Ford 2011 Explorer v.3- User Manual

Warning symbols on your vehicle When you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempting adjustmentof any kind. Protecting the environment We must all play our part inprotecting the environment. Correctvehicle usage and the authorizedd...

DATA RECORDING Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, st...

CELL PHONE USE The use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,drivers must not compromise their own or others’ safety when usingsuch equipment. Mobile Communications can enhance personal safetyand security when app...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid -Non-Petroleum Based P...

WARNING LIGHTS AND CHIMES Base instrument cluster with standard measure shown; metricsimilar Optional instrument cluster with standard measure shown; metricsimilar Warning lights can alert you to a vehicle condition that may becomeserious enough to cause extensive repairs. A warning light mayillumin...

Brake system warning light: To confirm the brake system warninglight is functional, it willmomentarily illuminate when theignition is turned to the on positionwhen the engine is not running, or in a position between on and start, orby applying the parking brake when the ignition is turned to the onp...

Liftgate ajar (RTT): Displays when the ignition is in the onposition and the trunk is open. Low washer fluid (RTT): Illuminates when the windshieldwasher fluid is low. Turn signal: Illuminates when the left or right turn signal or thehazard lights are turned on. If theindicators flash faster, check ...

Hill descent (RTT) (ifequipped): Illuminates when hill descent is turned on. Heads up display (if equipped): A red beam of lights will illuminateon the windshield in certaininstances when using adaptivecruise control and/or the collisionwarning system. It will alsoilluminate momentarily when you sta...

GAUGES Base clusterShown in standard measure. Metric similar. 1. Tachometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scalemay damage the engine. 3 2 4 5 4 3 2 1 0 7 F E 6 km/h 80 60 40 20 0 20 0 40 60 80 100 120 140 16...

2. Multifunction display: This displays the engine coolant temperature, 4WD gauge, odometer/trip meter and other vehicle features. This is alsoused to configure different vehicle personalization options and displaythe status of various vehicle functions. See Standard message center in this chapter f...

Optional clusterShown in standard measure. Metric similar. 1. Multifunction display: This displays the fuel gauge, tachometer, engine coolant temperature, odometer/trip meter and other vehiclefeatures. This is also used to configure different vehicle personalizationoptions and display the status of ...

Main menu Scroll up/down to highlight one of the options, then press the right arrowkey or OK to enter into that menu option. Press the left arrow key asneeded to exit back to the main menu. *Trip 1 or 2 Trip Odometer – shows the accumulated trip distance. Trip Timer – shows the elapsed trip time. T...

Menu Control: You can choose a different menu control operation tosuite your needs. In any screenwhich shows these category icons(other than the Main menu screen)and: • Standard is set– then scrolling up and down will scroll through themain categories. • Memory on is set– then scrolling up and down ...

Standard trip display • Trip distance — shows the accumulated trip distance • Elapsed trip time — timer stops when the vehicle is turned off andrestarts when the vehicle is restarted. Enhanced trip display • Trip distance — shows the accumulated trip distance • Average fuel economy — shows the avera...

2. Record the highway fuel economy for future reference. It is important to reset fuel economy after setting the speed control toget accurate highway fuel economy readings. For more information refer to Essentials of good fuel economy in the Maintenance and Specifications chapter. Settings/Vehicle S...

Units Distance Miles & Gal / Km & Liters Temperature Fahrenheit (°F) / Celsius (°C) Restore defaults Hold OK to Restore Settings to Factory Defaults Information In this mode, you can view different vehicle system information andperform a system check.When Press OK for info is displayed, pres...

System warnings and status messages See System warning and status messages later in this chapter for more information. SYSTEM WARNINGS AND STATUS MESSAGES System warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems. Note: Depending on the vehicle options equippe...

Battery and Charging System Messages Action / Description TRANSPORT MODECONTACT DEALER Contact your authorized dealer as soon aspossible. FACTORY MODECONTACT DEALER Contact your authorized dealer as soon aspossible. LOW BATTERYFEATURESTEMPORARILYTURNED OFF Displayed when the battery managementsystem...

Maintenance Messages Action / Description LOW ENGINE OILPRESSURE Stop the vehicle as soon as safely possible,turn off the engine. Check the oil level. See Checking the engine oil in the Maintenance and Specifications chapter. If the warning stays on or continues to come on with yourengine running, c...

Tire Messages Action / Description LOW TIREPRESSURE Displayed when one or more tires on yourvehicle have low tire pressure. Refer to Inflating Your Tires in the Tires, Wheels and Loading chapter. TIRE PRESSUREMONITOR FAULT Displayed when the Tire Pressure MonitoringSystem is malfunctioning. If the w...

MYFORD™ SYSTEM (IF EQUIPPED) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that maytake their focus off the road. Your primary responsibility is the safeoperatio...

Auxiliary input jack (line in) WARNING: Driving while distracted can result in loss of vehicle control, accident and injury. Ford strongly recommends that drivers use extreme caution when using any device or feature that maytake their focus off the road. Your primary responsibility is the safeoperat...

SINGLE ZONE MANUAL SYSTEM WITH REAR CLIMATECONTROLS (IF EQUIPPED) Temperature conversion: To switch between Fahrenheit and Celsius: Press MENU > Display Settings > Temp. Setting, or refer to Settings in the Message Center section of the Instrument Cluster chapter. 1. (Fan speed adjustment): Tu...

• : Distributes air through the instrument panel vents. • : Distributes air through the instrument panel vents, demister vents, floor vents and rear seat floor vents. • : Distributes air through the demister vents, floor vents and rear seat floor vents. 6. A/C: Press to activate/deactivate air condi...

Operating tips • To reduce fog build-up on the windshield during humid weather,select (defrost) or (floor/defrost). • To reduce humidity build-up inside the vehicle, do not drive with thesystem off or with (recirculated air) engaged and A/C off. • Do not put objects under the front seats that will i...

AUTOMATIC TEMPERATURE CONTROL SYSTEMS Dual Automatic Temperature Control (DATC) Sony system(if equipped) Note: Your climate control system is touch sensitive. You need only lightly touch the control graphic to activate the feature. Note: Your vehicle is also equipped with touchscreen climate control...

3. (Recirculated air): Press to activate/deactivate air recirculation in the vehicle. Recirculated air may reduce the amount of time to cooldown the interior of the vehicle and may also help reduce undesiredodors from reaching the interior of the vehicle. Recirculated air engagesautomatically when M...

3. MAX A/C: Distributes recirculated air through the instrument panel vents to cool the vehicle. This re-cooling of the interior air is moreeconomical and efficient. Recirculated air may also help reduceundesirable odors from entering the vehicle. Touch MAX A/C again fornormal A/C operation. 4. A/C ...

Operating tips • To reduce fog build-up on the windshield during humid weather,select (defrost) or (floor/defrost). • To reduce humidity build-up inside the vehicle, do not drive with thesystem off or with (recirculated air) engaged and A/C off. • Do not put objects under the front seats that will i...

• Press to control the cooled seat (if equipped). Refer to Cooled seats in the Seating and Safety Restraints chapter. • Press and hold MyTemp to select a temperature you would like thevehicle to remember and maintain for you. Rear controls To access, press ‘Rear’ in the lower right corner . When the...

• Panel On • Panel Floor On • Floor On • Windshield Floor On • Temperature High • Temperature Low • Fan Increase • Fan Decrease • Temperature • Temperature Increase • Temperature Decrease • Temperature <15.5–29.5> degrees • Temperature <59–86> degrees • My Temp • Help *Note: If you have ...

REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel or in thetouchscreen display (if equipped). Press the rear defroster control R to clear the rear window of thin ice and fog. The ignition must be in the on position to operate the rear window defroster. The defroster...

Automatic climate control For hot weather conditions: • The interior cabin will be set to 72°F (22°C). • The cooled seats (if equipped and if the feature is selected to AUTOin the message center) will be set to high. For cold weather conditions: • The interior cabin will be set to 72°F (22°C). • The...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps,license plate lamps and tail lamps. Turns the headlamps on. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the hea...

3. Rotate the headlamp control to the off position. 4. Turn the vehicle on. 5. Turn the vehicle off. 6. Turn the headlamp control to the autolamp position (the headlightsshould turn on). 7. Turn the headlamp control to the off position when the desired delaytime (up to three minutes) has been reache...

Flash-to-pass Pull toward you slightly to activateand release to deactivate. Daytime running lamps (DRL) (if equipped) To activate DRL: • the ignition must be in the on position and • the headlamp control is in the or position • the transmission is not in P (Park). WARNING: Always remember to turn o...

Dome lamp control Use to manually turn the dome lampon. • Press the control. This will turnon the interior courtesy lights.The lights will remain on until thecontrol is pressed again. Dome lamp control (with fog lamps) Use to manually turn the dome lampon. • Press the bottom of the control.This will...

5. Locate the vertical adjuster foreach headlamp. Using a Phillips #2screwdriver, turn the adjustercontrol either clockwise (to adjustdown) or counterclockwise (toadjust up). Note: HORIZONTAL AIMING IS NOT REQUIRED FOR THISVEHICLE AND ISNON-ADJUSTABLE. TURN SIGNAL CONTROL The turn signal lever does ...

INTERIOR LAMPS Front row map lamps (if equipped) To turn on the map lamps, press theouter edge of the clear lens. Thefront row map lamp lights when: • any door is opened. • the instrument panel dimmerbutton is pressed until thecourtesy lamp comes on. • the remote entry controls arepressed and the ig...

Third row cargo lamp The dome lamp lights when: • any door is opened. • the instrument panel dimmerbutton is pressed until thecourtesy lamp comes on. • any of the remote entry controlsare pressed and the ignition isoff. The courtesy lamp can also beturned on and off manually bypressing the control s...

Replacing interior bulbs Check the operation of the bulbs frequently. To replace any of theinterior bulbs, see a dealer or qualified technician. Replacing exterior bulbs Check the operation of all the bulbs frequently. Replacing headlamp bulbs 1. Make sure that the headlamp control is in the off pos...

5. Pull the bulb straight out of thesocket. Reverse steps to reinstall bulb(s). Replacing sidemarker bulbs 1. Make sure that the headlampcontrol is in the off position. 2. Open the hood. 3. Remove the hood overslambumper tower to service sidemarkerbulb (if needed). Lights 85 2011 Explorer (exp) Owne...

4. Rotate the bulb socketcounterclockwise and remove itfrom the lamp assembly. 5. Pull the bulb straight out of thesocket. Reverse steps to reinstall bulb(s). Replacing turn/backup lamp bulbs The turn/backup lamp bulbs are located in the same area of the tail lampassembly, one below the other. Follo...

WINDSHIELD WIPERS Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Speed dependent wipers (ifequipped): When the wiper control is set to any of the interval settingsexcept the longest pause setting...

Windshield washer: Press the end of the stalk: • briefly: causes the wipers toswipe three times with washerfluid. • a long press and hold: the wipersand washer fluid will be activatedfor up to ten seconds. Mist wipe: Press the stalk down and release for a single swipe of the wipers without washer fl...

For rear wash cycle, rotate (and hold as desired) the rear wiper/washercontrol to either position. From either position, the control will automatically return to the 2 or O(off) position. Reverse wiper feature: The rear wiper will be automatically activated in an intermittent setting when shifting i...

ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on thevisor mirror lamp. Slide-on-rod feature Rotate the visor towards the sidewindow and extend it rearward foradditional sunlight coverage. Note: To stow the visor back into the headliner, visor must beretracted before moving it ...

The power outlet is not designed for the following electric appliances;they may not work properly: • Cathode ray tube type televisions • Motor loads, such as vacuum cleaners, electric saws and other electricpower tools, compressor-driven refrigerators, etc. • Measuring devices, which process precise...

automatically reverse direction and move down. This is known as“bounce-back”. If the ignition is turned off (without accessory delaybeing active) during bounce-back, the window will move down until thebounce-back position is reached. Security override To override a bounce-back condition, within two ...

The mirror will automatically return to the normal state whenever thevehicle is placed in R (Reverse) to ensure a bright clear view whenbacking up. Do not block the sensors on the front and back of the interiorrear view mirror since this may impair proper mirrorperformance. Note: A rear center passe...

Heated outside mirrors (if equipped) Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated. Do not remove ice from themirrors with a scraper orattempt to readjust the mirrorglass if it is frozen in place.These actions could cause damage to the glass...

Signal indicator mirrors (if equipped) When the turn signal is activated, the outer portion of the appropriatemirror housing will blink. This provides an additional warning to otherdrivers that your vehicle is about to turn. Blind spot mirrors (if equipped) Your vehicle may be equipped with blind sp...

Using speed control The speed controls are located on the steering wheel. The followingbuttons work with speed control: SET: Press to set a speed or to increase or decrease the set speed. RES (Resume): Press to resume the set speed. CNCL (Cancel): Press to cancel the set speed. ON/OFF: Press to turn...

WARNING: Always pay close attention to changing road conditions, especially when using adaptive cruise control. Adaptive cruise control cannot replace attentive driving. Failing tofollow any of the warnings below or failing to pay attention to the roadmay result in a collision, serious injury or dea...

Setting adaptive cruise control 1. Press and release ON. Themessage center will display thegray ACC indicator light, current gap setting and SET. 2. Accelerate to the desired speed. 3. Press SET upward and release.The vehicle speed will be stored in the memory and the message centerwill display a gr...

Blocked sensor If a message regarding a blockedsensor is displayed, the radar signalsfrom the sensor have beenobstructed. The sensor is locatedbehind a fascia cover near the driverside of the lower grille. When theradar signals are obstructed, avehicle ahead cannot be detectedand the ACC will not fu...

WARNING: Do not use ACC when towing a trailer with brake controls. Aftermarket trailer brakes will not function properly when ACC is activated because the brakes are electronically controlled.Failing to do so may result in loss of vehicle control, which could resultin serious injury. WARNING: Do not...

Navigation/SYNC 威 system hands-free control features (if equipped) Press to active the voice recognition feature. Refer to Voice recognition feature in the MyFord Touch™ / MyLincoln Touch™ supplement. Press to access phone features. Refer to Phone features in the MyFord Touch™ / MyLincolnTouch™ supp...

FCC and RSS-210 Industry Canada Compliance The Car2U 威 system complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following twoconditions: (1) This device may not cause harmful interference, and (2)This device must accept any interference received ...

CARGO AREA FEATURES Cargo net (if equipped) The cargo net secures lightweightobjects in the cargo area. Attach thenet to the loops and anchorsprovided. WARNING: This net is not designed to restrain objects during a collision. Driver Controls 120 2011 Explorer (exp) Owners Guide, 4th PrintingUSA (fus...

Utility hook The utility hook can be used tohang small items such as grocerybags, etc. Do not hang more than10 lb (4.5 kg) on the hook. MANUAL LIFTGATE (IF EQUIPPED) The liftgate area is only intended for cargo, not passengers. To open the liftgate, press thebutton located in the top of theliftgate ...

If the liftgate reverses and starts to close after an open request, a fastcontinuous chime indicates excessive load on the gate or a possible strutfailure. If any excessive load is removed and you still have a fasterchime, have the system serviced immediately by your authorized dealer. Do not attemp...

To set the height of the open liftgate: 1. Open the liftgate. 2. Manually move the liftgate to the desired height. 3. Press and hold the control button on the liftgate until a chime isheard, indicating the new height has been programmed. Note: If the liftgate position is too low, the height cannot b...

Your vehicle may be equipped withfactory or dealer-installed crossbarsthat may be easily adjusted toaccommodate a wide range of roofmounted accessories. To adjust crossbar position (ifequipped): 1. Loosen the tie-down hooks atboth sides of the crossbar byturning counterclockwise. (A smallscrewdriver...

KEYS Integrated keyhead transmitters (IKTs) (if equipped) Your vehicle may be equipped withtwo integrated keyhead transmitters(IKTs). The key blade functions as aprogrammed key which starts thevehicle and unlocks/locks thedriver’s door. The transmitterportion functions as the remoteentry transmitter...

The IA key also contains aremovable mechanical key bladethat can be used to unlock thedriver door. To release themechanical key blade, slide therelease on the back of thetransmitter and pull the blade out. Your IA keys are programmed toyour vehicle. You cannot enter or start your vehicle with anunpr...

POWER DOOR LOCKS • Press the control to unlock all doors. • Press the control to lock all doors. Smart unlocks for integrated keyhead transmitter (IKT) This feature helps to prevent you from locking yourself out of the vehicleif your key is still in the ignition. When you open one of the front doors...

CHILDPROOF DOOR LOCKS • When these locks are set, therear doors cannot be opened fromthe inside. • The rear doors can be openedfrom the outside when thechildproof door locks are set, butthe doors are unlocked. The childproof locks are located onthe rear edge of each rear door andmust be set separate...

The transmitter allows you to: • remotely unlock the vehicle doors . • remotely lock all the vehicle doors . • remotely open the power liftgate (if equipped) . • remotely start/stop the vehicle (if equipped) . Refer to Remote start later in this section. • activate the personal alarm . • arm and dis...

To lock the doors, press and hold for half a second the lock area (blackbutton) on either front door handle. Activating intelligent access at the liftgate: If your IA key is within 3 feet (1 meter) of the liftgate, you can activate your intelligent accesssystem by pressing the exterior liftgate rele...

Replacing the battery The integrated keyhead transmitter (IKT) or intelligent access key (IAkey) uses one coin type three-volt lithium battery CR2032 or equivalent. To replace the battery: Integrated keyhead transmitter (IKT) 1. Twist a thin coin in the slot nearthe key ring to remove the batterycov...

2. Remove the old battery. Note: Please refer to local regulations when disposing oftransmitter batteries. 3. Insert the new battery. Refer tothe instructions inside the IA keyfor the correct orientation of thebattery. Press the battery down toensure that the battery is fullyseated in the battery ho...

Illuminated exit When all vehicle doors are closed, the ignition is turned off and the keyis removed from the ignition (IKT only), the interior dome lamps,parking lamps and the puddle lamps (if equipped) will illuminate. The lamps will turn off if all the doors remain closed and • 25 seconds elapse,...

To help make the vehicle as comfortable as possible, the engine idle canbe increased during a remote start. You can enable or disable engine idleincrease by selecting Remote Start Quiet in the message center. Refer to Message center in the Instrument Cluster chapter. Many states and provinces have r...

Note: If the vehicle has been remote started and is equipped with an IKT, you must turn the ignition on before driving the vehicle. If equippedwith an IA transmitter, you must press the START/STOP button on theinstrument panel once while applying the brake pedal before driving thevehicle. The power ...

SECURICODE™ KEYLESS ENTRY SYSTEM (IF EQUIPPED) You can use the keyless entrykeypad to: • lock or unlock the doors withoutusing a key. • recall memory seat/power mirrorspositions (if equipped). • enable/disable autolock andautounlock. • program/erase user codes. • arm/disarm the perimeter alarmsystem...

Tips: • Do not set a code that uses five of the same number. • Do not use five numbers in sequential order. • The factory set code will work even if you have set your own personalcode. Erasing personal code 1. Enter the factory set 5–digit code. 2. Within five seconds, press the 1 • 2 on the keypad ...

SECURILOCK 姞 PASSIVE ANTI-THEFT SYSTEM SecuriLock 威 passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from beingstarted unless a coded integrated keyhead transmitter (IKT) or intelligent access keys programmed to your vehicle is used. Th...

Replacement of integrated keyhead transmitters (IKT) or intelligentaccess keys Note: Your vehicle comes equipped with two integrated keyhead transmitters (IKTs) or two intelligent access keys. The integrated keyhead transmitter (IKT) functions as both a programmed ignition key that operates all the ...

• If two previously programmed coded keys are not available, you musttake your vehicle to your authorized dealer to have the spare key(s)programmed. Please read and understand the entire procedure before you begin. 1. Insert the first previously programmed coded key into the ignition. 2. Turn the ig...

8. Verify that the remote entry functions operate (press lock thenunlock, making sure you end in unlock) and that the vehicle starts withnew intelligent access key. If the intelligent access key has been successfully programmed, it can beused to activate the intelligent access with push button start...

WARNING: To minimize the risk of neck injury in the event of a crash, head restraints must be installed properly. Tilting head restraints (if equipped) The front head restraints may have a tilting feature for extra comfort. Totilt the head restraint, do the following: 1. Adjust the seatback to an up...

• Move the control in the directionsshown to move the seat forwardor backward. • Press the control to recline theseatback forward or rearward. Using the power lumbar support (if equipped) The power lumbar control is located on the outboard side of the seat. Press the forward/rearward side ofthe cont...

WARNING: Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physicalconditions, must exercise care when using the seat heater. The seatheater may cause burns even at low temperatures, e...

Note: Do not do the following: • Place heavy objects on the seat • Operate the seat heater if water or any other liquid is spilled on theseat. Allow the seat to dry thoroughly. To operate the heated seats: Press the heated seat symbol/buttonto cycle through the various heatsettings and off. Warmer s...

• There is a filter located undereach front seat. • The filter can be accessed from the rear of the seat. Move the frontseat to full up to ease access. To remove an air filter: 1. Remove key from ignition. 2. Push up on the outside rigid edgeof the filter until the tabs arereleased, then rotate the ...

To install a filter: 1. First, position the filter in itshousing making sure that the farforward end is all the way up in thehousing. 2. Push in on the center of theoutside edge of the filter and rotateup into the housing until it clips intoposition. Memory feature (if equipped) This system allows a...

To remove the outboard head restraint, start with it folded and thenpress and hold both unlock/remove buttons and pull it upwards. To reinstall the head restraint, do the following: 1. Insert the two stems into the guide sleeves. 2. Push the head restraint down until it locks. Second row center seat...

Adjusting second row bucket and bench seat back Lift the handle to adjust seatback.Using same control will fold theseatback flat. Note: For the bench seat only, make sure the center safety belt isunbuckled before folding theseatback. WARNING: Always drive and ride with your seatback upright and the ...

2nd row power fold and tumble seat (six–passenger vehicles only) WARNING: Ensure that the seat is unoccupied when folding it down. Folding the seat while occupied could result in occupant injury or damage to the seat. Press and hold the control locatedat the back of the rear door openingone time to ...

4. To return the seatback to theupright position • Lift the seatback toward the rearof the vehicle, and • Rotate the seatback until youhear a click, locking it in theupright position. Note: The seatback will not raise if the rear latch hooks are notproperly engaged to the floorstriker. If the seatba...

Stowing the third row seat (manual seat) 1. Remove all objects from the seatand stowage tub. 2. Fold the outboard head restraintby pulling the head restraint releasestrap. 3. From the rear of the vehicle, foldthe seatback by pulling and holdingthe number 1 strap while pushingthe seatback forward. Re...

2. To return the seatback to uprightposition, pull the number 1 strap,then while holding the number 1strap, pull the long strap located onthe seatback to raise the seatback. 3. Pull the head restraints up totheir normal positions. WARNING: Ensure seat is latched to vehicle floor by pushing/pulling o...

How does the Personal Safety System™ work? The Personal Safety System can adapt the deployment strategy of yourvehicle’s safety devices according to crash severity and occupantconditions. A collection of crash and occupant sensors providesinformation to the Restraints Control Module (RCM). During a ...

Front passenger sensing system For airbags to do their job they must inflate with great force, and thisforce can pose a potentially deadly risk to occupants that are very closeto the airbag when it begins to inflate. For some occupants, this occursbecause they are initially sitting very close to the...

Restraint of pregnant women WARNING: Always ride and drive with your seatback upright and the safety belt properly fastened. The lap portion of the safety belt should fit snug and be positioned low across the hips. Theshoulder portion of the safety belt should be positioned across thechest. Pregnant...

When to use the automatic locking mode This mode should be used any time a child safety seat, except a booster, is installed in passenger front or rear seating positions. Children12 years old and under should be properly restrained in a rear seatingposition whenever possible. Refer to Safety restrai...

WARNING: BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the safety belt assembly “automatic locking retractor” feature or any other safety belt function is not operatingproperly when checked by an authorized dealer. Failure to replace thebelt and retractor assembly could increase the risk of injury...

Safety belt extension assembly If the safety belt is too short when fully extended, there is an 8 inch(20 cm) safety belt extension assembly that can be added (part number611C22). This assembly can be obtained from an authorized dealer. Safety belt extensions are vehicle specific. Please see an auth...

Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and achime sounds to remind the occupants to fasten their safety belts. Conditions of operation If... Then... The driver’s safety belt is notbuckled before the ignitionswitch is turned t...

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... “Crashes are rare events” 36700 crashes occur every day. The more we drive, the more we areexposed to “rare” events, even forgood drivers. 1 in 4 of us will be ser...

Reasons given... Consider... “I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate in rear andside crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likelyto DIE. Safety be...

WARNING: Modifying or adding equipment to the front end of the vehicle (including frame, bumper, front end body structure and tow hooks) may affect the performance of the airbag system, increasingthe risk of injury. Do not modify the front end of the vehicle. Children and airbags Children must alway...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

• a readiness light and tone. • diagnostic module. • the electrical wiring which connects the components. • Front passenger sensing system. Refer to Front passenger sensing system later in this chapter. • “Passenger airbag off” or “pass airbag off” indicator lamp. Refer to Front passenger sensing sy...

Passenger airbag status indicator The front passenger sensing systemuses a passenger airbag statusindicator which will illuminateindicating that the front passengerfrontal airbag is either ON (enabled)or OFF (disabled). The indicatorlamp is located in the center stackof the instrument panel. Note: T...

• Objects stowed in the seatback map pocket (if equipped) • Objects placed on the occupant’s lap • Cargo interference with the seat • Other passengers pushing or pulling on the seat • Rear passenger feet and knees resting or pushing on the seat The conditions listed above may cause the weight of a p...

Seat-mounted side airbag system WARNING: Do not place objects or mount equipment on or near the airbag cover on the side of the seatbacks of the front seats or in front seat areas that may come into contact with adeploying airbag. Failure to follow these instructions may increase therisk of personal...

How does the Safety Canopy 姞 System work? The design and development of theSafety Canopy system includedrecommended testing proceduresthat were developed by a group ofautomotive safety experts known asthe Side Airbag Technical WorkingGroup. These recommended testingprocedures help reduce the risk of...

• A series of five beeps will be heard. The tone pattern will repeatperiodically until the problem and light are repaired. If any of these things happen, even intermittently, have the SRS servicedat your authorized dealer immediately. Unless serviced, the system maynot function properly in the event...

Important child restraint precautions WARNING: Always make sure your child is secured properly in a device that is appropriate for their height, age and weight. Child safety restraints must be purchased separately from the vehicle.Failure to follow these instructions and guidelines may result in ani...

Recommendations for attaching child safety restraints for children RestraintType Child Weight Use any attachment method as indicated below by “X” LATCH(loweranchorsandtoptetheranchor) LATCH(loweranchorsonly) Safetybeltandtoptetheranchor Safetybelt andLATCH(loweranchorsand toptetheranchor) Safetybelt...

WARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision, which may result in serious injury ordeath. WARNING: Never use pillows, books, or towels to boost a child. They can slide around and increase ...

Follow all the safety restraint and airbag precautions that apply to adultpassengers in your vehicle. If the child is the proper height, age, and weight (as specified by yourchild safety seat or booster manufacturer), fits the restraint and can berestrained properly, then restrain the child in the c...

Installing child safety seats with combination lap and shoulderbelts Check to make sure the child seat is properly secured before each use.Children 12 and under should be properly restrained in a rear seatingposition whenever possible. If all children cannot be seated andrestrained properly in a rea...

Note: The ’Lock-off’ device on some child restraints may not accommodate the shoulder portion of the inflatable safety belt. Follow allinstructions provided by the manufacturer of the child restraintregarding the necessary and proper use of the ’Lock-off’ device. In someinstances these devices have ...

5. To put the retractor in the automatic locking mode, do the following: • Standard safety belt: grasp theshoulder portion of the belt andpull downward until all of the beltis pulled out. • Inflatable safety belt: grasp thelap portion of the inflatable safetybelt and pull upward until all ofthe belt...

Follow the instructions on attaching child safety seats with tether straps.Refer to Attaching child safety seats with tether straps later in this chapter. Attach LATCH lower attachments of the child seat only to the anchorsshown. WARNING: Never attach two child safety seats to the same anchor. In a ...

Once the child safety seat has been installed, using either the safety belt,the lower anchors of the LATCH system, or both, you can attach the toptether strap. If you install a child seat with rigid LATCH attachments, do not tightenthe tether strap enough to lift the child seat off the vehicle seat ...

If the tether strap is clipped incorrectly, the child safety seat may not beretained properly in the event of a collision. 4. Tighten the child safety seat tether strap according to themanufacturer’s instructions. If the safety seat is not anchored properly, the risk of a child beinginjured in a col...

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, and lets you adjust the shoulder belt to cross the chest andrest snugly near the center of the shoulder. The drawings below comparethe ideal fit (cente...

Follow all instructions provided by the manufacturer of the booster seat. WARNING: Never place, or allow a child to place, the shoulder belt under a child’s arm or behind the back because it reduces the protection for the upper part of the body and may increase the riskof injury or death in a collis...

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare encountered on streets,highways and off-road. Utilityvehicles and trucks are not designedfor cornering at speeds as high aspassenger cars any more tha...

VEHICLE CHARACTERISTICS Four-wheel drive (4WD) system (if equipped) A vehicle equipped with 4WD (when selected) has the ability to use allfour wheels to power itself. This increases traction which may enable youto safely drive over terrain and road conditions that a conventionaltwo-wheel drive vehic...

How your vehicle differs from other vehicles SUVs and trucks can differ fromsome other vehicles in a fewnoticeable ways. Your vehicle maybe: • Higher – to allow higher loadcarrying capacity and to allow itto travel over rough terrainwithout getting hung up ordamaging underbody components. • Shorter ...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING Tire Quality Grades apply to newpneumatic passenger car tires. TheQuality grades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperature A These Tire Quality G...

WARNING: Under-inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or “blowout”, with unexpected loss of vehicle control and increasedrisk of injury. Under-inflation increases sidewall flexing and rollingresistance, resulting in heat buildup a...

Note: If you have to drive a distance to get air for your tire(s), check and record the tire pressure first and add the appropriate air pressurewhen you get to the pump. It is normal for tires to heat up and the airpressure inside to go up as you drive. 2. Remove the cap from the valve on one tire, ...

Improper or inadequate vehicle maintenance can cause tires to wearabnormally. Inspect all your tires, including the spare, frequently, andreplace them if one or more of the following conditions exist: Tire wear When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to help pre...

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers toplace standardized information on the sidewall of all tires. Thisinformation identifies and describes the fundamental characteristics ofthe tire and also provides a U.S. DOT Tire Identific...

Safety practices Driving habits have a great deal to do with your tire mileage and safety. • Observe posted speed limits • Avoid fast starts, stops and turns • Avoid potholes and objects on the road • Do not run over curbs or hit the tire against a curb when parking WARNING: If your vehicle is stuck...

The tires should also be balanced periodically. An unbalanced tire andwheel assembly may result in irregular tire wear. Tire rotation Rotating your tires at the recommended interval (as indicated in the Scheduled Maintenance chapter) will help your tires wear more evenly, providing better tire perfo...

7. H: Indicates the tire’s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods oftime under a standard condition of load and inflation pressure. The tireson your vehicle may operate at different conditions for load and inflationpressure. The...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below. Note: Tire Quality Grades do not apply to this type of tire. 1. LT: Indicates a tire, designated by the Tire a...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. Tire Quality Grades donot apply ...

following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that may cause undesired operation. WARNING: The tire pressure monitoring system is NOT a substitute for manually checking tire pressure. The ...

To restore the full functionality of the tire pressure monitoring system,have the damaged road wheel/tire repaired and remounted on yourvehicle. For additional information, refer to Changing tires with a TPMS in this section. When you believe your system is not operating properly The main function o...

Low tirepressurewarning light Possible cause Customer action required Flashingwarning light Spare tire in use Repair the damaged road wheel/tire and reinstall it on the vehicle torestore system functionality. For adescription on how the systemfunctions, refer to When your temporary spare tire is ins...

SNOW TIRES AND CABLES WARNING: Snow tires must be the same size, load index, speed rating as those originally provided by Ford. Use of any tire or wheel not recommended by Ford can affect the safety andperformance of your vehicle, which could result in an increased risk ofloss of vehicle control, ve...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehi...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

• Example only: WARNING: Exceeding the Safety Compliance Certification Label vehicle weight rating limits could result in substandard vehicle handling or performance, engine, transmission and/or structuraldamage, serious damage to the vehicle, loss of control and personalinjury. Tires, Wheels and Lo...

GCW (Gross Combined Weight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer. GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo andpassengers – that the vehicle can handle without r...

WARNING: Do not use replacement tires with lower load carrying capacities than the original tires because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tireswith a higher limit than the original tires do not increase the GVWRand GAWR limitations. WARNING: Exceeding any vehicle ...

TRAILER TOWING Trailer towing with your vehicle may require the use of a trailer towoption package. An optional Class III towing hitch is available and may berequired for your towing purposes. Trailer towing puts additional loads on your vehicle’s engine,transmission, axle, brakes, tires and suspens...

Engine/Passengers/Trailer Class Maximum GCWR - lb (kg) Maximum Trailer Weight - lb (kg) FWD vehicles 3.5L/6–passenger/Class I 6870 (3116) 2000 (907) 3.5L/7–passenger/Class I 6880 (3121) 2000 (907) 3.5L/6–passenger/Class III 9910 (4495) 5000 (2268)* 3.5L/7–passenger/Class III 9920 (4500) 5000 (2268)*...

4. Measure the height of the top of the front wheel opening on thefender a second time, this is H2. 5. Install and adjust the tension in the weight distributing bars so thatthe height of the front fender is approximately halfway between H1 andH2. 6. Check that the trailer is level. If not level, adj...

Trailer lamps Trailer lamps are required on most towed vehicles. Make sure all runninglights, brake lights, turn signals and hazard lights are working. Contactyour authorized dealer or trailer rental agency for proper instructionsand equipment for hooking-up trailer lamps. WARNING: Never connect any...

STARTING Positions of the ignition (if equipped) If your vehicle is equipped with a push button start system, refer to Push button start system in this section for ignition modes. 1. Off— locks the gearshift leverand allows key removal. Thisposition also shuts the engine andall electrical accessorie...

Note: Cranking may be stopped at any time by turning the key to the off position. 3. After idling for a few seconds, release the parking brake, apply thebrake, shift into gear and drive. Note: If the engine does not start on the first try, turn the vehicle to the off position, wait 10 seconds and tr...

3. On — press the START/STOP button two times without applying thebrake pedal. This will power your vehicle’s electrical system and thewarning lights in the instrument cluster will illuminate, but the enginewill remain off. Note: You can start the engine from any ignition mode. 4. Start — press the ...

Switching the vehicle off when not in P (Park): It is recommended that you shift into the P (Park) position before switching your vehicleoff. If you switch your vehicle off with the shifter in any position otherthan P (Park), the message SHIFT TO PARK will be displayed in themessage center. If the v...

• Be sure that areas where the vehicle is parked are clean and clear ofall combustibles such as petroleum products, dust, rags, paper andsimilar items. • Be sure that the engine block heater, heater cord and extension cordare solidly connected. A poor connection can cause the cord tobecome very hot ...

brake pedal pulsation may be observed during ABS braking and thebrake pedal may suddenly travel a little farther as soon as ABS braking isdone and normal brake operation resumes. These are normalcharacteristics of the ABS and should be no reason for concern. Using ABS When hard braking is required, ...

Parking brake Apply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops. The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned on) until theparking brake is released....

To turn off traction control in the AdvanceTrac 威 system, select traction control off in the message center. Full features of the AdvanceTrac 威 system can be restored by selecting it on again or by turning off andrestarting the engine. If you switch off traction control inthe AdvanceTrac 威 with RSC ...

Hill descent control can maintain vehicle speeds on downhill gradesbetween 3 mph (5 km/h) and 20 mph (32 km/h). Above 20 mph(32 km/h), the system remains armed, but descent speed cannot be setor maintained. WARNING: Hill descent control does not provide hill hold at zero mph (0 km/h). When stopped, ...

• At speeds above 20 mph (32 km/h): When the HDC button is pressed,the HDC system will be enabled, the light on the button will beilluminated, and FOR HILL CNTRL, 20 MPH OR LESS will bedisplayed in the message center for several seconds. • For HDC to enable, the vehicle must be in a drive gear or (R...

WARNING: Loaded vehicles, with a higher center of gravity, may handle differently than unloaded vehicles. Do not overload your vehicle and use extra precautions, such as driving at slowerspeeds, avoiding abrupt steering changes and allowing for increasedstopping distance, when driving a heavily load...

M (Manual) This vehicle may be equipped with a SelectShift Automatic™transmission (SST) gearshift lever. SST is an automatic transmission withthe ability for the driver to change gears up or down. By moving thegearshift lever from D (Drive) to M (Manual), you now have control ofselecting the gear yo...

If your vehicle gets stuck in mud or snow If your vehicle gets stuck in mud or snow, it may be rocked out byshifting between forward and reverse gears, stopping between shifts in asteady pattern. Press lightly on the accelerator in each gear. Note: Do not rock the vehicle if the engine is not at nor...

REARVIEW CAMERA SYSTEM (IF EQUIPPED) The rear video camera system,located on the liftgate above thelicense plate, provides a video imageof the area behind the vehicle. Itadds assistance to the driver whilereversing or reverse parking thevehicle. To use the rear videocamera system, place thetransmiss...

To use active guidelines, turn the steering wheel and point the activeguidelines towards an intended path. If the steering wheel position ischanged while reversing, the vehicle might deviate from the originalintended path. Active guidelines project the intended path of the vehicle. Fixedguidelines s...

Press (+) or (-) to manually adjust the zoom levels. You can choose from OFF, Level 1, Level 2 and Level 3. The selected level willappear between the buttons (i.e. Level 1). When activating manual zoommode, the system always starts from OFF. When enabled, Level 1, Level 2, or Level 3 will only be ac...

Night time and dark area use At night time or in dark areas, the camera system relies on the reverselamp lighting to produce an image. Therefore, it is necessary that bothreverse lamps are operating in order to get a clear image in the dark. Ifeither of the lamps are not operating, stop using the ca...

Operation The radar sensor detects vehiclesahead that are moving in the samedirection as your vehicle. If the radar detects that yourvehicle is rapidly closing on anothervehicle a red warning light willilluminate and an audible warningchime will sound. After that, if the risk of collisionfurther inc...

Activating/deactivating collision warning system To turn the warning system and/or chime on or off and set the warningsensitivity <– –>, refer to Message center in the Instrument Cluster chapter. Note: If the system cannot be turned off in a MyKey™ equipped vehicle, refer to MyKey™ in the Lock...

Automatic search for parking space To start, press the APA controlswitch (on the left side of theinstrument panel below theheadlamp switch). The touch screenwill display SEARCHING FORPARKING SPACE ON RIGHT(LEFT/SIDE) and a correspondinggraphic. To designate what side ofthe street to search on, use t...

Automatic steering into parking space Automatic steering is activated when you stop the vehicle, remove yourhands from the steering wheel and select the R (Reverse) gear. Be sure thesteering wheel motion is not obstructed by any objects. The vehicle willsteer itself from this point on as you follow ...

Troubleshooting Why isn’t APA searching for a parking space? • You may have deactivated the AdvanceTrac 威 system. • One of the doors (except the driver’s door) may not be securely closed. Why doesn’t APA offer a particular parking space? • Something may be contacting the front bumper or side sensors...

• The parking space length or parked objects position have changedafter the vehicle has passed the parking space. • The temperature around your vehicle changes quickly, such as drivingfrom a heated garage into the cold, or after leaving a car wash. As aresult, the outside air temperature displayed i...

BLIND SPOT INFORMATION SYSTEM (BLIS 姞 ) WITH CROSS TRAFFIC ALERT (CTA) (IF EQUIPPED) The BLIS 威 is a convenience feature that aids the driver in assessingwhether a vehicle is within an areaon either side of the vehicleextending rearward from the outsidemirrors to approximately 10 feet(3 meters) beyo...

Cross traffic alert (CTA) system operation The CTA system warns the driver of approaching vehicles when R(Reverse) is selected and the vehicle is backing out of a front-in parkingspot. It sounds a series of tones and flashes the BLIS 威 indicator found on the exterior mirror on the side of the approa...

CTA coverage also decreases when parking at shallow angles (refer tofigure for approximate zone coverage areas [sensor obstructed for vehicle on left] ). CTA detection limitations: Due to the nature of radar technology, there may be certain instances where vehicles entering and exiting theblind spot...

CTA and reverse sensing system (RSS) interaction CTA works along with the reverse sensing system (RSS) (if equipped).Become familiar with the warning tones of both systems. BLIS 威 and/or CTA on/off and disable operation The BLIS 威 and/or the CTA can be turned off via the message center. If either th...

Trailer tow false alerts When towing a trailer, the sensors may detect the trailer thus causing afalse alert. It may be desirable to turn the BLIS 威 off if the false alerts become annoying. Day and night brightness The BLIS 威 and/or CTA alert will automatically dim when the headlamp switch is in PAR...

Drive cautiously to avoid vehicle damage from concealed objects such asrocks and stumps. You should either know the terrain or examine maps of the area beforedriving. Map out your route before driving in the area. To maintainsteering and braking control of your vehicle, you must have all fourwheels ...

when you are driving over sand, apply the accelerator slowly and avoidspinning your wheels. If the vehicle does slide, steer in the direction ofthe slide until you regain control of the vehicle. If the transmission, transfer case or front axle are submerged in water,their fluids should be checked an...

Apply just enough power to the wheels to climb the hill. Too muchpower will cause the tires to slip, spin or lose traction, resulting in loss ofvehicle control. Descend a hill in the same gear youwould use to climb up the hill toavoid excessive brake applicationand brake overheating. Do notdescend i...

If the terrain management system becomes inoperable, it may not bepossible to select specific modes and a message will be displayed. If theTMS becomes inoperable due to a system malfunction, all of the modeindicators on the control will turn off and the message center will displayone of the followin...

ROADSIDE ASSISTANCE Vehicles sold in the U.S. : Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24-hours,...

Vehicles sold in the U.S. : Using roadside assistance Complete the roadside assistance identification card and place it in yourwallet for quick reference. This card is found in the Owner’s Guideportfolio in the glove compartment. U.S. Ford vehicle customers who require Roadside Assistance, call1-800...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses 2A Grey Grey — — 3A Violet Violet — — 4A Pink Pink — — 5A Tan Tan — — 7.5A Brown Brown — — 10A Red Red — — 15A Blue Blue — — 20A Yellow Yellow Yellow Blue 25A Natural Natural — — 30A G...

The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Protected Circuits 1 30A One touch up/down driver sidefront window 2 15A Not used (spare) 3 30A One touch up/down passengerside front window 4 10A Interior demand lamps (overheadconsole, 2nd row, cargo), glovebox lamp, 2nd and 3rd r...

Fuse/Relay Location Fuse Amp Rating Protected Circuits 9 10A 4” Radio display (withoutSYNC 威 ), Power liftgate logic, Electronic finish panel 10 10A Run/accessory relay (wipers, rearwasher), Rain sensor 11 10A Instrument cluster, Heads-updisplay 12 15A Interior courtesy lamps (overheadconsole, 2nd r...

Fuse/Relay Location Fuse Amp Rating Protected Circuits 45 5A Not used (spare) 46 10A Climate control module 47 15A Fog lamps, left and right turnsignal mirror feed 48 30A Circuit Breaker Rear power windows, Passengerpower window, One touch down(driver side only) 49 Delayed accessory relay Body contr...

CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily.Instead, gradually decrease your speed. Hold the steering wheel firmlyand slowly move to a safe place on the side of the road. Note: The tire pressure monitoring system (TPMS) indicator light will illuminate when...

The usage of a full-size dissimilar spare tire/wheel can lead toimpairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability • All-Wheel driving capability (...

Tire change procedure WARNING: When one of the front wheels is off the ground, the transaxle alone will not prevent the vehicle from moving or slipping off the jack, even if the vehicle is in P (Park). WARNING: To help prevent the vehicle from moving when you change a tire, be sure to place the tran...

1. Air compressor (inside) 2. Diverter knob 3. On/Off button 4. Air pressure gauge 5. Deflation button 6. Sealant bottle/canister 7. Sealant filling clear tube 8. Sealant tube — tire valveconnector 9. Yellow cap tool 10. Air compressor hose 11. Air hose — tire valve connector 12. Accessory power plu...

Tips for use of the temporary mobility kit Read the following list of tips to ensure safe operation of the temporarymobility kit: • Before operating the temporary mobility kit, make sure your vehicle issafely off the road and away from moving traffic. Turn on the hazardlights. • Always set the parki...

10. Immediately and cautiously, drive the vehicle 4 miles (6 km) to distribute the sealant evenly inside the tire. Do not exceed50 mph (80 km/h). Note: If you experience any unusual vibration, ride disturbance or noise while driving, reduce your speed until you can safely pull off tothe side of the ...

5. Turn the compressor off by pressing the on/off button. 6. Unplug the hoses, re-install the valve cap on the tire and return thekit to the stowage area. WARNING: The power plug may get hot after use and should be handled carefully while unplugging. What to do after the tire has been sealed After u...

WARNING: When a wheel is installed, always remove any corrosion, dirt or foreign materials present on the mounting surfaces of the wheel or the surface of the wheel hub, brake drum orbrake disc that contacts the wheel. Ensure that any fasteners thatattach the rotor to the hub are secured so they do ...

JUMP STARTING WARNING: The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. WARNING: Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted. Do not attempt to push-start your aut...

Connecting the jumper cables Note: In the illustration, the vehicle on the bottom is used to designate the assisting (boosting) battery. 1. Connect the positive (+) jumpercable to the positive (+) terminal ofthe discharged battery. 2. Connect the other end of thepositive (+) cable to the positive(+)...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift anddollies or flatbed equipment. Do not tow w...

If the vehicle is towed by other means or incorrectly, vehicledamage may occur. Ford Motor Company produces a towing manual for all authorized towtruck operators. Have your tow truck operator refer to this manual forproper hook-up and towing procedures for your vehicle. Emergency towing In case of a...

GETTING THE SERVICES YOU NEED Warranty repairs to your vehicle must be performed by an authorizeddealer. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfaction. Plea...

In Canada: Mailing address (Ford vehicles) Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4 Telephone 1-800-565-3673 (FORD) Online www.ford.ca Mailing address (Lincoln vehicles) Lincoln CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oak...

You can get more information by calling BBB AUTO LINE at1-800-955-5100, or writing to: BBB AUTO LINE4200 Wilson Boulevard, Suite 800Arlington, Virginia 22203–1833 BBB AUTO LINE applications can also be requested by calling the FordMotor Company Customer Relationship Center at 1-800-392-3673. Note: F...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft 威 Detail Wash (ZC-3-A), which is available from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can ...

• Do not spray a hot engine with cold water to avoid cracking theengine block or other engine components. • Spray Motorcraft 威 Engine Shampoo and Degreaser (ZC-20) on all parts that require cleaning and pressure rinse clean. In Canada, useMotorcraft 威 Engine Shampoo (CXC-66-A). • Cover the highlight...

hot wax treatments used by commercial car washes, water repellentcoatings, tree sap, or other organic contamination; these contaminantsmay cause squeaking or chatter noise from the blades, and streaking andsmearing of the windshield. To clean these items, follow these tips: • The windshield, rear wi...

• Do not use household cleaning products or glass cleaners, which canstain and discolor the fabric and affect the flame retardant abilities ofthe seat materials. WARNING: Do not use cleaning solvents, bleach or dye on the vehicle’s safety belts, as these actions may weaken the belt webbing. WARNING:...

FORD AND LINCOLN CAR CARE PRODUCTS Your Ford or Lincoln authorized dealer has many quality productsavailable to clean your vehicle and protect its finishes. These qualityproducts have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement the style andap...

SERVICE RECOMMENDATIONS • Use the scheduled maintenance information to track routine service. • Use only recommended fuels, lubricants, fluids and service partsconforming to specifications. • Your authorized dealer can provide parts and service. PRECAUTIONS WHEN SERVICING YOUR VEHICLE • Do not work ...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel. 2. Go to the front of the vehicle andrelease the auxiliary latch that islocated under the front center ofthe hood. 3. Lift the hood. Maintenance and Specifications 371 2011...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.5L V6 engine 1. Engine coolant reservoir 2. Brake fluid reservoir 3. Battery 4. Power distribution box 5. Air filter assembly 6. Transmission fluid dipstick (out of view) 7. Engine oil dipstick 8. Engine oil filler cap 9. Windshield washer fluid res...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meets Ford specifications. Do not use anyspecial washer fluid such as windshield water repellent type fluid or bugwash. They may cause s...

CHANGING THE WIPER BLADES 1. Pull the wiper blade and armaway from the glass. 2. Squeeze the locking tabs torelease the blade from the arm andpull the blade away from the arm toremove it. 3. Attach the new blade to the arm and snap it into place. Replace wiper blades at least once per year for optim...

3. To attach the new wiper to thewiper arm, align the slot (1) andcross pin (2) and firmly press thewiper arm into the wiper blade untila click is heard. If you find this procedure too difficult, please see your dealer. ENGINE OIL Checking the engine oil Refer to the scheduled maintenance informatio...

Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler capand use a funnel to pour the engine oil...

Do not use supplemental engine oil additives, cleaners or other enginetreatments. They are unnecessary and could lead to engine damage thatis not covered by Ford warranty. Change your engine oil and filter according to the appropriate schedulelisted in the scheduled maintenance information. Ford pro...

WARNING: Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near thebattery, always shield your face and protect your eyes. Always provideproper ventilation. WARNING: When lif...

• If you do not allow the engine to relearn its idle trim, the idlequality of your vehicle may be adversely affected until the idletrim is eventually relearned. When the battery is disconnected or a new battery installed, thetransmission must relearn its adaptive strategy. As a result of this, thetr...

Electrical accessory installation To ensure proper operation of the BMS, any electrical devices that areadded to the vehicle should not have their ground connection madedirectly at the negative battery post. A connection at the negativebattery post can cause inaccurate measurements of the battery co...

When the engine is cold, check the level of the engine coolant in thereservoir. The engine coolant should be withinthe COLD FILL RANGE as listed onthe engine coolant reservoir. Refer to scheduled maintenance information for service interval schedules. If the engine coolant has not been checked at th...

• DO NOT MIX different colors or types of coolant in your vehicle. Make sure the correct coolant is used. Mixing of engine coolants mayharm your engine’s cooling system. The use of an improper coolantmay harm engine and cooling system components and may void thewarranty. Refer to Maintenance product...

4. When you are sure that all the pressure has been released, use thecloth to turn it counterclockwise and remove the cap. 5. Fill the coolant reservoir slowly with the proper coolant mixture, towithin the COLD FILL RANGE or the FULL COLD level on the reservoir.If you removed the radiator cap in an ...

Severe climates If you drive in extremely cold climates: • It may be necessary to increase the coolant concentrationabove 50%. • NEVER increase the coolant concentration above 60%. • A coolant concentration of 60% will provide improved freezepoint protection. Increased engine coolant concentrations ...

What you should know about fail-safe cooling If the engine coolant supply is depleted, this feature allows the vehicle tobe driven temporarily before incremental component damage is incurred.The “fail-safe” distance depends on ambient temperatures, vehicle loadand terrain. How fail-safe cooling work...

Refueling WARNING: Fuel vapor burns violently and a fuel fire can cause severe injuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; ...

4. After you are done pumping fuel, slowly remove the fuel fillernozzle—allow about five seconds after pumping fuel before removing thefuel filler nozzle. This allows residual fuel to drain back into the fuel tankand not spill onto the vehicle. Note: A fuel spillage concern may occur if overfilling ...

Octane recommendations Your vehicle is designed to use“Regular” unleaded gasoline with apump (R+M)/2 octane rating of 87.Some stations offer fuels posted as“Regular” with an octane ratingbelow 87, particularly in high altitude areas. Fuels with octane levelsbelow 87 are not recommended. Do not be co...

3. Fill the vehicle with fuel from the portable fuel container. 4. When done, clean the funnel or properly dispose of it. Extra funnelscan be purchased from your authorized dealer if you choose to disposeof the funnel. Do not use aftermarket funnels; they will not work with the Easy Fuel 威 system an...

• Use a known quality gasoline, preferably a national brand. • Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading(in ...

• Four-wheel-drive operation (if equipped) is less fuel efficient thantwo-wheel-drive operation. • Close windows for high speed driving. EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and acatalytic converter which will enable your vehicle to comply withapp...

BRAKE FLUID The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the MIN andMAX lines are within the normaloperating range; there is no need toadd fluid. If the fluid levels areoutside of the normal operatingrange, the performan...

Use of a non-approved automatic transmission fluid may causeinternal transmission component damage. If necessary, add fluid in 1/2 pint(250 ml) increments through thefiller tube until the level is correct. If an overfill occurs, excess fluidshould be removed by an authorizeddealer. An overfill condi...

6. Replace the air filter housingcover and secure the clamps. Besure that the air cleaner cover tabsare engaged into the slots of the aircleaner housing. Note: Failure to use the correct air filter element may result in severe engine damage. The customer warranty may be void for any damage tothe eng...

Miscellaneous • Make sure all linkages, cables, levers and pins under vehicle arecovered with grease to prevent rust. • Move vehicles at least 25 feet (8 m) every 15 days to lubricateworking parts and prevent corrosion. Removing vehicle from storage When your vehicle is ready to come out of storage,...

FORD CUSTOM ACCESSORIES FOR YOUR VEHICLE A wide selection of Ford Custom Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement the ...

Peace of mind • Keyless entry keypad • Wheel locks • Vehicle tracking and recovery* • Remote start • Cargo shade • Cargo area protector • Vehicle security systems • Bumper and hitch mounted parking sensors* • Locking gas plug for capless fuel system *Ford Licensed Accessories (FLA) are warranted by ...

FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY) More than 30 million Ford and Lincoln owners have discovered thepowerful protection of Ford ESP. It is the only extended service planbacked by Ford Motor Company, and provides “peace of mind”protection beyond the New Vehicle Limited Warranty coverage. Up t...

FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY) You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is the only service contractbacked by Ford Motor Company of Canada, Limited. Depending on theplan you purchase, Ford ESP provides benefits such as: • R...

GENERAL MAINTENANCE INFORMATION Why maintain your vehicle? This guide describes the scheduled maintenance required for yourvehicle. Carefully following this schedule helps protect against majorrepair expenses resulting from neglect or inadequate maintenance andmay also help to increase the value of ...

Genuine Ford parts and service When planning your maintenance services, consider your dealership forall your vehicle’s needs. There are a lot of reasons why visiting your dealership for all yourservice needs is a great way to help keep your vehicle running great. Convenience Many dealerships have ex...

NORMAL SCHEDULED MAINTENANCE AND LOG For your convenience, your vehicle is equipped with a message centerwhich determines the proper oil change service interval. You shouldperform the engine oil change as indicated by the message center. Themessage center will display ENGINE OIL CHANGE SOON or OILCH...

Oil Change S ervice Interval* 1 23456789 1 0 1 1 1 2 1 3 1 4 1 5 Change engine oil and filter • •••••••••••••• Rotate tires, inspect tire wear and measure tread depth • •••••••••••••• Inspect wheels and related components for abnormal noise, wear , looseness or drag • •••••••••••••• Perform multi-po...

Maintenance schedule log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ...

SPECIAL OPERATING CONDITIONS If you operate your vehicle primarily in one of the more demanding conditions listed below, you will need to have some items maintainedmore frequently. If you only occasionally operate your vehicle under these conditions, it is not necessary to perform the additionalmain...

Extensive idling and/or low-speed driving for long distances as in heavy commercial use such as delivery, taxi, patrol car or livery As required – Change engine oil and filter as indicated by messagecenter and perform services listed in the NormalScheduled Maintenance chart (except Fiesta) Inspect f...

Operating in dusty conditions such as unpaved or dusty roads Inspect frequently, service as required – Replace cabin air filter (if equipped) – Replace engine air filter Every 5,000 miles (8,000 km) – Inspect the wheels and related components forabnormal noise, wear, looseness or drag– Rotate tires,...

Special operating condition log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D A...

EXCEPTIONS In addition, there are several exceptions to the Normal Schedule. Theyare listed below: Normal vehicle axle maintenance ❑ Rear axles and power take-off (PTO) units containing synthetic fluid and light duty trucks equipped with Ford-design axlesare lubricated for life. These fluids are not...

ENGINE COOLANT CHANGE RECORD Initial change 6 years or 100,000 miles (160,000 km)(whichever comes first) After initial change Every 3 years or 50,000 miles (80,000 km) Engine coolant change log D EALER V ALIDATION : P&A C ODE : RO#: H OURS : D ATE : M ILEAGE : D EALER V ALIDATION : P&A C ODE...

A Accessory delay ..........................97 Active Park Assist .....................299 Adaptive Cruise Control ...........102 AdvanceTrac ..............................274 Airbag supplemental restraintsystem ........................195, 204, 206 and child safety seats ............197description ...

Overdrive ...................................284 P Parental MyKeyprogramming .............................129 Park Assist ................................299 Parking brake ............................273 Parts(see Motorcraft 威 parts) ...........404 Passenger OccupantClassification Sensor ..............

V Vehicle Identification Number(VIN) ..........................................409 Vehicle loading ..........................252 Ventilating your vehicle ...........269 W Warning lights (see Lights) .......12 Washer fluid ..............................373 Water, Driving through .............319 Wind...