 miles (8,000 km) – Inspect the wheels and related components forabnormal noise, wear, looseness or drag– Rotate tires,...

Special operating condition log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D A...

EXCEPTIONS In addition, there are several exceptions to the Normal Schedule. Theyare listed below: Normal vehicle axle maintenance ❑ Rear axles and power take-off (PTO) units containing synthetic fluid and light duty trucks equipped with Ford-design axlesare lubricated for life. These fluids are not...

ENGINE COOLANT CHANGE RECORD Initial change 6 years or 100,000 miles (160,000 km)(whichever comes first) After initial change Every 3 years or 50,000 miles (80,000 km) Engine coolant change log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE...

911 Assist™ ................................65 A Accessing and using your USBport ..............................................79 Accessing call history/phonebook during active call ...............54 Accessing system settings .........83 Accessing vehicle applications ..82 Accessing your phone book...

automatic dimming rearviewmirror ......................................126heated ......................................127side view mirrors (power) .....126signal .......................................127 Modifying your phone book .......60 Moon roof ..................................130 Motorcraft...